Commit dcadf59e authored by Hans de Goede's avatar Hans de Goede Committed by Maxime Ripard

ARM: sun4i: dt: Add support for the A10-OLinuXino-LIME board

This add support for the A10-OLinuXino-LIME:
https://www.olimex.com/Products/OLinuXino/A10/A10-OLinuXino-LIME

A low cost Allwinner A10 based dev-board, with sata, ethernet, hdmi and 2x USB.
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent e2f02651
...@@ -282,6 +282,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += \ ...@@ -282,6 +282,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += \
sun4i-a10-cubieboard.dtb \ sun4i-a10-cubieboard.dtb \
sun4i-a10-mini-xplus.dtb \ sun4i-a10-mini-xplus.dtb \
sun4i-a10-hackberry.dtb \ sun4i-a10-hackberry.dtb \
sun4i-a10-olinuxino-lime.dtb \
sun4i-a10-pcduino.dtb \ sun4i-a10-pcduino.dtb \
sun5i-a10s-olinuxino-micro.dtb \ sun5i-a10s-olinuxino-micro.dtb \
sun5i-a13-olinuxino.dtb \ sun5i-a13-olinuxino.dtb \
......
/*
* Copyright 2014 - Hans de Goede <hdegoede@redhat.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
/include/ "sun4i-a10.dtsi"
/include/ "sunxi-common-regulators.dtsi"
/ {
model = "Olimex A10-OLinuXino-LIME";
compatible = "olimex,a10-olinuxino-lime", "allwinner,sun4i-a10";
soc@01c00000 {
emac: ethernet@01c0b000 {
pinctrl-names = "default";
pinctrl-0 = <&emac_pins_a>;
phy = <&phy1>;
status = "okay";
};
mdio@01c0b080 {
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
};
};
usbphy: phy@01c13400 {
usb1_vbus-supply = <&reg_usb1_vbus>;
usb2_vbus-supply = <&reg_usb2_vbus>;
status = "okay";
};
ehci0: usb@01c14000 {
status = "okay";
};
ohci0: usb@01c14400 {
status = "okay";
};
ahci: sata@01c18000 {
target-supply = <&reg_ahci_5v>;
status = "okay";
};
ehci1: usb@01c1c000 {
status = "okay";
};
ohci1: usb@01c1c400 {
status = "okay";
};
pinctrl@01c20800 {
ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 {
allwinner,pins = "PC3";
allwinner,function = "gpio_out";
allwinner,drive = <0>;
allwinner,pull = <0>;
};
led_pins_olinuxinolime: led_pins@0 {
allwinner,pins = "PH2";
allwinner,function = "gpio_out";
allwinner,drive = <1>;
allwinner,pull = <0>;
};
};
uart0: serial@01c28000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins_olinuxinolime>;
green {
label = "a10-olinuxino-lime:green:usr";
gpios = <&pio 7 2 0>;
default-state = "on";
};
};
reg_ahci_5v: ahci-5v {
pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>;
gpio = <&pio 2 3 0>;
status = "okay";
};
reg_usb1_vbus: usb1-vbus {
status = "okay";
};
reg_usb2_vbus: usb2-vbus {
status = "okay";
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment