Commit ddab3838 authored by Huang Shijie's avatar Huang Shijie Committed by David Woodhouse

mtd: gpmi: add a new field for HW_GPMI_TIMING1

The gpmi_nfc_compute_hardware_timing{} should contains all the
fields setting for gpmi timing registers. It already contains the fields
for HW_GPMI_TIMING0 and HW_GPMI_CTRL1.

So it is better to add a new field setting for HW_GPMI_TIMING1 in
this data structure. This makes the code more clear in logic.

This patch also changes some comments to make the code more readable.
Signed-off-by: default avatarHuang Shijie <b32955@freescale.com>
Signed-off-by: default avatarArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
parent 3e70192c
......@@ -728,6 +728,7 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this,
hw->address_setup_in_cycles = address_setup_in_cycles;
hw->use_half_periods = dll_use_half_periods;
hw->sample_delay_factor = sample_delay_factor;
hw->device_busy_timeout = GPMI_DEFAULT_BUSY_TIMEOUT;
/* Return success. */
return 0;
......@@ -752,26 +753,26 @@ void gpmi_begin(struct gpmi_nand_data *this)
goto err_out;
}
/* set ready/busy timeout */
writel(0x500 << BP_GPMI_TIMING1_BUSY_TIMEOUT,
gpmi_regs + HW_GPMI_TIMING1);
/* Get the timing information we need. */
nfc->clock_frequency_in_hz = clk_get_rate(r->clock[0]);
clock_period_in_ns = 1000000000 / nfc->clock_frequency_in_hz;
gpmi_nfc_compute_hardware_timing(this, &hw);
/* Set up all the simple timing parameters. */
/* [1] Set HW_GPMI_TIMING0 */
reg = BF_GPMI_TIMING0_ADDRESS_SETUP(hw.address_setup_in_cycles) |
BF_GPMI_TIMING0_DATA_HOLD(hw.data_hold_in_cycles) |
BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles) ;
writel(reg, gpmi_regs + HW_GPMI_TIMING0);
/*
* DLL_ENABLE must be set to 0 when setting RDN_DELAY or HALF_PERIOD.
*/
/* [2] Set HW_GPMI_TIMING1 */
writel(BF_GPMI_TIMING1_BUSY_TIMEOUT(hw.device_busy_timeout),
gpmi_regs + HW_GPMI_TIMING1);
/* [3] The following code is to set the HW_GPMI_CTRL1. */
/* DLL_ENABLE must be set to 0 when setting RDN_DELAY or HALF_PERIOD. */
writel(BM_GPMI_CTRL1_DLL_ENABLE, gpmi_regs + HW_GPMI_CTRL1_CLR);
/* Clear out the DLL control fields. */
......
......@@ -189,14 +189,24 @@ struct gpmi_nand_data {
* @data_setup_in_cycles: The data setup time, in cycles.
* @data_hold_in_cycles: The data hold time, in cycles.
* @address_setup_in_cycles: The address setup time, in cycles.
* @device_busy_timeout: The timeout waiting for NAND Ready/Busy,
* this value is the number of cycles multiplied
* by 4096.
* @use_half_periods: Indicates the clock is running slowly, so the
* NFC DLL should use half-periods.
* @sample_delay_factor: The sample delay factor.
*/
struct gpmi_nfc_hardware_timing {
/* for HW_GPMI_TIMING0 */
uint8_t data_setup_in_cycles;
uint8_t data_hold_in_cycles;
uint8_t address_setup_in_cycles;
/* for HW_GPMI_TIMING1 */
uint16_t device_busy_timeout;
#define GPMI_DEFAULT_BUSY_TIMEOUT 0x500 /* default busy timeout value.*/
/* for HW_GPMI_CTRL1 */
bool use_half_periods;
uint8_t sample_delay_factor;
};
......
......@@ -154,6 +154,9 @@
#define HW_GPMI_TIMING1 0x00000080
#define BP_GPMI_TIMING1_BUSY_TIMEOUT 16
#define BM_GPMI_TIMING1_BUSY_TIMEOUT (0xffff << BP_GPMI_TIMING1_BUSY_TIMEOUT)
#define BF_GPMI_TIMING1_BUSY_TIMEOUT(v) \
(((v) << BP_GPMI_TIMING1_BUSY_TIMEOUT) & BM_GPMI_TIMING1_BUSY_TIMEOUT)
#define HW_GPMI_TIMING2 0x00000090
#define HW_GPMI_DATA 0x000000a0
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment