Commit e555e5b1 authored by Maxime Chevallier's avatar Maxime Chevallier Committed by David S. Miller

net: phy: marvell10g: Use 2500BASEX when using 2.5GBASET

The Marvell Alaska family of PHYs supports 2.5GBaseT and 5GBaseT modes,
as defined in the 802.3bz specification.

Upon establishing a 2.5GBASET link, the PHY will reconfigure it's MII
interface to 2500BASEX.

At 5G, the PHY will reconfigure it's interface to 5GBASE-R, but this
mode isn't supported by any MAC for now.

This was tested with :
 - The 88X3310, which is on the MacchiatoBin
 - The 88E2010, an Alaska PHY that has no fiber interfaces, and is
   limited to 5G maximum speed.
Signed-off-by: default avatarMaxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 0feaccd5
...@@ -235,6 +235,7 @@ static int mv3310_config_init(struct phy_device *phydev) ...@@ -235,6 +235,7 @@ static int mv3310_config_init(struct phy_device *phydev)
{ {
/* Check that the PHY interface type is compatible */ /* Check that the PHY interface type is compatible */
if (phydev->interface != PHY_INTERFACE_MODE_SGMII && if (phydev->interface != PHY_INTERFACE_MODE_SGMII &&
phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
phydev->interface != PHY_INTERFACE_MODE_XAUI && phydev->interface != PHY_INTERFACE_MODE_XAUI &&
phydev->interface != PHY_INTERFACE_MODE_RXAUI && phydev->interface != PHY_INTERFACE_MODE_RXAUI &&
phydev->interface != PHY_INTERFACE_MODE_10GKR) phydev->interface != PHY_INTERFACE_MODE_10GKR)
...@@ -313,18 +314,29 @@ static int mv3310_aneg_done(struct phy_device *phydev) ...@@ -313,18 +314,29 @@ static int mv3310_aneg_done(struct phy_device *phydev)
static void mv3310_update_interface(struct phy_device *phydev) static void mv3310_update_interface(struct phy_device *phydev)
{ {
if ((phydev->interface == PHY_INTERFACE_MODE_SGMII || if ((phydev->interface == PHY_INTERFACE_MODE_SGMII ||
phydev->interface == PHY_INTERFACE_MODE_2500BASEX ||
phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) { phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) {
/* The PHY automatically switches its serdes interface (and /* The PHY automatically switches its serdes interface (and
* active PHYXS instance) between Cisco SGMII and 10GBase-KR * active PHYXS instance) between Cisco SGMII, 10GBase-KR and
* modes according to the speed. Florian suggests setting * 2500BaseX modes according to the speed. Florian suggests
* phydev->interface to communicate this to the MAC. Only do * setting phydev->interface to communicate this to the MAC.
* this if we are already in either SGMII or 10GBase-KR mode. * Only do this if we are already in one of the above modes.
*/ */
if (phydev->speed == SPEED_10000) switch (phydev->speed) {
case SPEED_10000:
phydev->interface = PHY_INTERFACE_MODE_10GKR; phydev->interface = PHY_INTERFACE_MODE_10GKR;
else if (phydev->speed >= SPEED_10 && break;
phydev->speed < SPEED_10000) case SPEED_2500:
phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
break;
case SPEED_1000:
case SPEED_100:
case SPEED_10:
phydev->interface = PHY_INTERFACE_MODE_SGMII; phydev->interface = PHY_INTERFACE_MODE_SGMII;
break;
default:
break;
}
} }
} }
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment