Merge branch 'Move-MDIO-drivers-into-their-own-directory'

Andrew Lunn says:

====================
Move MDIO drivers into their own directory

The phy subdirectory is getting cluttered. It has both PHY drivers and
MDIO drivers, plus a stray switch driver. Soon more PCS drivers are
likely to appear.

Move MDIO and PCS drivers into new directories. This requires fixing
up the xgene driver which uses a relative include path.

v2:
Move the subdirs to drivers/net, rather than drivers/net/phy.

v3:
Add subdirectories under include/linux for mdio and pcs

v4:
there->their
include path fix
No new kconfig prompts
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS

@@ -1286,7 +1286,7 @@ S:	Supported
 F:	Documentation/devicetree/bindings/net/apm-xgene-enet.txt
 F:	Documentation/devicetree/bindings/net/apm-xgene-mdio.txt
 F:	drivers/net/ethernet/apm/xgene/
-F:	drivers/net/phy/mdio-xgene.c
+F:	drivers/net/mdio/mdio-xgene.c
 
 APPLIED MICRO (APM) X-GENE SOC PMU
 M:	Khuong Dinh <khuong@os.amperecomputing.com>
@@ -6513,11 +6513,14 @@ F:	Documentation/devicetree/bindings/net/ethernet-phy.yaml
 F:	Documentation/devicetree/bindings/net/mdio*
 F:	Documentation/devicetree/bindings/net/qca,ar803x.yaml
 F:	Documentation/networking/phy.rst
+F:	drivers/net/mdio/
+F:	drivers/net/pcs/
 F:	drivers/net/phy/
 F:	drivers/of/of_mdio.c
 F:	drivers/of/of_net.c
 F:	include/dt-bindings/net/qca-ar803x.h
 F:	include/linux/*mdio*.h
+F:	include/linux/mdio/*.h
 F:	include/linux/of_net.h
 F:	include/linux/phy.h
 F:	include/linux/phy_fixed.h
@@ -10497,7 +10500,7 @@ M:	Tobias Waldekranz <tobias@waldekranz.com>
 L:	netdev@vger.kernel.org
 S:	Maintained
 F:	Documentation/devicetree/bindings/net/marvell,mvusb.yaml
-F:	drivers/net/phy/mdio-mvusb.c
+F:	drivers/net/mdio/mdio-mvusb.c
 
 MARVELL XENON MMC/SD/SDIO HOST CONTROLLER DRIVER
 M:	Hu Ziji <huziji@marvell.com>
@@ -15646,6 +15649,7 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/phy/phylink.c
 F:	drivers/net/phy/sfp*
+F:	include/linux/mdio/mdio-i2c.h
 F:	include/linux/phylink.h
 F:	include/linux/sfp.h
 K:	phylink\.h|struct\s+phylink|\.phylink|>phylink_|phylink_(autoneg|clear|connect|create|destroy|disconnect|ethtool|helper|mac|mii|of|set|start|stop|test|validate)
@@ -16730,8 +16734,8 @@ SYNOPSYS DESIGNWARE ETHERNET XPCS DRIVER
 M:	Jose Abreu <Jose.Abreu@synopsys.com>
 L:	netdev@vger.kernel.org
 S:	Supported
-F:	drivers/net/phy/mdio-xpcs.c
-F:	include/linux/mdio-xpcs.h
+F:	drivers/net/pcs/pcs-xpcs.c
+F:	include/linux/pcs/pcs-xpcs.h
 
 SYNOPSYS DESIGNWARE I2C DRIVER
 M:	Jarkko Nikula <jarkko.nikula@linux.intel.com>

drivers/net/Kconfig

@@ -473,6 +473,10 @@ config NET_SB1000
 
 source "drivers/net/phy/Kconfig"
 
