Merge tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB / PHY updates from Greg KH:
 "Here are the big set of USB and PHY driver patches for 5.7-rc1.

  Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
  updates, xhci updates, usb-serial driver updates and new device ids,
  and other minor things. Full details in the shortlog.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
  USB: cdc-acm: restore capability check order
  usb: cdns3: make signed 1 bit bitfields unsigned
  usb: gadget: fsl: remove unused variable 'driver_desc'
  usb: gadget: f_fs: Fix use after free issue as part of queue failure
  usb: typec: Correct the documentation for typec_cable_put()
  USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
  USB: serial: option: add Wistron Neweb D19Q1
  USB: serial: option: add BroadMobi BM806U
  USB: serial: option: add support for ASKEY WWHC050
  usb: core: Add ACPI support for USB interface devices
  driver core: platform: Reimplement devm_platform_ioremap_resource
  usb: dwc2: convert to devm_platform_get_and_ioremap_resource
  usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
  usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
  drivers: provide devm_platform_get_and_ioremap_resource()
  phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
  phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
  dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
  phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
  dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
  ...

Documentation/ABI/testing/sysfs-class-typec

@@ -20,13 +20,13 @@ Date:		April 2017
 Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
 Description:
 		The supported power roles. This attribute can be used to request
-		power role swap on the port when the port supports USB Power
-		Delivery. Swapping is supported as synchronous operation, so
-		write(2) to the attribute will not return until the operation
-		has finished. The attribute is notified about role changes so
-		that poll(2) on the attribute wakes up. Change on the role will
-		also generate uevent KOBJ_CHANGE. The current role is show in
-		brackets, for example "[source] sink" when in source mode.
+		power role swap on the port. Swapping is supported as
+		synchronous operation, so write(2) to the attribute will not
+		return until the operation has finished. The attribute is
+		notified about role changes so that poll(2) on the attribute
+		wakes up. Change on the role will also generate uevent
+		KOBJ_CHANGE. The current role is show in brackets, for example
+		"[source] sink" when in source mode.
 
 		Valid values: source, sink
 
@@ -108,6 +108,15 @@ Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
 Description:
 		Revision number of the supported USB Type-C specification.
 
+What:		/sys/class/typec/<port>/orientation
+Date:		February 2020
+Contact:	Badhri Jagan Sridharan <badhri@google.com>
+Description:
+		Indicates the active orientation of the Type-C connector.
+		Valid values:
+		- "normal": CC1 orientation
+		- "reverse": CC2 orientation
+		- "unknown": Orientation cannot be determined.
 
 USB Type-C partner devices (eg. /sys/class/typec/port0-partner/)
 

Documentation/devicetree/bindings/phy/amlogic,meson-g12a-usb2-phy.yaml

@@ -14,6 +14,7 @@ properties:
   compatible:
     enum:
       - amlogic,meson-g12a-usb2-phy
+      - amlogic,meson-a1-usb2-phy
 
   reg:
     maxItems: 1
@@ -49,6 +50,19 @@ required:
   - reset-names
   - "#phy-cells"
 
+if:
+  properties:
+    compatible:
+      enum:
+        - amlogic,meson-a1-usb-ctrl
+
+then:
+  properties:
+    power-domains:
+      maxItems: 1
+  required:
+    - power-domains
+
 examples:
   - |
     phy@36000 {

Documentation/devicetree/bindings/phy/phy-cadence-dp.txt

-Cadence MHDP DisplayPort SD0801 PHY binding
-===========================================
-
-This binding describes the Cadence SD0801 PHY hardware included with
-the Cadence MHDP DisplayPort controller.
-
--------------------------------------------------------------------------------
-Required properties (controller (parent) node):
-- compatible	: Should be "cdns,dp-phy"
-- reg		: Defines the following sets of registers in the parent
-		  mhdp device:
-			- Offset of the DPTX PHY configuration registers
-			- Offset of the SD0801 PHY configuration registers
-- #phy-cells	: from the generic PHY bindings, must be 0.
-
-Optional properties:
-- num_lanes	: Number of DisplayPort lanes to use (1, 2 or 4)
-- max_bit_rate	: Maximum DisplayPort link bit rate to use, in Mbps (2160,
-		  2430, 2700, 3240, 4320, 5400 or 8100)
--------------------------------------------------------------------------------
-
-Example:
-	dp_phy: phy@f0fb030a00 {
-		compatible = "cdns,dp-phy";
-		reg = <0xf0 0xfb030a00 0x0 0x00000040>,
-		      <0xf0 0xfb500000 0x0 0x00100000>;
-		num_lanes = <4>;
-		max_bit_rate = <8100>;
-		#phy-cells = <0>;
-	};

Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/phy-cadence-torrent.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Cadence Torrent SD0801 PHY binding for DisplayPort
+
+description:
+  This binding describes the Cadence SD0801 PHY (also known as Torrent PHY)
+  hardware included with the Cadence MHDP DisplayPort controller.
+
+maintainers:
+  - Swapnil Jakhade <sjakhade@cadence.com>
+  - Yuti Amonkar <yamonkar@cadence.com>
+
+properties:
+  compatible:
+    enum:
+      - cdns,torrent-phy
+      - ti,j721e-serdes-10g
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  clocks:
+    maxItems: 1
+    description:
+      PHY reference clock. Must contain an entry in clock-names.
+
+  clock-names:
+    const: refclk
+
+  reg:
+    minItems: 1
+    maxItems: 2
+    items:
+      - description: Offset of the Torrent PHY configuration registers.
+      - description: Offset of the DPTX PHY configuration registers.
+
+  reg-names:
+    minItems: 1
+    maxItems: 2
+    items:
+      - const: torrent_phy
+      - const: dptx_phy
+
+  resets:
+    maxItems: 1
+    description:
+      Torrent PHY reset.
+      See Documentation/devicetree/bindings/reset/reset.txt
+
+patternProperties:
+  '^phy@[0-7]+$':
+    type: object
+    description:
+      Each group of PHY lanes with a single master lane should be represented as a sub-node.
+    properties:
+      reg:
+        description:
+          The master lane number. This is the lowest numbered lane in the lane group.
+
+      resets:
+        minItems: 1
+        maxItems: 4
+        description:
+          Contains list of resets, one per lane, to get all the link lanes out of reset.
+
+      "#phy-cells":
+        const: 0
+
+      cdns,phy-type:
+        description:
+          Specifies the type of PHY for which the group of PHY lanes is used.
+          Refer include/dt-bindings/phy/phy.h. Constants from the header should be used.
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [1, 2, 3, 4, 5, 6]
+
+      cdns,num-lanes:
+        description:
+          Number of DisplayPort lanes.
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [1, 2, 4]
+        default: 4
+
+      cdns,max-bit-rate:
+        description:
+          Maximum DisplayPort link bit rate to use, in Mbps
+        allOf:
+          - $ref: /schemas/types.yaml#/definitions/uint32
+          - enum: [2160, 2430, 2700, 3240, 4320, 5400, 8100]
+        default: 8100
+
+    required:
+      - reg
+      - resets
+      - "#phy-cells"
+      - cdns,phy-type
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - "#address-cells"
+  - "#size-cells"
+  - clocks
+  - clock-names
+  - reg
+  - reg-names
+  - resets
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/phy/phy.h>
+    torrent_phy: torrent-phy@f0fb500000 {
+          compatible = "cdns,torrent-phy";
+          reg = <0xf0 0xfb500000 0x0 0x00100000>,
+                <0xf0 0xfb030a00 0x0 0x00000040>;
+          reg-names = "torrent_phy", "dptx_phy";
+          resets = <&phyrst 0>;
+          clocks = <&ref_clk>;
+          clock-names = "refclk";
+          #address-cells = <1>;
+          #size-cells = <0>;
+          torrent_phy_dp: phy@0 {
+                    reg = <0>;
+                    resets = <&phyrst 1>, <&phyrst 2>,
+                             <&phyrst 3>, <&phyrst 4>;
+                    #phy-cells = <0>;
+                    cdns,phy-type = <PHY_TYPE_DP>;
+                    cdns,num-lanes = <4>;
+                    cdns,max-bit-rate = <8100>;
+          };
+    };
+...

Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt

@@ -13,10 +13,16 @@ Required properties (controller (parent) node):
 		  "mediatek,mt8173-u3phy";
 		  make use of "mediatek,generic-tphy-v1" on mt2701 instead and
 		  "mediatek,generic-tphy-v2" on mt2712 instead.
- - clocks	: (deprecated, use port's clocks instead) a list of phandle +
-		  clock-specifier pairs, one for each entry in clock-names
- - clock-names	: (deprecated, use port's one instead) must contain
-		  "u3phya_ref": for reference clock of usb3.0 analog phy.
+
+- #address-cells:	the number of cells used to represent physical
+		base addresses.
+- #size-cells:	the number of cells used to represent the size of an address.
+- ranges:	the address mapping relationship to the parent, defined with
+		- empty value: if optional 'reg' is used.
+		- non-empty value: if optional 'reg' is not used. should set
+			the child's base address to 0, the physical address
+			within parent's address space, and the length of
+			the address map.
 
 Required nodes	: a sub-node is required for each port the controller
 		  provides. Address range information including the usual
@@ -34,12 +40,6 @@ Optional properties (controller (parent) node):
 
 Required properties (port (child) node):
 - reg		: address and length of the register set for the port.
-- clocks	: a list of phandle + clock-specifier pairs, one for each
-		  entry in clock-names
-- clock-names	: must contain
-		  "ref": 48M reference clock for HighSpeed analog phy; and 26M
-			reference clock for SuperSpeed analog phy, sometimes is
-			24M, 25M or 27M, depended on platform.
 - #phy-cells	: should be 1 (See second example)
 		  cell after port phandle is phy type from:
 			- PHY_TYPE_USB2
@@ -48,10 +48,22 @@ Required properties (port (child) node):
 			- PHY_TYPE_SATA
 
 Optional properties (PHY_TYPE_USB2 port (child) node):
+- clocks	: a list of phandle + clock-specifier pairs, one for each
+		  entry in clock-names
+- clock-names	: may contain
+		  "ref": 48M reference clock for HighSpeed (digital) phy; and 26M
+			reference clock for SuperSpeed (digital) phy, sometimes is
+			24M, 25M or 27M, depended on platform.
+		  "da_ref": the reference clock of analog phy, used if the clocks
+			of analog and digital phys are separated, otherwise uses
+			"ref" clock only if needed.
+
 - mediatek,eye-src	: u32, the value of slew rate calibrate
 - mediatek,eye-vrt	: u32, the selection of VRT reference voltage
 - mediatek,eye-term	: u32, the selection of HS_TX TERM reference voltage
 - mediatek,bc12	: bool, enable BC12 of u2phy if support it
+- mediatek,discth	: u32, the selection of disconnect threshold
+- mediatek,intr	: u32, the selection of internal R (resistance)
 
 Example:
 

Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,qusb2-phy.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm QUSB2 phy controller
+
+maintainers:
+  - Manu Gautam <mgautam@codeaurora.org>
+
+description:
+  QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+        - enum:
+          - qcom,msm8996-qusb2-phy
+          - qcom,msm8998-qusb2-phy
+      - items:
+        - enum:
+          - qcom,sc7180-qusb2-phy
+          - qcom,sdm845-qusb2-phy
+        - const: qcom,qusb2-v2-phy
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  clocks:
+    minItems: 2
+    maxItems: 3
+    items:
+      - description: phy config clock
+      - description: 19.2 MHz ref clk
+      - description: phy interface clock (Optional)
+
+  clock-names:
+    minItems: 2
+    maxItems: 3
+    items:
+      - const: cfg_ahb
+      - const: ref
+      - const: iface
+
+  vdda-pll-supply:
+     description:
+       Phandle to 1.8V regulator supply to PHY refclk pll block.
+
+  vdda-phy-dpdm-supply:
+     description:
+       Phandle to 3.1V regulator supply to Dp/Dm port signals.
+
+  resets:
+    maxItems: 1
+    description:
+      Phandle to reset to phy block.
+
+  nvmem-cells:
+    maxItems: 1
+    description:
+        Phandle to nvmem cell that contains 'HS Tx trim'
+        tuning parameter value for qusb2 phy.
+
+  qcom,tcsr-syscon:
+    description:
+        Phandle to TCSR syscon register region.
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: qcom,qusb2-v2-phy
+then:
+  properties:
+    qcom,imp-res-offset-value:
+      description:
+        It is a 6 bit value that specifies offset to be
+        added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
+        tuning parameter that may vary for different boards of same SOC.
+      allOf:
+        - $ref: /schemas/types.yaml#/definitions/uint32
+        - minimum: 0
+          maximum: 63
+          default: 0
+
+    qcom,bias-ctrl-value:
+      description:
+        It is a 6 bit value that specifies bias-ctrl-value. It is a PHY
+        tuning parameter that may vary for different boards of same SOC.
+      allOf:
+        - $ref: /schemas/types.yaml#/definitions/uint32
+        - minimum: 0
+          maximum: 63
+          default: 0
+
+    qcom,charge-ctrl-value:
+     description:
+        It is a 2 bit value that specifies charge-ctrl-value. It is a PHY
+        tuning parameter that may vary for different boards of same SOC.
+     allOf:
+       - $ref: /schemas/types.yaml#/definitions/uint32
+       - minimum: 0
+         maximum: 3
+         default: 0
+
+    qcom,hstx-trim-value:
+      description:
+        It is a 4 bit value that specifies tuning for HSTX
+        output current.
+        Possible range is - 15mA to 24mA (stepsize of 600 uA).
+        See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+      allOf:
+        - $ref: /schemas/types.yaml#/definitions/uint32
+        - minimum: 0
+          maximum: 15
+          default: 3
+
+    qcom,preemphasis-level:
+      description:
+        It is a 2 bit value that specifies pre-emphasis level.
+        Possible range is 0 to 15% (stepsize of 5%).
+        See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+      allOf:
+        - $ref: /schemas/types.yaml#/definitions/uint32
+        - minimum: 0
+          maximum: 3
+          default: 2
+
+    qcom,preemphasis-width:
+      description:
+        It is a 1 bit value that specifies how long the HSTX
+        pre-emphasis (specified using qcom,preemphasis-level) must be in
+        effect. Duration could be half-bit of full-bit.
+        See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+      allOf:
+        - $ref: /schemas/types.yaml#/definitions/uint32
+        - minimum: 0
+          maximum: 1
+          default: 0
+
+    qcom,hsdisc-trim-value:
+      description:
+        It is a 2 bit value tuning parameter that control disconnect
+        threshold and may vary for different boards of same SOC.
+      allOf:
+        - $ref: /schemas/types.yaml#/definitions/uint32
+        - minimum: 0
+          maximum: 3
+          default: 0
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+  - clocks
+  - clock-names
+  - vdda-pll-supply
+  - vdda-phy-dpdm-supply
+  - resets
+
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-msm8996.h>
+    hsusb_phy: phy@7411000 {
+        compatible = "qcom,msm8996-qusb2-phy";
+        reg = <0x7411000 0x180>;
+        #phy-cells = <0>;
+
+        clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+                 <&gcc GCC_RX1_USB2_CLKREF_CLK>;
+        clock-names = "cfg_ahb", "ref";
+
+        vdda-pll-supply = <&pm8994_l12>;
+        vdda-phy-dpdm-supply = <&pm8994_l24>;
+
+        resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+        nvmem-cells = <&qusb2p_hstx_trim>;
+    };

Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,usb-hs-28nm.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys DesignWare Core 28nm High-Speed PHY
+
+maintainers:
+  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+
+description: |
+  Qualcomm Low-Speed, Full-Speed, Hi-Speed 28nm USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,usb-hs-28nm-femtophy
+
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: rpmcc ref clock
+      - description: PHY AHB clock
+      - description: Rentention clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: ahb
+      - const: sleep
+
+  resets:
+    items:
+      - description: PHY core reset
+      - description: POR reset
+
+  reset-names:
+    items:
+      - const: phy
+      - const: por
+
+  vdd-supply:
+    description: phandle to the regulator VDD supply node.
+
+  vdda1p8-supply:
+    description: phandle to the regulator 1.8V supply node.
+
+  vdda3p3-supply:
+    description: phandle to the regulator 3.3V supply node.
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - vdd-supply
+  - vdda1p8-supply
+  - vdda3p3-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    usb2_phy_prim: phy@7a000 {
+        compatible = "qcom,usb-hs-28nm-femtophy";
+        reg = <0x0007a000 0x200>;
+        #phy-cells = <0>;
+        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+                 <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+        clock-names = "ref", "ahb", "sleep";
+        resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>,
+                 <&gcc GCC_USB2A_PHY_BCR>;
+        reset-names = "phy", "por";
+        vdd-supply = <&vreg_l4_1p2>;
+        vdda1p8-supply = <&vreg_l5_1p8>;
+        vdda3p3-supply = <&vreg_l12_3p3>;
+    };
+...

Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/qcom,usb-ss.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
+
+maintainers:
+  - Bryan O'Donoghue <bryan.odonoghue@linaro.org>
+
+description: |
+  Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY
+
+properties:
+  compatible:
+    enum:
+      - qcom,usb-ss-28nm-phy
+
+  reg:
+    maxItems: 1
+
+  "#phy-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: rpmcc clock
+      - description: PHY AHB clock
+      - description: SuperSpeed pipe clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: ahb
+      - const: pipe
+
+  vdd-supply:
+    description: phandle to the regulator VDD supply node.
+
+  vdda1p8-supply:
+    description: phandle to the regulator 1.8V supply node.
+
+  resets:
+    items:
+      - description: COM reset
+      - description: PHY reset line
+
+  reset-names:
+    items:
+      - const: com
+      - const: phy
+
+required:
+  - compatible
+  - reg
+  - "#phy-cells"
+  - clocks
+  - clock-names
+  - vdd-supply
+  - vdda1p8-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+    #include <dt-bindings/clock/qcom,rpmcc.h>
+    usb3_phy: usb3-phy@78000 {
+        compatible = "qcom,usb-ss-28nm-phy";
+        reg = <0x78000 0x400>;
+        #phy-cells = <0>;
+        clocks = <&rpmcc RPM_SMD_LN_BB_CLK>,
+                 <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>,
+                 <&gcc GCC_USB3_PHY_PIPE_CLK>;
+        clock-names = "ref", "ahb", "pipe";
+        resets = <&gcc GCC_USB3_PHY_BCR>,
+                 <&gcc GCC_USB3PHY_PHY_BCR>;
+        reset-names = "com", "phy";
+        vdd-supply = <&vreg_l3_1p05>;
+        vdda1p8-supply = <&vreg_l5_1p8>;
+    };
+...

Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt

-Qualcomm DWC3 HS AND SS PHY CONTROLLER
---------------------------------------
-
-DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer
-controllers.  Each DWC3 PHY controller should have its own node.
-
-Required properties:
-- compatible: should contain one of the following:
-	- "qcom,dwc3-hs-usb-phy" for High Speed Synopsis PHY controller
-	- "qcom,dwc3-ss-usb-phy" for Super Speed Synopsis PHY controller
-- reg: offset and length of the DWC3 PHY controller register set
-- #phy-cells: must be zero
-- clocks: a list of phandles and clock-specifier pairs, one for each entry in
-  clock-names.
-- clock-names: Should contain "ref" for the PHY reference clock
-
-Optional clocks:
-  "xo"		External reference clock
-
-Example:
-		phy@100f8800 {
-			compatible = "qcom,dwc3-hs-usb-phy";
-			reg = <0x100f8800 0x30>;
-			clocks = <&gcc USB30_0_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-		};
-
-		phy@100f8830 {
-			compatible = "qcom,dwc3-ss-usb-phy";
-			reg = <0x100f8830 0x30>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-		};

Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt

@@ -8,10 +8,13 @@ Required properties:
  - compatible: compatible list, contains:
 	       "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
 	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
+	       "qcom,msm8996-qmp-ufs-phy" for 14nm UFS phy on msm8996,
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996,
 	       "qcom,msm8998-qmp-usb3-phy" for USB3 QMP V3 phy on msm8998,
 	       "qcom,msm8998-qmp-ufs-phy" for UFS QMP phy on msm8998,
 	       "qcom,msm8998-qmp-pcie-phy" for PCIe QMP phy on msm8998,
+	       "qcom,sdm845-qhp-pcie-phy" for QHP PCIe phy on sdm845,
+	       "qcom,sdm845-qmp-pcie-phy" for QMP PCIe phy on sdm845,
 	       "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845,
 	       "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845,
 	       "qcom,sdm845-qmp-ufs-phy" for UFS QMP phy on sdm845,
@@ -44,6 +47,8 @@ Required properties:
 		For "qcom,ipq8074-qmp-pcie-phy": no clocks are listed.
 		For "qcom,msm8996-qmp-pcie-phy" must contain:
 			"aux", "cfg_ahb", "ref".
+		For "qcom,msm8996-qmp-ufs-phy" must contain:
+			"ref".
 		For "qcom,msm8996-qmp-usb3-phy" must contain:
 			"aux", "cfg_ahb", "ref".
 		For "qcom,msm8998-qmp-usb3-phy" must contain:
@@ -52,6 +57,10 @@ Required properties:
 			"ref", "ref_aux".
 		For "qcom,msm8998-qmp-pcie-phy" must contain:
 			"aux", "cfg_ahb", "ref".
+		For "qcom,sdm845-qhp-pcie-phy" must contain:
+			"aux", "cfg_ahb", "ref", "refgen".
+		For "qcom,sdm845-qmp-pcie-phy" must contain:
+			"aux", "cfg_ahb", "ref", "refgen".
 		For "qcom,sdm845-qmp-usb3-phy" must contain:
 			"aux", "cfg_ahb", "ref", "com_aux".
 		For "qcom,sdm845-qmp-usb3-uni-phy" must contain:
@@ -72,6 +81,8 @@ Required properties:
 			"phy", "common".
 		For "qcom,msm8996-qmp-pcie-phy" must contain:
 			"phy", "common", "cfg".
+		For "qcom,msm8996-qmp-ufs-phy": must contain:
+			"ufsphy".
 		For "qcom,msm8996-qmp-usb3-phy" must contain
 			"phy", "common".
 		For "qcom,msm8998-qmp-usb3-phy" must contain
@@ -80,6 +91,10 @@ Required properties:
 			"ufsphy".
 		For "qcom,msm8998-qmp-pcie-phy" must contain:
 			"phy", "common".
+		For "qcom,sdm845-qhp-pcie-phy" must contain:
+			"phy".
+		For "qcom,sdm845-qmp-pcie-phy" must contain:
+			"phy".
 		For "qcom,sdm845-qmp-usb3-phy" must contain:
 			"phy", "common".
 		For "qcom,sdm845-qmp-usb3-uni-phy" must contain:

Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt

-Qualcomm QUSB2 phy controller
-=============================
-
-QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
-
-Required properties:
- - compatible: compatible list, contains
-	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
-	       "qcom,msm8998-qusb2-phy" for 10nm PHY on msm8998,
-	       "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845.
-
- - reg: offset and length of the PHY register set.
- - #phy-cells: must be 0.
-
- - clocks: a list of phandles and clock-specifier pairs,
-	   one for each entry in clock-names.
- - clock-names: must be "cfg_ahb" for phy config clock,
-			"ref" for 19.2 MHz ref clk,
-			"iface" for phy interface clock (Optional).
-
- - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
- - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.
-
- - resets: Phandle to reset to phy block.
-
-Optional properties:
- - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
-		tuning parameter value for qusb2 phy.
-
- - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
- - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be
-		added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
-		tuning parameter that may vary for different boards of same SOC.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
- - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX
-		output current.
-		Possible range is - 15mA to 24mA (stepsize of 600 uA).
-		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
-		Default value is 22.2mA for sdm845.
- - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level.
-		Possible range is 0 to 15% (stepsize of 5%).
-		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
-		Default value is 10% for sdm845.
-- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX
-		pre-emphasis (specified using qcom,preemphasis-level) must be in
-		effect. Duration could be half-bit of full-bit.
-		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
-		This property is applicable to only QUSB2 v2 PHY (sdm845).
-		Default value is full-bit width for sdm845.
-
-Example:
-	hsusb_phy: phy@7411000 {
-		compatible = "qcom,msm8996-qusb2-phy";
-		reg = <0x7411000 0x180>;
-		#phy-cells = <0>;
-
-		clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
-			<&gcc GCC_RX1_USB2_CLKREF_CLK>,
-		clock-names = "cfg_ahb", "ref";
-
-		vdda-pll-supply = <&pm8994_l12>;
-		vdda-phy-dpdm-supply = <&pm8994_l24>;
-
-		resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
-		nvmem-cells = <&qusb2p_hstx_trim>;
-        };

Documentation/devicetree/bindings/phy/ti-phy-gmii-sel.txt

@@ -40,6 +40,7 @@ Required properties:
 			  "ti,dra7xx-phy-gmii-sel" for dra7xx/am57xx platform
 			  "ti,am43xx-phy-gmii-sel" for am43xx platform
 			  "ti,dm814-phy-gmii-sel" for dm814x platform
+			  "ti,am654-phy-gmii-sel" for AM654x/J721E platform
 - reg			: Address and length of the register set for the device
 - #phy-cells		: must be 2.
 			  cell 1 - CPSW port number (starting from 1)

Documentation/devicetree/bindings/phy/uniphier-pcie-phy.txt

@@ -5,14 +5,19 @@ PCIe controller implemented on Socionext UniPhier SoCs.
 
 Required properties:
 - compatible: Should contain one of the following:
+    "socionext,uniphier-pro5-pcie-phy" - for Pro5 PHY
     "socionext,uniphier-ld20-pcie-phy" - for LD20 PHY
     "socionext,uniphier-pxs3-pcie-phy" - for PXs3 PHY
 - reg: Specifies offset and length of the register set for the device.
 - #phy-cells: Must be zero.
-- clocks: A phandle to the clock gate for PCIe glue layer including
-	this phy.
-- resets: A phandle to the reset line for PCIe glue layer including
-	this phy.
+- clocks: A list of phandles to the clock gate for PCIe glue layer
+	including this phy.
+- clock-names: For Pro5 only, should contain the following:
+    "gio", "link" - for Pro5 SoC
+- resets: A list of phandles to the reset line for PCIe glue layer
+	including this phy.
+- reset-names: For Pro5 only, should contain the following:
+    "gio", "link" - for Pro5 SoC
 
 Optional properties:
 - socionext,syscon: A phandle to system control to set configurations

Documentation/devicetree/bindings/phy/uniphier-usb3-hsphy.txt

@@ -7,7 +7,7 @@ this describes about High-Speed PHY.
 
 Required properties:
 - compatible: Should contain one of the following:
-    "socionext,uniphier-pro4-usb3-hsphy" - for Pro4 SoC
+    "socionext,uniphier-pro5-usb3-hsphy" - for Pro5 SoC
     "socionext,uniphier-pxs2-usb3-hsphy" - for PXs2 SoC
     "socionext,uniphier-ld20-usb3-hsphy" - for LD20 SoC
     "socionext,uniphier-pxs3-usb3-hsphy" - for PXs3 SoC
@@ -16,13 +16,13 @@ Required properties:
 - clocks: A list of phandles to the clock gate for USB3 glue layer.
 	According to the clock-names, appropriate clocks are required.
 - clock-names: Should contain the following:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro5 SoC
     "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
     "phy", "link" - for others
 - resets: A list of phandles to the reset control for USB3 glue layer.
 	According to the reset-names, appropriate resets are required.
 - reset-names: Should contain the following:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro5 SoC
     "phy", "link" - for others
 
 Optional properties:

Documentation/devicetree/bindings/phy/uniphier-usb3-ssphy.txt

@@ -8,6 +8,7 @@ this describes about Super-Speed PHY.
 Required properties:
 - compatible: Should contain one of the following:
     "socionext,uniphier-pro4-usb3-ssphy" - for Pro4 SoC
+    "socionext,uniphier-pro5-usb3-ssphy" - for Pro5 SoC
     "socionext,uniphier-pxs2-usb3-ssphy" - for PXs2 SoC
     "socionext,uniphier-ld20-usb3-ssphy" - for LD20 SoC
     "socionext,uniphier-pxs3-usb3-ssphy" - for PXs3 SoC
@@ -16,13 +17,13 @@ Required properties:
 - clocks: A list of phandles to the clock gate for USB3 glue layer.
 	According to the clock-names, appropriate clocks are required.
 - clock-names:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro4 and Pro5 SoC
     "phy", "phy-ext", "link" - for PXs3 SoC, "phy-ext" is optional.
     "phy", "link" - for others
 - resets: A list of phandles to the reset control for USB3 glue layer.
 	According to the reset-names, appropriate resets are required.
 - reset-names:
-    "gio", "link" - for Pro4 SoC
+    "gio", "link" - for Pro4 and Pro5 SoC
     "phy", "link" - for others
 
 Optional properties:

Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.yaml

@@ -22,10 +22,14 @@ description: |
   The DWC3 Glue controls the PHY routing and power, an interrupt line is
   connected to the Glue to serve as OTG ID change detection.
 
+  The Amlogic A1 embeds a DWC3 USB IP Core configured for USB2 in
+  host-only mode.
+
 properties:
   compatible:
     enum:
       - amlogic,meson-g12a-usb-ctrl
+      - amlogic,meson-a1-usb-ctrl
 
   ranges: true
 
@@ -84,6 +88,25 @@ required:
   - phys
   - dr_mode
 
+allOf:
+  - if:
+      properties:
+        compatible:
+          enum:
+            - amlogic,meson-a1-usb-ctrl
+
+    then:
+      properties:
+        clocks:
+          minItems: 3
+        clock-names:
+          items:
+            - const: usb_ctrl
+            - const: usb_bus
+            - const: xtal_usb_ctrl
+      required:
+        - clock-names
+
 examples:
   - |
     usb: usb@ffe09000 {

Documentation/devicetree/bindings/usb/aspeed,usb-vhub.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020 Facebook Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/aspeed,usb-vhub.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ASPEED USB 2.0 Virtual Hub Controller
+
+maintainers:
+  - Benjamin Herrenschmidt <benh@kernel.crashing.org>
+
+description: |+
+  The ASPEED USB 2.0 Virtual Hub Controller implements 1 set of USB Hub
+  register and several sets of Device and Endpoint registers to support
+  the Virtual Hub's downstream USB devices.
+
+  Supported number of devices and endpoints vary depending on hardware
+  revisions. AST2400 and AST2500 Virtual Hub supports 5 downstream devices
+  and 15 generic endpoints, while AST2600 Virtual Hub supports 7 downstream
+  devices and 21 generic endpoints.
+
+properties:
+  compatible:
+    enum:
+      - aspeed,ast2400-usb-vhub
+      - aspeed,ast2500-usb-vhub
+      - aspeed,ast2600-usb-vhub
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  aspeed,vhub-downstream-ports:
+    description: Number of downstream ports supported by the Virtual Hub
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 5
+        minimum: 1
+        maximum: 7
+
+  aspeed,vhub-generic-endpoints:
+    description: Number of generic endpoints supported by the Virtual Hub
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 15
+        minimum: 1
+        maximum: 21
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - interrupts
+  - aspeed,vhub-downstream-ports
+  - aspeed,vhub-generic-endpoints
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/aspeed-clock.h>
+    vhub: usb-vhub@1e6a0000 {
+            compatible = "aspeed,ast2500-usb-vhub";
+            reg = <0x1e6a0000 0x300>;
+            interrupts = <5>;
+            clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+            aspeed,vhub-downstream-ports = <5>;
+            aspeed,vhub-generic-endpoints = <15>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&pinctrl_usb2ad_default>;
+    };

Documentation/devicetree/bindings/usb/dwc2.yaml

@@ -18,27 +18,15 @@ properties:
           - const: rockchip,rk3066-usb
           - const: snps,dwc2
       - items:
-          - const: rockchip,px30-usb
-          - const: rockchip,rk3066-usb
-          - const: snps,dwc2
-      - items:
-          - const: rockchip,rk3036-usb
-          - const: rockchip,rk3066-usb
-          - const: snps,dwc2
-      - items:
-          - const: rockchip,rv1108-usb
-          - const: rockchip,rk3066-usb
-          - const: snps,dwc2
-      - items:
-          - const: rockchip,rk3188-usb
-          - const: rockchip,rk3066-usb
-          - const: snps,dwc2
-      - items:
-          - const: rockchip,rk3228-usb
-          - const: rockchip,rk3066-usb
-          - const: snps,dwc2
-      - items:
-          - const: rockchip,rk3288-usb
+          - enum:
+            - rockchip,px30-usb
+            - rockchip,rk3036-usb
+            - rockchip,rk3188-usb
+            - rockchip,rk3228-usb
+            - rockchip,rk3288-usb
+            - rockchip,rk3328-usb
+            - rockchip,rk3368-usb
+            - rockchip,rv1108-usb
           - const: rockchip,rk3066-usb
           - const: snps,dwc2
       - const: lantiq,arx100-usb

Documentation/devicetree/bindings/usb/dwc3.txt

@@ -7,7 +7,8 @@ Required properties:
  - compatible: must be "snps,dwc3"
  - reg : Address and length of the register set for the device
  - interrupts: Interrupts used by the dwc3 controller.
- - clock-names: should contain "ref", "bus_early", "suspend"
+ - clock-names: list of clock names. Ideally should be "ref",
+                "bus_early", "suspend" but may be less or more.
  - clocks: list of phandle and clock specifier pairs corresponding to
            entries in the clock-names property.
 
@@ -36,7 +37,7 @@ Optional properties:
  - phys: from the *Generic PHY* bindings
  - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy"
 	or "usb3-phy".
- - resets: a single pair of phandle and reset specifier
+ - resets: set of phandle and reset specifier pairs
  - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM
  - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable
  - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command
@@ -75,6 +76,8 @@ Optional properties:
 			from P0 to P1/P2/P3 without delay.
  - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check
 			during HS transmit.
+ - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in
+			park mode are disabled.
  - snps,dis_metastability_quirk: when set, disable metastability workaround.
 			CAUTION: use only if you are absolutely sure of it.
  - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal

Documentation/devicetree/bindings/usb/generic.txt

@@ -35,6 +35,12 @@ Optional properties:
 			the USB data role (USB host or USB device) for a given
 			USB connector, such as Type-C, Type-B(micro).
 			see connector/usb-connector.txt.
+ - role-switch-default-mode: indicating if usb-role-switch is enabled, the
+			device default operation mode of controller while usb
+			role is USB_ROLE_NONE. Valid arguments are "host" and
+			"peripheral". Defaults to "peripheral" if not
+			specified.
+
 
 This is an attribute to a USB controller such as:
 

Documentation/devicetree/bindings/usb/ingenic,jz4740-musb.txt

-Ingenic JZ4740 MUSB driver
-
-Required properties:
-
-- compatible: Must be "ingenic,jz4740-musb"
-- reg: Address range of the UDC register set
-- interrupts: IRQ number related to the UDC hardware
-- interrupt-names: must be "mc"
-- clocks: phandle to the "udc" clock
-- clock-names: must be "udc"
-- phys: phandle to the USB PHY
-
-Example:
-
-usb_phy: usb-phy@0 {
-	compatible = "usb-nop-xceiv";
-	#phy-cells = <0>;
-};
-
-udc: usb@13040000 {
-	compatible = "ingenic,jz4740-musb";
-	reg = <0x13040000 0x10000>;
-
-	interrupt-parent = <&intc>;
-	interrupts = <24>;
-	interrupt-names = "mc";
-
-	clocks = <&cgu JZ4740_CLK_UDC>;
-	clock-names = "udc";
-
-	phys = <&usb_phy>;
-};

Documentation/devicetree/bindings/usb/ingenic,jz4770-phy.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/ingenic,jz4770-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic JZ4770 USB PHY devicetree bindings
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+properties:
+  $nodename:
+    pattern: '^usb-phy@.*'
+
+  compatible:
+    enum:
+      - ingenic,jz4770-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  vcc-supply:
+    description: VCC power supply
+
+  '#phy-cells':
+    const: 0
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - vcc-supply
+  - '#phy-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/jz4770-cgu.h>
+    otg_phy: usb-phy@3c {
+      compatible = "ingenic,jz4770-phy";
+      reg = <0x3c 0x10>;
+
+      vcc-supply = <&vcc>;
+      clocks = <&cgu JZ4770_CLK_OTG_PHY>;
+
+      #phy-cells = <0>;
+    };

Documentation/devicetree/bindings/usb/ingenic,musb.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/ingenic,musb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic JZ47xx USB IP DT bindings
+
+maintainers:
+  - Paul Cercueil <paul@crapouillou.net>
+
+properties:
+  $nodename:
+    pattern: '^usb@.*'
+
+  compatible:
+    oneOf:
+      - enum:
+        - ingenic,jz4770-musb
+        - ingenic,jz4740-musb
+      - items:
+        - const: ingenic,jz4725b-musb
+        - const: ingenic,jz4740-musb
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: udc
+
+  interrupts:
+    maxItems: 1
+
+  interrupt-names:
+    items:
+      - const: mc
+
+  phys:
+    description: PHY specifier for the USB PHY
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - interrupts
+  - interrupt-names
+  - phys
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/jz4740-cgu.h>
+    usb_phy: usb-phy@0 {
+      compatible = "usb-nop-xceiv";
+      #phy-cells = <0>;
+    };
+
+    udc: usb@13040000 {
+      compatible = "ingenic,jz4740-musb";
+      reg = <0x13040000 0x10000>;
+
+      interrupt-parent = <&intc>;
+      interrupts = <24>;
+      interrupt-names = "mc";
+
+      clocks = <&cgu JZ4740_CLK_UDC>;
+      clock-names = "udc";
+
+      phys = <&usb_phy>;
+    };

Documentation/devicetree/bindings/usb/maxim,max3420-udc.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/maxim,max3420-udc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MAXIM MAX3420/1 USB Peripheral Controller
+
+maintainers:
+  - Jassi Brar <jaswinder.singh@linaro.org>
+
+description: |
+  The controller provices USB2.0 compliant FullSpeed peripheral
+  implementation over the SPI interface.
+
+  Specifications about the part can be found at:
+    http://datasheets.maximintegrated.com/en/ds/MAX3420E.pdf
+
+properties:
+  compatible:
+    enum:
+      - maxim,max3420-udc
+      - maxim,max3421-udc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: usb irq from max3420
+      - description: vbus detection irq
+    minItems: 1
+    maxItems: 2
+
+  interrupt-names:
+    items:
+      - const: udc
+      - const: vbus
+    minItems: 1
+    maxItems: 2
+
+  spi-max-frequency:
+    maximum: 26000000
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+
+additionalProperties: false
+
+examples:
+  - |
+      #include <dt-bindings/gpio/gpio.h>
+      #include <dt-bindings/interrupt-controller/irq.h>
+      spi0 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            udc@0 {
+                  compatible = "maxim,max3420-udc";
+                  reg = <0>;
+                  interrupt-parent = <&gpio>;
+                  interrupts = <0 IRQ_TYPE_EDGE_FALLING>, <10 IRQ_TYPE_EDGE_BOTH>;
+                  interrupt-names = "udc", "vbus";
+                  spi-max-frequency = <12500000>;
+            };
+      };

Documentation/driver-api/usb/typec_bus.rst

@@ -53,9 +53,7 @@ in need to reconfigure the pins on the connector, the alternate mode driver
 needs to notify the bus using :c:func:`typec_altmode_notify()`. The driver
 passes the negotiated SVID specific pin configuration value to the function as
 parameter. The bus driver will then configure the mux behind the connector using
-that value as the state value for the mux, and also call blocking notification
-chain to notify the external drivers about the state of the connector that need
-to know it.
+that value as the state value for the mux.
 
 NOTE: The SVID specific pin configuration values must always start from
 ``TYPEC_STATE_MODAL``. USB Type-C specification defines two default states for
@@ -80,19 +78,6 @@ Helper macro ``TYPEC_MODAL_STATE()`` can also be used::
 #define ALTMODEX_CONF_A = TYPEC_MODAL_STATE(0);
 #define ALTMODEX_CONF_B = TYPEC_MODAL_STATE(1);
 
-Notification chain
-~~~~~~~~~~~~~~~~~~
-
-The drivers for the components that the alternate modes are designed for need to
-get details regarding the results of the negotiation with the partner, and the
-pin configuration of the connector. In case of DisplayPort alternate mode for
-example, the GPU drivers will need to know those details. In case of
-Thunderbolt alternate mode, the thunderbolt drivers will need to know them, and
-so on.
-
-The notification chain is designed for this purpose. The drivers can register
-notifiers with :c:func:`typec_altmode_register_notifier()`.
-
 Cable plug alternate modes
 ~~~~~~~~~~~~~~~~~~~~~~~~~~
 
@@ -129,8 +114,3 @@ Cable Plug operations
 
 .. kernel-doc:: drivers/usb/typec/bus.c
    :functions: typec_altmode_get_plug typec_altmode_put_plug
-
-Notifications
-~~~~~~~~~~~~~
-.. kernel-doc:: drivers/usb/typec/class.c
-   :functions: typec_altmode_register_notifier typec_altmode_unregister_notifier

Documentation/usb/index.rst

@@ -22,6 +22,7 @@ USB support
     misc_usbsevseg
     mtouchusb
     ohci
+    raw-gadget
     usbip_protocol
     usbmon
     usb-serial

Documentation/usb/raw-gadget.rst

+==============
+USB Raw Gadget
+==============
+
+USB Raw Gadget is a kernel module that provides a userspace interface for
+the USB Gadget subsystem. Essentially it allows to emulate USB devices
+from userspace. Enabled with CONFIG_USB_RAW_GADGET. Raw Gadget is
+currently a strictly debugging feature and shouldn't be used in
+production, use GadgetFS instead.
+
+Comparison to GadgetFS
+~~~~~~~~~~~~~~~~~~~~~~
+
+Raw Gadget is similar to GadgetFS, but provides a more low-level and
+direct access to the USB Gadget layer for the userspace. The key
+differences are:
+
+1. Every USB request is passed to the userspace to get a response, while
+   GadgetFS responds to some USB requests internally based on the provided
+   descriptors. However note, that the UDC driver might respond to some
+   requests on its own and never forward them to the Gadget layer.
+
+2. GadgetFS performs some sanity checks on the provided USB descriptors,
+   while Raw Gadget allows you to provide arbitrary data as responses to
+   USB requests.
+
+3. Raw Gadget provides a way to select a UDC device/driver to bind to,
+   while GadgetFS currently binds to the first available UDC.
+
+4. Raw Gadget uses predictable endpoint names (handles) across different
+   UDCs (as long as UDCs have enough endpoints of each required transfer
+   type).
+
+5. Raw Gadget has ioctl-based interface instead of a filesystem-based one.
+
+Userspace interface
+~~~~~~~~~~~~~~~~~~~
+
+To create a Raw Gadget instance open /dev/raw-gadget. Multiple raw-gadget
+instances (bound to different UDCs) can be used at the same time. The
+interaction with the opened file happens through the ioctl() calls, see
+comments in include/uapi/linux/usb/raw_gadget.h for details.
+
+The typical usage of Raw Gadget looks like:
+
+1. Open Raw Gadget instance via /dev/raw-gadget.
+2. Initialize the instance via USB_RAW_IOCTL_INIT.
+3. Launch the instance with USB_RAW_IOCTL_RUN.
+4. In a loop issue USB_RAW_IOCTL_EVENT_FETCH calls to receive events from
+   Raw Gadget and react to those depending on what kind of USB device
+   needs to be emulated.
+
+Potential future improvements
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+- Implement ioctl's for setting/clearing halt status on endpoints.
+
+- Reporting more events (suspend, resume, etc.) through
+  USB_RAW_IOCTL_EVENT_FETCH.
+
+- Support O_NONBLOCK I/O.

MAINTAINERS

@@ -17218,6 +17218,12 @@ S:	Maintained
 F:	Documentation/usb/acm.rst
 F:	drivers/usb/class/cdc-acm.*
 
+USB APPLE MFI FASTCHARGE DRIVER
+M:	Bastien Nocera <hadess@hadess.net>
+L:	linux-usb@vger.kernel.org
+S:	Maintained
+F:	drivers/usb/misc/apple-mfi-fastcharge.c
+
 USB AR5523 WIRELESS DRIVER
 M:	Pontus Fuchs <pontus.fuchs@gmail.com>
 L:	linux-wireless@vger.kernel.org

arch/arm/boot/dts/aspeed-g4.dtsi

@@ -164,6 +164,8 @@ vhub: usb-vhub@1e6a0000 {
 			reg = <0x1e6a0000 0x300>;
 			interrupts = <5>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			aspeed,vhub-downstream-ports = <5>;
+			aspeed,vhub-generic-endpoints = <15>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2d_default>;
 			status = "disabled";

arch/arm/boot/dts/aspeed-g5.dtsi

@@ -195,6 +195,8 @@ vhub: usb-vhub@1e6a0000 {
 			reg = <0x1e6a0000 0x300>;
 			interrupts = <5>;
 			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			aspeed,vhub-downstream-ports = <5>;
+			aspeed,vhub-generic-endpoints = <15>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2ad_default>;
 			status = "disabled";

arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi

@@ -1112,6 +1112,31 @@ pinctrl_uart9_default: uart9_default {
 		groups = "UART9";
 	};
 
+	pinctrl_usb2ah_default: usb2ah_default {
+		function = "USB2AH";
+		groups = "USBA";
+	};
+
+	pinctrl_usb2ad_default: usb2ad_default {
+		function = "USB2AD";
+		groups = "USBA";
+	};
+
+	pinctrl_usb2bh_default: usb2bh_default {
+		function = "USB2BH";
+		groups = "USBB";
+	};
+
+	pinctrl_usb2bd_default: usb2bd_default {
+		function = "USB2BD";
+		groups = "USBB";
+	};
+
+	pinctrl_usb11bhid_default: usb11bhid_default {
+		function = "USB11BHID";
+		groups = "USBB";
+	};
+
 	pinctrl_vb_default: vb_default {
 		function = "VB";
 		groups = "VB";

arch/arm/boot/dts/aspeed-g6.dtsi

@@ -245,6 +245,51 @@ mac3: ftgmac@1e690000 {
 			status = "disabled";
 		};
 
+		ehci0: usb@1e6a1000 {
+			compatible = "aspeed,ast2600-ehci", "generic-ehci";
+			reg = <0x1e6a1000 0x100>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2ah_default>;
+			status = "disabled";
+		};
+
+		ehci1: usb@1e6a3000 {
+			compatible = "aspeed,ast2600-ehci", "generic-ehci";
+			reg = <0x1e6a3000 0x100>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2bh_default>;
+			status = "disabled";
+		};
+
+		uhci: usb@1e6b0000 {
+			compatible = "aspeed,ast2600-uhci", "generic-uhci";
+			reg = <0x1e6b0000 0x100>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			#ports = <2>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBUHCICLK>;
+			status = "disabled";
+			/*
+			 * No default pinmux, it will follow EHCI, use an
+			 * explicit pinmux override if EHCI is not enabled.
+			 */
+		};
+
+		vhub: usb-vhub@1e6a0000 {
+			compatible = "aspeed,ast2600-usb-vhub";
+			reg = <0x1e6a0000 0x350>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT1CLK>;
+			aspeed,vhub-downstream-ports = <7>;
+			aspeed,vhub-generic-endpoints = <21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2ad_default>;
+			status = "disabled";
+		};
+
 		apb {
 			compatible = "simple-bus";
 			#address-cells = <1>;

drivers/base/platform.c

@@ -62,6 +62,28 @@ struct resource *platform_get_resource(struct platform_device *dev,
 EXPORT_SYMBOL_GPL(platform_get_resource);
 
 #ifdef CONFIG_HAS_IOMEM
+/**
+ * devm_platform_get_and_ioremap_resource - call devm_ioremap_resource() for a
+ *					    platform device and get resource
+ *
+ * @pdev: platform device to use both for memory resource lookup as well as
+ *        resource management
+ * @index: resource index
+ * @res: optional output parameter to store a pointer to the obtained resource.
+ */
+void __iomem *
+devm_platform_get_and_ioremap_resource(struct platform_device *pdev,
+				unsigned int index, struct resource **res)
+{
+	struct resource *r;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, index);
+	if (res)
+		*res = r;
+	return devm_ioremap_resource(&pdev->dev, r);
+}
+EXPORT_SYMBOL_GPL(devm_platform_get_and_ioremap_resource);
+
 /**
  * devm_platform_ioremap_resource - call devm_ioremap_resource() for a platform
  *				    device
@@ -73,10 +95,7 @@ EXPORT_SYMBOL_GPL(platform_get_resource);
 void __iomem *devm_platform_ioremap_resource(struct platform_device *pdev,
 					     unsigned int index)
 {
-	struct resource *res;
-
-	res = platform_get_resource(pdev, IORESOURCE_MEM, index);
-	return devm_ioremap_resource(&pdev->dev, res);
+	return devm_platform_get_and_ioremap_resource(pdev, index, NULL);
 }
 EXPORT_SYMBOL_GPL(devm_platform_ioremap_resource);
 

drivers/phy/amlogic/phy-meson-g12a-usb2.c

@@ -66,7 +66,7 @@
 #define PHY_CTRL_R14						0x38
 	#define PHY_CTRL_R14_I_RDP_EN				BIT(0)
 	#define PHY_CTRL_R14_I_RPU_SW1_EN			BIT(1)
-	#define PHY_CTRL_R14_I_RPU_SW2_EN			GENMASK(2, 3)
+	#define PHY_CTRL_R14_I_RPU_SW2_EN			GENMASK(3, 2)
 	#define PHY_CTRL_R14_PG_RSTN				BIT(4)
 	#define PHY_CTRL_R14_I_C2L_DATA_16_8			BIT(5)
 	#define PHY_CTRL_R14_I_C2L_ASSERT_SINGLE_EN_ZERO	BIT(6)
@@ -146,11 +146,17 @@
 #define RESET_COMPLETE_TIME					1000
 #define PLL_RESET_COMPLETE_TIME					100
 
+enum meson_soc_id {
+	MESON_SOC_G12A  = 0,
+	MESON_SOC_A1,
+};
+
 struct phy_meson_g12a_usb2_priv {
 	struct device		*dev;
 	struct regmap		*regmap;
 	struct clk		*clk;
 	struct reset_control	*reset;
+	int                     soc_id;
 };
 
 static const struct regmap_config phy_meson_g12a_usb2_regmap_conf = {
@@ -164,6 +170,7 @@ static int phy_meson_g12a_usb2_init(struct phy *phy)
 {
 	struct phy_meson_g12a_usb2_priv *priv = phy_get_drvdata(phy);
 	int ret;
+	unsigned int value;
 
 	ret = reset_control_reset(priv->reset);
 	if (ret)
@@ -192,18 +199,22 @@ static int phy_meson_g12a_usb2_init(struct phy *phy)
 		     FIELD_PREP(PHY_CTRL_R17_MPLL_FILTER_PVT2, 2) |
 		     FIELD_PREP(PHY_CTRL_R17_MPLL_FILTER_PVT1, 9));
 
-	regmap_write(priv->regmap, PHY_CTRL_R18,
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_LKW_SEL, 1) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_LK_W, 9) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_LK_S, 0x27) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_PFD_GAIN, 1) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_ROU, 7) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_DATA_SEL, 3) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_BIAS_ADJ, 1) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_BB_MODE, 0) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_ALPHA, 3) |
-		     FIELD_PREP(PHY_CTRL_R18_MPLL_ADJ_LDO, 1) |
-		     PHY_CTRL_R18_MPLL_ACG_RANGE);
+	value = FIELD_PREP(PHY_CTRL_R18_MPLL_LKW_SEL, 1) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_LK_W, 9) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_LK_S, 0x27) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_PFD_GAIN, 1) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_ROU, 7) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_DATA_SEL, 3) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_BIAS_ADJ, 1) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_BB_MODE, 0) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_ALPHA, 3) |
+		FIELD_PREP(PHY_CTRL_R18_MPLL_ADJ_LDO, 1) |
+		PHY_CTRL_R18_MPLL_ACG_RANGE;
+
+	if (priv->soc_id == MESON_SOC_A1)
+		value |= PHY_CTRL_R18_MPLL_DCO_CLK_SEL;
+
+	regmap_write(priv->regmap, PHY_CTRL_R18, value);
 
 	udelay(PLL_RESET_COMPLETE_TIME);
 
@@ -227,13 +238,24 @@ static int phy_meson_g12a_usb2_init(struct phy *phy)
 		     FIELD_PREP(PHY_CTRL_R20_USB2_BGR_VREF_4_0, 0) |
 		     FIELD_PREP(PHY_CTRL_R20_USB2_BGR_DBG_1_0, 0));
 
-	regmap_write(priv->regmap, PHY_CTRL_R4,
-		     FIELD_PREP(PHY_CTRL_R4_CALIB_CODE_7_0, 0xf) |
-		     FIELD_PREP(PHY_CTRL_R4_CALIB_CODE_15_8, 0xf) |
-		     FIELD_PREP(PHY_CTRL_R4_CALIB_CODE_23_16, 0xf) |
-		     PHY_CTRL_R4_TEST_BYPASS_MODE_EN |
-		     FIELD_PREP(PHY_CTRL_R4_I_C2L_BIAS_TRIM_1_0, 0) |
-		     FIELD_PREP(PHY_CTRL_R4_I_C2L_BIAS_TRIM_3_2, 0));
+	if (priv->soc_id == MESON_SOC_G12A)
+		regmap_write(priv->regmap, PHY_CTRL_R4,
+			     FIELD_PREP(PHY_CTRL_R4_CALIB_CODE_7_0, 0xf) |
+			     FIELD_PREP(PHY_CTRL_R4_CALIB_CODE_15_8, 0xf) |
+			     FIELD_PREP(PHY_CTRL_R4_CALIB_CODE_23_16, 0xf) |
+			     PHY_CTRL_R4_TEST_BYPASS_MODE_EN |
+			     FIELD_PREP(PHY_CTRL_R4_I_C2L_BIAS_TRIM_1_0, 0) |
+			     FIELD_PREP(PHY_CTRL_R4_I_C2L_BIAS_TRIM_3_2, 0));
+	else if (priv->soc_id == MESON_SOC_A1) {
+		regmap_write(priv->regmap, PHY_CTRL_R21,
+			     PHY_CTRL_R21_USB2_CAL_ACK_EN |
+			     PHY_CTRL_R21_USB2_TX_STRG_PD |
+			     FIELD_PREP(PHY_CTRL_R21_USB2_OTG_ACA_TRIM_1_0, 2));
+
+		/* Analog Settings */
+		regmap_write(priv->regmap, PHY_CTRL_R13,
+			     FIELD_PREP(PHY_CTRL_R13_MIN_COUNT_FOR_SYNC_DET, 7));
+	}
 
 	/* Tuning Disconnect Threshold */
 	regmap_write(priv->regmap, PHY_CTRL_R3,
@@ -241,11 +263,13 @@ static int phy_meson_g12a_usb2_init(struct phy *phy)
 		     FIELD_PREP(PHY_CTRL_R3_HSDIC_REF, 1) |
 		     FIELD_PREP(PHY_CTRL_R3_DISC_THRESH, 3));
 
-	/* Analog Settings */
-	regmap_write(priv->regmap, PHY_CTRL_R14, 0);
-	regmap_write(priv->regmap, PHY_CTRL_R13,
-		     PHY_CTRL_R13_UPDATE_PMA_SIGNALS |
-		     FIELD_PREP(PHY_CTRL_R13_MIN_COUNT_FOR_SYNC_DET, 7));
+	if (priv->soc_id == MESON_SOC_G12A) {
+		/* Analog Settings */
+		regmap_write(priv->regmap, PHY_CTRL_R14, 0);
+		regmap_write(priv->regmap, PHY_CTRL_R13,
+			     PHY_CTRL_R13_UPDATE_PMA_SIGNALS |
+			     FIELD_PREP(PHY_CTRL_R13_MIN_COUNT_FOR_SYNC_DET, 7));
+	}
 
 	return 0;
 }
@@ -286,6 +310,8 @@ static int phy_meson_g12a_usb2_probe(struct platform_device *pdev)
 	if (IS_ERR(base))
 		return PTR_ERR(base);
 
+	priv->soc_id = (enum meson_soc_id)of_device_get_match_data(&pdev->dev);
+
 	priv->regmap = devm_regmap_init_mmio(dev, base,
 					     &phy_meson_g12a_usb2_regmap_conf);
 	if (IS_ERR(priv->regmap))
@@ -321,8 +347,15 @@ static int phy_meson_g12a_usb2_probe(struct platform_device *pdev)
 }
 
 static const struct of_device_id phy_meson_g12a_usb2_of_match[] = {
-	{ .compatible = "amlogic,g12a-usb2-phy", },
-	{ },
+	{
+		.compatible = "amlogic,g12a-usb2-phy",
+		.data = (void *)MESON_SOC_G12A,
+	},
+	{
+		.compatible = "amlogic,a1-usb2-phy",
+		.data = (void *)MESON_SOC_A1,
+	},
+	{ /* Sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, phy_meson_g12a_usb2_of_match);
 

drivers/phy/cadence/Kconfig

@@ -3,13 +3,13 @@
 # Phy drivers for Cadence PHYs
 #
 
-config PHY_CADENCE_DP
-	tristate "Cadence MHDP DisplayPort PHY driver"
+config PHY_CADENCE_TORRENT
+	tristate "Cadence Torrent PHY driver"
 	depends on OF
 	depends on HAS_IOMEM
 	select GENERIC_PHY
 	help
-	  Support for Cadence MHDP DisplayPort PHY.
+	  Support for Cadence Torrent PHY.
 
 config PHY_CADENCE_DPHY
 	tristate "Cadence D-PHY Support"

drivers/phy/cadence/Makefile

 # SPDX-License-Identifier: GPL-2.0-only
-obj-$(CONFIG_PHY_CADENCE_DP)	+= phy-cadence-dp.o
+obj-$(CONFIG_PHY_CADENCE_TORRENT)	+= phy-cadence-torrent.o
 obj-$(CONFIG_PHY_CADENCE_DPHY)	+= cdns-dphy.o
 obj-$(CONFIG_PHY_CADENCE_SIERRA)	+= phy-cadence-sierra.o

drivers/phy/mediatek/phy-mtk-tphy.c

@@ -43,6 +43,8 @@
 #define PA0_RG_USB20_INTR_EN		BIT(5)
 
 #define U3P_USBPHYACR1		0x004
+#define PA1_RG_INTR_CAL		GENMASK(23, 19)
+#define PA1_RG_INTR_CAL_VAL(x)	((0x1f & (x)) << 19)
 #define PA1_RG_VRT_SEL			GENMASK(14, 12)
 #define PA1_RG_VRT_SEL_VAL(x)	((0x7 & (x)) << 12)
 #define PA1_RG_TERM_SEL		GENMASK(10, 8)
@@ -60,6 +62,8 @@
 #define U3P_USBPHYACR6		0x018
 #define PA6_RG_U2_BC11_SW_EN		BIT(23)
 #define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
+#define PA6_RG_U2_DISCTH		GENMASK(7, 4)
+#define PA6_RG_U2_DISCTH_VAL(x)	((0xf & (x)) << 4)
 #define PA6_RG_U2_SQTH		GENMASK(3, 0)
 #define PA6_RG_U2_SQTH_VAL(x)	(0xf & (x))
 
@@ -294,20 +298,21 @@ struct mtk_phy_instance {
 		struct u2phy_banks u2_banks;
 		struct u3phy_banks u3_banks;
 	};
-	struct clk *ref_clk;	/* reference clock of anolog phy */
+	struct clk *ref_clk;	/* reference clock of (digital) phy */
+	struct clk *da_ref_clk;	/* reference clock of analog phy */
 	u32 index;
 	u8 type;
 	int eye_src;
 	int eye_vrt;
 	int eye_term;
+	int intr;
+	int discth;
 	bool bc12_en;
 };
 
 struct mtk_tphy {
 	struct device *dev;
 	void __iomem *sif_base;	/* only shared sif */
-	/* deprecated, use @ref_clk instead in phy instance */
-	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
 	const struct mtk_phy_pdata *pdata;
 	struct mtk_phy_instance **phys;
 	int nphys;
@@ -850,9 +855,14 @@ static void phy_parse_property(struct mtk_tphy *tphy,
 				 &instance->eye_vrt);
 	device_property_read_u32(dev, "mediatek,eye-term",
 				 &instance->eye_term);
-	dev_dbg(dev, "bc12:%d, src:%d, vrt:%d, term:%d\n",
+	device_property_read_u32(dev, "mediatek,intr",
+				 &instance->intr);
+	device_property_read_u32(dev, "mediatek,discth",
+				 &instance->discth);
+	dev_dbg(dev, "bc12:%d, src:%d, vrt:%d, term:%d, intr:%d, disc:%d\n",
 		instance->bc12_en, instance->eye_src,
-		instance->eye_vrt, instance->eye_term);
+		instance->eye_vrt, instance->eye_term,
+		instance->intr, instance->discth);
 }
 
 static void u2_phy_props_set(struct mtk_tphy *tphy,
@@ -888,6 +898,20 @@ static void u2_phy_props_set(struct mtk_tphy *tphy,
 		tmp |= PA1_RG_TERM_SEL_VAL(instance->eye_term);
 		writel(tmp, com + U3P_USBPHYACR1);
 	}
+
+	if (instance->intr) {
+		tmp = readl(com + U3P_USBPHYACR1);
+		tmp &= ~PA1_RG_INTR_CAL;
+		tmp |= PA1_RG_INTR_CAL_VAL(instance->intr);
+		writel(tmp, com + U3P_USBPHYACR1);
+	}
+
+	if (instance->discth) {
+		tmp = readl(com + U3P_USBPHYACR6);
+		tmp &= ~PA6_RG_U2_DISCTH;
+		tmp |= PA6_RG_U2_DISCTH_VAL(instance->discth);
+		writel(tmp, com + U3P_USBPHYACR6);
+	}
 }
 
 static int mtk_phy_init(struct phy *phy)
@@ -896,15 +920,16 @@ static int mtk_phy_init(struct phy *phy)
 	struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
 	int ret;
 
-	ret = clk_prepare_enable(tphy->u3phya_ref);
+	ret = clk_prepare_enable(instance->ref_clk);
 	if (ret) {
-		dev_err(tphy->dev, "failed to enable u3phya_ref\n");
+		dev_err(tphy->dev, "failed to enable ref_clk\n");
 		return ret;
 	}
 
-	ret = clk_prepare_enable(instance->ref_clk);
+	ret = clk_prepare_enable(instance->da_ref_clk);
 	if (ret) {
-		dev_err(tphy->dev, "failed to enable ref_clk\n");
+		dev_err(tphy->dev, "failed to enable da_ref\n");
+		clk_disable_unprepare(instance->ref_clk);
 		return ret;
 	}
 
@@ -967,7 +992,7 @@ static int mtk_phy_exit(struct phy *phy)
 		u2_phy_instance_exit(tphy, instance);
 
 	clk_disable_unprepare(instance->ref_clk);
-	clk_disable_unprepare(tphy->u3phya_ref);
+	clk_disable_unprepare(instance->da_ref_clk);
 	return 0;
 }
 
@@ -1102,11 +1127,6 @@ static int mtk_tphy_probe(struct platform_device *pdev)
 		}
 	}
 
-	/* it's deprecated, make it optional for backward compatibility */
-	tphy->u3phya_ref = devm_clk_get_optional(dev, "u3phya_ref");
-	if (IS_ERR(tphy->u3phya_ref))
-		return PTR_ERR(tphy->u3phya_ref);
-
 	tphy->src_ref_clk = U3P_REF_CLK;
 	tphy->src_coef = U3P_SLEW_RATE_COEF;
 	/* update parameters of slew rate calibrate if exist */
@@ -1153,16 +1173,20 @@ static int mtk_tphy_probe(struct platform_device *pdev)
 		phy_set_drvdata(phy, instance);
 		port++;
 
-		/* if deprecated clock is provided, ignore instance's one */
-		if (tphy->u3phya_ref)
-			continue;
-
-		instance->ref_clk = devm_clk_get(&phy->dev, "ref");
+		instance->ref_clk = devm_clk_get_optional(&phy->dev, "ref");
 		if (IS_ERR(instance->ref_clk)) {
 			dev_err(dev, "failed to get ref_clk(id-%d)\n", port);
 			retval = PTR_ERR(instance->ref_clk);
 			goto put_child;
 		}
+
+		instance->da_ref_clk =
+			devm_clk_get_optional(&phy->dev, "da_ref");
+		if (IS_ERR(instance->da_ref_clk)) {
+			dev_err(dev, "failed to get da_ref_clk(id-%d)\n", port);
+			retval = PTR_ERR(instance->da_ref_clk);
+			goto put_child;
+		}
 	}
 
 	provider = devm_of_phy_provider_register(dev, mtk_phy_xlate);

drivers/phy/qualcomm/Kconfig

@@ -91,3 +91,23 @@ config PHY_QCOM_USB_HSIC
 	select GENERIC_PHY
 	help
 	  Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
+config PHY_QCOM_USB_HS_28NM
+	tristate "Qualcomm 28nm High-Speed PHY"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Enable this to support the Qualcomm Synopsys DesignWare Core 28nm
+	  High-Speed PHY driver. This driver supports the Hi-Speed PHY which
+	  is usually paired with either the ChipIdea or Synopsys DWC3 USB
+	  IPs on MSM SOCs.
+
+config PHY_QCOM_USB_SS
+	tristate "Qualcomm USB Super-Speed PHY driver"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on EXTCON || !EXTCON # if EXTCON=m, this cannot be built-in
+	select GENERIC_PHY
+	help
+	  Enable this to support the Super-Speed USB transceiver on various
+	  Qualcomm chipsets.

drivers/phy/qualcomm/Makefile

@@ -10,3 +10,5 @@ obj-$(CONFIG_PHY_QCOM_UFS_14NM)		+= phy-qcom-ufs-qmp-14nm.o
 obj-$(CONFIG_PHY_QCOM_UFS_20NM)		+= phy-qcom-ufs-qmp-20nm.o
 obj-$(CONFIG_PHY_QCOM_USB_HS) 		+= phy-qcom-usb-hs.o
 obj-$(CONFIG_PHY_QCOM_USB_HSIC) 	+= phy-qcom-usb-hsic.o
+obj-$(CONFIG_PHY_QCOM_USB_HS_28NM)	+= phy-qcom-usb-hs-28nm.o
+obj-$(CONFIG_PHY_QCOM_USB_SS)		+= phy-qcom-usb-ss.o

drivers/phy/qualcomm/phy-qcom-qmp.h

@@ -409,4 +409,118 @@
 #define QPHY_V4_TX_MID_TERM_CTRL1			0x1d8
 #define QPHY_V4_MULTI_LANE_CTRL1			0x1e0
 
+/* PCIE GEN3 COM registers */
+#define PCIE_GEN3_QHP_COM_SSC_EN_CENTER			0x14
+#define PCIE_GEN3_QHP_COM_SSC_PER1			0x20
+#define PCIE_GEN3_QHP_COM_SSC_PER2			0x24
+#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE1		0x28
+#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE2		0x2c
+#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE1_MODE1		0x34
+#define PCIE_GEN3_QHP_COM_SSC_STEP_SIZE2_MODE1		0x38
+#define PCIE_GEN3_QHP_COM_BIAS_EN_CKBUFLR_EN		0x54
+#define PCIE_GEN3_QHP_COM_CLK_ENABLE1			0x58
+#define PCIE_GEN3_QHP_COM_LOCK_CMP1_MODE0		0x6c
+#define PCIE_GEN3_QHP_COM_LOCK_CMP2_MODE0		0x70
+#define PCIE_GEN3_QHP_COM_LOCK_CMP1_MODE1		0x78
+#define PCIE_GEN3_QHP_COM_LOCK_CMP2_MODE1		0x7c
+#define PCIE_GEN3_QHP_COM_BGV_TRIM			0x98
+#define PCIE_GEN3_QHP_COM_CP_CTRL_MODE0			0xb4
+#define PCIE_GEN3_QHP_COM_CP_CTRL_MODE1			0xb8
+#define PCIE_GEN3_QHP_COM_PLL_RCTRL_MODE0		0xc0
+#define PCIE_GEN3_QHP_COM_PLL_RCTRL_MODE1		0xc4
+#define PCIE_GEN3_QHP_COM_PLL_CCTRL_MODE0		0xcc
+#define PCIE_GEN3_QHP_COM_PLL_CCTRL_MODE1		0xd0
+#define PCIE_GEN3_QHP_COM_SYSCLK_EN_SEL			0xdc
+#define PCIE_GEN3_QHP_COM_RESTRIM_CTRL2			0xf0
+#define PCIE_GEN3_QHP_COM_LOCK_CMP_EN			0xf8
+#define PCIE_GEN3_QHP_COM_DEC_START_MODE0		0x100
+#define PCIE_GEN3_QHP_COM_DEC_START_MODE1		0x108
+#define PCIE_GEN3_QHP_COM_DIV_FRAC_START1_MODE0		0x11c
+#define PCIE_GEN3_QHP_COM_DIV_FRAC_START2_MODE0		0x120
+#define PCIE_GEN3_QHP_COM_DIV_FRAC_START3_MODE0		0x124
+#define PCIE_GEN3_QHP_COM_DIV_FRAC_START1_MODE1		0x128
+#define PCIE_GEN3_QHP_COM_DIV_FRAC_START2_MODE1		0x12c
+#define PCIE_GEN3_QHP_COM_DIV_FRAC_START3_MODE1		0x130
+#define PCIE_GEN3_QHP_COM_INTEGLOOP_GAIN0_MODE0		0x150
+#define PCIE_GEN3_QHP_COM_INTEGLOOP_GAIN0_MODE1		0x158
+#define PCIE_GEN3_QHP_COM_VCO_TUNE_MAP			0x178
+#define PCIE_GEN3_QHP_COM_BG_CTRL			0x1c8
+#define PCIE_GEN3_QHP_COM_CLK_SELECT			0x1cc
+#define PCIE_GEN3_QHP_COM_HSCLK_SEL1			0x1d0
+#define PCIE_GEN3_QHP_COM_CORECLK_DIV			0x1e0
+#define PCIE_GEN3_QHP_COM_CORE_CLK_EN			0x1e8
+#define PCIE_GEN3_QHP_COM_CMN_CONFIG			0x1f0
+#define PCIE_GEN3_QHP_COM_SVS_MODE_CLK_SEL		0x1fc
+#define PCIE_GEN3_QHP_COM_CORECLK_DIV_MODE1		0x21c
+#define PCIE_GEN3_QHP_COM_CMN_MODE			0x224
+#define PCIE_GEN3_QHP_COM_VREGCLK_DIV1			0x228
+#define PCIE_GEN3_QHP_COM_VREGCLK_DIV2			0x22c
+
+/* PCIE GEN3 QHP Lane registers */
+#define PCIE_GEN3_QHP_L0_DRVR_CTRL0			0xc
+#define PCIE_GEN3_QHP_L0_DRVR_CTRL1			0x10
+#define PCIE_GEN3_QHP_L0_DRVR_CTRL2			0x14
+#define PCIE_GEN3_QHP_L0_DRVR_TAP_EN			0x18
+#define PCIE_GEN3_QHP_L0_TX_BAND_MODE			0x60
+#define PCIE_GEN3_QHP_L0_LANE_MODE			0x64
+#define PCIE_GEN3_QHP_L0_PARALLEL_RATE			0x7c
+#define PCIE_GEN3_QHP_L0_CML_CTRL_MODE0			0xc0
+#define PCIE_GEN3_QHP_L0_CML_CTRL_MODE1			0xc4
+#define PCIE_GEN3_QHP_L0_CML_CTRL_MODE2			0xc8
+#define PCIE_GEN3_QHP_L0_PREAMP_CTRL_MODE1		0xd0
+#define PCIE_GEN3_QHP_L0_PREAMP_CTRL_MODE2		0xd4
+#define PCIE_GEN3_QHP_L0_MIXER_CTRL_MODE0		0xd8
+#define PCIE_GEN3_QHP_L0_MIXER_CTRL_MODE1		0xdc
+#define PCIE_GEN3_QHP_L0_MIXER_CTRL_MODE2		0xe0
+#define PCIE_GEN3_QHP_L0_CTLE_THRESH_DFE		0xfc
+#define PCIE_GEN3_QHP_L0_CGA_THRESH_DFE			0x100
+#define PCIE_GEN3_QHP_L0_RXENGINE_EN0			0x108
+#define PCIE_GEN3_QHP_L0_CTLE_TRAIN_TIME		0x114
+#define PCIE_GEN3_QHP_L0_CTLE_DFE_OVRLP_TIME		0x118
+#define PCIE_GEN3_QHP_L0_DFE_REFRESH_TIME		0x11c
+#define PCIE_GEN3_QHP_L0_DFE_ENABLE_TIME		0x120
+#define PCIE_GEN3_QHP_L0_VGA_GAIN			0x124
+#define PCIE_GEN3_QHP_L0_DFE_GAIN			0x128
+#define PCIE_GEN3_QHP_L0_EQ_GAIN			0x130
+#define PCIE_GEN3_QHP_L0_OFFSET_GAIN			0x134
+#define PCIE_GEN3_QHP_L0_PRE_GAIN			0x138
+#define PCIE_GEN3_QHP_L0_VGA_INITVAL			0x13c
+#define PCIE_GEN3_QHP_L0_EQ_INTVAL			0x154
+#define PCIE_GEN3_QHP_L0_EDAC_INITVAL			0x160
+#define PCIE_GEN3_QHP_L0_RXEQ_INITB0			0x168
+#define PCIE_GEN3_QHP_L0_RXEQ_INITB1			0x16c
+#define PCIE_GEN3_QHP_L0_RCVRDONE_THRESH1		0x178
+#define PCIE_GEN3_QHP_L0_RXEQ_CTRL			0x180
+#define PCIE_GEN3_QHP_L0_UCDR_FO_GAIN_MODE0		0x184
+#define PCIE_GEN3_QHP_L0_UCDR_FO_GAIN_MODE1		0x188
+#define PCIE_GEN3_QHP_L0_UCDR_FO_GAIN_MODE2		0x18c
+#define PCIE_GEN3_QHP_L0_UCDR_SO_GAIN_MODE0		0x190
+#define PCIE_GEN3_QHP_L0_UCDR_SO_GAIN_MODE1		0x194
+#define PCIE_GEN3_QHP_L0_UCDR_SO_GAIN_MODE2		0x198
+#define PCIE_GEN3_QHP_L0_UCDR_SO_CONFIG			0x19c
+#define PCIE_GEN3_QHP_L0_RX_BAND			0x1a4
+#define PCIE_GEN3_QHP_L0_RX_RCVR_PATH1_MODE0		0x1c0
+#define PCIE_GEN3_QHP_L0_RX_RCVR_PATH1_MODE1		0x1c4
+#define PCIE_GEN3_QHP_L0_RX_RCVR_PATH1_MODE2		0x1c8
+#define PCIE_GEN3_QHP_L0_SIGDET_ENABLES			0x230
+#define PCIE_GEN3_QHP_L0_SIGDET_CNTRL			0x234
+#define PCIE_GEN3_QHP_L0_SIGDET_DEGLITCH_CNTRL		0x238
+#define PCIE_GEN3_QHP_L0_DCC_GAIN			0x2a4
+#define PCIE_GEN3_QHP_L0_RSM_START			0x2a8
+#define PCIE_GEN3_QHP_L0_RX_EN_SIGNAL			0x2ac
+#define PCIE_GEN3_QHP_L0_PSM_RX_EN_CAL			0x2b0
+#define PCIE_GEN3_QHP_L0_RX_MISC_CNTRL0			0x2b8
+#define PCIE_GEN3_QHP_L0_TS0_TIMER			0x2c0
+#define PCIE_GEN3_QHP_L0_DLL_HIGHDATARATE		0x2c4
+#define PCIE_GEN3_QHP_L0_RX_RESETCODE_OFFSET		0x2cc
+
+/* PCIE GEN3 PCS registers */
+#define PCIE_GEN3_QHP_PHY_TXMGN_MAIN_V0_M3P5DB		0x2c
+#define PCIE_GEN3_QHP_PHY_TXMGN_POST_V0_M3P5DB		0x40
+#define PCIE_GEN3_QHP_PHY_TXMGN_MAIN_V0_M6DB		0x54
+#define PCIE_GEN3_QHP_PHY_TXMGN_POST_V0_M6DB		0x68
+#define PCIE_GEN3_QHP_PHY_POWER_STATE_CONFIG		0x15c
+#define PCIE_GEN3_QHP_PHY_POWER_STATE_CONFIG5		0x16c
+#define PCIE_GEN3_QHP_PHY_PCS_TX_RX_CONFIG		0x174
+
 #endif