[PATCH] AT91RM9200 Ethernet driver

This patch adds support for the Ethernet controller integrated in the
Atmel AT91RM9200 SoC processor.

Changes since the previous submission (01/02/2006) are:
  - Make use of the clk.h clock infrastructure.
  - The multicast hash function is not crc32. [Patch by Pedro Perez]
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/arm/Kconfig

@@ -31,3 +31,11 @@ config ARM_ETHERH
 	help
 	  If you have an Acorn system with one of these network cards, you
 	  should say Y to this option if you wish to use it with Linux.
+
+config ARM_AT91_ETHER
+	tristate "AT91RM9200 Ethernet support"
+	depends on NET_ETHERNET && ARM && ARCH_AT91RM9200
+	select MII
+	help
+	  If you wish to compile a kernel for the AT91RM9200 and enable
+	  ethernet support, then you should always answer Y to this.

drivers/net/arm/Makefile

@@ -7,3 +7,4 @@ obj-$(CONFIG_ARM_AM79C961A)	+= am79c961a.o
 obj-$(CONFIG_ARM_ETHERH)	+= etherh.o
 obj-$(CONFIG_ARM_ETHER3)	+= ether3.o
 obj-$(CONFIG_ARM_ETHER1)	+= ether1.o
+obj-$(CONFIG_ARM_AT91_ETHER)	+= at91_ether.o

drivers/net/arm/at91_ether.h

+/*
+ * Ethernet driver for the Atmel AT91RM9200 (Thunder)
+ *
+ *  Copyright (C) SAN People (Pty) Ltd
+ *
+ * Based on an earlier Atmel EMAC macrocell driver by Atmel and Lineo Inc.
+ * Initial version by Rick Bronson.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#ifndef AT91_ETHERNET
+#define AT91_ETHERNET
+
+
+/* Davicom 9161 PHY */
+#define MII_DM9161_ID	0x0181b880
+#define MII_DM9161A_ID	0x0181b8a0
+
+/* Davicom specific registers */
+#define MII_DSCR_REG	16
+#define MII_DSCSR_REG	17
+#define MII_DSINTR_REG	21
+
+/* Intel LXT971A PHY */
+#define MII_LXT971A_ID	0x001378E0
+
+/* Intel specific registers */
+#define MII_ISINTE_REG	18
+#define MII_ISINTS_REG	19
+#define MII_LEDCTRL_REG	20
+
+/* Realtek RTL8201 PHY */
+#define MII_RTL8201_ID	0x00008200
+
+/* Broadcom BCM5221 PHY */
+#define MII_BCM5221_ID	0x004061e0
+
+/* Broadcom specific registers */
+#define MII_BCMINTR_REG	26
+
+/* National Semiconductor DP83847 */
+#define MII_DP83847_ID	0x20005c30
+
+/* Altima AC101L PHY */
+#define MII_AC101L_ID	0x00225520
+
+/* Micrel KS8721 PHY */
+#define MII_KS8721_ID	0x00221610
+
+/* ........................................................................ */
+
+#define MAX_RBUFF_SZ	0x600		/* 1518 rounded up */
+#define MAX_RX_DESCR	9		/* max number of receive buffers */
+
+#define EMAC_DESC_DONE	0x00000001	/* bit for if DMA is done */
+#define EMAC_DESC_WRAP	0x00000002	/* bit for wrap */
+
+#define EMAC_BROADCAST	0x80000000	/* broadcast address */
+#define EMAC_MULTICAST	0x40000000	/* multicast address */
+#define EMAC_UNICAST	0x20000000	/* unicast address */
+
+struct rbf_t
+{
+	unsigned int addr;
+	unsigned long size;
+};
+
+struct recv_desc_bufs
+{
+	struct rbf_t descriptors[MAX_RX_DESCR];		/* must be on sizeof (rbf_t) boundary */
+	char recv_buf[MAX_RX_DESCR][MAX_RBUFF_SZ];	/* must be on long boundary */
+};
+
+struct at91_private
+{
+	struct net_device_stats stats;
+	struct mii_if_info mii;			/* ethtool support */
+	struct at91_eth_data board_data;	/* board-specific configuration */
+
+	/* PHY */
+	unsigned long phy_type;			/* type of PHY (PHY_ID) */
+	spinlock_t lock;			/* lock for MDI interface */
+	short phy_media;			/* media interface type */
+	unsigned short phy_address;		/* 5-bit MDI address of PHY (0..31) */
+
+	/* Transmit */
+	struct sk_buff *skb;			/* holds skb until xmit interrupt completes */
+	dma_addr_t skb_physaddr;		/* phys addr from pci_map_single */
+	int skb_length;				/* saved skb length for pci_unmap_single */
+
+	/* Receive */
+	int rxBuffIndex;			/* index into receive descriptor list */
+	struct recv_desc_bufs *dlist;		/* descriptor list address */
+	struct recv_desc_bufs *dlist_phys;	/* descriptor list physical address */
+};
+
+#endif

include/asm-arm/arch-at91rm9200/at91rm9200_emac.h

+/*
+ * include/asm-arm/arch-at91rm9200/at91rm9200_emac.h
+ *
+ * Copyright (C) 2005 Ivan Kokshaysky
+ * Copyright (C) SAN People
+ *
+ * Ethernet MAC registers.
+ * Based on AT91RM9200 datasheet revision E.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef AT91RM9200_EMAC_H
+#define AT91RM9200_EMAC_H
+
+#define	AT91_EMAC_CTL		0x00	/* Control Register */
+#define		AT91_EMAC_LB		(1 <<  0)	/* Loopback */
+#define		AT91_EMAC_LBL		(1 <<  1)	/* Loopback Local */
+#define		AT91_EMAC_RE		(1 <<  2)	/* Receive Enable */
+#define		AT91_EMAC_TE		(1 <<  3)	/* Transmit Enable */
+#define		AT91_EMAC_MPE		(1 <<  4)	/* Management Port Enable */
+#define		AT91_EMAC_CSR		(1 <<  5)	/* Clear Statistics Registers */
+#define		AT91_EMAC_INCSTAT	(1 <<  6)	/* Increment Statistics Registers */
+#define		AT91_EMAC_WES		(1 <<  7)	/* Write Enable for Statistics Registers */
+#define		AT91_EMAC_BP		(1 <<  8)	/* Back Pressure */
+
+#define	AT91_EMAC_CFG		0x04	/* Configuration Register */
+#define		AT91_EMAC_SPD		(1 <<  0)	/* Speed */
+#define		AT91_EMAC_FD		(1 <<  1)	/* Full Duplex */
+#define		AT91_EMAC_BR		(1 <<  2)	/* Bit Rate */
+#define		AT91_EMAC_CAF		(1 <<  4)	/* Copy All Frames */
+#define		AT91_EMAC_NBC		(1 <<  5)	/* No Broadcast */
+#define		AT91_EMAC_MTI		(1 <<  6)	/* Multicast Hash Enable */
+#define		AT91_EMAC_UNI		(1 <<  7)	/* Unicast Hash Enable */
+#define		AT91_EMAC_BIG		(1 <<  8)	/* Receive 1522 Bytes */
+#define		AT91_EMAC_EAE		(1 <<  9)	/* External Address Match Enable */
+#define		AT91_EMAC_CLK		(3 << 10)	/* MDC Clock Divisor */
+#define		AT91_EMAC_CLK_DIV8		(0 << 10)
+#define		AT91_EMAC_CLK_DIV16		(1 << 10)
+#define		AT91_EMAC_CLK_DIV32		(2 << 10)
+#define		AT91_EMAC_CLK_DIV64		(3 << 10)
+#define		AT91_EMAC_RTY		(1 << 12)	/* Retry Test */
+#define		AT91_EMAC_RMII		(1 << 13)	/* Reduce MII (RMII) */
+
+#define	AT91_EMAC_SR		0x08	/* Status Register */
+#define		AT91_EMAC_SR_LINK	(1 <<  0)	/* Link */
+#define		AT91_EMAC_SR_MDIO	(1 <<  1)	/* MDIO pin */
+#define		AT91_EMAC_SR_IDLE	(1 <<  2)	/* PHY idle */
+
+#define	AT91_EMAC_TAR		0x0c	/* Transmit Address Register */
+
+#define	AT91_EMAC_TCR		0x10	/* Transmit Control Register */
+#define		AT91_EMAC_LEN		(0x7ff << 0)	/* Transmit Frame Length */
+#define		AT91_EMAC_NCRC		(1     << 15)	/* No CRC */
+
+#define	AT91_EMAC_TSR		0x14	/* Transmit Status Register */
+#define		AT91_EMAC_TSR_OVR	(1 <<  0)	/* Transmit Buffer Overrun */
+#define		AT91_EMAC_TSR_COL	(1 <<  1)	/* Collision Occurred */
+#define		AT91_EMAC_TSR_RLE	(1 <<  2)	/* Retry Limit Exceeded */
+#define		AT91_EMAC_TSR_IDLE	(1 <<  3)	/* Transmitter Idle */
+#define		AT91_EMAC_TSR_BNQ	(1 <<  4)	/* Transmit Buffer not Queued */
+#define		AT91_EMAC_TSR_COMP	(1 <<  5)	/* Transmit Complete */
+#define		AT91_EMAC_TSR_UND	(1 <<  6)	/* Transmit Underrun */
+
+#define	AT91_EMAC_RBQP		0x18	/* Receive Buffer Queue Pointer */
+
+#define	AT91_EMAC_RSR		0x20	/* Receive Status Register */
+#define		AT91_EMAC_RSR_BNA	(1 <<  0)	/* Buffer Not Available */
+#define		AT91_EMAC_RSR_REC	(1 <<  1)	/* Frame Received */
+#define		AT91_EMAC_RSR_OVR	(1 <<  2)	/* RX Overrun */
+
+#define	AT91_EMAC_ISR		0x24	/* Interrupt Status Register */
+#define		AT91_EMAC_DONE		(1 <<  0)	/* Management Done */
+#define		AT91_EMAC_RCOM		(1 <<  1)	/* Receive Complete */
+#define		AT91_EMAC_RBNA		(1 <<  2)	/* Receive Buffer Not Available */
+#define		AT91_EMAC_TOVR		(1 <<  3)	/* Transmit Buffer Overrun */
+#define		AT91_EMAC_TUND		(1 <<  4)	/* Transmit Buffer Underrun */
+#define		AT91_EMAC_RTRY		(1 <<  5)	/* Retry Limit */
+#define		AT91_EMAC_TBRE		(1 <<  6)	/* Transmit Buffer Register Empty */
+#define		AT91_EMAC_TCOM		(1 <<  7)	/* Transmit Complete */
+#define		AT91_EMAC_TIDLE		(1 <<  8)	/* Transmit Idle */
+#define		AT91_EMAC_LINK		(1 <<  9)	/* Link */
+#define		AT91_EMAC_ROVR		(1 << 10)	/* RX Overrun */
+#define		AT91_EMAC_ABT		(1 << 11)	/* Abort */
+
+#define	AT91_EMAC_IER		0x28	/* Interrupt Enable Register */
+#define	AT91_EMAC_IDR		0x2c	/* Interrupt Disable Register */
+#define	AT91_EMAC_IMR		0x30	/* Interrupt Mask Register */
+
+#define	AT91_EMAC_MAN		0x34	/* PHY Maintenance Register */
+#define		AT91_EMAC_DATA		(0xffff << 0)	/* MDIO Data */
+#define		AT91_EMAC_REGA		(0x1f	<< 18)	/* MDIO Register */
+#define		AT91_EMAC_PHYA		(0x1f	<< 23)	/* MDIO PHY Address */
+#define		AT91_EMAC_RW		(3	<< 28)	/* Read/Write operation */
+#define			AT91_EMAC_RW_W		(1 << 28)
+#define			AT91_EMAC_RW_R		(2 << 28)
+#define		AT91_EMAC_MAN_802_3	0x40020000	/* IEEE 802.3 value */
+
+/*
+ * Statistics Registers.
+ */
+#define AT91_EMAC_FRA		0x40	/* Frames Transmitted OK */
+#define AT91_EMAC_SCOL		0x44	/* Single Collision Frame */
+#define AT91_EMAC_MCOL		0x48	/* Multiple Collision Frame */
+#define AT91_EMAC_OK		0x4c	/* Frames Received OK */
+#define AT91_EMAC_SEQE		0x50	/* Frame Check Sequence Error */
+#define AT91_EMAC_ALE		0x54	/* Alignmemt Error */
+#define AT91_EMAC_DTE		0x58	/* Deffered Transmission Frame */
+#define AT91_EMAC_LCOL		0x5c	/* Late Collision */
+#define AT91_EMAC_ECOL		0x60	/* Excessive Collision */
+#define AT91_EMAC_TUE		0x64	/* Transmit Underrun Error */
+#define AT91_EMAC_CSE		0x68	/* Carrier Sense Error */
+#define AT91_EMAC_DRFC		0x6c	/* Discard RX Frame */
+#define AT91_EMAC_ROV		0x70	/* Receive Overrun */
+#define AT91_EMAC_CDE		0x74	/* Code Error */
+#define AT91_EMAC_ELR		0x78	/* Excessive Length Error */
+#define AT91_EMAC_RJB		0x7c	/* Receive Jabber */
+#define AT91_EMAC_USF		0x80	/* Undersize Frame */
+#define AT91_EMAC_SQEE		0x84	/* SQE Test Error */
+
+/*
+ * Address Registers.
+ */
+#define AT91_EMAC_HSL		0x90	/* Hash Address Low [31:0] */
+#define AT91_EMAC_HSH		0x94	/* Hash Address High [63:32] */
+#define AT91_EMAC_SA1L		0x98	/* Specific Address 1 Low, bytes 0-3 */
+#define AT91_EMAC_SA1H		0x9c	/* Specific Address 1 High, bytes 4-5 */
+#define AT91_EMAC_SA2L		0xa0	/* Specific Address 2 Low, bytes 0-3 */
+#define AT91_EMAC_SA2H		0xa4	/* Specific Address 2 High, bytes 4-5 */
+#define AT91_EMAC_SA3L		0xa8	/* Specific Address 3 Low, bytes 0-3 */
+#define AT91_EMAC_SA3H		0xac	/* Specific Address 3 High, bytes 4-5 */
+#define AT91_EMAC_SA4L		0xb0	/* Specific Address 4 Low, bytes 0-3 */
+#define AT91_EMAC_SA4H		0xb4	/* Specific Address 4 High, bytes 4-5 */
+
+#endif