Merge branch 'part-2-of-sja1105-dsa-driver-preparation-for-new-switch-introduction-sja1110'

Vladimir Oltean says:

====================
Part 2 of SJA1105 DSA driver preparation for new switch introduction (SJA1110)

This series is a continuation of:
https://patchwork.kernel.org/project/netdevbpf/cover/20210524131421.1030789-1-olteanv@gmail.com/

even though it isn't the first time these patches are submitted (they
were part of the group previously called "Add NXP SJA1110 support to the
sja1105 DSA driver"):
https://patchwork.kernel.org/project/netdevbpf/cover/20210526135535.2515123-1-vladimir.oltean@nxp.com/

but I broke that up again since these patches are already reviewed, for
the most part. There are no changes compared to v2 and v1.

This series of patches contains:

- an adaptation of the driver to the new "ethernet-ports" OF node name
- an adaptation of the driver to support more than 1 SGMII port
- a generalization of the supported phy_interface_t values per port
- an adaptation to encode SPEED_10, SPEED_100, SPEED_1000 into the
  hardware registers differently depending on switch revision
- a consolidation of the PHY interface type used for RGMII and another
  one for the API exposed for sja1105_dynamic_config_read()
====================

Link: https://lore.kernel.org/r/20210530225939.772553-1-olteanv@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

drivers/net/dsa/sja1105/sja1105.h

@@ -48,7 +48,6 @@ struct sja1105_regs {
 	u64 rgu;
 	u64 vl_status;
 	u64 config;
-	u64 sgmii;
 	u64 rmii_pll1;
 	u64 ptppinst;
 	u64 ptppindur;
@@ -73,6 +72,15 @@ struct sja1105_regs {
 	u64 stats[__MAX_SJA1105_STATS_AREA][SJA1105_MAX_NUM_PORTS];
 };
 
+enum {
+	SJA1105_SPEED_AUTO,
+	SJA1105_SPEED_10MBPS,
+	SJA1105_SPEED_100MBPS,
+	SJA1105_SPEED_1000MBPS,
+	SJA1105_SPEED_2500MBPS,
+	SJA1105_SPEED_MAX,
+};
+
 struct sja1105_info {
 	u64 device_id;
 	/* Needed for distinction between P and R, and between Q and S
@@ -112,6 +120,12 @@ struct sja1105_info {
 				enum packing_op op);
 	int (*clocking_setup)(struct sja1105_private *priv);
 	const char *name;
+	bool supports_mii[SJA1105_MAX_NUM_PORTS];
+	bool supports_rmii[SJA1105_MAX_NUM_PORTS];
+	bool supports_rgmii[SJA1105_MAX_NUM_PORTS];
+	bool supports_sgmii[SJA1105_MAX_NUM_PORTS];
+	bool supports_2500basex[SJA1105_MAX_NUM_PORTS];
+	const u64 port_speed[SJA1105_SPEED_MAX];
 };
 
 enum sja1105_key_type {
@@ -211,6 +225,7 @@ struct sja1105_private {
 	struct sja1105_static_config static_config;
 	bool rgmii_rx_delay[SJA1105_MAX_NUM_PORTS];
 	bool rgmii_tx_delay[SJA1105_MAX_NUM_PORTS];
+	phy_interface_t phy_mode[SJA1105_MAX_NUM_PORTS];
 	bool best_effort_vlan_filtering;
 	unsigned long learn_ena;
 	unsigned long ucast_egress_floods;
@@ -309,13 +324,6 @@ typedef enum {
 	XMII_MODE_SGMII		= 3,
 } sja1105_phy_interface_t;
 
-typedef enum {
-	SJA1105_SPEED_10MBPS	= 3,
-	SJA1105_SPEED_100MBPS	= 2,
-	SJA1105_SPEED_1000MBPS	= 1,
-	SJA1105_SPEED_AUTO	= 0,
-} sja1105_speed_t;
-
 int sja1105pqrs_setup_rgmii_delay(const void *ctx, int port);
 int sja1105_clocking_setup_port(struct sja1105_private *priv, int port);
 int sja1105_clocking_setup(struct sja1105_private *priv);

drivers/net/dsa/sja1105/sja1105_clocking.c

@@ -328,7 +328,7 @@ sja1105_cgu_pll_control_packing(void *buf, struct sja1105_cgu_pll_ctrl *cmd,
 }
 
 static int sja1105_cgu_rgmii_tx_clk_config(struct sja1105_private *priv,
-					   int port, sja1105_speed_t speed)
+					   int port, u64 speed)
 {
 	const struct sja1105_regs *regs = priv->info->regs;
 	struct sja1105_cgu_mii_ctrl txc;
@@ -338,7 +338,7 @@ static int sja1105_cgu_rgmii_tx_clk_config(struct sja1105_private *priv,
 	if (regs->rgmii_tx_clk[port] == SJA1105_RSV_ADDR)
 		return 0;
 
-	if (speed == SJA1105_SPEED_1000MBPS) {
+	if (speed == priv->info->port_speed[SJA1105_SPEED_1000MBPS]) {
 		clksrc = CLKSRC_PLL0;
 	} else {
 		int clk_sources[] = {CLKSRC_IDIV0, CLKSRC_IDIV1, CLKSRC_IDIV2,
@@ -524,35 +524,31 @@ static int sja1105_rgmii_clocking_setup(struct sja1105_private *priv, int port,
 {
 	struct device *dev = priv->ds->dev;
 	struct sja1105_mac_config_entry *mac;
-	sja1105_speed_t speed;
+	u64 speed;
 	int rc;
 
 	mac = priv->static_config.tables[BLK_IDX_MAC_CONFIG].entries;
 	speed = mac[port].speed;
 
-	dev_dbg(dev, "Configuring port %d RGMII at speed %dMbps\n",
+	dev_dbg(dev, "Configuring port %d RGMII at speed %lldMbps\n",
 		port, speed);
 
-	switch (speed) {
-	case SJA1105_SPEED_1000MBPS:
+	if (speed == priv->info->port_speed[SJA1105_SPEED_1000MBPS]) {
 		/* 1000Mbps, IDIV disabled (125 MHz) */
 		rc = sja1105_cgu_idiv_config(priv, port, false, 1);
-		break;
-	case SJA1105_SPEED_100MBPS:
+	} else if (speed == priv->info->port_speed[SJA1105_SPEED_100MBPS]) {
 		/* 100Mbps, IDIV enabled, divide by 1 (25 MHz) */
 		rc = sja1105_cgu_idiv_config(priv, port, true, 1);
-		break;
-	case SJA1105_SPEED_10MBPS:
+	} else if (speed == priv->info->port_speed[SJA1105_SPEED_10MBPS]) {
 		/* 10Mbps, IDIV enabled, divide by 10 (2.5 MHz) */
 		rc = sja1105_cgu_idiv_config(priv, port, true, 10);
-		break;
-	case SJA1105_SPEED_AUTO:
+	} else if (speed == priv->info->port_speed[SJA1105_SPEED_AUTO]) {
 		/* Skip CGU configuration if there is no speed available
 		 * (e.g. link is not established yet)
 		 */
 		dev_dbg(dev, "Speed not available, skipping CGU config\n");
 		return 0;
-	default:
+	} else {
 		rc = -EINVAL;
 	}
 
@@ -570,14 +566,9 @@ static int sja1105_rgmii_clocking_setup(struct sja1105_private *priv, int port,
 		dev_err(dev, "Failed to configure Tx pad registers\n");
 		return rc;
 	}
+
 	if (!priv->info->setup_rgmii_delay)
 		return 0;
-	/* The role has no hardware effect for RGMII. However we use it as
-	 * a proxy for this interface being a MAC-to-MAC connection, with
-	 * the RGMII internal delays needing to be applied by us.
-	 */
-	if (role == XMII_MAC)
-		return 0;
 
 	return priv->info->setup_rgmii_delay(priv, port);
 }

drivers/net/dsa/sja1105/sja1105_dynamic_config.c

@@ -78,6 +78,9 @@
  *		   on its ENTRY portion, as a result of a SPI write command.
  *		   Only the TCAM-based FDB table on SJA1105 P/Q/R/S supports
  *		   this.
+ *	OP_VALID_ANYWAY: Reading some tables through the dynamic config
+ *			 interface is possible even if the VALIDENT bit is not
+ *			 set in the writeback. So don't error out in that case.
  * - .max_entry_count: The number of entries, counting from zero, that can be
  *		       reconfigured through the dynamic interface. If a static
  *		       table can be reconfigured at all dynamically, this
@@ -651,6 +654,7 @@ static size_t sja1105pqrs_cbs_entry_packing(void *buf, void *entry_ptr,
 #define OP_WRITE	BIT(1)
 #define OP_DEL		BIT(2)
 #define OP_SEARCH	BIT(3)
+#define OP_VALID_ANYWAY	BIT(4)
 
 /* SJA1105E/T: First generation */
 const struct sja1105_dynamic_table_ops sja1105et_dyn_ops[BLK_IDX_MAX_DYN] = {
@@ -673,7 +677,7 @@ const struct sja1105_dynamic_table_ops sja1105et_dyn_ops[BLK_IDX_MAX_DYN] = {
 	[BLK_IDX_MGMT_ROUTE] = {
 		.entry_packing = sja1105et_mgmt_route_entry_packing,
 		.cmd_packing = sja1105et_mgmt_route_cmd_packing,
-		.access = (OP_READ | OP_WRITE),
+		.access = (OP_READ | OP_WRITE | OP_VALID_ANYWAY),
 		.max_entry_count = SJA1105_NUM_PORTS,
 		.packed_size = SJA1105ET_SIZE_L2_LOOKUP_DYN_CMD,
 		.addr = 0x20,
@@ -757,7 +761,7 @@ const struct sja1105_dynamic_table_ops sja1105pqrs_dyn_ops[BLK_IDX_MAX_DYN] = {
 	[BLK_IDX_MGMT_ROUTE] = {
 		.entry_packing = sja1105pqrs_mgmt_route_entry_packing,
 		.cmd_packing = sja1105pqrs_mgmt_route_cmd_packing,
-		.access = (OP_READ | OP_WRITE | OP_DEL | OP_SEARCH),
+		.access = (OP_READ | OP_WRITE | OP_DEL | OP_SEARCH | OP_VALID_ANYWAY),
 		.max_entry_count = SJA1105_NUM_PORTS,
 		.packed_size = SJA1105PQRS_SIZE_L2_LOOKUP_DYN_CMD,
 		.addr = 0x24,
@@ -911,11 +915,8 @@ int sja1105_dynamic_config_read(struct sja1105_private *priv,
 
 		cmd = (struct sja1105_dyn_cmd) {0};
 		ops->cmd_packing(packed_buf, &cmd, UNPACK);
-		/* UM10944: [valident] will always be found cleared
-		 * during a read access with MGMTROUTE set.
-		 * So don't error out in that case.
-		 */
-		if (!cmd.valident && blk_idx != BLK_IDX_MGMT_ROUTE)
+
+		if (!cmd.valident && !(ops->access & OP_VALID_ANYWAY))
 			return -ENOENT;
 		cpu_relax();
 	} while (cmd.valid && --retries);

drivers/net/dsa/sja1105/sja1105_spi.c

@@ -440,7 +440,6 @@ static struct sja1105_regs sja1105pqrs_regs = {
 	.pad_mii_tx = {0x100800, 0x100802, 0x100804, 0x100806, 0x100808},
 	.pad_mii_rx = {0x100801, 0x100803, 0x100805, 0x100807, 0x100809},
 	.pad_mii_id = {0x100810, 0x100811, 0x100812, 0x100813, 0x100814},
-	.sgmii = 0x1F0000,
 	.rmii_pll1 = 0x10000A,
 	.cgu_idiv = {0x10000B, 0x10000C, 0x10000D, 0x10000E, 0x10000F},
 	.stats[MAC] = {0x200, 0x202, 0x204, 0x206, 0x208},
@@ -483,6 +482,16 @@ const struct sja1105_info sja1105e_info = {
 	.ptp_cmd_packing	= sja1105et_ptp_cmd_packing,
 	.clocking_setup		= sja1105_clocking_setup,
 	.regs			= &sja1105et_regs,
+	.port_speed		= {
+		[SJA1105_SPEED_AUTO] = 0,
+		[SJA1105_SPEED_10MBPS] = 3,
+		[SJA1105_SPEED_100MBPS] = 2,
+		[SJA1105_SPEED_1000MBPS] = 1,
+		[SJA1105_SPEED_2500MBPS] = 0, /* Not supported */
+	},
+	.supports_mii		= {true, true, true, true, true},
+	.supports_rmii		= {true, true, true, true, true},
+	.supports_rgmii		= {true, true, true, true, true},
 	.name			= "SJA1105E",
 };
 
@@ -503,6 +512,16 @@ const struct sja1105_info sja1105t_info = {
 	.ptp_cmd_packing	= sja1105et_ptp_cmd_packing,
 	.clocking_setup		= sja1105_clocking_setup,
 	.regs			= &sja1105et_regs,
+	.port_speed		= {
+		[SJA1105_SPEED_AUTO] = 0,
+		[SJA1105_SPEED_10MBPS] = 3,
+		[SJA1105_SPEED_100MBPS] = 2,
+		[SJA1105_SPEED_1000MBPS] = 1,
+		[SJA1105_SPEED_2500MBPS] = 0, /* Not supported */
+	},
+	.supports_mii		= {true, true, true, true, true},
+	.supports_rmii		= {true, true, true, true, true},
+	.supports_rgmii		= {true, true, true, true, true},
 	.name			= "SJA1105T",
 };
 
@@ -524,6 +543,16 @@ const struct sja1105_info sja1105p_info = {
 	.ptp_cmd_packing	= sja1105pqrs_ptp_cmd_packing,
 	.clocking_setup		= sja1105_clocking_setup,
 	.regs			= &sja1105pqrs_regs,
+	.port_speed		= {
+		[SJA1105_SPEED_AUTO] = 0,
+		[SJA1105_SPEED_10MBPS] = 3,
+		[SJA1105_SPEED_100MBPS] = 2,
+		[SJA1105_SPEED_1000MBPS] = 1,
+		[SJA1105_SPEED_2500MBPS] = 0, /* Not supported */
+	},
+	.supports_mii		= {true, true, true, true, true},
+	.supports_rmii		= {true, true, true, true, true},
+	.supports_rgmii		= {true, true, true, true, true},
 	.name			= "SJA1105P",
 };
 
@@ -545,6 +574,16 @@ const struct sja1105_info sja1105q_info = {
 	.ptp_cmd_packing	= sja1105pqrs_ptp_cmd_packing,
 	.clocking_setup		= sja1105_clocking_setup,
 	.regs			= &sja1105pqrs_regs,
+	.port_speed		= {
+		[SJA1105_SPEED_AUTO] = 0,
+		[SJA1105_SPEED_10MBPS] = 3,
+		[SJA1105_SPEED_100MBPS] = 2,
+		[SJA1105_SPEED_1000MBPS] = 1,
+		[SJA1105_SPEED_2500MBPS] = 0, /* Not supported */
+	},
+	.supports_mii		= {true, true, true, true, true},
+	.supports_rmii		= {true, true, true, true, true},
+	.supports_rgmii		= {true, true, true, true, true},
 	.name			= "SJA1105Q",
 };
 
@@ -566,6 +605,17 @@ const struct sja1105_info sja1105r_info = {
 	.ptp_cmd_packing	= sja1105pqrs_ptp_cmd_packing,
 	.clocking_setup		= sja1105_clocking_setup,
 	.regs			= &sja1105pqrs_regs,
+	.port_speed		= {
+		[SJA1105_SPEED_AUTO] = 0,
+		[SJA1105_SPEED_10MBPS] = 3,
+		[SJA1105_SPEED_100MBPS] = 2,
+		[SJA1105_SPEED_1000MBPS] = 1,
+		[SJA1105_SPEED_2500MBPS] = 0, /* Not supported */
+	},
+	.supports_mii		= {true, true, true, true, true},
+	.supports_rmii		= {true, true, true, true, true},
+	.supports_rgmii		= {true, true, true, true, true},
+	.supports_sgmii		= {false, false, false, false, true},
 	.name			= "SJA1105R",
 };
 
@@ -587,5 +637,16 @@ const struct sja1105_info sja1105s_info = {
 	.fdb_del_cmd		= sja1105pqrs_fdb_del,
 	.ptp_cmd_packing	= sja1105pqrs_ptp_cmd_packing,
 	.clocking_setup		= sja1105_clocking_setup,
+	.port_speed		= {
+		[SJA1105_SPEED_AUTO] = 0,
+		[SJA1105_SPEED_10MBPS] = 3,
+		[SJA1105_SPEED_100MBPS] = 2,
+		[SJA1105_SPEED_1000MBPS] = 1,
+		[SJA1105_SPEED_2500MBPS] = 0, /* Not supported */
+	},
+	.supports_mii		= {true, true, true, true, true},
+	.supports_rmii		= {true, true, true, true, true},
+	.supports_rgmii		= {true, true, true, true, true},
+	.supports_sgmii		= {false, false, false, false, true},
 	.name			= "SJA1105S",
 };