USB: check port changes before hub runtime suspend for some bug device

The hub status endpoint has a long 'bInterval', which is 255ms
for FS/LS device and 256ms for HS device according to USB 2.0 spec,
so the device connection change may be reported later more than 255ms
via status pipe.

The connection change in hub may have been happened already on the
downstream ports, but no status URB completes when it is killed
in hub_suspend(auto), so the connection change may be missed by some
buggy hub devices, which won't generate remote wakeup signal after
their remote wakeup is enabled and they are put into suspend state.

The problem can be observed at least on the below Genesys Logic, Inc.
hub devices:

	0x05e3,0x0606
	0x05e3,0x0608

In theory, there is no way to fix the problem completely, but we
can make it less likely to occur by this patch.

This patch introduces one quirk of HUB_QUIRK_CHECK_PORTS_AUTOSUSPEND
to check ports' change during hub_suspend(auto) for the buggy
devices. If ports' change is found, terminate the auto suspend and
return to working state.

So for the buggy hubs, if the connection change happend before
the ports' check, it can be handled correctly. If it happens between
the ports' check and enabling remote wakeup/entering suspend, it
will be missed. Considered the interval is quite short, it is very
less likely to happen during the window.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/core/hub.c

@@ -39,6 +39,9 @@
 #endif
 #endif
 
+#define USB_VENDOR_GENESYS_LOGIC		0x05e3
+#define HUB_QUIRK_CHECK_PORT_AUTOSUSPEND	0x01
+
 struct usb_port {
 	struct usb_device *child;
 	struct device dev;
@@ -86,6 +89,8 @@ struct usb_hub {
 	unsigned		quiescing:1;
 	unsigned		disconnected:1;
 
+	unsigned		quirk_check_port_auto_suspend:1;
+
 	unsigned		has_indicators:1;
 	u8			indicator[USB_MAXCHILDREN];
 	struct delayed_work	leds;
@@ -1667,6 +1672,9 @@ static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id)
 	if (hdev->speed == USB_SPEED_HIGH)
 		highspeed_hubs++;
 
+	if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
+		hub->quirk_check_port_auto_suspend = 1;
+
 	if (hub_configure(hub, endpoint) >= 0)
 		return 0;
 
@@ -3125,6 +3133,21 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg)
 
 #endif
 
+static int check_ports_changed(struct usb_hub *hub)
+{
+	int port1;
+
+	for (port1 = 1; port1 <= hub->hdev->maxchild; ++port1) {
+		u16 portstatus, portchange;
+		int status;
+
+		status = hub_port_status(hub, port1, &portstatus, &portchange);
+		if (!status && portchange)
+			return 1;
+	}
+	return 0;
+}
+
 static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
 {
 	struct usb_hub		*hub = usb_get_intfdata (intf);
@@ -3143,6 +3166,16 @@ static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
 				return -EBUSY;
 		}
 	}
+
+	if (hdev->do_remote_wakeup && hub->quirk_check_port_auto_suspend) {
+		/* check if there are changes pending on hub ports */
+		if (check_ports_changed(hub)) {
+			if (PMSG_IS_AUTO(msg))
+				return -EBUSY;
+			pm_wakeup_event(&hdev->dev, 2000);
+		}
+	}
+
 	if (hub_is_superspeed(hdev) && hdev->do_remote_wakeup) {
 		/* Enable hub to send remote wakeup for all ports. */
 		for (port1 = 1; port1 <= hdev->maxchild; port1++) {
@@ -4647,6 +4680,11 @@ static int hub_thread(void *__unused)
 }
 
 static const struct usb_device_id hub_id_table[] = {
+    { .match_flags = USB_DEVICE_ID_MATCH_VENDOR
+	           | USB_DEVICE_ID_MATCH_INT_CLASS,
+      .idVendor = USB_VENDOR_GENESYS_LOGIC,
+      .bInterfaceClass = USB_CLASS_HUB,
+      .driver_info = HUB_QUIRK_CHECK_PORT_AUTOSUSPEND},
     { .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS,
       .bDeviceClass = USB_CLASS_HUB},
     { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS,