mmc: sdhci-esdhc-imx: add tuning-step setting support

tuning-step is the delay cell steps in tuning procedure. The default value
of tuning-step is 1. Some boards or cards need another value to pass the
tuning procedure. For example, imx7d-sdb board need the tuning-step value
as 2, otherwise it can't pass the tuning procedure.

So this patch add the tuning-step setting in driver, so that user can set
the tuning-step value in dts.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Acked-by: Dong Aisheng <aisheng.dong@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drivers/mmc/host/sdhci-esdhc-imx.c

@@ -75,6 +75,7 @@
 #define ESDHC_STD_TUNING_EN		(1 << 24)
 /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
 #define ESDHC_TUNING_START_TAP		0x1
+#define ESDHC_TUNING_STEP_SHIFT		16
 
 /* pinctrl state */
 #define ESDHC_PINCTRL_STATE_100MHZ	"state_100mhz"
@@ -474,6 +475,7 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 		} else if (imx_data->socdata->flags & ESDHC_FLAG_STD_TUNING) {
 			u32 v = readl(host->ioaddr + SDHCI_ACMD12_ERR);
 			u32 m = readl(host->ioaddr + ESDHC_MIX_CTRL);
+			u32 tuning_ctrl;
 			if (val & SDHCI_CTRL_TUNED_CLK) {
 				v |= ESDHC_MIX_CTRL_SMPCLK_SEL;
 			} else {
@@ -484,6 +486,11 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
 			if (val & SDHCI_CTRL_EXEC_TUNING) {
 				v |= ESDHC_MIX_CTRL_EXE_TUNE;
 				m |= ESDHC_MIX_CTRL_FBCLK_SEL;
+				tuning_ctrl = readl(host->ioaddr + ESDHC_TUNING_CTRL);
+				tuning_ctrl |= ESDHC_STD_TUNING_EN | ESDHC_TUNING_START_TAP;
+				if (imx_data->boarddata.tuning_step)
+					tuning_ctrl |= imx_data->boarddata.tuning_step << ESDHC_TUNING_STEP_SHIFT;
+					writel(tuning_ctrl, host->ioaddr + ESDHC_TUNING_CTRL);
 			} else {
 				v &= ~ESDHC_MIX_CTRL_EXE_TUNE;
 			}
@@ -963,6 +970,8 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
 	if (gpio_is_valid(boarddata->wp_gpio))
 		boarddata->wp_type = ESDHC_WP_GPIO;
 
+	of_property_read_u32(np, "fsl,tuning-step", &boarddata->tuning_step);
+
 	if (of_find_property(np, "no-1-8-v", NULL))
 		boarddata->support_vsel = false;
 	else

include/linux/platform_data/mmc-esdhc-imx.h

@@ -45,5 +45,6 @@ struct esdhc_platform_data {
 	int max_bus_width;
 	bool support_vsel;
 	unsigned int delay_line;
+	unsigned int tuning_step;       /* The delay cell steps in tuning procedure */
 };
 #endif /* __ASM_ARCH_IMX_ESDHC_H */