Merge tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging/iio fixes from Greg KH:
 "Here are some Staging and IIO driver fixes for 4.13-rc5.

  Nothing major, just a number of small fixes for reported issues. All
  of these have been in linux-next for a while now with no reported
  issues. Full details are in the shortlog"

* tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: comedi_fops: do not call blocking ops when !TASK_RUNNING
  iio: aspeed-adc: wait for initial sequence.
  iio: accel: bmc150: Always restore device to normal mode after suspend-resume
  staging:iio:resolver:ad2s1210 fix negative IIO_ANGL_VEL read
  iio: adc: axp288: Fix the GPADC pin reading often wrongly returning 0
  iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits
  iio: accel: st_accel: add SPI-3wire support
  iio: adc: Revert "axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"
  iio: adc: sun4i-gpadc-iio: fix unbalanced irq enable/disable
  iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
  iio: light: tsl2563: use correct event code

drivers/iio/accel/bmc150-accel-core.c

@@ -193,7 +193,6 @@ struct bmc150_accel_data {
 	struct regmap *regmap;
 	int irq;
 	struct bmc150_accel_interrupt interrupts[BMC150_ACCEL_INTERRUPTS];
-	atomic_t active_intr;
 	struct bmc150_accel_trigger triggers[BMC150_ACCEL_TRIGGERS];
 	struct mutex mutex;
 	u8 fifo_mode, watermark;
@@ -493,11 +492,6 @@ static int bmc150_accel_set_interrupt(struct bmc150_accel_data *data, int i,
 		goto out_fix_power_state;
 	}
 
-	if (state)
-		atomic_inc(&data->active_intr);
-	else
-		atomic_dec(&data->active_intr);
-
 	return 0;
 
 out_fix_power_state:
@@ -1710,8 +1704,7 @@ static int bmc150_accel_resume(struct device *dev)
 	struct bmc150_accel_data *data = iio_priv(indio_dev);
 
 	mutex_lock(&data->mutex);
-	if (atomic_read(&data->active_intr))
-		bmc150_accel_set_mode(data, BMC150_ACCEL_SLEEP_MODE_NORMAL, 0);
+	bmc150_accel_set_mode(data, BMC150_ACCEL_SLEEP_MODE_NORMAL, 0);
 	bmc150_accel_fifo_set_mode(data);
 	mutex_unlock(&data->mutex);
 

drivers/iio/accel/st_accel_core.c

@@ -166,6 +166,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_ihl = 0x02,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
+		.sim = {
+			.addr = 0x23,
+			.value = BIT(0),
+		},
 		.multi_read_bit = true,
 		.bootime = 2,
 	},
@@ -234,6 +238,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_od = 0x40,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
+		.sim = {
+			.addr = 0x23,
+			.value = BIT(0),
+		},
 		.multi_read_bit = true,
 		.bootime = 2,
 	},
@@ -316,6 +324,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 				.en_mask = 0x08,
 			},
 		},
+		.sim = {
+			.addr = 0x24,
+			.value = BIT(0),
+		},
 		.multi_read_bit = false,
 		.bootime = 2,
 	},
@@ -379,6 +391,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_int1 = 0x04,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
+		.sim = {
+			.addr = 0x21,
+			.value = BIT(1),
+		},
 		.multi_read_bit = true,
 		.bootime = 2, /* guess */
 	},
@@ -437,6 +453,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_od = 0x40,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
+		.sim = {
+			.addr = 0x21,
+			.value = BIT(7),
+		},
 		.multi_read_bit = false,
 		.bootime = 2, /* guess */
 	},
@@ -499,6 +519,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.addr_ihl = 0x22,
 			.mask_ihl = 0x80,
 		},
+		.sim = {
+			.addr = 0x23,
+			.value = BIT(0),
+		},
 		.multi_read_bit = true,
 		.bootime = 2,
 	},
@@ -547,6 +571,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_int1 = 0x04,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
+		.sim = {
+			.addr = 0x21,
+			.value = BIT(1),
+		},
 		.multi_read_bit = false,
 		.bootime = 2,
 	},
@@ -614,6 +642,10 @@ static const struct st_sensor_settings st_accel_sensors_settings[] = {
 			.mask_ihl = 0x02,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
+		.sim = {
+			.addr = 0x23,
+			.value = BIT(0),
+		},
 		.multi_read_bit = true,
 		.bootime = 2,
 	},

drivers/iio/adc/aspeed_adc.c

@@ -22,6 +22,7 @@
 
 #include <linux/iio/iio.h>
 #include <linux/iio/driver.h>
+#include <linux/iopoll.h>
 
 #define ASPEED_RESOLUTION_BITS		10
 #define ASPEED_CLOCKS_PER_SAMPLE	12
@@ -38,11 +39,17 @@
 
 #define ASPEED_ENGINE_ENABLE		BIT(0)
 
+#define ASPEED_ADC_CTRL_INIT_RDY	BIT(8)
+
+#define ASPEED_ADC_INIT_POLLING_TIME	500
+#define ASPEED_ADC_INIT_TIMEOUT		500000
+
 struct aspeed_adc_model_data {
 	const char *model_name;
 	unsigned int min_sampling_rate;	// Hz
 	unsigned int max_sampling_rate;	// Hz
 	unsigned int vref_voltage;	// mV
+	bool wait_init_sequence;
 };
 
 struct aspeed_adc_data {
@@ -211,6 +218,24 @@ static int aspeed_adc_probe(struct platform_device *pdev)
 		goto scaler_error;
 	}
 
+	model_data = of_device_get_match_data(&pdev->dev);
+
+	if (model_data->wait_init_sequence) {
+		/* Enable engine in normal mode. */
+		writel(ASPEED_OPERATION_MODE_NORMAL | ASPEED_ENGINE_ENABLE,
+		       data->base + ASPEED_REG_ENGINE_CONTROL);
+
+		/* Wait for initial sequence complete. */
+		ret = readl_poll_timeout(data->base + ASPEED_REG_ENGINE_CONTROL,
+					 adc_engine_control_reg_val,
+					 adc_engine_control_reg_val &
+					 ASPEED_ADC_CTRL_INIT_RDY,
+					 ASPEED_ADC_INIT_POLLING_TIME,
+					 ASPEED_ADC_INIT_TIMEOUT);
+		if (ret)
+			goto scaler_error;
+	}
+
 	/* Start all channels in normal mode. */
 	ret = clk_prepare_enable(data->clk_scaler->clk);
 	if (ret)
@@ -274,6 +299,7 @@ static const struct aspeed_adc_model_data ast2500_model_data = {
 	.vref_voltage = 1800, // mV
 	.min_sampling_rate = 1,
 	.max_sampling_rate = 1000000,
+	.wait_init_sequence = true,
 };
 
 static const struct of_device_id aspeed_adc_matches[] = {

drivers/iio/adc/axp288_adc.c

@@ -28,6 +28,8 @@
 #include <linux/iio/driver.h>
 
 #define AXP288_ADC_EN_MASK		0xF1
+#define AXP288_ADC_TS_PIN_GPADC		0xF2
+#define AXP288_ADC_TS_PIN_ON		0xF3
 
 enum axp288_adc_id {
 	AXP288_ADC_TS,
@@ -121,6 +123,26 @@ static int axp288_adc_read_channel(int *val, unsigned long address,
 	return IIO_VAL_INT;
 }
 
+static int axp288_adc_set_ts(struct regmap *regmap, unsigned int mode,
+				unsigned long address)
+{
+	int ret;
+
+	/* channels other than GPADC do not need to switch TS pin */
+	if (address != AXP288_GP_ADC_H)
+		return 0;
+
+	ret = regmap_write(regmap, AXP288_ADC_TS_PIN_CTRL, mode);
+	if (ret)
+		return ret;
+
+	/* When switching to the GPADC pin give things some time to settle */
+	if (mode == AXP288_ADC_TS_PIN_GPADC)
+		usleep_range(6000, 10000);
+
+	return 0;
+}
+
 static int axp288_adc_read_raw(struct iio_dev *indio_dev,
 			struct iio_chan_spec const *chan,
 			int *val, int *val2, long mask)
@@ -131,7 +153,16 @@ static int axp288_adc_read_raw(struct iio_dev *indio_dev,
 	mutex_lock(&indio_dev->mlock);
 	switch (mask) {
 	case IIO_CHAN_INFO_RAW:
+		if (axp288_adc_set_ts(info->regmap, AXP288_ADC_TS_PIN_GPADC,
+					chan->address)) {
+			dev_err(&indio_dev->dev, "GPADC mode\n");
+			ret = -EINVAL;
+			break;
+		}
 		ret = axp288_adc_read_channel(val, chan->address, info->regmap);
+		if (axp288_adc_set_ts(info->regmap, AXP288_ADC_TS_PIN_ON,
+						chan->address))
+			dev_err(&indio_dev->dev, "TS pin restore\n");
 		break;
 	default:
 		ret = -EINVAL;
@@ -141,6 +172,15 @@ static int axp288_adc_read_raw(struct iio_dev *indio_dev,
 	return ret;
 }
 
+static int axp288_adc_set_state(struct regmap *regmap)
+{
+	/* ADC should be always enabled for internal FG to function */
+	if (regmap_write(regmap, AXP288_ADC_TS_PIN_CTRL, AXP288_ADC_TS_PIN_ON))
+		return -EIO;
+
+	return regmap_write(regmap, AXP20X_ADC_EN1, AXP288_ADC_EN_MASK);
+}
+
 static const struct iio_info axp288_adc_iio_info = {
 	.read_raw = &axp288_adc_read_raw,
 	.driver_module = THIS_MODULE,
@@ -169,7 +209,7 @@ static int axp288_adc_probe(struct platform_device *pdev)
 	 * Set ADC to enabled state at all time, including system suspend.
 	 * otherwise internal fuel gauge functionality may be affected.
 	 */
-	ret = regmap_write(info->regmap, AXP20X_ADC_EN1, AXP288_ADC_EN_MASK);
+	ret = axp288_adc_set_state(axp20x->regmap);
 	if (ret) {
 		dev_err(&pdev->dev, "unable to enable ADC device\n");
 		return ret;

drivers/iio/adc/sun4i-gpadc-iio.c

@@ -256,6 +256,7 @@ static int sun4i_gpadc_read(struct iio_dev *indio_dev, int channel, int *val,
 
 err:
 	pm_runtime_put_autosuspend(indio_dev->dev.parent);
+	disable_irq(irq);
 	mutex_unlock(&info->mutex);
 
 	return ret;
@@ -365,7 +366,6 @@ static irqreturn_t sun4i_gpadc_temp_data_irq_handler(int irq, void *dev_id)
 		complete(&info->completion);
 
 out:
-	disable_irq_nosync(info->temp_data_irq);
 	return IRQ_HANDLED;
 }
 
@@ -380,7 +380,6 @@ static irqreturn_t sun4i_gpadc_fifo_data_irq_handler(int irq, void *dev_id)
 		complete(&info->completion);
 
 out:
-	disable_irq_nosync(info->fifo_data_irq);
 	return IRQ_HANDLED;
 }
 

drivers/iio/adc/vf610_adc.c

@@ -77,7 +77,7 @@
 #define VF610_ADC_ADSTS_MASK		0x300
 #define VF610_ADC_ADLPC_EN		0x80
 #define VF610_ADC_ADHSC_EN		0x400
-#define VF610_ADC_REFSEL_VALT		0x100
+#define VF610_ADC_REFSEL_VALT		0x800
 #define VF610_ADC_REFSEL_VBG		0x1000
 #define VF610_ADC_ADTRG_HARD		0x2000
 #define VF610_ADC_AVGS_8		0x4000

drivers/iio/common/st_sensors/st_sensors_core.c

@@ -550,6 +550,31 @@ int st_sensors_read_info_raw(struct iio_dev *indio_dev,
 }
 EXPORT_SYMBOL(st_sensors_read_info_raw);
 
+static int st_sensors_init_interface_mode(struct iio_dev *indio_dev,
+			const struct st_sensor_settings *sensor_settings)
+{
+	struct st_sensor_data *sdata = iio_priv(indio_dev);
+	struct device_node *np = sdata->dev->of_node;
+	struct st_sensors_platform_data *pdata;
+
+	pdata = (struct st_sensors_platform_data *)sdata->dev->platform_data;
+	if (((np && of_property_read_bool(np, "spi-3wire")) ||
+	     (pdata && pdata->spi_3wire)) && sensor_settings->sim.addr) {
+		int err;
+
+		err = sdata->tf->write_byte(&sdata->tb, sdata->dev,
+					    sensor_settings->sim.addr,
+					    sensor_settings->sim.value);
+		if (err < 0) {
+			dev_err(&indio_dev->dev,
+				"failed to init interface mode\n");
+			return err;
+		}
+	}
+
+	return 0;
+}
+
 int st_sensors_check_device_support(struct iio_dev *indio_dev,
 			int num_sensors_list,
 			const struct st_sensor_settings *sensor_settings)
@@ -574,6 +599,10 @@ int st_sensors_check_device_support(struct iio_dev *indio_dev,
 		return -ENODEV;
 	}
 
+	err = st_sensors_init_interface_mode(indio_dev, &sensor_settings[i]);
+	if (err < 0)
+		return err;
+
 	if (sensor_settings[i].wai_addr) {
 		err = sdata->tf->read_byte(&sdata->tb, sdata->dev,
 					   sensor_settings[i].wai_addr, &wai);

drivers/iio/light/tsl2563.c

@@ -626,7 +626,7 @@ static irqreturn_t tsl2563_event_handler(int irq, void *private)
 	struct tsl2563_chip *chip = iio_priv(dev_info);
 
 	iio_push_event(dev_info,
-		       IIO_UNMOD_EVENT_CODE(IIO_LIGHT,
+		       IIO_UNMOD_EVENT_CODE(IIO_INTENSITY,
 					    0,
 					    IIO_EV_TYPE_THRESH,
 					    IIO_EV_DIR_EITHER),

drivers/iio/pressure/st_pressure_core.c

@@ -456,7 +456,7 @@ static const struct st_sensor_settings st_press_sensors_settings[] = {
 			.mask_od = 0x40,
 			.addr_stat_drdy = ST_SENSORS_DEFAULT_STAT_ADDR,
 		},
-		.multi_read_bit = true,
+		.multi_read_bit = false,
 		.bootime = 2,
 	},
 };

drivers/staging/comedi/comedi_fops.c

@@ -2396,6 +2396,7 @@ static ssize_t comedi_write(struct file *file, const char __user *buf,
 			continue;
 		}
 
+		set_current_state(TASK_RUNNING);
 		wp = async->buf_write_ptr;
 		n1 = min(n, async->prealloc_bufsz - wp);
 		n2 = n - n1;
@@ -2528,6 +2529,8 @@ static ssize_t comedi_read(struct file *file, char __user *buf, size_t nbytes,
 			}
 			continue;
 		}
+
+		set_current_state(TASK_RUNNING);
 		rp = async->buf_read_ptr;
 		n1 = min(n, async->prealloc_bufsz - rp);
 		n2 = n - n1;

drivers/staging/iio/resolver/ad2s1210.c

@@ -472,7 +472,7 @@ static int ad2s1210_read_raw(struct iio_dev *indio_dev,
 			     long m)
 {
 	struct ad2s1210_state *st = iio_priv(indio_dev);
-	bool negative;
+	u16 negative;
 	int ret = 0;
 	u16 pos;
 	s16 vel;

include/linux/iio/common/st_sensors.h

@@ -105,6 +105,11 @@ struct st_sensor_fullscale {
 	struct st_sensor_fullscale_avl fs_avl[ST_SENSORS_FULLSCALE_AVL_MAX];
 };
 
+struct st_sensor_sim {
+	u8 addr;
+	u8 value;
+};
+
 /**
  * struct st_sensor_bdu - ST sensor device block data update
  * @addr: address of the register.
@@ -197,6 +202,7 @@ struct st_sensor_transfer_function {
  * @bdu: Block data update register.
  * @das: Data Alignment Selection register.
  * @drdy_irq: Data ready register of the sensor.
+ * @sim: SPI serial interface mode register of the sensor.
  * @multi_read_bit: Use or not particular bit for [I2C/SPI] multi-read.
  * @bootime: samples to discard when sensor passing from power-down to power-up.
  */
@@ -213,6 +219,7 @@ struct st_sensor_settings {
 	struct st_sensor_bdu bdu;
 	struct st_sensor_das das;
 	struct st_sensor_data_ready_irq drdy_irq;
+	struct st_sensor_sim sim;
 	bool multi_read_bit;
 	unsigned int bootime;
 };

include/linux/platform_data/st_sensors_pdata.h

@@ -17,10 +17,12 @@
  *	Available only for accelerometer and pressure sensors.
  *	Accelerometer DRDY on LSM330 available only on pin 1 (see datasheet).
  * @open_drain: set the interrupt line to be open drain if possible.
+ * @spi_3wire: enable spi-3wire mode.
  */
 struct st_sensors_platform_data {
 	u8 drdy_int_pin;
 	bool open_drain;
+	bool spi_3wire;
 };
 
 #endif /* ST_SENSORS_PDATA_H */