riscv: dts: starfive: visionfive 2: Remove non-existing I2S hardware

This partially reverts
commit 92cfc358 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")

This added device tree nodes for I2S hardware that is not actually on the
VisionFive 2 board, but connected on the 40pin header. Many different extension
boards could be added on those pins, so this should be handled by overlays
instead.
This also conflicts with the TDM node which also attempts to grab GPIO 44:

  starfive-jh7110-sys-pinctrl 13040000.pinctrl: pin GPIO44 already requested by 10090000.tdm; cannot claim for 120c0000.i2s

Fixes: 92cfc358 ("riscv: dts: starfive: Add the nodes and pins of I2Srx/I2Stx0/I2Stx1")
Signed-off-by: Hannah Peuckmann <hannah.peuckmann@canonical.com>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Tested-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi

@@ -278,24 +278,6 @@ &i2c6 {
 	status = "okay";
 };
 
-&i2srx {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2srx_pins>;
-	status = "okay";
-};
-
-&i2stx0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mclk_ext_pins>;
-	status = "okay";
-};
-
-&i2stx1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2stx1_pins>;
-	status = "okay";
-};
-
 &mmc0 {
 	max-frequency = <100000000>;
 	assigned-clocks = <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
@@ -446,46 +428,6 @@ GPOEN_SYS_I2C6_DATA,
 		};
 	};
 
-	i2srx_pins: i2srx-0 {
-		clk-sd-pins {
-			pinmux = <GPIOMUX(38, GPOUT_LOW,
-					      GPOEN_DISABLE,
-					      GPI_SYS_I2SRX_BCLK)>,
-				 <GPIOMUX(63, GPOUT_LOW,
-					      GPOEN_DISABLE,
-					      GPI_SYS_I2SRX_LRCK)>,
-				 <GPIOMUX(38, GPOUT_LOW,
-					      GPOEN_DISABLE,
-					      GPI_SYS_I2STX1_BCLK)>,
-				 <GPIOMUX(63, GPOUT_LOW,
-					      GPOEN_DISABLE,
-					      GPI_SYS_I2STX1_LRCK)>,
-				 <GPIOMUX(61, GPOUT_LOW,
-					      GPOEN_DISABLE,
-					      GPI_SYS_I2SRX_SDIN0)>;
-			input-enable;
-		};
-	};
-
-	i2stx1_pins: i2stx1-0 {
-		sd-pins {
-			pinmux = <GPIOMUX(44, GPOUT_SYS_I2STX1_SDO0,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-disable;
-			input-disable;
-		};
-	};
-
-	mclk_ext_pins: mclk-ext-0 {
-		mclk-ext-pins {
-			pinmux = <GPIOMUX(4, GPOUT_LOW,
-					     GPOEN_DISABLE,
-					     GPI_SYS_MCLK_EXT)>;
-			input-enable;
-		};
-	};
-
 	mmc0_pins: mmc0-0 {
 		 rst-pins {
 			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,