Merge tag 'nand/for-4.13' into MTD

From Boris:
"""
This pull request contains the following core changes:

* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
  settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
  return ENOTSUPP use a dummy ->set/get_features implementation
  returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
  NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
  implementations
* change the prototype of ->setup_data_interface()

A bunch of driver related changes:

* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
  work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
  driver

And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""

Documentation/devicetree/bindings/mtd/denali-nand.txt

@@ -3,10 +3,23 @@
 Required properties:
   - compatible : should be one of the following:
       "altr,socfpga-denali-nand"            - for Altera SOCFPGA
+      "socionext,uniphier-denali-nand-v5a"  - for Socionext UniPhier (v5a)
+      "socionext,uniphier-denali-nand-v5b"  - for Socionext UniPhier (v5b)
   - reg : should contain registers location and length for data and reg.
   - reg-names: Should contain the reg names "nand_data" and "denali_reg"
   - interrupts : The interrupt number.
 
+Optional properties:
+  - nand-ecc-step-size: see nand.txt for details.  If present, the value must be
+      512        for "altr,socfpga-denali-nand"
+      1024       for "socionext,uniphier-denali-nand-v5a"
+      1024       for "socionext,uniphier-denali-nand-v5b"
+  - nand-ecc-strength: see nand.txt for details.  Valid values are:
+      8, 15      for "altr,socfpga-denali-nand"
+      8, 16, 24  for "socionext,uniphier-denali-nand-v5a"
+      8, 16      for "socionext,uniphier-denali-nand-v5b"
+  - nand-ecc-maximize: see nand.txt for details
+
 The device tree may optionally contain sub-nodes describing partitions of the
 address space. See partition.txt for more detail.
 

Documentation/devicetree/bindings/mtd/elm.txt

 Error location module
 
 Required properties:
-- compatible: Must be "ti,am33xx-elm"
+- compatible: Must be "ti,am3352-elm"
 - reg: physical base address and size of the registers map.
 - interrupts: Interrupt number for the elm.
 

Documentation/devicetree/bindings/mtd/gpmc-nand.txt

@@ -5,7 +5,7 @@ the GPMC controller with a name of "nand".
 
 All timing relevant properties as well as generic gpmc child properties are
 explained in a separate documents - please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 For NAND specific properties such as ECC modes or bus width, please refer to
 Documentation/devicetree/bindings/mtd/nand.txt

Documentation/devicetree/bindings/mtd/gpmc-nor.txt

@@ -5,7 +5,7 @@ child nodes of the GPMC controller with a name of "nor".
 
 All timing relevant properties as well as generic GPMC child properties are
 explained in a separate documents. Please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Required properties:
 - bank-width: 		Width of NOR flash in bytes. GPMC supports 8-bit and
@@ -28,7 +28,7 @@ Required properties:
 
 Optional properties:
 - gpmc,XXX		Additional GPMC timings and settings parameters. See
-			Documentation/devicetree/bindings/bus/ti-gpmc.txt
+			Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Optional properties for partition table parsing:
 - #address-cells: should be set to 1

Documentation/devicetree/bindings/mtd/gpmc-onenand.txt

@@ -5,7 +5,7 @@ the GPMC controller with a name of "onenand".
 
 All timing relevant properties as well as generic gpmc child properties are
 explained in a separate documents - please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Required properties:
 

Documentation/devicetree/bindings/mtd/gpmi-nand.txt

@@ -4,7 +4,12 @@ The GPMI nand controller provides an interface to control the
 NAND flash chips.
 
 Required properties:
-  - compatible : should be "fsl,<chip>-gpmi-nand"
+  - compatible : should be "fsl,<chip>-gpmi-nand", chip can be:
+    * imx23
+    * imx28
+    * imx6q
+    * imx6sx
+    * imx7d
   - reg : should contain registers location and length for gpmi and bch.
   - reg-names: Should contain the reg names "gpmi-nand" and "bch"
   - interrupts : BCH interrupt number.
@@ -13,6 +18,13 @@ Required properties:
     and GPMI DMA channel ID.
     Refer to dma.txt and fsl-mxs-dma.txt for details.
   - dma-names: Must be "rx-tx".
+  - clocks : clocks phandle and clock specifier corresponding to each clock
+    specified in clock-names.
+  - clock-names : The "gpmi_io" clock is always required. Which clocks are
+    exactly required depends on chip:
+    * imx23/imx28 : "gpmi_io"
+    * imx6q/sx : "gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch"
+    * imx7d : "gpmi_io", "gpmi_bch_apb"
 
 Optional properties:
   - nand-on-flash-bbt: boolean to enable on flash bbt option if not

Documentation/devicetree/bindings/mtd/mtk-nand.txt

@@ -12,7 +12,8 @@ tree nodes.
 
 The first part of NFC is NAND Controller Interface (NFI) HW.
 Required NFI properties:
-- compatible:			Should be "mediatek,mtxxxx-nfc".
+- compatible:			Should be one of "mediatek,mt2701-nfc",
+				"mediatek,mt2712-nfc".
 - reg:				Base physical address and size of NFI.
 - interrupts:			Interrupts of NFI.
 - clocks:			NFI required clocks.
@@ -141,7 +142,7 @@ Example:
 ==============
 
 Required BCH properties:
-- compatible:	Should be "mediatek,mtxxxx-ecc".
+- compatible:	Should be one of "mediatek,mt2701-ecc", "mediatek,mt2712-ecc".
 - reg:		Base physical address and size of ECC.
 - interrupts:	Interrupts of ECC.
 - clocks:	ECC required clocks.

Documentation/devicetree/bindings/mtd/nand.txt

@@ -21,7 +21,7 @@ Optional NAND chip properties:
 
 - nand-ecc-mode : String, operation mode of the NAND ecc mode.
 		  Supported values are: "none", "soft", "hw", "hw_syndrome",
-		  "hw_oob_first".
+		  "hw_oob_first", "on-die".
 		  Deprecated values:
 		  "soft_bch": use "soft" and nand-ecc-algo instead
 - nand-ecc-algo: string, algorithm of NAND ECC.

Documentation/devicetree/bindings/net/gpmc-eth.txt

@@ -9,7 +9,7 @@ the GPMC controller with an "ethernet" name.
 
 All timing relevant properties as well as generic GPMC child properties are
 explained in a separate documents. Please refer to
-Documentation/devicetree/bindings/bus/ti-gpmc.txt
+Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 For the properties relevant to the ethernet controller connected to the GPMC
 refer to the binding documentation of the device. For example, the documentation
@@ -43,7 +43,7 @@ Required properties:
 
 Optional properties:
 - gpmc,XXX		Additional GPMC timings and settings parameters. See
-			Documentation/devicetree/bindings/bus/ti-gpmc.txt
+			Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 
 Example:
 

MAINTAINERS

@@ -3895,6 +3895,12 @@ M:	Pali Rohár <pali.rohar@gmail.com>
 S:	Maintained
 F:	drivers/platform/x86/dell-wmi.c
 
+DENALI NAND DRIVER
+M:	Masahiro Yamada <yamada.masahiro@socionext.com>
+L:	linux-mtd@lists.infradead.org
+S:	Supported
+F:	drivers/mtd/nand/denali*
+
 DESIGNWARE USB2 DRD IP DRIVER
 M:	John Youn <johnyoun@synopsys.com>
 L:	linux-usb@vger.kernel.org

drivers/mtd/nand/Kconfig

@@ -308,6 +308,7 @@ config MTD_NAND_CS553X
 config MTD_NAND_ATMEL
 	tristate "Support for NAND Flash / SmartMedia on AT91"
 	depends on ARCH_AT91
+	select MFD_ATMEL_SMC
 	help
 	  Enables support for NAND Flash / Smart Media Card interface
 	  on Atmel AT91 processors.
@@ -542,6 +543,7 @@ config MTD_NAND_SUNXI
 
 config MTD_NAND_HISI504
 	tristate "Support for NAND controller on Hisilicon SoC Hip04"
+	depends on ARCH_HISI || COMPILE_TEST
 	depends on HAS_DMA
 	help
 	  Enables support for NAND controller on Hisilicon SoC Hip04.
@@ -555,6 +557,7 @@ config MTD_NAND_QCOM
 
 config MTD_NAND_MTK
 	tristate "Support for NAND controller on MTK SoCs"
+	depends on ARCH_MEDIATEK || COMPILE_TEST
 	depends on HAS_DMA
 	help
 	  Enables support for NAND controller on MTK SoCs.

drivers/mtd/nand/bcm47xxnflash/ops_bcm4706.c

@@ -392,6 +392,8 @@ int bcm47xxnflash_ops_bcm4706_init(struct bcm47xxnflash *b47n)
 	b47n->nand_chip.read_byte = bcm47xxnflash_ops_bcm4706_read_byte;
 	b47n->nand_chip.read_buf = bcm47xxnflash_ops_bcm4706_read_buf;
 	b47n->nand_chip.write_buf = bcm47xxnflash_ops_bcm4706_write_buf;
+	b47n->nand_chip.onfi_set_features = nand_onfi_get_set_features_notsupp;
+	b47n->nand_chip.onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	nand_chip->chip_delay = 50;
 	b47n->nand_chip.bbt_options = NAND_BBT_USE_FLASH;

drivers/mtd/nand/cafe_nand.c

@@ -654,6 +654,8 @@ static int cafe_nand_probe(struct pci_dev *pdev,
 	cafe->nand.read_buf = cafe_read_buf;
 	cafe->nand.write_buf = cafe_write_buf;
 	cafe->nand.select_chip = cafe_select_chip;
+	cafe->nand.onfi_set_features = nand_onfi_get_set_features_notsupp;
+	cafe->nand.onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	cafe->nand.chip_delay = 0;
 

drivers/mtd/nand/davinci_nand.c

@@ -771,11 +771,14 @@ static int nand_davinci_probe(struct platform_device *pdev)
 			info->chip.ecc.hwctl = nand_davinci_hwctl_4bit;
 			info->chip.ecc.bytes = 10;
 			info->chip.ecc.options = NAND_ECC_GENERIC_ERASED_CHECK;
+			info->chip.ecc.algo = NAND_ECC_BCH;
 		} else {
+			/* 1bit ecc hamming */
 			info->chip.ecc.calculate = nand_davinci_calculate_1bit;
 			info->chip.ecc.correct = nand_davinci_correct_1bit;
 			info->chip.ecc.hwctl = nand_davinci_hwctl_1bit;
 			info->chip.ecc.bytes = 3;
+			info->chip.ecc.algo = NAND_ECC_HAMMING;
 		}
 		info->chip.ecc.size = 512;
 		info->chip.ecc.strength = pdata->ecc_bits;

drivers/mtd/nand/denali_dt.c

@@ -32,10 +32,31 @@ struct denali_dt {
 struct denali_dt_data {
 	unsigned int revision;
 	unsigned int caps;
+	const struct nand_ecc_caps *ecc_caps;
 };
 
+NAND_ECC_CAPS_SINGLE(denali_socfpga_ecc_caps, denali_calc_ecc_bytes,
+		     512, 8, 15);
 static const struct denali_dt_data denali_socfpga_data = {
 	.caps = DENALI_CAP_HW_ECC_FIXUP,
+	.ecc_caps = &denali_socfpga_ecc_caps,
+};
+
+NAND_ECC_CAPS_SINGLE(denali_uniphier_v5a_ecc_caps, denali_calc_ecc_bytes,
+		     1024, 8, 16, 24);
+static const struct denali_dt_data denali_uniphier_v5a_data = {
+	.caps = DENALI_CAP_HW_ECC_FIXUP |
+		DENALI_CAP_DMA_64BIT,
+	.ecc_caps = &denali_uniphier_v5a_ecc_caps,
+};
+
+NAND_ECC_CAPS_SINGLE(denali_uniphier_v5b_ecc_caps, denali_calc_ecc_bytes,
+		     1024, 8, 16);
+static const struct denali_dt_data denali_uniphier_v5b_data = {
+	.revision = 0x0501,
+	.caps = DENALI_CAP_HW_ECC_FIXUP |
+		DENALI_CAP_DMA_64BIT,
+	.ecc_caps = &denali_uniphier_v5b_ecc_caps,
 };
 
 static const struct of_device_id denali_nand_dt_ids[] = {
@@ -43,13 +64,21 @@ static const struct of_device_id denali_nand_dt_ids[] = {
 		.compatible = "altr,socfpga-denali-nand",
 		.data = &denali_socfpga_data,
 	},
+	{
+		.compatible = "socionext,uniphier-denali-nand-v5a",
+		.data = &denali_uniphier_v5a_data,
+	},
+	{
+		.compatible = "socionext,uniphier-denali-nand-v5b",
+		.data = &denali_uniphier_v5b_data,
+	},
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, denali_nand_dt_ids);
 
 static int denali_dt_probe(struct platform_device *pdev)
 {
-	struct resource *denali_reg, *nand_data;
+	struct resource *res;
 	struct denali_dt *dt;
 	const struct denali_dt_data *data;
 	struct denali_nand_info *denali;
@@ -64,9 +93,9 @@ static int denali_dt_probe(struct platform_device *pdev)
 	if (data) {
 		denali->revision = data->revision;
 		denali->caps = data->caps;
+		denali->ecc_caps = data->ecc_caps;
 	}
 
-	denali->platform = DT;
 	denali->dev = &pdev->dev;
 	denali->irq = platform_get_irq(pdev, 0);
 	if (denali->irq < 0) {
@@ -74,17 +103,15 @@ static int denali_dt_probe(struct platform_device *pdev)
 		return denali->irq;
 	}
 
-	denali_reg = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-						  "denali_reg");
-	denali->flash_reg = devm_ioremap_resource(&pdev->dev, denali_reg);
-	if (IS_ERR(denali->flash_reg))
-		return PTR_ERR(denali->flash_reg);
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "denali_reg");
+	denali->reg = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(denali->reg))
+		return PTR_ERR(denali->reg);
 
-	nand_data = platform_get_resource_byname(pdev, IORESOURCE_MEM,
-						 "nand_data");
-	denali->flash_mem = devm_ioremap_resource(&pdev->dev, nand_data);
-	if (IS_ERR(denali->flash_mem))
-		return PTR_ERR(denali->flash_mem);
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nand_data");
+	denali->host = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(denali->host))
+		return PTR_ERR(denali->host);
 
 	dt->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(dt->clk)) {
@@ -93,6 +120,8 @@ static int denali_dt_probe(struct platform_device *pdev)
 	}
 	clk_prepare_enable(dt->clk);
 
+	denali->clk_x_rate = clk_get_rate(dt->clk);
+
 	ret = denali_init(denali);
 	if (ret)
 		goto out_disable_clk;

drivers/mtd/nand/denali_pci.c

@@ -19,6 +19,9 @@
 
 #define DENALI_NAND_NAME    "denali-nand-pci"
 
+#define INTEL_CE4100	1
+#define INTEL_MRST	2
+
 /* List of platforms this NAND controller has be integrated into */
 static const struct pci_device_id denali_pci_ids[] = {
 	{ PCI_VDEVICE(INTEL, 0x0701), INTEL_CE4100 },
@@ -27,6 +30,8 @@ static const struct pci_device_id denali_pci_ids[] = {
 };
 MODULE_DEVICE_TABLE(pci, denali_pci_ids);
 
+NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
+
 static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 {
 	int ret;
@@ -45,13 +50,11 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	}
 
 	if (id->driver_data == INTEL_CE4100) {
-		denali->platform = INTEL_CE4100;
 		mem_base = pci_resource_start(dev, 0);
 		mem_len = pci_resource_len(dev, 1);
 		csr_base = pci_resource_start(dev, 1);
 		csr_len = pci_resource_len(dev, 1);
 	} else {
-		denali->platform = INTEL_MRST;
 		csr_base = pci_resource_start(dev, 0);
 		csr_len = pci_resource_len(dev, 0);
 		mem_base = pci_resource_start(dev, 1);
@@ -65,6 +68,9 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	pci_set_master(dev);
 	denali->dev = &dev->dev;
 	denali->irq = dev->irq;
+	denali->ecc_caps = &denali_pci_ecc_caps;
+	denali->nand.ecc.options |= NAND_ECC_MAXIMIZE;
+	denali->clk_x_rate = 200000000;		/* 200 MHz */
 
 	ret = pci_request_regions(dev, DENALI_NAND_NAME);
 	if (ret) {
@@ -72,14 +78,14 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 		return ret;
 	}
 
-	denali->flash_reg = ioremap_nocache(csr_base, csr_len);
-	if (!denali->flash_reg) {
+	denali->reg = ioremap_nocache(csr_base, csr_len);
+	if (!denali->reg) {
 		dev_err(&dev->dev, "Spectra: Unable to remap memory region\n");
 		return -ENOMEM;
 	}
 
-	denali->flash_mem = ioremap_nocache(mem_base, mem_len);
-	if (!denali->flash_mem) {
+	denali->host = ioremap_nocache(mem_base, mem_len);
+	if (!denali->host) {
 		dev_err(&dev->dev, "Spectra: ioremap_nocache failed!");
 		ret = -ENOMEM;
 		goto failed_remap_reg;
@@ -94,9 +100,9 @@ static int denali_pci_probe(struct pci_dev *dev, const struct pci_device_id *id)
 	return 0;
 
 failed_remap_mem:
-	iounmap(denali->flash_mem);
+	iounmap(denali->host);
 failed_remap_reg:
-	iounmap(denali->flash_reg);
+	iounmap(denali->reg);
 	return ret;
 }
 
@@ -106,8 +112,8 @@ static void denali_pci_remove(struct pci_dev *dev)
 	struct denali_nand_info *denali = pci_get_drvdata(dev);
 
 	denali_remove(denali);
-	iounmap(denali->flash_reg);
-	iounmap(denali->flash_mem);
+	iounmap(denali->reg);
+	iounmap(denali->host);
 }
 
 static struct pci_driver denali_pci_driver = {

drivers/mtd/nand/docg4.c

@@ -1260,6 +1260,8 @@ static void __init init_mtd_structs(struct mtd_info *mtd)
 	nand->read_buf = docg4_read_buf;
 	nand->write_buf = docg4_write_buf16;
 	nand->erase = docg4_erase_block;
+	nand->onfi_set_features = nand_onfi_get_set_features_notsupp;
+	nand->onfi_get_features = nand_onfi_get_set_features_notsupp;
 	nand->ecc.read_page = docg4_read_page;
 	nand->ecc.write_page = docg4_write_page;
 	nand->ecc.read_page_raw = docg4_read_page_raw;

drivers/mtd/nand/fsl_elbc_nand.c

@@ -775,6 +775,8 @@ static int fsl_elbc_chip_init(struct fsl_elbc_mtd *priv)
 	chip->select_chip = fsl_elbc_select_chip;
 	chip->cmdfunc = fsl_elbc_cmdfunc;
 	chip->waitfunc = fsl_elbc_wait;
+	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	chip->bbt_td = &bbt_main_descr;
 	chip->bbt_md = &bbt_mirror_descr;

drivers/mtd/nand/fsl_ifc_nand.c

@@ -171,34 +171,6 @@ static void set_addr(struct mtd_info *mtd, int column, int page_addr, int oob)
 		ifc_nand_ctrl->index += mtd->writesize;
 }
 
-static int is_blank(struct mtd_info *mtd, unsigned int bufnum)
-{
-	struct nand_chip *chip = mtd_to_nand(mtd);
-	struct fsl_ifc_mtd *priv = nand_get_controller_data(chip);
-	u8 __iomem *addr = priv->vbase + bufnum * (mtd->writesize * 2);
-	u32 __iomem *mainarea = (u32 __iomem *)addr;
-	u8 __iomem *oob = addr + mtd->writesize;
-	struct mtd_oob_region oobregion = { };
-	int i, section = 0;
-
-	for (i = 0; i < mtd->writesize / 4; i++) {
-		if (__raw_readl(&mainarea[i]) != 0xffffffff)
-			return 0;
-	}
-
-	mtd_ooblayout_ecc(mtd, section++, &oobregion);
-	while (oobregion.length) {
-		for (i = 0; i < oobregion.length; i++) {
-			if (__raw_readb(&oob[oobregion.offset + i]) != 0xff)
-				return 0;
-		}
-
-		mtd_ooblayout_ecc(mtd, section++, &oobregion);
-	}
-
-	return 1;
-}
-
 /* returns nonzero if entire page is blank */
 static int check_read_ecc(struct mtd_info *mtd, struct fsl_ifc_ctrl *ctrl,
 			  u32 *eccstat, unsigned int bufnum)
@@ -274,16 +246,14 @@ static void fsl_ifc_run_command(struct mtd_info *mtd)
 			if (errors == 15) {
 				/*
 				 * Uncorrectable error.
-				 * OK only if the whole page is blank.
+				 * We'll check for blank pages later.
 				 *
 				 * We disable ECCER reporting due to...
 				 * erratum IFC-A002770 -- so report it now if we
 				 * see an uncorrectable error in ECCSTAT.
 				 */
-				if (!is_blank(mtd, bufnum))
-					ctrl->nand_stat |=
-						IFC_NAND_EVTER_STAT_ECCER;
-				break;
+				ctrl->nand_stat |= IFC_NAND_EVTER_STAT_ECCER;
+				continue;
 			}
 
 			mtd->ecc_stats.corrected += errors;
@@ -678,6 +648,39 @@ static int fsl_ifc_wait(struct mtd_info *mtd, struct nand_chip *chip)
 	return nand_fsr | NAND_STATUS_WP;
 }
 
+/*
+ * The controller does not check for bitflips in erased pages,
+ * therefore software must check instead.
+ */
+static int check_erased_page(struct nand_chip *chip, u8 *buf)
+{
+	struct mtd_info *mtd = nand_to_mtd(chip);
+	u8 *ecc = chip->oob_poi;
+	const int ecc_size = chip->ecc.bytes;
+	const int pkt_size = chip->ecc.size;
+	int i, res, bitflips = 0;
+	struct mtd_oob_region oobregion = { };
+
+	mtd_ooblayout_ecc(mtd, 0, &oobregion);
+	ecc += oobregion.offset;
+
+	for (i = 0; i < chip->ecc.steps; ++i) {
+		res = nand_check_erased_ecc_chunk(buf, pkt_size, ecc, ecc_size,
+						  NULL, 0,
+						  chip->ecc.strength);
+		if (res < 0)
+			mtd->ecc_stats.failed++;
+		else
+			mtd->ecc_stats.corrected += res;
+
+		bitflips = max(res, bitflips);
+		buf += pkt_size;
+		ecc += ecc_size;
+	}
+
+	return bitflips;
+}
+
 static int fsl_ifc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 			     uint8_t *buf, int oob_required, int page)
 {
@@ -689,8 +692,12 @@ static int fsl_ifc_read_page(struct mtd_info *mtd, struct nand_chip *chip,
 	if (oob_required)
 		fsl_ifc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
 
-	if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_ECCER)
-		dev_err(priv->dev, "NAND Flash ECC Uncorrectable Error\n");
+	if (ctrl->nand_stat & IFC_NAND_EVTER_STAT_ECCER) {
+		if (!oob_required)
+			fsl_ifc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
+
+		return check_erased_page(chip, buf);
+	}
 
 	if (ctrl->nand_stat != IFC_NAND_EVTER_STAT_OPC)
 		mtd->ecc_stats.failed++;
@@ -831,6 +838,8 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv)
 	chip->select_chip = fsl_ifc_select_chip;
 	chip->cmdfunc = fsl_ifc_cmdfunc;
 	chip->waitfunc = fsl_ifc_wait;
+	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	chip->bbt_td = &bbt_main_descr;
 	chip->bbt_md = &bbt_mirror_descr;
@@ -904,7 +913,7 @@ static int fsl_ifc_chip_init(struct fsl_ifc_mtd *priv)
 		chip->ecc.algo = NAND_ECC_HAMMING;
 	}
 
-	if (ctrl->version == FSL_IFC_VERSION_1_1_0)
+	if (ctrl->version >= FSL_IFC_VERSION_1_1_0)
 		fsl_ifc_sram_init(priv);
 
 	return 0;

drivers/mtd/nand/fsmc_nand.c

@@ -302,25 +302,13 @@ static void fsmc_cmd_ctrl(struct mtd_info *mtd, int cmd, unsigned int ctrl)
  * This routine initializes timing parameters related to NAND memory access in
  * FSMC registers
  */
-static void fsmc_nand_setup(void __iomem *regs, uint32_t bank,
-			   uint32_t busw, struct fsmc_nand_timings *timings)
+static void fsmc_nand_setup(struct fsmc_nand_data *host,
+			    struct fsmc_nand_timings *tims)
 {
 	uint32_t value = FSMC_DEVTYPE_NAND | FSMC_ENABLE | FSMC_WAITON;
 	uint32_t tclr, tar, thiz, thold, twait, tset;
-	struct fsmc_nand_timings *tims;
-	struct fsmc_nand_timings default_timings = {
-		.tclr	= FSMC_TCLR_1,
-		.tar	= FSMC_TAR_1,
-		.thiz	= FSMC_THIZ_1,
-		.thold	= FSMC_THOLD_4,
-		.twait	= FSMC_TWAIT_6,
-		.tset	= FSMC_TSET_0,
-	};
-
-	if (timings)
-		tims = timings;
-	else
-		tims = &default_timings;
+	unsigned int bank = host->bank;
+	void __iomem *regs = host->regs_va;
 
 	tclr = (tims->tclr & FSMC_TCLR_MASK) << FSMC_TCLR_SHIFT;
 	tar = (tims->tar & FSMC_TAR_MASK) << FSMC_TAR_SHIFT;
@@ -329,7 +317,7 @@ static void fsmc_nand_setup(void __iomem *regs, uint32_t bank,
 	twait = (tims->twait & FSMC_TWAIT_MASK) << FSMC_TWAIT_SHIFT;
 	tset = (tims->tset & FSMC_TSET_MASK) << FSMC_TSET_SHIFT;
 
-	if (busw)
+	if (host->nand.options & NAND_BUSWIDTH_16)
 		writel_relaxed(value | FSMC_DEVWID_16,
 				FSMC_NAND_REG(regs, bank, PC));
 	else
@@ -344,6 +332,87 @@ static void fsmc_nand_setup(void __iomem *regs, uint32_t bank,
 			FSMC_NAND_REG(regs, bank, ATTRIB));
 }
 
+static int fsmc_calc_timings(struct fsmc_nand_data *host,
+			     const struct nand_sdr_timings *sdrt,
+			     struct fsmc_nand_timings *tims)
+{
+	unsigned long hclk = clk_get_rate(host->clk);
+	unsigned long hclkn = NSEC_PER_SEC / hclk;
+	uint32_t thiz, thold, twait, tset;
+
+	if (sdrt->tRC_min < 30000)
+		return -EOPNOTSUPP;
+
+	tims->tar = DIV_ROUND_UP(sdrt->tAR_min / 1000, hclkn) - 1;
+	if (tims->tar > FSMC_TAR_MASK)
+		tims->tar = FSMC_TAR_MASK;
+	tims->tclr = DIV_ROUND_UP(sdrt->tCLR_min / 1000, hclkn) - 1;
+	if (tims->tclr > FSMC_TCLR_MASK)
+		tims->tclr = FSMC_TCLR_MASK;
+
+	thiz = sdrt->tCS_min - sdrt->tWP_min;
+	tims->thiz = DIV_ROUND_UP(thiz / 1000, hclkn);
+
+	thold = sdrt->tDH_min;
+	if (thold < sdrt->tCH_min)
+		thold = sdrt->tCH_min;
+	if (thold < sdrt->tCLH_min)
+		thold = sdrt->tCLH_min;
+	if (thold < sdrt->tWH_min)
+		thold = sdrt->tWH_min;
+	if (thold < sdrt->tALH_min)
+		thold = sdrt->tALH_min;
+	if (thold < sdrt->tREH_min)
+		thold = sdrt->tREH_min;
+	tims->thold = DIV_ROUND_UP(thold / 1000, hclkn);
+	if (tims->thold == 0)
+		tims->thold = 1;
+	else if (tims->thold > FSMC_THOLD_MASK)
+		tims->thold = FSMC_THOLD_MASK;
+
+	twait = max(sdrt->tRP_min, sdrt->tWP_min);
+	tims->twait = DIV_ROUND_UP(twait / 1000, hclkn) - 1;
+	if (tims->twait == 0)
+		tims->twait = 1;
+	else if (tims->twait > FSMC_TWAIT_MASK)
+		tims->twait = FSMC_TWAIT_MASK;
+
+	tset = max(sdrt->tCS_min - sdrt->tWP_min,
+		   sdrt->tCEA_max - sdrt->tREA_max);
+	tims->tset = DIV_ROUND_UP(tset / 1000, hclkn) - 1;
+	if (tims->tset == 0)
+		tims->tset = 1;
+	else if (tims->tset > FSMC_TSET_MASK)
+		tims->tset = FSMC_TSET_MASK;
+
+	return 0;
+}
+
+static int fsmc_setup_data_interface(struct mtd_info *mtd, int csline,
+				     const struct nand_data_interface *conf)
+{
+	struct nand_chip *nand = mtd_to_nand(mtd);
+	struct fsmc_nand_data *host = nand_get_controller_data(nand);
+	struct fsmc_nand_timings tims;
+	const struct nand_sdr_timings *sdrt;
+	int ret;
+
+	sdrt = nand_get_sdr_timings(conf);
+	if (IS_ERR(sdrt))
+		return PTR_ERR(sdrt);
+
+	ret = fsmc_calc_timings(host, sdrt, &tims);
+	if (ret)
+		return ret;
+
+	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
+		return 0;
+
+	fsmc_nand_setup(host, &tims);
+
+	return 0;
+}
+
 /*
  * fsmc_enable_hwecc - Enables Hardware ECC through FSMC registers
  */
@@ -796,10 +865,8 @@ static int fsmc_nand_probe_config_dt(struct platform_device *pdev,
 		return -ENOMEM;
 	ret = of_property_read_u8_array(np, "timings", (u8 *)host->dev_timings,
 						sizeof(*host->dev_timings));
-	if (ret) {
-		dev_info(&pdev->dev, "No timings in dts specified, using default timings!\n");
+	if (ret)
 		host->dev_timings = NULL;
-	}
 
 	/* Set default NAND bank to 0 */
 	host->bank = 0;
@@ -933,9 +1000,10 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 		break;
 	}
 
-	fsmc_nand_setup(host->regs_va, host->bank,
-			nand->options & NAND_BUSWIDTH_16,
-			host->dev_timings);
+	if (host->dev_timings)
+		fsmc_nand_setup(host, host->dev_timings);
+	else
+		nand->setup_data_interface = fsmc_setup_data_interface;
 
 	if (AMBA_REV_BITS(host->pid) >= 8) {
 		nand->ecc.read_page = fsmc_read_page_hwecc;
@@ -986,6 +1054,9 @@ static int __init fsmc_nand_probe(struct platform_device *pdev)
 				break;
 			}
 
+		case NAND_ECC_ON_DIE:
+			break;
+
 		default:
 			dev_err(&pdev->dev, "Unsupported ECC mode!\n");
 			goto err_probe;
@@ -1073,9 +1144,8 @@ static int fsmc_nand_resume(struct device *dev)
 	struct fsmc_nand_data *host = dev_get_drvdata(dev);
 	if (host) {
 		clk_prepare_enable(host->clk);
-		fsmc_nand_setup(host->regs_va, host->bank,
-				host->nand.options & NAND_BUSWIDTH_16,
-				host->dev_timings);
+		if (host->dev_timings)
+			fsmc_nand_setup(host, host->dev_timings);
 	}
 	return 0;
 }

drivers/mtd/nand/gpmi-nand/gpmi-lib.c

@@ -26,7 +26,7 @@
 #include "gpmi-regs.h"
 #include "bch-regs.h"
 
-static struct timing_threshod timing_default_threshold = {
+static struct timing_threshold timing_default_threshold = {
 	.max_data_setup_cycles       = (BM_GPMI_TIMING0_DATA_SETUP >>
 						BP_GPMI_TIMING0_DATA_SETUP),
 	.internal_data_setup_in_ns   = 0,
@@ -329,7 +329,7 @@ static unsigned int ns_to_cycles(unsigned int time,
 static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this,
 					struct gpmi_nfc_hardware_timing *hw)
 {
-	struct timing_threshod *nfc = &timing_default_threshold;
+	struct timing_threshold *nfc = &timing_default_threshold;
 	struct resources *r = &this->resources;
 	struct nand_chip *nand = &this->nand;
 	struct nand_timing target = this->timing;
@@ -932,7 +932,7 @@ static int enable_edo_mode(struct gpmi_nand_data *this, int mode)
 
 	nand->select_chip(mtd, 0);
 
-	/* [1] send SET FEATURE commond to NAND */
+	/* [1] send SET FEATURE command to NAND */
 	feature[0] = mode;
 	ret = nand->onfi_set_features(mtd, nand,
 				ONFI_FEATURE_ADDR_TIMING_MODE, feature);

drivers/mtd/nand/gpmi-nand/gpmi-nand.c

@@ -82,6 +82,10 @@ static int gpmi_ooblayout_free(struct mtd_info *mtd, int section,
 	return 0;
 }
 
+static const char * const gpmi_clks_for_mx2x[] = {
+	"gpmi_io",
+};
+
 static const struct mtd_ooblayout_ops gpmi_ooblayout_ops = {
 	.ecc = gpmi_ooblayout_ecc,
 	.free = gpmi_ooblayout_free,
@@ -91,24 +95,48 @@ static const struct gpmi_devdata gpmi_devdata_imx23 = {
 	.type = IS_MX23,
 	.bch_max_ecc_strength = 20,
 	.max_chain_delay = 16,
+	.clks = gpmi_clks_for_mx2x,
+	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
 };
 
 static const struct gpmi_devdata gpmi_devdata_imx28 = {
 	.type = IS_MX28,
 	.bch_max_ecc_strength = 20,
 	.max_chain_delay = 16,
+	.clks = gpmi_clks_for_mx2x,
+	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx2x),
+};
+
+static const char * const gpmi_clks_for_mx6[] = {
+	"gpmi_io", "gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch",
 };
 
 static const struct gpmi_devdata gpmi_devdata_imx6q = {
 	.type = IS_MX6Q,
 	.bch_max_ecc_strength = 40,
 	.max_chain_delay = 12,
+	.clks = gpmi_clks_for_mx6,
+	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
 };
 
 static const struct gpmi_devdata gpmi_devdata_imx6sx = {
 	.type = IS_MX6SX,
 	.bch_max_ecc_strength = 62,
 	.max_chain_delay = 12,
+	.clks = gpmi_clks_for_mx6,
+	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx6),
+};
+
+static const char * const gpmi_clks_for_mx7d[] = {
+	"gpmi_io", "gpmi_bch_apb",
+};
+
+static const struct gpmi_devdata gpmi_devdata_imx7d = {
+	.type = IS_MX7D,
+	.bch_max_ecc_strength = 62,
+	.max_chain_delay = 12,
+	.clks = gpmi_clks_for_mx7d,
+	.clks_count = ARRAY_SIZE(gpmi_clks_for_mx7d),
 };
 
 static irqreturn_t bch_irq(int irq, void *cookie)
@@ -599,35 +627,14 @@ static int acquire_dma_channels(struct gpmi_nand_data *this)
 	return -EINVAL;
 }
 
-static char *extra_clks_for_mx6q[GPMI_CLK_MAX] = {
-	"gpmi_apb", "gpmi_bch", "gpmi_bch_apb", "per1_bch",
-};
-
 static int gpmi_get_clks(struct gpmi_nand_data *this)
 {
 	struct resources *r = &this->resources;
-	char **extra_clks = NULL;
 	struct clk *clk;
 	int err, i;
 
-	/* The main clock is stored in the first. */
-	r->clock[0] = devm_clk_get(this->dev, "gpmi_io");
-	if (IS_ERR(r->clock[0])) {
-		err = PTR_ERR(r->clock[0]);
-		goto err_clock;
-	}
-
-	/* Get extra clocks */
-	if (GPMI_IS_MX6(this))
-		extra_clks = extra_clks_for_mx6q;
-	if (!extra_clks)
-		return 0;
-
-	for (i = 1; i < GPMI_CLK_MAX; i++) {
-		if (extra_clks[i - 1] == NULL)
-			break;
-
-		clk = devm_clk_get(this->dev, extra_clks[i - 1]);
+	for (i = 0; i < this->devdata->clks_count; i++) {
+		clk = devm_clk_get(this->dev, this->devdata->clks[i]);
 		if (IS_ERR(clk)) {
 			err = PTR_ERR(clk);
 			goto err_clock;
@@ -1929,12 +1936,6 @@ static int gpmi_set_geometry(struct gpmi_nand_data *this)
 	return gpmi_alloc_dma_buffer(this);
 }
 
-static void gpmi_nand_exit(struct gpmi_nand_data *this)
-{
-	nand_release(nand_to_mtd(&this->nand));
-	gpmi_free_dma_buffer(this);
-}
-
 static int gpmi_init_last(struct gpmi_nand_data *this)
 {
 	struct nand_chip *chip = &this->nand;
@@ -2048,18 +2049,20 @@ static int gpmi_nand_init(struct gpmi_nand_data *this)
 
 	ret = nand_boot_init(this);
 	if (ret)
-		goto err_out;
+		goto err_nand_cleanup;
 	ret = chip->scan_bbt(mtd);
 	if (ret)
-		goto err_out;
+		goto err_nand_cleanup;
 
 	ret = mtd_device_register(mtd, NULL, 0);
 	if (ret)
-		goto err_out;
+		goto err_nand_cleanup;
 	return 0;
 
+err_nand_cleanup:
+	nand_cleanup(chip);
 err_out:
-	gpmi_nand_exit(this);
+	gpmi_free_dma_buffer(this);
 	return ret;
 }
 
@@ -2076,6 +2079,9 @@ static const struct of_device_id gpmi_nand_id_table[] = {
 	}, {
 		.compatible = "fsl,imx6sx-gpmi-nand",
 		.data = &gpmi_devdata_imx6sx,
+	}, {
+		.compatible = "fsl,imx7d-gpmi-nand",
+		.data = &gpmi_devdata_imx7d,
 	}, {}
 };
 MODULE_DEVICE_TABLE(of, gpmi_nand_id_table);
@@ -2129,7 +2135,8 @@ static int gpmi_nand_remove(struct platform_device *pdev)
 {
 	struct gpmi_nand_data *this = platform_get_drvdata(pdev);
 
-	gpmi_nand_exit(this);
+	nand_release(nand_to_mtd(&this->nand));
+	gpmi_free_dma_buffer(this);
 	release_resources(this);
 	return 0;
 }

drivers/mtd/nand/gpmi-nand/gpmi-nand.h

@@ -123,13 +123,16 @@ enum gpmi_type {
 	IS_MX23,
 	IS_MX28,
 	IS_MX6Q,
-	IS_MX6SX
+	IS_MX6SX,
+	IS_MX7D,
 };
 
 struct gpmi_devdata {
 	enum gpmi_type type;
 	int bch_max_ecc_strength;
 	int max_chain_delay; /* See the async EDO mode */
+	const char * const *clks;
+	const int clks_count;
 };
 
 struct gpmi_nand_data {
@@ -231,7 +234,7 @@ struct gpmi_nfc_hardware_timing {
 };
 
 /**
- * struct timing_threshod - Timing threshold
+ * struct timing_threshold - Timing threshold
  * @max_data_setup_cycles:       The maximum number of data setup cycles that
  *                               can be expressed in the hardware.
  * @internal_data_setup_in_ns:   The time, in ns, that the NFC hardware requires
@@ -253,7 +256,7 @@ struct gpmi_nfc_hardware_timing {
  *                               progress, this is the clock frequency during
  *                               the most recent I/O transaction.
  */
-struct timing_threshod {
+struct timing_threshold {
 	const unsigned int      max_chip_count;
 	const unsigned int      max_data_setup_cycles;
 	const unsigned int      internal_data_setup_in_ns;
@@ -305,6 +308,8 @@ void gpmi_copy_bits(u8 *dst, size_t dst_bit_off,
 #define GPMI_IS_MX28(x)		((x)->devdata->type == IS_MX28)
 #define GPMI_IS_MX6Q(x)		((x)->devdata->type == IS_MX6Q)
 #define GPMI_IS_MX6SX(x)	((x)->devdata->type == IS_MX6SX)
+#define GPMI_IS_MX7D(x)		((x)->devdata->type == IS_MX7D)
 
-#define GPMI_IS_MX6(x)		(GPMI_IS_MX6Q(x) || GPMI_IS_MX6SX(x))
+#define GPMI_IS_MX6(x)		(GPMI_IS_MX6Q(x) || GPMI_IS_MX6SX(x) || \
+				 GPMI_IS_MX7D(x))
 #endif

drivers/mtd/nand/hisi504_nand.c

@@ -764,6 +764,8 @@ static int hisi_nfc_probe(struct platform_device *pdev)
 	chip->write_buf		= hisi_nfc_write_buf;
 	chip->read_buf		= hisi_nfc_read_buf;
 	chip->chip_delay	= HINFC504_CHIP_DELAY;
+	chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
 
 	hisi_nfc_host_init(host);
 

drivers/mtd/nand/jz4780_nand.c

@@ -205,7 +205,7 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
 		return -EINVAL;
 	}
 
-	mtd->ooblayout = &nand_ooblayout_lp_ops;
+	mtd_set_ooblayout(mtd, &nand_ooblayout_lp_ops);
 
 	return 0;
 }

drivers/mtd/nand/mpc5121_nfc.c

@@ -708,6 +708,8 @@ static int mpc5121_nfc_probe(struct platform_device *op)
 	chip->read_buf = mpc5121_nfc_read_buf;
 	chip->write_buf = mpc5121_nfc_write_buf;
 	chip->select_chip = mpc5121_nfc_select_chip;
+	chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
 	chip->bbt_options = NAND_BBT_USE_FLASH;
 	chip->ecc.mode = NAND_ECC_SOFT;
 	chip->ecc.algo = NAND_ECC_HAMMING;

drivers/mtd/nand/mtk_ecc.c

@@ -28,36 +28,16 @@
 
 #define ECC_IDLE_MASK		BIT(0)
 #define ECC_IRQ_EN		BIT(0)
+#define ECC_PG_IRQ_SEL		BIT(1)
 #define ECC_OP_ENABLE		(1)
 #define ECC_OP_DISABLE		(0)
 
 #define ECC_ENCCON		(0x00)
 #define ECC_ENCCNFG		(0x04)
-#define		ECC_CNFG_4BIT		(0)
-#define		ECC_CNFG_6BIT		(1)
-#define		ECC_CNFG_8BIT		(2)
-#define		ECC_CNFG_10BIT		(3)
-#define		ECC_CNFG_12BIT		(4)
-#define		ECC_CNFG_14BIT		(5)
-#define		ECC_CNFG_16BIT		(6)
-#define		ECC_CNFG_18BIT		(7)
-#define		ECC_CNFG_20BIT		(8)
-#define		ECC_CNFG_22BIT		(9)
-#define		ECC_CNFG_24BIT		(0xa)
-#define		ECC_CNFG_28BIT		(0xb)
-#define		ECC_CNFG_32BIT		(0xc)
-#define		ECC_CNFG_36BIT		(0xd)
-#define		ECC_CNFG_40BIT		(0xe)
-#define		ECC_CNFG_44BIT		(0xf)
-#define		ECC_CNFG_48BIT		(0x10)
-#define		ECC_CNFG_52BIT		(0x11)
-#define		ECC_CNFG_56BIT		(0x12)
-#define		ECC_CNFG_60BIT		(0x13)
 #define		ECC_MODE_SHIFT		(5)
 #define		ECC_MS_SHIFT		(16)
 #define ECC_ENCDIADDR		(0x08)
 #define ECC_ENCIDLE		(0x0C)
-#define ECC_ENCPAR(x)		(0x10 + (x) * sizeof(u32))
 #define ECC_ENCIRQ_EN		(0x80)
 #define ECC_ENCIRQ_STA		(0x84)
 #define ECC_DECCON		(0x100)
@@ -66,7 +46,6 @@
 #define		DEC_CNFG_CORRECT	(0x3 << 12)
 #define ECC_DECIDLE		(0x10C)
 #define ECC_DECENUM0		(0x114)
-#define		ERR_MASK		(0x3f)
 #define ECC_DECDONE		(0x124)
 #define ECC_DECIRQ_EN		(0x200)
 #define ECC_DECIRQ_STA		(0x204)
@@ -78,8 +57,17 @@
 #define ECC_IRQ_REG(op)		((op) == ECC_ENCODE ? \
 					ECC_ENCIRQ_EN : ECC_DECIRQ_EN)
 
+struct mtk_ecc_caps {
+	u32 err_mask;
+	const u8 *ecc_strength;
+	u8 num_ecc_strength;
+	u32 encode_parity_reg0;
+	int pg_irq_sel;
+};
+
 struct mtk_ecc {
 	struct device *dev;
+	const struct mtk_ecc_caps *caps;
 	void __iomem *regs;
 	struct clk *clk;
 
@@ -87,7 +75,18 @@ struct mtk_ecc {
 	struct mutex lock;
 	u32 sectors;
 
-	u8 eccdata[112];
+	u8 *eccdata;
+};
+
+/* ecc strength that each IP supports */
+static const u8 ecc_strength_mt2701[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+	40, 44, 48, 52, 56, 60
+};
+
+static const u8 ecc_strength_mt2712[] = {
+	4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
+	40, 44, 48, 52, 56, 60, 68, 72, 80
 };
 
 static inline void mtk_ecc_wait_idle(struct mtk_ecc *ecc,
@@ -136,77 +135,24 @@ static irqreturn_t mtk_ecc_irq(int irq, void *id)
 	return IRQ_HANDLED;
 }
 
-static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
+static int mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 {
-	u32 ecc_bit = ECC_CNFG_4BIT, dec_sz, enc_sz;
-	u32 reg;
-
-	switch (config->strength) {
-	case 4:
-		ecc_bit = ECC_CNFG_4BIT;
-		break;
-	case 6:
-		ecc_bit = ECC_CNFG_6BIT;
-		break;
-	case 8:
-		ecc_bit = ECC_CNFG_8BIT;
-		break;
-	case 10:
-		ecc_bit = ECC_CNFG_10BIT;
-		break;
-	case 12:
-		ecc_bit = ECC_CNFG_12BIT;
-		break;
-	case 14:
-		ecc_bit = ECC_CNFG_14BIT;
-		break;
-	case 16:
-		ecc_bit = ECC_CNFG_16BIT;
-		break;
-	case 18:
-		ecc_bit = ECC_CNFG_18BIT;
-		break;
-	case 20:
-		ecc_bit = ECC_CNFG_20BIT;
-		break;
-	case 22:
-		ecc_bit = ECC_CNFG_22BIT;
-		break;
-	case 24:
-		ecc_bit = ECC_CNFG_24BIT;
-		break;
-	case 28:
-		ecc_bit = ECC_CNFG_28BIT;
-		break;
-	case 32:
-		ecc_bit = ECC_CNFG_32BIT;
-		break;
-	case 36:
-		ecc_bit = ECC_CNFG_36BIT;
-		break;
-	case 40:
-		ecc_bit = ECC_CNFG_40BIT;
-		break;
-	case 44:
-		ecc_bit = ECC_CNFG_44BIT;
-		break;
-	case 48:
-		ecc_bit = ECC_CNFG_48BIT;
-		break;
-	case 52:
-		ecc_bit = ECC_CNFG_52BIT;
-		break;
-	case 56:
-		ecc_bit = ECC_CNFG_56BIT;
-		break;
-	case 60:
-		ecc_bit = ECC_CNFG_60BIT;
-		break;
-	default:
-		dev_err(ecc->dev, "invalid strength %d, default to 4 bits\n",
+	u32 ecc_bit, dec_sz, enc_sz;
+	u32 reg, i;
+
+	for (i = 0; i < ecc->caps->num_ecc_strength; i++) {
+		if (ecc->caps->ecc_strength[i] == config->strength)
+			break;
+	}
+
+	if (i == ecc->caps->num_ecc_strength) {
+		dev_err(ecc->dev, "invalid ecc strength %d\n",
 			config->strength);
+		return -EINVAL;
 	}
 
+	ecc_bit = i;
+
 	if (config->op == ECC_ENCODE) {
 		/* configure ECC encoder (in bits) */
 		enc_sz = config->len << 3;
@@ -232,6 +178,8 @@ static void mtk_ecc_config(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 		if (config->sectors)
 			ecc->sectors = 1 << (config->sectors - 1);
 	}
+
+	return 0;
 }
 
 void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats,
@@ -247,8 +195,8 @@ void mtk_ecc_get_stats(struct mtk_ecc *ecc, struct mtk_ecc_stats *stats,
 		offset = (i >> 2) << 2;
 		err = readl(ecc->regs + ECC_DECENUM0 + offset);
 		err = err >> ((i % 4) * 8);
-		err &= ERR_MASK;
-		if (err == ERR_MASK) {
+		err &= ecc->caps->err_mask;
+		if (err == ecc->caps->err_mask) {
 			/* uncorrectable errors */
 			stats->failed++;
 			continue;
@@ -313,6 +261,7 @@ EXPORT_SYMBOL(of_mtk_ecc_get);
 int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 {
 	enum mtk_ecc_operation op = config->op;
+	u16 reg_val;
 	int ret;
 
 	ret = mutex_lock_interruptible(&ecc->lock);
@@ -322,11 +271,27 @@ int mtk_ecc_enable(struct mtk_ecc *ecc, struct mtk_ecc_config *config)
 	}
 
 	mtk_ecc_wait_idle(ecc, op);
-	mtk_ecc_config(ecc, config);
-	writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
 
-	init_completion(&ecc->done);
-	writew(ECC_IRQ_EN, ecc->regs + ECC_IRQ_REG(op));
+	ret = mtk_ecc_config(ecc, config);
+	if (ret) {
+		mutex_unlock(&ecc->lock);
+		return ret;
+	}
+
+	if (config->mode != ECC_NFI_MODE || op != ECC_ENCODE) {
+		init_completion(&ecc->done);
+		reg_val = ECC_IRQ_EN;
+		/*
+		 * For ECC_NFI_MODE, if ecc->caps->pg_irq_sel is 1, then it
+		 * means this chip can only generate one ecc irq during page
+		 * read / write. If is 0, generate one ecc irq each ecc step.
+		 */
+		if (ecc->caps->pg_irq_sel && config->mode == ECC_NFI_MODE)
+			reg_val |= ECC_PG_IRQ_SEL;
+		writew(reg_val, ecc->regs + ECC_IRQ_REG(op));
+	}
+
+	writew(ECC_OP_ENABLE, ecc->regs + ECC_CTL_REG(op));
 
 	return 0;
 }
@@ -396,7 +361,9 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
 	len = (config->strength * ECC_PARITY_BITS + 7) >> 3;
 
 	/* write the parity bytes generated by the ECC back to temp buffer */
-	__ioread32_copy(ecc->eccdata, ecc->regs + ECC_ENCPAR(0), round_up(len, 4));
+	__ioread32_copy(ecc->eccdata,
+			ecc->regs + ecc->caps->encode_parity_reg0,
+			round_up(len, 4));
 
 	/* copy into possibly unaligned OOB region with actual length */
 	memcpy(data + bytes, ecc->eccdata, len);
@@ -409,37 +376,79 @@ int mtk_ecc_encode(struct mtk_ecc *ecc, struct mtk_ecc_config *config,
 }
 EXPORT_SYMBOL(mtk_ecc_encode);
 
-void mtk_ecc_adjust_strength(u32 *p)
+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p)
 {
-	u32 ecc[] = {4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 28, 32, 36,
-			40, 44, 48, 52, 56, 60};
+	const u8 *ecc_strength = ecc->caps->ecc_strength;
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(ecc); i++) {
-		if (*p <= ecc[i]) {
+	for (i = 0; i < ecc->caps->num_ecc_strength; i++) {
+		if (*p <= ecc_strength[i]) {
 			if (!i)
-				*p = ecc[i];
-			else if (*p != ecc[i])
-				*p = ecc[i - 1];
+				*p = ecc_strength[i];
+			else if (*p != ecc_strength[i])
+				*p = ecc_strength[i - 1];
 			return;
 		}
 	}
 
-	*p = ecc[ARRAY_SIZE(ecc) - 1];
+	*p = ecc_strength[ecc->caps->num_ecc_strength - 1];
 }
 EXPORT_SYMBOL(mtk_ecc_adjust_strength);
 
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2701 = {
+	.err_mask = 0x3f,
+	.ecc_strength = ecc_strength_mt2701,
+	.num_ecc_strength = 20,
+	.encode_parity_reg0 = 0x10,
+	.pg_irq_sel = 0,
+};
+
+static const struct mtk_ecc_caps mtk_ecc_caps_mt2712 = {
+	.err_mask = 0x7f,
+	.ecc_strength = ecc_strength_mt2712,
+	.num_ecc_strength = 23,
+	.encode_parity_reg0 = 0x300,
+	.pg_irq_sel = 1,
+};
+
+static const struct of_device_id mtk_ecc_dt_match[] = {
+	{
+		.compatible = "mediatek,mt2701-ecc",
+		.data = &mtk_ecc_caps_mt2701,
+	}, {
+		.compatible = "mediatek,mt2712-ecc",
+		.data = &mtk_ecc_caps_mt2712,
+	},
+	{},
+};
+
 static int mtk_ecc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
 	struct mtk_ecc *ecc;
 	struct resource *res;
+	const struct of_device_id *of_ecc_id = NULL;
+	u32 max_eccdata_size;
 	int irq, ret;
 
 	ecc = devm_kzalloc(dev, sizeof(*ecc), GFP_KERNEL);
 	if (!ecc)
 		return -ENOMEM;
 
+	of_ecc_id = of_match_device(mtk_ecc_dt_match, &pdev->dev);
+	if (!of_ecc_id)
+		return -ENODEV;
+
+	ecc->caps = of_ecc_id->data;
+
+	max_eccdata_size = ecc->caps->num_ecc_strength - 1;
+	max_eccdata_size = ecc->caps->ecc_strength[max_eccdata_size];
+	max_eccdata_size = (max_eccdata_size * ECC_PARITY_BITS + 7) >> 3;
+	max_eccdata_size = round_up(max_eccdata_size, 4);
+	ecc->eccdata = devm_kzalloc(dev, max_eccdata_size, GFP_KERNEL);
+	if (!ecc->eccdata)
+		return -ENOMEM;
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	ecc->regs = devm_ioremap_resource(dev, res);
 	if (IS_ERR(ecc->regs)) {
@@ -500,19 +509,12 @@ static int mtk_ecc_resume(struct device *dev)
 		return ret;
 	}
 
-	mtk_ecc_hw_init(ecc);
-
 	return 0;
 }
 
 static SIMPLE_DEV_PM_OPS(mtk_ecc_pm_ops, mtk_ecc_suspend, mtk_ecc_resume);
 #endif
 
-static const struct of_device_id mtk_ecc_dt_match[] = {
-	{ .compatible = "mediatek,mt2701-ecc" },
-	{},
-};
-
 MODULE_DEVICE_TABLE(of, mtk_ecc_dt_match);
 
 static struct platform_driver mtk_ecc_driver = {

drivers/mtd/nand/mtk_ecc.h

@@ -42,7 +42,7 @@ void mtk_ecc_get_stats(struct mtk_ecc *, struct mtk_ecc_stats *, int);
 int mtk_ecc_wait_done(struct mtk_ecc *, enum mtk_ecc_operation);
 int mtk_ecc_enable(struct mtk_ecc *, struct mtk_ecc_config *);
 void mtk_ecc_disable(struct mtk_ecc *);
-void mtk_ecc_adjust_strength(u32 *);
+void mtk_ecc_adjust_strength(struct mtk_ecc *ecc, u32 *p);
 
 struct mtk_ecc *of_mtk_ecc_get(struct device_node *);
 void mtk_ecc_release(struct mtk_ecc *);

drivers/mtd/nand/mxc_nand.c

@@ -152,9 +152,8 @@ struct mxc_nand_devtype_data {
 	void (*select_chip)(struct mtd_info *mtd, int chip);
 	int (*correct_data)(struct mtd_info *mtd, u_char *dat,
 			u_char *read_ecc, u_char *calc_ecc);
-	int (*setup_data_interface)(struct mtd_info *mtd,
-				    const struct nand_data_interface *conf,
-				    bool check_only);
+	int (*setup_data_interface)(struct mtd_info *mtd, int csline,
+				    const struct nand_data_interface *conf);
 
 	/*
 	 * On i.MX21 the CONFIG2:INT bit cannot be read if interrupts are masked
@@ -1015,9 +1014,8 @@ static void preset_v1(struct mtd_info *mtd)
 	writew(0x4, NFC_V1_V2_WRPROT);
 }
 
-static int mxc_nand_v2_setup_data_interface(struct mtd_info *mtd,
-					const struct nand_data_interface *conf,
-					bool check_only)
+static int mxc_nand_v2_setup_data_interface(struct mtd_info *mtd, int csline,
+					const struct nand_data_interface *conf)
 {
 	struct nand_chip *nand_chip = mtd_to_nand(mtd);
 	struct mxc_nand_host *host = nand_get_controller_data(nand_chip);
@@ -1075,7 +1073,7 @@ static int mxc_nand_v2_setup_data_interface(struct mtd_info *mtd,
 		return -EINVAL;
 	}
 
-	if (check_only)
+	if (csline == NAND_DATA_IFACE_CHECK_ONLY)
 		return 0;
 
 	ret = clk_set_rate(host->clk, rate);

drivers/mtd/nand/orion_nand.c

@@ -166,7 +166,11 @@ static int __init orion_nand_probe(struct platform_device *pdev)
 		}
 	}
 
-	clk_prepare_enable(info->clk);
+	ret = clk_prepare_enable(info->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to prepare clock!\n");
+		return ret;
+	}
 
 	ret = nand_scan(mtd, 1);
 	if (ret)

drivers/mtd/nand/pxa3xx_nand.c

@@ -1812,6 +1812,8 @@ static int alloc_nand_resource(struct platform_device *pdev)
 		chip->write_buf		= pxa3xx_nand_write_buf;
 		chip->options		|= NAND_NO_SUBPAGE_WRITE;
 		chip->cmdfunc		= nand_cmdfunc;
+		chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
+		chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
 	}
 
 	nand_hw_control_init(chip->controller);

drivers/mtd/nand/qcom_nandc.c

@@ -2008,6 +2008,8 @@ static int qcom_nand_host_init(struct qcom_nand_controller *nandc,
 	chip->read_byte		= qcom_nandc_read_byte;
 	chip->read_buf		= qcom_nandc_read_buf;
 	chip->write_buf		= qcom_nandc_write_buf;
+	chip->onfi_set_features	= nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features	= nand_onfi_get_set_features_notsupp;
 
 	/*
 	 * the bad block marker is readable only when we read the last codeword

drivers/mtd/nand/s3c2410.c

@@ -812,9 +812,8 @@ static int s3c2410_nand_add_partition(struct s3c2410_nand_info *info,
 	return -ENODEV;
 }
 
-static int s3c2410_nand_setup_data_interface(struct mtd_info *mtd,
-					const struct nand_data_interface *conf,
-					bool check_only)
+static int s3c2410_nand_setup_data_interface(struct mtd_info *mtd, int csline,
+					const struct nand_data_interface *conf)
 {
 	struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd);
 	struct s3c2410_platform_nand *pdata = info->platform;

drivers/mtd/nand/sh_flctl.c

@@ -1183,6 +1183,8 @@ static int flctl_probe(struct platform_device *pdev)
 	nand->read_buf = flctl_read_buf;
 	nand->select_chip = flctl_select_chip;
 	nand->cmdfunc = flctl_cmdfunc;
+	nand->onfi_set_features = nand_onfi_get_set_features_notsupp;
+	nand->onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	if (pdata->flcmncr_val & SEL_16BIT)
 		nand->options |= NAND_BUSWIDTH_16;

drivers/mtd/nand/vf610_nfc.c

@@ -703,6 +703,8 @@ static int vf610_nfc_probe(struct platform_device *pdev)
 	chip->read_buf = vf610_nfc_read_buf;
 	chip->write_buf = vf610_nfc_write_buf;
 	chip->select_chip = vf610_nfc_select_chip;
+	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	chip->options |= NAND_NO_SUBPAGE_WRITE;
 

drivers/staging/mt29f_spinand/mt29f_spinand.c

@@ -915,6 +915,8 @@ static int spinand_probe(struct spi_device *spi_nand)
 	chip->waitfunc	= spinand_wait;
 	chip->options	|= NAND_CACHEPRG;
 	chip->select_chip = spinand_select_chip;
+	chip->onfi_set_features = nand_onfi_get_set_features_notsupp;
+	chip->onfi_get_features = nand_onfi_get_set_features_notsupp;
 
 	mtd = nand_to_mtd(chip);