Docs/admin: alphabetize some kernel-parameters (part 1)

Move some out-of-place kernel parameters into their correct
locations.

Move one out-of-order keyword/legend in kernel-parameters.rst.

Add some missing keyword legends in kernel-parameters.rst:
  HIBERNATION HYPER_V
and drop some obsolete/removed keyword legends:
 EIDE IOSCHED OSS TS XT

Correct the location of the setup.h file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-doc@vger.kernel.org
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>

Documentation/admin-guide/kernel-parameters.rst

@@ -99,6 +99,7 @@ parameter is applicable::
 	ALSA	ALSA sound support is enabled.
 	APIC	APIC support is enabled.
 	APM	Advanced Power Management support is enabled.
+	APPARMOR AppArmor support is enabled.
 	ARM	ARM architecture is enabled.
 	ARM64	ARM64 architecture is enabled.
 	AX25	Appropriate AX.25 support is enabled.
@@ -108,15 +109,15 @@ parameter is applicable::
 	DYNAMIC_DEBUG Build in debug messages and enable them at runtime
 	EDD	BIOS Enhanced Disk Drive Services (EDD) is enabled
 	EFI	EFI Partitioning (GPT) is enabled
-	EIDE	EIDE/ATAPI support is enabled.
 	EVM	Extended Verification Module
 	FB	The frame buffer device is enabled.
 	FTRACE	Function tracing enabled.
 	GCOV	GCOV profiling is enabled.
+	HIBERNATION HIBERNATION is enabled.
 	HW	Appropriate hardware is enabled.
+	HYPER_V HYPERV support is enabled.
 	IA-64	IA-64 architecture is enabled.
 	IMA     Integrity measurement architecture is enabled.
-	IOSCHED	More than one I/O scheduler is enabled.
 	IP_PNP	IP DHCP, BOOTP, or RARP is enabled.
 	IPV6	IPv6 support is enabled.
 	ISAPNP	ISA PnP code is enabled.
@@ -140,7 +141,6 @@ parameter is applicable::
 	NUMA	NUMA support is enabled.
 	NFS	Appropriate NFS support is enabled.
 	OF	Devicetree is enabled.
-	OSS	OSS sound support is enabled.
 	PV_OPS	A paravirtualized kernel is enabled.
 	PARIDE	The ParIDE (parallel port IDE) subsystem is enabled.
 	PARISC	The PA-RISC architecture is enabled.
@@ -160,7 +160,6 @@ parameter is applicable::
 			the Documentation/scsi/ sub-directory.
 	SECURITY Different security models are enabled.
 	SELINUX SELinux support is enabled.
-	APPARMOR AppArmor support is enabled.
 	SERIAL	Serial support is enabled.
 	SH	SuperH architecture is enabled.
 	SMP	The kernel is an SMP kernel.
@@ -168,7 +167,6 @@ parameter is applicable::
 	SWSUSP	Software suspend (hibernation) is enabled.
 	SUSPEND	System suspend states are enabled.
 	TPM	TPM drivers are enabled.
-	TS	Appropriate touchscreen support is enabled.
 	UMS	USB Mass Storage support is enabled.
 	USB	USB support is enabled.
 	USBHID	USB Human Interface Device support is enabled.
@@ -177,7 +175,6 @@ parameter is applicable::
 	VGA	The VGA console has been enabled.
 	VT	Virtual terminal support is enabled.
 	WDT	Watchdog support is enabled.
-	XT	IBM PC/XT MFM hard disk support is enabled.
 	X86-32	X86-32, aka i386 architecture is enabled.
 	X86-64	X86-64 architecture is enabled.
 			More X86-64 boot options can be found in
@@ -211,7 +208,7 @@ The number of kernel parameters is not limited, but the length of the
 complete command line (parameters including spaces etc.) is limited to
 a fixed number of characters. This limit depends on the architecture
 and is between 256 and 4096 characters. It is defined in the file
-./include/asm/setup.h as COMMAND_LINE_SIZE.
+./include/uapi/asm-generic/setup.h as COMMAND_LINE_SIZE.
 
 Finally, the [KMG] suffix is commonly described after a number of kernel
 parameter values. These 'K', 'M', and 'G' letters represent the _binary_

Documentation/admin-guide/kernel-parameters.txt

@@ -563,6 +563,20 @@
 
 	cio_ignore=	[S390]
 			See Documentation/s390/common_io.rst for details.
+
+	clearcpuid=BITNUM[,BITNUM...] [X86]
+			Disable CPUID feature X for the kernel. See
+			arch/x86/include/asm/cpufeatures.h for the valid bit
+			numbers. Note the Linux specific bits are not necessarily
+			stable over kernel options, but the vendor specific
+			ones should be.
+			Also note that user programs calling CPUID directly
+			or using the feature without checking anything
+			will still see it. This just prevents it from
+			being used by the kernel or shown in /proc/cpuinfo.
+			Also note the kernel might malfunction if you disable
+			some critical bits.
+
 	clk_ignore_unused
 			[CLK]
 			Prevents the clock framework from automatically gating
@@ -631,19 +645,6 @@
 			Defaults to zero when built as a module and to
 			10 seconds when built into the kernel.
 
-	clearcpuid=BITNUM[,BITNUM...] [X86]
-			Disable CPUID feature X for the kernel. See
-			arch/x86/include/asm/cpufeatures.h for the valid bit
-			numbers. Note the Linux specific bits are not necessarily
-			stable over kernel options, but the vendor specific
-			ones should be.
-			Also note that user programs calling CPUID directly
-			or using the feature without checking anything
-			will still see it. This just prevents it from
-			being used by the kernel or shown in /proc/cpuinfo.
-			Also note the kernel might malfunction if you disable
-			some critical bits.
-
 	cma=nn[MG]@[start[MG][-end[MG]]]
 			[KNL,CMA]
 			Sets the size of kernel global memory area for
@@ -950,6 +951,8 @@
 			dump out devices still on the deferred probe list after
 			retrying.
 
+	delayacct	[KNL] Enable per-task delay accounting
+
 	dell_smm_hwmon.ignore_dmi=
 			[HW] Continue probing hardware even if DMI data
 			indicates that the driver is running on unsupported
@@ -1003,17 +1006,6 @@
 	disable=	[IPV6]
 			See Documentation/networking/ipv6.rst.
 
-	hardened_usercopy=
-                        [KNL] Under CONFIG_HARDENED_USERCOPY, whether
-                        hardening is enabled for this boot. Hardened
-                        usercopy checking is used to protect the kernel
-                        from reading or writing beyond known memory
-                        allocation boundaries as a proactive defense
-                        against bounds-checking flaws in the kernel's
-                        copy_to_user()/copy_from_user() interface.
-                on      Perform hardened usercopy checks (default).
-                off     Disable hardened usercopy checks.
-
 	disable_radix	[PPC]
 			Disable RADIX MMU mode on POWER9
 
@@ -1316,17 +1308,6 @@
 			force: enforce the use of EDAC to report H/W event.
 			default: on.
 
-	ekgdboc=	[X86,KGDB] Allow early kernel console debugging
-			ekgdboc=kbd
-
-			This is designed to be used in conjunction with
-			the boot argument: earlyprintk=vga
-
-			This parameter works in place of the kgdboc parameter
-			but can only be used if the backing tty is available
-			very early in the boot process. For early debugging
-			via a serial port see kgdboc_earlycon instead.
-
 	edd=		[EDD]
 			Format: {"off" | "on" | "skip[mbr]"}
 
@@ -1388,6 +1369,17 @@
 	eisa_irq_edge=	[PARISC,HW]
 			See header of drivers/parisc/eisa.c.
 
+	ekgdboc=	[X86,KGDB] Allow early kernel console debugging
+			Format: ekgdboc=kbd
+
+			This is designed to be used in conjunction with
+			the boot argument: earlyprintk=vga
+
+			This parameter works in place of the kgdboc parameter
+			but can only be used if the backing tty is available
+			very early in the boot process. For early debugging
+			via a serial port see kgdboc_earlycon instead.
+
 	elanfreq=	[X86-32]
 			See comment before function elanfreq_setup() in
 			arch/x86/kernel/cpu/cpufreq/elanfreq.c.
@@ -1586,6 +1578,17 @@
 			Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0.
 			Default: 1024
 
+	hardened_usercopy=
+			[KNL] Under CONFIG_HARDENED_USERCOPY, whether
+			hardening is enabled for this boot. Hardened
+			usercopy checking is used to protect the kernel
+			from reading or writing beyond known memory
+			allocation boundaries as a proactive defense
+			against bounds-checking flaws in the kernel's
+			copy_to_user()/copy_from_user() interface.
+		on	Perform hardened usercopy checks (default).
+		off	Disable hardened usercopy checks.
+
 	hardlockup_all_cpu_backtrace=
 			[KNL] Should the hard-lockup detector generate
 			backtraces on all cpus.
@@ -1606,6 +1609,15 @@
 			corresponding firmware-first mode error processing
 			logic will be disabled.
 
+	hibernate=	[HIBERNATION]
+		noresume	Don't check if there's a hibernation image
+				present during boot.
+		nocompress	Don't compress/decompress hibernation images.
+		no		Disable hibernation and resume.
+		protect_image	Turn on image protection during restoration
+				(that will set all pages holding image data
+				during restoration read-only).
+
 	highmem=nn[KMG]	[KNL,BOOT] forces the highmem zone to have an exact
 			size of <nn>. This works even on boxes that have no
 			highmem otherwise. This also works to reduce highmem
@@ -3185,16 +3197,6 @@
 			firmware feature for updating multiple TCE entries
 			at a time.
 
-	onenand.bdry=	[HW,MTD] Flex-OneNAND Boundary Configuration
-
-			Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
-
-			boundary - index of last SLC block on Flex-OneNAND.
-				   The remaining blocks are configured as MLC blocks.
-			lock	 - Configure if Flex-OneNAND boundary should be locked.
-				   Once locked, the boundary cannot be changed.
-				   1 indicates lock status, 0 indicates unlock status.
-
 	mtdset=		[ARM]
 			ARM/S3C2412 JIVE boot control
 
@@ -3441,8 +3443,6 @@
 
 	noclflush	[BUGS=X86] Don't use the CLFLUSH instruction
 
-	delayacct	[KNL] Enable per-task delay accounting
-
 	nodsp		[SH] Disable hardware DSP at boot time.
 
 	noefi		Disable EFI runtime services support.
@@ -3744,6 +3744,16 @@
 			For example, to override I2C bus2:
 			omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
 
+	onenand.bdry=	[HW,MTD] Flex-OneNAND Boundary Configuration
+
+			Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
+
+			boundary - index of last SLC block on Flex-OneNAND.
+				   The remaining blocks are configured as MLC blocks.
+			lock	 - Configure if Flex-OneNAND boundary should be locked.
+				   Once locked, the boundary cannot be changed.
+				   1 indicates lock status, 0 indicates unlock status.
+
 	oops=panic	Always panic on oopses. Default is to just kill the
 			process, but there is a small probability of
 			deadlocking the machine.
@@ -5077,15 +5087,6 @@
 			Useful for devices that are detected asynchronously
 			(e.g. USB and MMC devices).
 
-	hibernate=	[HIBERNATION]
-		noresume	Don't check if there's a hibernation image
-				present during boot.
-		nocompress	Don't compress/decompress hibernation images.
-		no		Disable hibernation and resume.
-		protect_image	Turn on image protection during restoration
-				(that will set all pages holding image data
-				during restoration read-only).
-
 	retain_initrd	[RAM] Keep initrd memory after extraction
 
 	rfkill.default_state=