mmc: core: Factor out common code in drive strength selection

Make a new function out of common code used for drive
strength selection.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

drivers/mmc/core/core.c

@@ -1639,6 +1639,44 @@ void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type)
 	mmc_host_clk_release(host);
 }
 
+int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr,
+			      int card_drv_type, int *drv_type)
+{
+	struct mmc_host *host = card->host;
+	int host_drv_type = SD_DRIVER_TYPE_B;
+	int drive_strength;
+
+	*drv_type = 0;
+
+	if (!host->ops->select_drive_strength)
+		return 0;
+
+	/* Use SD definition of driver strength for hosts */
+	if (host->caps & MMC_CAP_DRIVER_TYPE_A)
+		host_drv_type |= SD_DRIVER_TYPE_A;
+
+	if (host->caps & MMC_CAP_DRIVER_TYPE_C)
+		host_drv_type |= SD_DRIVER_TYPE_C;
+
+	if (host->caps & MMC_CAP_DRIVER_TYPE_D)
+		host_drv_type |= SD_DRIVER_TYPE_D;
+
+	/*
+	 * The drive strength that the hardware can support
+	 * depends on the board design.  Pass the appropriate
+	 * information and let the hardware specific code
+	 * return what is possible given the options
+	 */
+	mmc_host_clk_hold(host);
+	drive_strength = host->ops->select_drive_strength(card, max_dtr,
+							  host_drv_type,
+							  card_drv_type,
+							  drv_type);
+	mmc_host_clk_release(host);
+
+	return drive_strength;
+}
+
 /*
  * Apply power to the MMC stack.  This is a two-stage process.
  * First, we enable power to the card without the clock running.

drivers/mmc/core/core.h

@@ -50,6 +50,8 @@ int mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage, u32 ocr);
 int __mmc_set_signal_voltage(struct mmc_host *host, int signal_voltage);
 void mmc_set_timing(struct mmc_host *host, unsigned int timing);
 void mmc_set_driver_type(struct mmc_host *host, unsigned int drv_type);
+int mmc_select_drive_strength(struct mmc_card *card, unsigned int max_dtr,
+			      int card_drv_type, int *drv_type);
 void mmc_power_up(struct mmc_host *host, u32 ocr);
 void mmc_power_off(struct mmc_host *host);
 void mmc_power_cycle(struct mmc_host *host, u32 ocr);

drivers/mmc/core/sd.c

@@ -386,35 +386,14 @@ int mmc_sd_switch_hs(struct mmc_card *card)
 
 static int sd_select_driver_type(struct mmc_card *card, u8 *status)
 {
-	int host_drv_type = SD_DRIVER_TYPE_B;
 	int card_drv_type, drive_strength, drv_type;
 	int err;
 
-	if (!card->host->ops->select_drive_strength)
-		return 0;
-
-	if (card->host->caps & MMC_CAP_DRIVER_TYPE_A)
-		host_drv_type |= SD_DRIVER_TYPE_A;
-
-	if (card->host->caps & MMC_CAP_DRIVER_TYPE_C)
-		host_drv_type |= SD_DRIVER_TYPE_C;
-
-	if (card->host->caps & MMC_CAP_DRIVER_TYPE_D)
-		host_drv_type |= SD_DRIVER_TYPE_D;
-
 	card_drv_type = card->sw_caps.sd3_drv_type | SD_DRIVER_TYPE_B;
 
-	/*
-	 * The drive strength that the hardware can support
-	 * depends on the board design.  Pass the appropriate
-	 * information and let the hardware specific code
-	 * return what is possible given the options
-	 */
-	mmc_host_clk_hold(card->host);
-	drive_strength = card->host->ops->select_drive_strength(card,
-		card->sw_caps.uhs_max_dtr,
-		host_drv_type, card_drv_type, &drv_type);
-	mmc_host_clk_release(card->host);
+	drive_strength = mmc_select_drive_strength(card,
+						   card->sw_caps.uhs_max_dtr,
+						   card_drv_type, &drv_type);
 
 	if (drive_strength) {
 		err = mmc_sd_switch(card, 1, 2, drive_strength, status);

drivers/mmc/core/sdio.c

@@ -402,34 +402,15 @@ static unsigned char host_drive_to_sdio_drive(int host_strength)
 
 static void sdio_select_driver_type(struct mmc_card *card)
 {
-	int host_drv_type = SD_DRIVER_TYPE_B;
 	int card_drv_type, drive_strength, drv_type;
 	unsigned char card_strength;
 	int err;
 
-	if (!card->host->ops->select_drive_strength)
-		return;
-
-	if (card->host->caps & MMC_CAP_DRIVER_TYPE_A)
-		host_drv_type |= SD_DRIVER_TYPE_A;
-
-	if (card->host->caps & MMC_CAP_DRIVER_TYPE_C)
-		host_drv_type |= SD_DRIVER_TYPE_C;
-
-	if (card->host->caps & MMC_CAP_DRIVER_TYPE_D)
-		host_drv_type |= SD_DRIVER_TYPE_D;
-
 	card_drv_type = card->sw_caps.sd3_drv_type | SD_DRIVER_TYPE_B;
 
-	/*
-	 * The drive strength that the hardware can support
-	 * depends on the board design.  Pass the appropriate
-	 * information and let the hardware specific code
-	 * return what is possible given the options
-	 */
-	drive_strength = card->host->ops->select_drive_strength(card,
-		card->sw_caps.uhs_max_dtr,
-		host_drv_type, card_drv_type, &drv_type);
+	drive_strength = mmc_select_drive_strength(card,
+						   card->sw_caps.uhs_max_dtr,
+						   card_drv_type, &drv_type);
 
 	if (drive_strength) {
 		/* if error just use default for drive strength B */