arm64: tegra: p2771-0000: Use TEGRA186_ prefix for GPIO names

The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>

arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts

@@ -26,7 +26,8 @@ exp1: gpio@74 {
 			reg = <0x74>;
 
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_MAIN_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
+			interrupts = <TEGRA186_MAIN_GPIO(Y, 0)
+				      GPIO_ACTIVE_LOW>;
 
 			#gpio-cells = <2>;
 			gpio-controller;
@@ -37,7 +38,8 @@ exp2: gpio@77 {
 			reg = <0x77>;
 
 			interrupt-parent = <&gpio>;
-			interrupts = <TEGRA_MAIN_GPIO(Y, 6) GPIO_ACTIVE_LOW>;
+			interrupts = <TEGRA186_MAIN_GPIO(Y, 6)
+				      GPIO_ACTIVE_LOW>;
 
 			#gpio-cells = <2>;
 			gpio-controller;
@@ -108,7 +110,8 @@ sor@15580000 {
 			hdmi-supply = <&vdd_hdmi>;
 
 			nvidia,ddc-i2c-bus = <&ddc>;
-			nvidia,hpd-gpio = <&gpio TEGRA_MAIN_GPIO(P, 1) GPIO_ACTIVE_LOW>;
+			nvidia,hpd-gpio = <&gpio TEGRA186_MAIN_GPIO(P, 1)
+						 GPIO_ACTIVE_LOW>;
 		};
 
 		dpaux@155c0000 {
@@ -121,7 +124,7 @@ gpio-keys {
 
 		power {
 			label = "Power";
-			gpios = <&gpio_aon TEGRA_AON_GPIO(FF, 0)
+			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 0)
 					   GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
 			linux,code = <KEY_POWER>;
@@ -132,7 +135,7 @@ power {
 
 		volume-up {
 			label = "Volume Up";
-			gpios = <&gpio_aon TEGRA_AON_GPIO(FF, 1)
+			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 1)
 					   GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -141,7 +144,7 @@ volume-up {
 
 		volume-down {
 			label = "Volume Down";
-			gpios = <&gpio_aon TEGRA_AON_GPIO(FF, 2)
+			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 2)
 					   GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -158,7 +161,8 @@ vdd_sd: regulator@100 {
 			regulator-min-microvolt = <3300000>;
 			regulator-max-microvolt = <3300000>;
 
-			gpio = <&gpio TEGRA_MAIN_GPIO(P, 6) GPIO_ACTIVE_HIGH>;
+			gpio = <&gpio TEGRA186_MAIN_GPIO(P, 6)
+				      GPIO_ACTIVE_HIGH>;
 			enable-active-high;
 
 			vin-supply = <&vdd_3v3_sys>;