hwmon: Driver for Texas Instruments INA238

The INA238 is a I2C power monitor similar to other INA2xx devices,
providing shunt voltage, bus voltage, current, power and temperature
measurements.
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Link: https://lore.kernel.org/r/20211102052754.817220-3-nathan@nathanrossi.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Documentation/hwmon/ina238.rst

+.. SPDX-License-Identifier: GPL-2.0-only
+
+Kernel driver ina238
+====================
+
+Supported chips:
+
+  * Texas Instruments INA238
+
+    Prefix: 'ina238'
+
+    Addresses: I2C 0x40 - 0x4f
+
+    Datasheet:
+	https://www.ti.com/lit/gpn/ina238
+
+Author: Nathan Rossi <nathan.rossi@digi.com>
+
+Description
+-----------
+
+The INA238 is a current shunt, power and temperature monitor with an I2C
+interface. It includes a number of programmable functions including alerts,
+conversion rate, sample averaging and selectable shunt voltage accuracy.
+
+The shunt value in micro-ohms can be set via platform data or device tree at
+compile-time or via the shunt_resistor attribute in sysfs at run-time. Please
+refer to the Documentation/devicetree/bindings/hwmon/ti,ina2xx.yaml for bindings
+if the device tree is used.
+
+Sysfs entries
+-------------
+
+======================= =======================================================
+in0_input		Shunt voltage (mV)
+in0_min			Minimum shunt voltage threshold (mV)
+in0_min_alarm		Minimum shunt voltage alarm
+in0_max			Maximum shunt voltage threshold (mV)
+in0_max_alarm		Maximum shunt voltage alarm
+
+in1_input		Bus voltage (mV)
+in1_min			Minimum bus voltage threshold (mV)
+in1_min_alarm		Minimum shunt voltage alarm
+in1_max			Maximum bus voltage threshold (mV)
+in1_max_alarm		Maximum shunt voltage alarm
+
+power1_input		Power measurement (uW)
+power1_max		Maximum power threshold (uW)
+power1_max_alarm	Maximum power alarm
+
+curr1_input		Current measurement (mA)
+
+temp1_input		Die temperature measurement (mC)
+temp1_max		Maximum die temperature threshold (mC)
+temp1_max_alarm		Maximum die temperature alarm
+======================= =======================================================

Documentation/hwmon/index.rst

@@ -76,6 +76,7 @@ Hardware Monitoring Kernel Drivers
    ibmpowernv
    ina209
    ina2xx
+   ina238
    ina3221
    intel-m10-bmc-hwmon
    ir35221

drivers/hwmon/Kconfig

@@ -1872,6 +1872,18 @@ config SENSORS_INA2XX
 	  This driver can also be built as a module. If so, the module
 	  will be called ina2xx.
 
+config SENSORS_INA238
+	tristate "Texas Instruments INA238"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  If you say yes here you get support for the INA238 power monitor
+	  chip. This driver supports voltage, current, power and temperature
+	  measurements as well as alarm configuration.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called ina238.
+
 config SENSORS_INA3221
 	tristate "Texas Instruments INA3221 Triple Power Monitor"
 	depends on I2C

drivers/hwmon/Makefile

@@ -90,6 +90,7 @@ obj-$(CONFIG_SENSORS_IBMPOWERNV)+= ibmpowernv.o
 obj-$(CONFIG_SENSORS_IIO_HWMON) += iio_hwmon.o
 obj-$(CONFIG_SENSORS_INA209)	+= ina209.o
 obj-$(CONFIG_SENSORS_INA2XX)	+= ina2xx.o
+obj-$(CONFIG_SENSORS_INA238)	+= ina238.o
 obj-$(CONFIG_SENSORS_INA3221)	+= ina3221.o
 obj-$(CONFIG_SENSORS_INTEL_M10_BMC_HWMON) += intel-m10-bmc-hwmon.o
 obj-$(CONFIG_SENSORS_IT87)	+= it87.o