Commit e92a4047 authored by Stephen Boyd's avatar Stephen Boyd Committed by Mark Brown

regulator: Add QCOM SPMI regulator driver

Add an SPMI regulator driver for Qualcomm's PM8841, PM8941, and
PM8916 PMICs. This driver is based largely on code from
codeaurora.org[1].

[1] https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.10/tree/drivers/regulator/qpnp-regulator.c?h=msm-3.10
Cc: David Collins <collinsd@codeaurora.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: default avatarStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: default avatarMark Brown <broonie@kernel.org>
parent b787f68c
Qualcomm SPMI Regulators
- compatible:
Usage: required
Value type: <string>
Definition: must be one of:
"qcom,pm8841-regulators"
"qcom,pm8916-regulators"
"qcom,pm8941-regulators"
- interrupts:
Usage: optional
Value type: <prop-encoded-array>
Definition: List of OCP interrupts.
- interrupt-names:
Usage: required if 'interrupts' property present
Value type: <string-array>
Definition: List of strings defining the names of the
interrupts in the 'interrupts' property 1-to-1.
Supported values are "ocp-<regulator_name>", where
<regulator_name> corresponds to a voltage switch
type regulator.
- vdd_s1-supply:
- vdd_s2-supply:
- vdd_s3-supply:
- vdd_s4-supply:
- vdd_s5-supply:
- vdd_s6-supply:
- vdd_s7-supply:
- vdd_s8-supply:
Usage: optional (pm8841 only)
Value type: <phandle>
Definition: Reference to regulator supplying the input pin, as
described in the data sheet.
- vdd_s1-supply:
- vdd_s2-supply:
- vdd_s3-supply:
- vdd_s4-supply:
- vdd_l1_l3-supply:
- vdd_l2-supply:
- vdd_l4_l5_l6-supply:
- vdd_l7-supply:
- vdd_l8_l11_l14_l15_l16-supply:
- vdd_l9_l10_l12_l13_l17_l18-supply:
Usage: optional (pm8916 only)
Value type: <phandle>
Definition: Reference to regulator supplying the input pin, as
described in the data sheet.
- vdd_s1-supply:
- vdd_s2-supply:
- vdd_s3-supply:
- vdd_l1_l3-supply:
- vdd_l2_lvs_1_2_3-supply:
- vdd_l4_l11-supply:
- vdd_l5_l7-supply:
- vdd_l6_l12_l14_l15-supply:
- vdd_l8_l16_l18_19-supply:
- vdd_l9_l10_l17_l22-supply:
- vdd_l13_l20_l23_l24-supply:
- vdd_l21-supply:
- vin_5vs-supply:
Usage: optional (pm8941 only)
Value type: <phandle>
Definition: Reference to regulator supplying the input pin, as
described in the data sheet.
The regulator node houses sub-nodes for each regulator within the device. Each
sub-node is identified using the node's name, with valid values listed for each
of the PMICs below.
pm8841:
s1, s2, s3, s4, s5, s6, s7, s8
pm8916:
s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
l14, l15, l16, l17, l18
pm8941:
s1, s2, s3, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14,
l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
mvs1, mvs2
The content of each sub-node is defined by the standard binding for regulators -
see regulator.txt - with additional custom properties described below:
- regulator-initial-mode:
Usage: optional
Value type: <u32>
Descrption: 1 = Set initial mode to high power mode (HPM), also referred
to as NPM. HPM consumes more ground current than LPM, but
it can source significantly higher load current. HPM is not
available on boost type regulators. For voltage switch type
regulators, HPM implies that over current protection and
soft start are active all the time. 0 = Set initial mode to
low power mode (LPM).
Example:
regulators {
compatible = "qcom,pm8941-regulators";
vdd_l1_l3-supply = <&s1>;
s1: s1 {
regulator-min-microvolt = <1300000>;
regulator-max-microvolt = <1400000>;
};
...
l1: l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1300000>;
};
....
};
......@@ -512,6 +512,17 @@ config REGULATOR_QCOM_RPM
Qualcomm RPM as a module. The module will be named
"qcom_rpm-regulator".
config REGULATOR_QCOM_SPMI
tristate "Qualcomm SPMI regulator driver"
depends on SPMI || COMPILE_TEST
help
If you say yes to this option, support will be included for the
regulators found in Qualcomm SPMI PMICs.
Say M here if you want to include support for the regulators on the
Qualcomm SPMI PMICs as a module. The module will be named
"qcom_spmi-regulator".
config REGULATOR_RC5T583
tristate "RICOH RC5T583 Power regulators"
depends on MFD_RC5T583
......
......@@ -61,6 +61,7 @@ obj-$(CONFIG_REGULATOR_MC13892) += mc13892-regulator.o
obj-$(CONFIG_REGULATOR_MC13XXX_CORE) += mc13xxx-regulator-core.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_RPM) += qcom_rpm-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_SPMI) += qcom_spmi-regulator.o
obj-$(CONFIG_REGULATOR_PALMAS) += palmas-regulator.o
obj-$(CONFIG_REGULATOR_PFUZE100) += pfuze100-regulator.o
obj-$(CONFIG_REGULATOR_PWM) += pwm-regulator.o
......
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment