Commit e303b6af authored by Andy Shevchenko's avatar Andy Shevchenko Committed by David S. Miller

enc28j60: Switch to dev_<level> from pr_<level>

Instead of using open coded printk(KERN_<LEVEL>) switch the driver to use
dev_<level> macros.

Note, the device name will be printed in full, which is beneficial when
more than one card installed on the system.
Signed-off-by: default avatarAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent b4f7a6f9
......@@ -419,14 +419,14 @@ enc28j60_packet_write(struct enc28j60_net *priv, int len, const u8 *data)
static int poll_ready(struct enc28j60_net *priv, u8 reg, u8 mask, u8 val)
{
struct device *dev = &priv->spi->dev;
unsigned long timeout = jiffies + msecs_to_jiffies(20);
/* 20 msec timeout read */
while ((nolock_regb_read(priv, reg) & mask) != val) {
if (time_after(jiffies, timeout)) {
if (netif_msg_drv(priv))
dev_dbg(&priv->spi->dev,
"reg %02x ready timeout!\n", reg);
dev_dbg(dev, "reg %02x ready timeout!\n", reg);
return -ETIMEDOUT;
}
cpu_relax();
......@@ -489,13 +489,13 @@ static int enc28j60_set_hw_macaddr(struct net_device *ndev)
{
int ret;
struct enc28j60_net *priv = netdev_priv(ndev);
struct device *dev = &priv->spi->dev;
mutex_lock(&priv->lock);
if (!priv->hw_enable) {
if (netif_msg_drv(priv))
printk(KERN_INFO DRV_NAME
": %s: Setting MAC address to %pM\n",
ndev->name, ndev->dev_addr);
dev_info(dev, "%s: Setting MAC address to %pM\n",
ndev->name, ndev->dev_addr);
/* NOTE: MAC address in ENC28J60 is byte-backward */
nolock_regb_write(priv, MAADR5, ndev->dev_addr[0]);
nolock_regb_write(priv, MAADR4, ndev->dev_addr[1]);
......@@ -594,12 +594,13 @@ static u16 rx_packet_start(u16 ptr)
static void nolock_rxfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
{
struct device *dev = &priv->spi->dev;
u16 erxrdpt;
if (start > 0x1FFF || end > 0x1FFF || start > end) {
if (netif_msg_drv(priv))
printk(KERN_ERR DRV_NAME ": %s(%d, %d) RXFIFO "
"bad parameters!\n", __func__, start, end);
dev_err(dev, "%s(%d, %d) RXFIFO bad parameters!\n",
__func__, start, end);
return;
}
/* set receive buffer start + end */
......@@ -612,10 +613,12 @@ static void nolock_rxfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
static void nolock_txfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
{
struct device *dev = &priv->spi->dev;
if (start > 0x1FFF || end > 0x1FFF || start > end) {
if (netif_msg_drv(priv))
printk(KERN_ERR DRV_NAME ": %s(%d, %d) TXFIFO "
"bad parameters!\n", __func__, start, end);
dev_err(dev, "%s(%d, %d) TXFIFO bad parameters!\n",
__func__, start, end);
return;
}
/* set transmit buffer start + end */
......@@ -630,9 +633,10 @@ static void nolock_txfifo_init(struct enc28j60_net *priv, u16 start, u16 end)
*/
static void enc28j60_lowpower(struct enc28j60_net *priv, bool is_low)
{
struct device *dev = &priv->spi->dev;
if (netif_msg_drv(priv))
dev_dbg(&priv->spi->dev, "%s power...\n",
is_low ? "low" : "high");
dev_dbg(dev, "%s power...\n", is_low ? "low" : "high");
mutex_lock(&priv->lock);
if (is_low) {
......@@ -651,6 +655,7 @@ static void enc28j60_lowpower(struct enc28j60_net *priv, bool is_low)
static int enc28j60_hw_init(struct enc28j60_net *priv)
{
struct device *dev = &priv->spi->dev;
u8 reg;
if (netif_msg_drv(priv))
......@@ -681,7 +686,7 @@ static int enc28j60_hw_init(struct enc28j60_net *priv)
*/
reg = locked_regb_read(priv, EREVID);
if (netif_msg_drv(priv))
printk(KERN_INFO DRV_NAME ": chip RevID: 0x%02x\n", reg);
dev_info(dev, "chip RevID: 0x%02x\n", reg);
if (reg == 0x00 || reg == 0xff) {
if (netif_msg_drv(priv))
printk(KERN_DEBUG DRV_NAME ": %s() Invalid RevId %d\n",
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment