Commit d20ceecd authored by Andy Walls's avatar Andy Walls Committed by Mauro Carvalho Chehab

V4L/DVB (9598): cx18: Prevent CX23418 from clearing it's outgoing ack interrupts to driver

When the CX23418 CPU unit sent out an ack interrupt to the linux driver, it
also received that interrupt and cleared the flag before the linux driver could
see what the interrupt was for.  This fix prevents the CPU from receiving an
IRQ for it's own outgoing ack's to the linux driver.  This fix is critical now
that the linux driver doesn't poll but relies on these ack interrupts.
Signed-off-by: default avatarAndy Walls <awalls@radix.net>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@redhat.com>
parent 2d1a1b05
......@@ -380,6 +380,17 @@ int cx18_firmware_init(struct cx18 *cx)
if (sz <= 0)
return -EIO;
}
/*
* The CPU firmware apparently sets up to receive an interrupt for it's
* outgoing IRQ_CPU_TO_EPU_ACK to us (*boggle*). We get an interrupt
* when it sends us an ack, but by the time we process it, that flag in
* the SW2 status register has been cleared by the CPU firmware.
* We'll prevent that not so useful behavior by clearing the CPU's
* interrupt enables for Ack IRQ's we want to process.
*/
cx18_sw2_irq_disable_cpu(cx, IRQ_CPU_TO_EPU_ACK | IRQ_APU_TO_EPU_ACK);
/* initialize GPIO */
cx18_write_reg_expect(cx, 0x14001400, 0xc78110, 0x00001400, 0x14001400);
return 0;
......
......@@ -262,6 +262,13 @@ void cx18_sw2_irq_disable(struct cx18 *cx, u32 val)
cx18_write_reg(cx, r & ~val, SW2_INT_ENABLE_PCI);
}
void cx18_sw2_irq_disable_cpu(struct cx18 *cx, u32 val)
{
u32 r;
r = cx18_read_reg(cx, SW2_INT_ENABLE_CPU);
cx18_write_reg(cx, r & ~val, SW2_INT_ENABLE_CPU);
}
void cx18_setup_page(struct cx18 *cx, u32 addr)
{
u32 val;
......
......@@ -390,6 +390,7 @@ void cx18_sw1_irq_enable(struct cx18 *cx, u32 val);
void cx18_sw1_irq_disable(struct cx18 *cx, u32 val);
void cx18_sw2_irq_enable(struct cx18 *cx, u32 val);
void cx18_sw2_irq_disable(struct cx18 *cx, u32 val);
void cx18_sw2_irq_disable_cpu(struct cx18 *cx, u32 val);
void cx18_setup_page(struct cx18 *cx, u32 addr);
#endif /* CX18_IO_H */
......@@ -28,6 +28,7 @@
#define SW1_INT_ENABLE_PCI 0xc7311c
#define SW2_INT_SET 0xc73140
#define SW2_INT_STATUS 0xc73144
#define SW2_INT_ENABLE_CPU 0xc73158
#define SW2_INT_ENABLE_PCI 0xc7315c
irqreturn_t cx18_irq_handler(int irq, void *dev_id);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment