libata: set queue DMA alignment to sector size for ATAPI too

commit 729a6a30 upstream.

ata_pio_sectors() expects buffer for each sector to be contained in a
single page; otherwise, it ends up overrunning the first page.  This
is achieved by setting queue DMA alignment.  If sector_size is smaller
than PAGE_SIZE and all buffers are sector_size aligned, buffer for
each sector is always contained in a single page.

This wasn't applied to ATAPI devices but IDENTIFY_PACKET is executed
as ATA_PROT_PIO and thus uses ata_pio_sectors().  Newer versions of
udev issue IDENTIFY_PACKET with unaligned buffer triggering the
problem and causing oops.

This patch fixes the problem by setting sdev->sector_size to
ATA_SECT_SIZE on ATATPI devices and always setting DMA alignment to
sector_size.  While at it, add a warning for the unlikely but still
possible scenario where sector_size is larger than PAGE_SIZE, in which
case the alignment wouldn't be enough.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: John Stanley <jpsinthemix@verizon.net>
Tested-by: John Stanley <jpsinthemix@verizon.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/ata/libata-scsi.c

@@ -1102,9 +1102,9 @@ static int ata_scsi_dev_config(struct scsi_device *sdev,
 		struct request_queue *q = sdev->request_queue;
 		void *buf;
 
-		/* set the min alignment and padding */
-		blk_queue_update_dma_alignment(sdev->request_queue,
-					       ATA_DMA_PAD_SZ - 1);
+		sdev->sector_size = ATA_SECT_SIZE;
+
+		/* set DMA padding */
 		blk_queue_update_dma_pad(sdev->request_queue,
 					 ATA_DMA_PAD_SZ - 1);
 
@@ -1118,13 +1118,25 @@ static int ata_scsi_dev_config(struct scsi_device *sdev,
 
 		blk_queue_dma_drain(q, atapi_drain_needed, buf, ATAPI_MAX_DRAIN);
 	} else {
-		/* ATA devices must be sector aligned */
 		sdev->sector_size = ata_id_logical_sector_size(dev->id);
-		blk_queue_update_dma_alignment(sdev->request_queue,
-					       sdev->sector_size - 1);
 		sdev->manage_start_stop = 1;
 	}
 
+	/*
+	 * ata_pio_sectors() expects buffer for each sector to not cross
+	 * page boundary.  Enforce it by requiring buffers to be sector
+	 * aligned, which works iff sector_size is not larger than
+	 * PAGE_SIZE.  ATAPI devices also need the alignment as
+	 * IDENTIFY_PACKET is executed as ATA_PROT_PIO.
+	 */
+	if (sdev->sector_size > PAGE_SIZE)
+		ata_dev_printk(dev, KERN_WARNING,
+			"sector_size=%u > PAGE_SIZE, PIO may malfunction\n",
+			sdev->sector_size);
+
+	blk_queue_update_dma_alignment(sdev->request_queue,
+				       sdev->sector_size - 1);
+
 	if (dev->flags & ATA_DFLAG_AN)
 		set_bit(SDEV_EVT_MEDIA_CHANGE, sdev->supported_events);