USB: Consolidate LPM checks to avoid enabling LPM twice

USB Bluetooth controller QCA ROME (0cf3:e007) sometimes stops working
after S3:
[ 165.110742] Bluetooth: hci0: using NVM file: qca/nvm_usb_00000302.bin
[ 168.432065] Bluetooth: hci0: Failed to send body at 4 of 1953 (-110)

After some experiments, I found that disabling LPM can workaround the
issue.

On some platforms, the USB power is cut during S3, so the driver uses
reset-resume to resume the device. During port resume, LPM gets enabled
twice, by usb_reset_and_verify_device() and usb_port_resume().

Consolidate all checks into new LPM helpers to make sure LPM only gets
enabled once.

Fixes: de68bab4 ("usb: Don't enable USB 2.0 Link PM by default.”)
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org> # after much soaking
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/core/driver.c

@@ -1901,9 +1901,6 @@ static int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
 	struct usb_hcd *hcd = bus_to_hcd(udev->bus);
 	int ret = -EPERM;
 
-	if (enable && !udev->usb2_hw_lpm_allowed)
-		return 0;
-
 	if (hcd->driver->set_usb2_hw_lpm) {
 		ret = hcd->driver->set_usb2_hw_lpm(hcd, udev, enable);
 		if (!ret)
@@ -1915,11 +1912,19 @@ static int usb_set_usb2_hardware_lpm(struct usb_device *udev, int enable)
 
 int usb_enable_usb2_hardware_lpm(struct usb_device *udev)
 {
+	if (!udev->usb2_hw_lpm_capable ||
+	    !udev->usb2_hw_lpm_allowed ||
+	    udev->usb2_hw_lpm_enabled)
+		return 0;
+
 	return usb_set_usb2_hardware_lpm(udev, 1);
 }
 
 int usb_disable_usb2_hardware_lpm(struct usb_device *udev)
 {
+	if (!udev->usb2_hw_lpm_enabled)
+		return 0;
+
 	return usb_set_usb2_hardware_lpm(udev, 0);
 }
 

drivers/usb/core/hub.c

@@ -3251,8 +3251,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
 	}
 
 	/* disable USB2 hardware LPM */
-	if (udev->usb2_hw_lpm_enabled == 1)
-		usb_disable_usb2_hardware_lpm(udev);
+	usb_disable_usb2_hardware_lpm(udev);
 
 	if (usb_disable_ltm(udev)) {
 		dev_err(&udev->dev, "Failed to disable LTM before suspend\n");
@@ -3290,8 +3289,7 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
 		usb_enable_ltm(udev);
  err_ltm:
 		/* Try to enable USB2 hardware LPM again */
-		if (udev->usb2_hw_lpm_capable == 1)
-			usb_enable_usb2_hardware_lpm(udev);
+		usb_enable_usb2_hardware_lpm(udev);
 
 		if (udev->do_remote_wakeup)
 			(void) usb_disable_remote_wakeup(udev);
@@ -3574,8 +3572,7 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg)
 		hub_port_logical_disconnect(hub, port1);
 	} else  {
 		/* Try to enable USB2 hardware LPM */
-		if (udev->usb2_hw_lpm_capable == 1)
-			usb_enable_usb2_hardware_lpm(udev);
+		usb_enable_usb2_hardware_lpm(udev);
 
 		/* Try to enable USB3 LTM */
 		usb_enable_ltm(udev);
@@ -5680,8 +5677,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev)
 	/* Disable USB2 hardware LPM.
 	 * It will be re-enabled by the enumeration process.
 	 */
-	if (udev->usb2_hw_lpm_enabled == 1)
-		usb_disable_usb2_hardware_lpm(udev);
+	usb_disable_usb2_hardware_lpm(udev);
 
 	/* Disable LPM while we reset the device and reinstall the alt settings.
 	 * Device-initiated LPM, and system exit latency settings are cleared

drivers/usb/core/message.c

@@ -1243,8 +1243,7 @@ void usb_disable_device(struct usb_device *dev, int skip_ep0)
 			dev->actconfig->interface[i] = NULL;
 		}
 
-		if (dev->usb2_hw_lpm_enabled == 1)
-			usb_disable_usb2_hardware_lpm(dev);
+		usb_disable_usb2_hardware_lpm(dev);
 		usb_unlocked_disable_lpm(dev);
 		usb_disable_ltm(dev);