Commit d8323c6b authored by Maxime Ripard's avatar Maxime Ripard Committed by Linus Walleij

pinctrl: sunxi: Add custom irq_domain_ops

The current interrupt parsing code was working by accident, because the
default was actually parsing the first node of interrupts.

While that was mostly working (and the flags were actually ignored), this
binding has never been documented, and doesn't work with SoCs that have
multiple interrupt banks anyway.

Add a proper interrupt xlate function, that uses the same description than
the GPIOs (<bank> <pin> <flags>), that will make things less confusing.

The EINT number will still be used as the hwirq number, but won't be
exposed through the DT.
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: default avatarHans de Goede <hdegoede@redhat.com>
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
parent e3249570
...@@ -48,7 +48,7 @@ Optional subnode-properties: ...@@ -48,7 +48,7 @@ Optional subnode-properties:
Examples: Examples:
pinctrl@01c20800 { pio: pinctrl@01c20800 {
compatible = "allwinner,sun5i-a13-pinctrl"; compatible = "allwinner,sun5i-a13-pinctrl";
reg = <0x01c20800 0x400>; reg = <0x01c20800 0x400>;
#address-cells = <1>; #address-cells = <1>;
...@@ -68,3 +68,38 @@ pinctrl@01c20800 { ...@@ -68,3 +68,38 @@ pinctrl@01c20800 {
allwinner,pull = <0>; allwinner,pull = <0>;
}; };
}; };
GPIO and interrupt controller
-----------------------------
This hardware also acts as a GPIO controller and an interrupt
controller.
Consumers that would want to refer to one or the other (or both)
should provide through the usual *-gpios and interrupts properties a
cell with 3 arguments, first the number of the bank, then the pin
inside that bank, and finally the flags for the GPIO/interrupts.
Example:
xio: gpio@38 {
compatible = "nxp,pcf8574a";
reg = <0x38>;
gpio-controller;
#gpio-cells = <2>;
interrupt-parent = <&pio>;
interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>;
interrupt-controller;
#interrupt-cells = <2>;
};
reg_usb1_vbus: usb1-vbus {
compatible = "regulator-fixed";
regulator-name = "usb1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>;
};
...@@ -711,6 +711,37 @@ static struct irq_chip sunxi_pinctrl_level_irq_chip = { ...@@ -711,6 +711,37 @@ static struct irq_chip sunxi_pinctrl_level_irq_chip = {
IRQCHIP_EOI_IF_HANDLED, IRQCHIP_EOI_IF_HANDLED,
}; };
static int sunxi_pinctrl_irq_of_xlate(struct irq_domain *d,
struct device_node *node,
const u32 *intspec,
unsigned int intsize,
unsigned long *out_hwirq,
unsigned int *out_type)
{
struct sunxi_desc_function *desc;
int pin, base;
if (intsize < 3)
return -EINVAL;
base = PINS_PER_BANK * intspec[0];
pin = base + intspec[1];
desc = sunxi_pinctrl_desc_find_function_by_pin(d->host_data,
pin, "irq");
if (!desc)
return -EINVAL;
*out_hwirq = desc->irqbank * PINS_PER_BANK + desc->irqnum;
*out_type = intspec[2];
return 0;
}
static struct irq_domain_ops sunxi_pinctrl_irq_domain_ops = {
.xlate = sunxi_pinctrl_irq_of_xlate,
};
static void sunxi_pinctrl_irq_handler(unsigned __irq, struct irq_desc *desc) static void sunxi_pinctrl_irq_handler(unsigned __irq, struct irq_desc *desc)
{ {
unsigned int irq = irq_desc_get_irq(desc); unsigned int irq = irq_desc_get_irq(desc);
...@@ -986,8 +1017,8 @@ int sunxi_pinctrl_init(struct platform_device *pdev, ...@@ -986,8 +1017,8 @@ int sunxi_pinctrl_init(struct platform_device *pdev,
pctl->domain = irq_domain_add_linear(node, pctl->domain = irq_domain_add_linear(node,
pctl->desc->irq_banks * IRQ_PER_BANK, pctl->desc->irq_banks * IRQ_PER_BANK,
&irq_domain_simple_ops, &sunxi_pinctrl_irq_domain_ops,
NULL); pctl);
if (!pctl->domain) { if (!pctl->domain) {
dev_err(&pdev->dev, "Couldn't register IRQ domain\n"); dev_err(&pdev->dev, "Couldn't register IRQ domain\n");
ret = -ENOMEM; ret = -ENOMEM;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment