mmc: mmci: Initial support to manage variant specific callbacks

To be able to better support different mmci variants, we need to be able to
use variant specific callbacks, rather than continue to sprinkle the code
with additional variant data. To move in this direction, let's add an
optional ->init() callback to the variant data struct, which variants shall
use to assign the mmci_host_ops pointer.

Using an ->init() callback enables us to partition the code between
different files. To allow separate mmci variant files to implement the
variant specifics, let's also move the definition of the struct
variant_data to the common mmci header file.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Ludovic Barre <ludovic.barre@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

drivers/mmc/host/mmci.c

@@ -48,78 +48,6 @@
 
 static unsigned int fmax = 515633;
 
-/**
- * struct variant_data - MMCI variant-specific quirks
- * @clkreg: default value for MCICLOCK register
- * @clkreg_enable: enable value for MMCICLOCK register
- * @clkreg_8bit_bus_enable: enable value for 8 bit bus
- * @clkreg_neg_edge_enable: enable value for inverted data/cmd output
- * @datalength_bits: number of bits in the MMCIDATALENGTH register
- * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
- *	      is asserted (likewise for RX)
- * @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY
- *		  is asserted (likewise for RX)
- * @data_cmd_enable: enable value for data commands.
- * @st_sdio: enable ST specific SDIO logic
- * @st_clkdiv: true if using a ST-specific clock divider algorithm
- * @datactrl_mask_ddrmode: ddr mode mask in datactrl register.
- * @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
- * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl
- *		     register
- * @datactrl_mask_sdio: SDIO enable mask in datactrl register
- * @pwrreg_powerup: power up value for MMCIPOWER register
- * @f_max: maximum clk frequency supported by the controller.
- * @signal_direction: input/out direction of bus signals can be indicated
- * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock
- * @busy_detect: true if the variant supports busy detection on DAT0.
- * @busy_dpsm_flag: bitmask enabling busy detection in the DPSM
- * @busy_detect_flag: bitmask identifying the bit in the MMCISTATUS register
- *		      indicating that the card is busy
- * @busy_detect_mask: bitmask identifying the bit in the MMCIMASK0 to mask for
- *		      getting busy end detection interrupts
- * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
- * @explicit_mclk_control: enable explicit mclk control in driver.
- * @qcom_fifo: enables qcom specific fifo pio read logic.
- * @qcom_dml: enables qcom specific dma glue for dma transfers.
- * @reversed_irq_handling: handle data irq before cmd irq.
- * @mmcimask1: true if variant have a MMCIMASK1 register.
- * @start_err: bitmask identifying the STARTBITERR bit inside MMCISTATUS
- *	       register.
- * @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register
- */
-struct variant_data {
-	unsigned int		clkreg;
-	unsigned int		clkreg_enable;
-	unsigned int		clkreg_8bit_bus_enable;
-	unsigned int		clkreg_neg_edge_enable;
-	unsigned int		datalength_bits;
-	unsigned int		fifosize;
-	unsigned int		fifohalfsize;
-	unsigned int		data_cmd_enable;
-	unsigned int		datactrl_mask_ddrmode;
-	unsigned int		datactrl_mask_sdio;
-	bool			st_sdio;
-	bool			st_clkdiv;
-	bool			blksz_datactrl16;
-	bool			blksz_datactrl4;
-	u32			pwrreg_powerup;
-	u32			f_max;
-	bool			signal_direction;
-	bool			pwrreg_clkgate;
-	bool			busy_detect;
-	u32			busy_dpsm_flag;
-	u32			busy_detect_flag;
-	u32			busy_detect_mask;
-	bool			pwrreg_nopower;
-	bool			explicit_mclk_control;
-	bool			qcom_fifo;
-	bool			qcom_dml;
-	bool			reversed_irq_handling;
-	bool			mmcimask1;
-	u32			start_err;
-	u32			opendrain;
-};
-
 static struct variant_data variant_arm = {
 	.fifosize		= 16 * 4,
 	.fifohalfsize		= 8 * 4,
@@ -1706,6 +1634,9 @@ static int mmci_probe(struct amba_device *dev,
 		goto clk_disable;
 	}
 
+	if (variant->init)
+		variant->init(host);
+
 	/*
 	 * The ARM and ST versions of the block have slightly different
 	 * clock divider equations which means that the minimum divider

drivers/mmc/host/mmci.h

@@ -195,8 +195,85 @@
 #define MMCI_PINCTRL_STATE_OPENDRAIN "opendrain"
 
 struct clk;
-struct variant_data;
 struct dma_chan;
+struct mmci_host;
+
+/**
+ * struct variant_data - MMCI variant-specific quirks
+ * @clkreg: default value for MCICLOCK register
+ * @clkreg_enable: enable value for MMCICLOCK register
+ * @clkreg_8bit_bus_enable: enable value for 8 bit bus
+ * @clkreg_neg_edge_enable: enable value for inverted data/cmd output
+ * @datalength_bits: number of bits in the MMCIDATALENGTH register
+ * @fifosize: number of bytes that can be written when MMCI_TXFIFOEMPTY
+ *	      is asserted (likewise for RX)
+ * @fifohalfsize: number of bytes that can be written when MCI_TXFIFOHALFEMPTY
+ *		  is asserted (likewise for RX)
+ * @data_cmd_enable: enable value for data commands.
+ * @st_sdio: enable ST specific SDIO logic
+ * @st_clkdiv: true if using a ST-specific clock divider algorithm
+ * @datactrl_mask_ddrmode: ddr mode mask in datactrl register.
+ * @blksz_datactrl16: true if Block size is at b16..b30 position in datactrl register
+ * @blksz_datactrl4: true if Block size is at b4..b16 position in datactrl
+ *		     register
+ * @datactrl_mask_sdio: SDIO enable mask in datactrl register
+ * @pwrreg_powerup: power up value for MMCIPOWER register
+ * @f_max: maximum clk frequency supported by the controller.
+ * @signal_direction: input/out direction of bus signals can be indicated
+ * @pwrreg_clkgate: MMCIPOWER register must be used to gate the clock
+ * @busy_detect: true if the variant supports busy detection on DAT0.
+ * @busy_dpsm_flag: bitmask enabling busy detection in the DPSM
+ * @busy_detect_flag: bitmask identifying the bit in the MMCISTATUS register
+ *		      indicating that the card is busy
+ * @busy_detect_mask: bitmask identifying the bit in the MMCIMASK0 to mask for
+ *		      getting busy end detection interrupts
+ * @pwrreg_nopower: bits in MMCIPOWER don't controls ext. power supply
+ * @explicit_mclk_control: enable explicit mclk control in driver.
+ * @qcom_fifo: enables qcom specific fifo pio read logic.
+ * @qcom_dml: enables qcom specific dma glue for dma transfers.
+ * @reversed_irq_handling: handle data irq before cmd irq.
+ * @mmcimask1: true if variant have a MMCIMASK1 register.
+ * @start_err: bitmask identifying the STARTBITERR bit inside MMCISTATUS
+ *	       register.
+ * @opendrain: bitmask identifying the OPENDRAIN bit inside MMCIPOWER register
+ */
+struct variant_data {
+	unsigned int		clkreg;
+	unsigned int		clkreg_enable;
+	unsigned int		clkreg_8bit_bus_enable;
+	unsigned int		clkreg_neg_edge_enable;
+	unsigned int		datalength_bits;
+	unsigned int		fifosize;
+	unsigned int		fifohalfsize;
+	unsigned int		data_cmd_enable;
+	unsigned int		datactrl_mask_ddrmode;
+	unsigned int		datactrl_mask_sdio;
+	bool			st_sdio;
+	bool			st_clkdiv;
+	bool			blksz_datactrl16;
+	bool			blksz_datactrl4;
+	u32			pwrreg_powerup;
+	u32			f_max;
+	bool			signal_direction;
+	bool			pwrreg_clkgate;
+	bool			busy_detect;
+	u32			busy_dpsm_flag;
+	u32			busy_detect_flag;
+	u32			busy_detect_mask;
+	bool			pwrreg_nopower;
+	bool			explicit_mclk_control;
+	bool			qcom_fifo;
+	bool			qcom_dml;
+	bool			reversed_irq_handling;
+	bool			mmcimask1;
+	u32			start_err;
+	u32			opendrain;
+	void (*init)(struct mmci_host *host);
+};
+
+/* mmci variant callbacks */
+struct mmci_host_ops {
+};
 
 struct mmci_host_next {
 	struct dma_async_tx_descriptor	*dma_desc;
@@ -228,6 +305,7 @@ struct mmci_host {
 	u32			mask1_reg;
 	bool			vqmmc_enabled;
 	struct mmci_platform_data *plat;
+	struct mmci_host_ops	*ops;
 	struct variant_data	*variant;
 	struct pinctrl		*pinctrl;
 	struct pinctrl_state	*pins_default;