Commit d980b8d1 authored by David S. Miller's avatar David S. Miller

Merge branch 'MDIO-bus-reset-GPIO-cleanups'

Sergei Shtylyov says:

====================
MDIO bus reset GPIO cleanups

Commit 4c5e7a2c ("dt-bindings: mdio: Clarify binding document")
declared that a MDIO reset GPIO property should have only a single GPIO
reference/specifier, however the supporting code was left intact...
Here's a couple of the obvious cleanups to that code:

[1/2] mdio_bus: handle only single PHY reset GPIO
[2/2] mdio_bus: use devm_gpiod_get_optional()
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 61d3e1d9 fe0e4052
......@@ -353,33 +353,18 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
mutex_init(&bus->mdio_lock);
/* de-assert bus level PHY GPIO resets */
if (bus->num_reset_gpios > 0) {
bus->reset_gpiod = devm_kcalloc(&bus->dev,
bus->num_reset_gpios,
sizeof(struct gpio_desc *),
GFP_KERNEL);
if (!bus->reset_gpiod)
return -ENOMEM;
}
for (i = 0; i < bus->num_reset_gpios; i++) {
gpiod = devm_gpiod_get_index(&bus->dev, "reset", i,
GPIOD_OUT_LOW);
if (IS_ERR(gpiod)) {
err = PTR_ERR(gpiod);
if (err != -ENOENT) {
dev_err(&bus->dev,
"mii_bus %s couldn't get reset GPIO\n",
bus->id);
return err;
}
} else {
bus->reset_gpiod[i] = gpiod;
gpiod_set_value_cansleep(gpiod, 1);
udelay(bus->reset_delay_us);
gpiod_set_value_cansleep(gpiod, 0);
}
/* de-assert bus level PHY GPIO reset */
gpiod = devm_gpiod_get_optional(&bus->dev, "reset", GPIOD_OUT_LOW);
if (IS_ERR(gpiod)) {
dev_err(&bus->dev, "mii_bus %s couldn't get reset GPIO\n",
bus->id);
return PTR_ERR(gpiod);
} else if (gpiod) {
bus->reset_gpiod = gpiod;
gpiod_set_value_cansleep(gpiod, 1);
udelay(bus->reset_delay_us);
gpiod_set_value_cansleep(gpiod, 0);
}
if (bus->reset)
......@@ -414,10 +399,8 @@ int __mdiobus_register(struct mii_bus *bus, struct module *owner)
}
/* Put PHYs in RESET to save power */
for (i = 0; i < bus->num_reset_gpios; i++) {
if (bus->reset_gpiod[i])
gpiod_set_value_cansleep(bus->reset_gpiod[i], 1);
}
if (bus->reset_gpiod)
gpiod_set_value_cansleep(bus->reset_gpiod, 1);
device_del(&bus->dev);
return err;
......@@ -442,10 +425,8 @@ void mdiobus_unregister(struct mii_bus *bus)
}
/* Put PHYs in RESET to save power */
for (i = 0; i < bus->num_reset_gpios; i++) {
if (bus->reset_gpiod[i])
gpiod_set_value_cansleep(bus->reset_gpiod[i], 1);
}
if (bus->reset_gpiod)
gpiod_set_value_cansleep(bus->reset_gpiod, 1);
device_del(&bus->dev);
}
......
......@@ -226,7 +226,6 @@ int of_mdiobus_register(struct mii_bus *mdio, struct device_node *np)
/* Get bus level PHY reset GPIO details */
mdio->reset_delay_us = DEFAULT_GPIO_RESET_DELAY;
of_property_read_u32(np, "reset-delay-us", &mdio->reset_delay_us);
mdio->num_reset_gpios = of_gpio_named_count(np, "reset-gpios");
/* Register the MDIO bus */
rc = mdiobus_register(mdio);
......
......@@ -226,10 +226,8 @@ struct mii_bus {
/* GPIO reset pulse width in microseconds */
int reset_delay_us;
/* Number of reset GPIOs */
int num_reset_gpios;
/* Array of RESET GPIO descriptors */
struct gpio_desc **reset_gpiod;
/* RESET GPIO descriptor pointer */
struct gpio_desc *reset_gpiod;
};
#define to_mii_bus(d) container_of(d, struct mii_bus, dev)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment