Commit d8a44fe7 authored by Punit Agrawal's avatar Punit Agrawal Committed by Sudeep Holla

Documentation: add DT bindings for ARM SCPI sensors

The System Control Processor (SCP) provides access to SoC sensors via
the System Control and Power Interface (SCPI) Message Protocol. Add
bindings to allow probing of these sensors. Also support referencing
of the sensors for setting up thermal zones via the thermal DT
bindings.
Signed-off-by: default avatarPunit Agrawal <punit.agrawal@arm.com>
Acked-by: default avatarRob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
parent 8def3103
......@@ -72,8 +72,25 @@ Required sub-node properties:
- compatible : should be "arm,juno-scp-shmem" for Non-secure SRAM based
shared memory on Juno platforms
Sensor bindings for the sensors based on SCPI Message Protocol
--------------------------------------------------------------
SCPI provides an API to access the various sensors on the SoC.
Required properties:
- compatible : should be "arm,scpi-sensors".
- #thermal-sensor-cells: should be set to 1. This property follows the
thermal device tree bindings[2].
Valid cell values are raw identifiers (Sensor
ID) as used by the firmware. Refer to
platform documentation for your
implementation for the IDs to use. For Juno
R0 and Juno R1 refer to [3].
[0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/thermal/thermal.txt
[3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html
Example:
......@@ -122,6 +139,11 @@ scpi_protocol: scpi@2e000000 {
clock-output-names = "pxlclk0", "pxlclk1";
};
};
scpi_sensors0: sensors {
compatible = "arm,scpi-sensors";
#thermal-sensor-cells = <1>;
};
};
cpu@0 {
......@@ -136,6 +158,17 @@ hdlcd@7ff60000 {
clocks = <&scpi_clk 4>;
};
thermal-zones {
soc_thermal {
polling-delay-passive = <100>;
polling-delay = <1000>;
/* sensor ID */
thermal-sensors = <&scpi_sensors0 3>;
...
};
};
In the above example, the #clock-cells is set to 1 as required.
scpi_dvfs has 3 output clocks namely: atlclk, aplclk, and gpuclk with 0,
1 and 2 as clock-indices. scpi_clk has 2 output clocks namely: pxlclk0
......@@ -148,3 +181,8 @@ scpi_dvfs i.e. "atlclk".
Similarly the second example is hdlcd@7ff60000 and it has pxlclk1 as input
clock. '4' in the clock specifier here points to the second entry
in the output clocks of scpi_clocks i.e. "pxlclk1"
The thermal-sensors property in the soc_thermal node uses the
temperature sensor provided by SCP firmware to setup a thermal
zone. The ID "3" is the sensor identifier for the temperature sensor
as used by the firmware.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment