drm/bridge: adv7511: add support for the 2nd chip

The Renesas Wheat board has 2 ADV7513 chips on the same I2C bus, however
the ADV751x driver only supports 1 chip as it tries to assign the packet/
EDID/CEC memory I2C devices to the fixed I2C addresses. Assign these I2C
addresses at the fixed offsets (derived from the programming guide) from
the main register map address instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1580212.O1LYdJFM97@wasted.cogentembedded.com

drivers/gpu/drm/bridge/adv7511/adv7511_drv.c

@@ -922,15 +922,13 @@ static int adv7511_parse_dt(struct device_node *np,
 	return 0;
 }
 
-static const int edid_i2c_addr = 0x7e;
-static const int packet_i2c_addr = 0x70;
-static const int cec_i2c_addr = 0x78;
-
 static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
 {
 	struct adv7511_link_config link_config;
 	struct adv7511 *adv7511;
 	struct device *dev = &i2c->dev;
+	unsigned int main_i2c_addr = i2c->addr << 1;
+	unsigned int edid_i2c_addr = main_i2c_addr + 4;
 	unsigned int val;
 	int ret;
 
@@ -991,8 +989,10 @@ static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
 
 	regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR, edid_i2c_addr);
 	regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR,
-		     packet_i2c_addr);
-	regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR, cec_i2c_addr);
+		     main_i2c_addr - 0xa);
+	regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR,
+		     main_i2c_addr - 2);
+
 	adv7511_packet_disable(adv7511, 0xffff);
 
 	adv7511->i2c_main = i2c;

drivers/gpu/drm/bridge/adv7511/adv7533.c

@@ -149,13 +149,12 @@ void adv7533_uninit_cec(struct adv7511 *adv)
 	i2c_unregister_device(adv->i2c_cec);
 }
 
-static const int cec_i2c_addr = 0x78;
-
 int adv7533_init_cec(struct adv7511 *adv)
 {
 	int ret;
 
-	adv->i2c_cec = i2c_new_dummy(adv->i2c_main->adapter, cec_i2c_addr >> 1);
+	adv->i2c_cec = i2c_new_dummy(adv->i2c_main->adapter,
+				     adv->i2c_main->addr - 1);
 	if (!adv->i2c_cec)
 		return -ENOMEM;