Commit e2eaa339 authored by Andrew Lunn's avatar Andrew Lunn Committed by Jason Cooper

ARM: Kirkwood: convert rd88f6281-setup.c to DT.

Perform a mechanical translation of rd88f6281-setup.c into DT.  Since
the hardware differs between the A0 and A1 stepping, two dts files are
used, and a .dtsi file for the common parts. The A0 part does not have
a "wan" port on the switch and uses PHY address 10 to address the
switch. The A1 part does have the "wan" port and uses address 0.
Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarJason Cooper <jason@lakedaemon.net>
parent dd943170
...@@ -113,6 +113,8 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-b3.dtb \ ...@@ -113,6 +113,8 @@ dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-b3.dtb \
kirkwood-openblocks_a6.dtb \ kirkwood-openblocks_a6.dtb \
kirkwood-openblocks_a7.dtb \ kirkwood-openblocks_a7.dtb \
kirkwood-rd88f6192.dtb \ kirkwood-rd88f6192.dtb \
kirkwood-rd88f6281-a0.dtb \
kirkwood-rd88f6281-a1.dtb \
kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug.dtb \
kirkwood-sheevaplug-esata.dtb \ kirkwood-sheevaplug-esata.dtb \
kirkwood-topkick.dtb \ kirkwood-topkick.dtb \
......
/*
* Marvell RD88F6181 A0 Board descrition
*
* Andrew Lunn <andrew@lunn.ch>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*
* This file contains the definitions for the board with the A0 variant of
* the SoC. The ethernet switch does not have a "wan" port.
*/
/dts-v1/;
#include "kirkwood-rd88f6281.dtsi"
/ {
model = "Marvell RD88f6281 Reference design, with A0 SoC";
compatible = "marvell,rd88f6281-a0", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood";
dsa@0 {
switch@0 {
reg = <10 0>; /* MDIO address 10, switch 0 in tree */
};
};
};
\ No newline at end of file
/*
* Marvell RD88F6181 A1 Board descrition
*
* Andrew Lunn <andrew@lunn.ch>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*
* This file contains the definitions for the board with the A1 variant of
* the SoC. The ethernet switch has a "wan" port.
*/
/dts-v1/;
#include "kirkwood-rd88f6281.dtsi"
/ {
model = "Marvell RD88f6281 Reference design, with A1 SoC";
compatible = "marvell,rd88f6281-a1", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood";
dsa@0 {
switch@0 {
reg = <0 0>; /* MDIO address 0, switch 0 in tree */
port@4 {
reg = <4>;
label = "wan";
};
};
};
};
\ No newline at end of file
/*
* Marvell RD88F6181 Common Board descrition
*
* Andrew Lunn <andrew@lunn.ch>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*
* This file contains the definitions that are common between the two
* variants of the Marvell Kirkwood Development Board.
*/
#include "kirkwood.dtsi"
#include "kirkwood-6281.dtsi"
/ {
memory {
device_type = "memory";
reg = <0x00000000 0x20000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8";
};
mbus {
pcie-controller {
status = "okay";
pcie@1,0 {
status = "okay";
};
};
};
ocp@f1000000 {
pinctrl: pinctrl@10000 {
pinctrl-0 = <&pmx_sdio_cd>;
pinctrl-names = "default";
pmx_sdio_cd: pmx-sdio-cd {
marvell,pins = "mpp28";
marvell,function = "gpio";
};
};
serial@12000 {
status = "okay";
};
sata@80000 {
status = "okay";
nr-ports = <2>;
};
mvsdio@90000 {
pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>;
pinctrl-names = "default";
status = "okay";
cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
/* No WP GPIO */
};
};
dsa@0 {
compatible = "marvell,dsa";
#address-cells = <2>;
#size-cells = <0>;
dsa,ethernet = <&eth0>;
dsa,mii-bus = <&ethphy1>;
switch@0 {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
label = "lan1";
};
port@1 {
reg = <1>;
label = "lan2";
};
port@2 {
reg = <2>;
label = "lan3";
};
port@3 {
reg = <3>;
label = "lan4";
};
port@5 {
reg = <5>;
label = "cpu";
};
};
};
};
&nand {
status = "okay";
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
read-only;
};
partition@100000 {
label = "uImage";
reg = <0x0100000 0x200000>;
};
partition@300000 {
label = "data";
reg = <0x0300000 0x500000>;
};
};
&mdio {
status = "okay";
ethphy0: ethernet-phy@0 {
reg = <0>;
};
ethphy1: ethernet-phy@ff {
reg = <0xff>; /* No PHY attached */
speed = <1000>;
duple = <1>;
};
};
&eth0 {
status = "okay";
ethernet0-port@0 {
phy-handle = <&ethphy0>;
};
};
&eth1 {
status = "okay";
ethernet1-port@0 {
phy-handle = <&ethphy1>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment