MIPS: Yeeloong 2F: Add basic EC operations

YeeLoong2F has a KB3310b embedded controller. Add basic operations for
future related drivers and board support.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/684/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/loongson/lemote-2f/Makefile

@@ -2,7 +2,7 @@
 # Makefile for lemote loongson2f family machines
 #
 
-obj-y += irq.o reset.o
+obj-y += irq.o reset.o ec_kb3310b.o
 
 #
 # Suspend Support

arch/mips/loongson/lemote-2f/ec_kb3310b.c

+/*
+ * Basic KB3310B Embedded Controller support for the YeeLoong 2F netbook
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-04-20
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/spinlock.h>
+#include <linux/delay.h>
+
+#include "ec_kb3310b.h"
+
+static DEFINE_SPINLOCK(index_access_lock);
+static DEFINE_SPINLOCK(port_access_lock);
+
+unsigned char ec_read(unsigned short addr)
+{
+	unsigned char value;
+	unsigned long flags;
+
+	spin_lock_irqsave(&index_access_lock, flags);
+	outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
+	outb((addr & 0x00ff), EC_IO_PORT_LOW);
+	value = inb(EC_IO_PORT_DATA);
+	spin_unlock_irqrestore(&index_access_lock, flags);
+
+	return value;
+}
+EXPORT_SYMBOL_GPL(ec_read);
+
+void ec_write(unsigned short addr, unsigned char val)
+{
+	unsigned long flags;
+
+	spin_lock_irqsave(&index_access_lock, flags);
+	outb((addr & 0xff00) >> 8, EC_IO_PORT_HIGH);
+	outb((addr & 0x00ff), EC_IO_PORT_LOW);
+	outb(val, EC_IO_PORT_DATA);
+	/*  flush the write action */
+	inb(EC_IO_PORT_DATA);
+	spin_unlock_irqrestore(&index_access_lock, flags);
+
+	return;
+}
+EXPORT_SYMBOL_GPL(ec_write);
+
+/*
+ * This function is used for EC command writes and corresponding status queries.
+ */
+int ec_query_seq(unsigned char cmd)
+{
+	int timeout;
+	unsigned char status;
+	unsigned long flags;
+	int ret = 0;
+
+	spin_lock_irqsave(&port_access_lock, flags);
+
+	/* make chip goto reset mode */
+	udelay(EC_REG_DELAY);
+	outb(cmd, EC_CMD_PORT);
+	udelay(EC_REG_DELAY);
+
+	/* check if the command is received by ec */
+	timeout = EC_CMD_TIMEOUT;
+	status = inb(EC_STS_PORT);
+	while (timeout-- && (status & (1 << 1))) {
+		status = inb(EC_STS_PORT);
+		udelay(EC_REG_DELAY);
+	}
+
+	if (timeout <= 0) {
+		printk(KERN_ERR "%s: deadable error : timeout...\n", __func__);
+		ret = -EINVAL;
+	} else
+		printk(KERN_INFO
+			   "(%x/%d)ec issued command %d status : 0x%x\n",
+			   timeout, EC_CMD_TIMEOUT - timeout, cmd, status);
+
+	spin_unlock_irqrestore(&port_access_lock, flags);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(ec_query_seq);
+
+/*
+ * Send query command to EC to get the proper event number
+ */
+int ec_query_event_num(void)
+{
+	return ec_query_seq(CMD_GET_EVENT_NUM);
+}
+EXPORT_SYMBOL(ec_query_event_num);
+
+/*
+ * Get event number from EC
+ *
+ * NOTE: This routine must follow the query_event_num function in the
+ * interrupt.
+ */
+int ec_get_event_num(void)
+{
+	int timeout = 100;
+	unsigned char value;
+	unsigned char status;
+
+	udelay(EC_REG_DELAY);
+	status = inb(EC_STS_PORT);
+	udelay(EC_REG_DELAY);
+	while (timeout-- && !(status & (1 << 0))) {
+		status = inb(EC_STS_PORT);
+		udelay(EC_REG_DELAY);
+	}
+	if (timeout <= 0) {
+		pr_info("%s: get event number timeout.\n", __func__);
+
+		return -EINVAL;
+	}
+	value = inb(EC_DAT_PORT);
+	udelay(EC_REG_DELAY);
+
+	return value;
+}
+EXPORT_SYMBOL(ec_get_event_num);

arch/mips/loongson/lemote-2f/ec_kb3310b.h

+/*
+ * KB3310B Embedded Controller
+ *
+ *  Copyright (C) 2008 Lemote Inc.
+ *  Author: liujl <liujl@lemote.com>, 2008-03-14
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _EC_KB3310B_H
+#define _EC_KB3310B_H
+
+extern unsigned char ec_read(unsigned short addr);
+extern void ec_write(unsigned short addr, unsigned char val);
+extern int ec_query_seq(unsigned char cmd);
+extern int ec_query_event_num(void);
+extern int ec_get_event_num(void);
+
+typedef int (*sci_handler) (int status);
+extern sci_handler yeeloong_report_lid_status;
+
+#define SCI_IRQ_NUM 0x0A
+
+/*
+ * The following registers are determined by the EC index configuration.
+ * 1, fill the PORT_HIGH as EC register high part.
+ * 2, fill the PORT_LOW as EC register low part.
+ * 3, fill the PORT_DATA as EC register write data or get the data from it.
+ */
+#define	EC_IO_PORT_HIGH	0x0381
+#define	EC_IO_PORT_LOW	0x0382
+#define	EC_IO_PORT_DATA	0x0383
+
+/*
+ * EC delay time is 500us for register and status access
+ */
+#define	EC_REG_DELAY	500	/* unit : us */
+#define	EC_CMD_TIMEOUT	0x1000
+
+/*
+ * EC access port for SCI communication
+ */
+#define	EC_CMD_PORT		0x66
+#define	EC_STS_PORT		0x66
+#define	EC_DAT_PORT		0x62
+#define	CMD_INIT_IDLE_MODE	0xdd
+#define	CMD_EXIT_IDLE_MODE	0xdf
+#define	CMD_INIT_RESET_MODE	0xd8
+#define	CMD_REBOOT_SYSTEM	0x8c
+#define	CMD_GET_EVENT_NUM	0x84
+#define	CMD_PROGRAM_PIECE	0xda
+
+/* temperature & fan registers */
+#define	REG_TEMPERATURE_VALUE	0xF458
+#define	REG_FAN_AUTO_MAN_SWITCH 0xF459
+#define	BIT_FAN_AUTO		0
+#define	BIT_FAN_MANUAL		1
+#define	REG_FAN_CONTROL		0xF4D2
+#define	BIT_FAN_CONTROL_ON	(1 << 0)
+#define	BIT_FAN_CONTROL_OFF	(0 << 0)
+#define	REG_FAN_STATUS		0xF4DA
+#define	BIT_FAN_STATUS_ON	(1 << 0)
+#define	BIT_FAN_STATUS_OFF	(0 << 0)
+#define	REG_FAN_SPEED_HIGH	0xFE22
+#define	REG_FAN_SPEED_LOW	0xFE23
+#define	REG_FAN_SPEED_LEVEL	0xF4CC
+/* fan speed divider */
+#define	FAN_SPEED_DIVIDER	480000	/* (60*1000*1000/62.5/2)*/
+
+/* battery registers */
+#define	REG_BAT_DESIGN_CAP_HIGH		0xF77D
+#define	REG_BAT_DESIGN_CAP_LOW		0xF77E
+#define	REG_BAT_FULLCHG_CAP_HIGH	0xF780
+#define	REG_BAT_FULLCHG_CAP_LOW		0xF781
+#define	REG_BAT_DESIGN_VOL_HIGH		0xF782
+#define	REG_BAT_DESIGN_VOL_LOW		0xF783
+#define	REG_BAT_CURRENT_HIGH		0xF784
+#define	REG_BAT_CURRENT_LOW		0xF785
+#define	REG_BAT_VOLTAGE_HIGH		0xF786
+#define	REG_BAT_VOLTAGE_LOW		0xF787
+#define	REG_BAT_TEMPERATURE_HIGH	0xF788
+#define	REG_BAT_TEMPERATURE_LOW		0xF789
+#define	REG_BAT_RELATIVE_CAP_HIGH	0xF492
+#define	REG_BAT_RELATIVE_CAP_LOW	0xF493
+#define	REG_BAT_VENDOR			0xF4C4
+#define	FLAG_BAT_VENDOR_SANYO		0x01
+#define	FLAG_BAT_VENDOR_SIMPLO		0x02
+#define	REG_BAT_CELL_COUNT		0xF4C6
+#define	FLAG_BAT_CELL_3S1P		0x03
+#define	FLAG_BAT_CELL_3S2P		0x06
+#define	REG_BAT_CHARGE			0xF4A2
+#define	FLAG_BAT_CHARGE_DISCHARGE	0x01
+#define	FLAG_BAT_CHARGE_CHARGE		0x02
+#define	FLAG_BAT_CHARGE_ACPOWER		0x00
+#define	REG_BAT_STATUS			0xF4B0
+#define	BIT_BAT_STATUS_LOW		(1 << 5)
+#define	BIT_BAT_STATUS_DESTROY		(1 << 2)
+#define	BIT_BAT_STATUS_FULL		(1 << 1)
+#define	BIT_BAT_STATUS_IN		(1 << 0)
+#define	REG_BAT_CHARGE_STATUS		0xF4B1
+#define	BIT_BAT_CHARGE_STATUS_OVERTEMP	(1 << 2)
+#define	BIT_BAT_CHARGE_STATUS_PRECHG	(1 << 1)
+#define	REG_BAT_STATE			0xF482
+#define	BIT_BAT_STATE_CHARGING		(1 << 1)
+#define	BIT_BAT_STATE_DISCHARGING	(1 << 0)
+#define	REG_BAT_POWER			0xF440
+#define	BIT_BAT_POWER_S3		(1 << 2)
+#define	BIT_BAT_POWER_ON		(1 << 1)
+#define	BIT_BAT_POWER_ACIN		(1 << 0)
+
+/* other registers */
+/* Audio: rd/wr */
+#define	REG_AUDIO_VOLUME	0xF46C
+#define	REG_AUDIO_MUTE		0xF4E7
+#define	REG_AUDIO_BEEP		0xF4D0
+/* USB port power or not: rd/wr */
+#define	REG_USB0_FLAG		0xF461
+#define	REG_USB1_FLAG		0xF462
+#define	REG_USB2_FLAG		0xF463
+#define	BIT_USB_FLAG_ON		1
+#define	BIT_USB_FLAG_OFF	0
+/* LID */
+#define	REG_LID_DETECT		0xF4BD
+#define	BIT_LID_DETECT_ON	1
+#define	BIT_LID_DETECT_OFF	0
+/* CRT */
+#define	REG_CRT_DETECT		0xF4AD
+#define	BIT_CRT_DETECT_PLUG	1
+#define	BIT_CRT_DETECT_UNPLUG	0
+/* LCD backlight brightness adjust: 9 levels */
+#define	REG_DISPLAY_BRIGHTNESS	0xF4F5
+/* Black screen Status */
+#define	BIT_DISPLAY_LCD_ON	1
+#define	BIT_DISPLAY_LCD_OFF	0
+/* LCD backlight control: off/restore */
+#define	REG_BACKLIGHT_CTRL	0xF7BD
+#define	BIT_BACKLIGHT_ON	1
+#define	BIT_BACKLIGHT_OFF	0
+/* Reset the machine auto-clear: rd/wr */
+#define	REG_RESET		0xF4EC
+#define	BIT_RESET_ON		1
+/* Light the led: rd/wr */
+#define	REG_LED			0xF4C8
+#define	BIT_LED_RED_POWER	(1 << 0)
+#define	BIT_LED_ORANGE_POWER	(1 << 1)
+#define	BIT_LED_GREEN_CHARGE	(1 << 2)
+#define	BIT_LED_RED_CHARGE	(1 << 3)
+#define	BIT_LED_NUMLOCK		(1 << 4)
+/* Test led mode, all led on/off */
+#define	REG_LED_TEST		0xF4C2
+#define	BIT_LED_TEST_IN		1
+#define	BIT_LED_TEST_OUT	0
+/* Camera on/off */
+#define	REG_CAMERA_STATUS	0xF46A
+#define	BIT_CAMERA_STATUS_ON	1
+#define	BIT_CAMERA_STATUS_OFF	0
+#define	REG_CAMERA_CONTROL	0xF7B7
+#define	BIT_CAMERA_CONTROL_OFF	0
+#define	BIT_CAMERA_CONTROL_ON	1
+/* Wlan Status */
+#define	REG_WLAN		0xF4FA
+#define	BIT_WLAN_ON		1
+#define	BIT_WLAN_OFF		0
+#define	REG_DISPLAY_LCD		0xF79F
+
+/* SCI Event Number from EC */
+enum {
+	EVENT_LID = 0x23,	/*  LID open/close */
+	EVENT_DISPLAY_TOGGLE,	/*  Fn+F3 for display switch */
+	EVENT_SLEEP,		/*  Fn+F1 for entering sleep mode */
+	EVENT_OVERTEMP,		/*  Over-temperature happened */
+	EVENT_CRT_DETECT,	/*  CRT is connected */
+	EVENT_CAMERA,		/*  Camera on/off */
+	EVENT_USB_OC2,		/*  USB2 Over Current occurred */
+	EVENT_USB_OC0,		/*  USB0 Over Current occurred */
+	EVENT_BLACK_SCREEN,	/*  Turn on/off backlight */
+	EVENT_AUDIO_MUTE,	/*  Mute on/off */
+	EVENT_DISPLAY_BRIGHTNESS,/* LCD backlight brightness adjust */
+	EVENT_AC_BAT,		/*  AC & Battery relative issue */
+	EVENT_AUDIO_VOLUME,	/*  Volume adjust */
+	EVENT_WLAN,		/*  Wlan on/off */
+	EVENT_END
+};
+
+#endif /* !_EC_KB3310B_H */