+source "drivers/net/mdio/Kconfig"
+
+source "drivers/net/pcs/Kconfig"
+
 source "drivers/net/plip/Kconfig"
 
 source "drivers/net/ppp/Kconfig"

drivers/net/Makefile

@@ -21,6 +21,8 @@ obj-$(CONFIG_MDIO) += mdio.o
 obj-$(CONFIG_NET) += Space.o loopback.o
 obj-$(CONFIG_NETCONSOLE) += netconsole.o
 obj-y += phy/
+obj-y += mdio/
+obj-y += pcs/
 obj-$(CONFIG_RIONET) += rionet.o
 obj-$(CONFIG_NET_TEAM) += team/
 obj-$(CONFIG_TUN) += tun.o

drivers/net/ethernet/apm/xgene/xgene_enet_main.h

@@ -18,6 +18,7 @@
 #include <linux/of_platform.h>
 #include <linux/of_net.h>
 #include <linux/of_mdio.h>
+#include <linux/mdio/mdio-xgene.h>
 #include <linux/module.h>
 #include <net/ip.h>
 #include <linux/prefetch.h>
@@ -26,7 +27,6 @@
 #include "xgene_enet_hw.h"
 #include "xgene_enet_cle.h"
 #include "xgene_enet_ring2.h"
-#include "../../../phy/mdio-xgene.h"
 
 #define ETHER_MIN_PACKET	64
 #define ETHER_STD_PACKET	1518

drivers/net/ethernet/stmicro/stmmac/Kconfig

@@ -3,7 +3,7 @@ config STMMAC_ETH
 	tristate "STMicroelectronics Multi-Gigabit Ethernet driver"
 	depends on HAS_IOMEM && HAS_DMA
 	select MII
-	select MDIO_XPCS
+	select PCS_XPCS
 	select PAGE_POOL
 	select PHYLINK
 	select CRC32

drivers/net/ethernet/stmicro/stmmac/common.h

@@ -15,7 +15,7 @@
 #include <linux/netdevice.h>
 #include <linux/stmmac.h>
 #include <linux/phy.h>
-#include <linux/mdio-xpcs.h>
+#include <linux/pcs/pcs-xpcs.h>
 #include <linux/module.h>
 #if IS_ENABLED(CONFIG_VLAN_8021Q)
 #define STMMAC_VLAN_TAG_USED

drivers/net/mdio/Kconfig

+# SPDX-License-Identifier: GPL-2.0-only
+#
+# MDIO Layer Configuration
+#
+
+menuconfig MDIO_DEVICE
+	tristate "MDIO bus device drivers"
+	help
+	  MDIO devices and driver infrastructure code.
+
+if MDIO_DEVICE
+
+config MDIO_BUS
+	tristate
+	default m if PHYLIB=m
+	default MDIO_DEVICE
+	help
+	  This internal symbol is used for link time dependencies and it
+	  reflects whether the mdio_bus/mdio_device code is built as a
+	  loadable module or built-in.
+
+if MDIO_BUS
+
+config MDIO_DEVRES
+	tristate
+
+config MDIO_SUN4I
+	tristate "Allwinner sun4i MDIO interface support"
+	depends on ARCH_SUNXI || COMPILE_TEST
+	help
+	  This driver supports the MDIO interface found in the network
+	  interface units of the Allwinner SoC that have an EMAC (A10,
+	  A12, A10s, etc.)
+
+config MDIO_XGENE
+	tristate "APM X-Gene SoC MDIO bus controller"
+	depends on ARCH_XGENE || COMPILE_TEST
+	help
+	  This module provides a driver for the MDIO busses found in the
+	  APM X-Gene SoC's.
+
+config MDIO_ASPEED
+	tristate "ASPEED MDIO bus controller"
+	depends on ARCH_ASPEED || COMPILE_TEST
+	depends on OF_MDIO && HAS_IOMEM
+	help
+	  This module provides a driver for the independent MDIO bus
+	  controllers found in the ASPEED AST2600 SoC. This is a driver for the
+	  third revision of the ASPEED MDIO register interface - the first two
+	  revisions are the "old" and "new" interfaces found in the AST2400 and
+	  AST2500, embedded in the MAC. For legacy reasons, FTGMAC100 driver
+	  continues to drive the embedded MDIO controller for the AST2400 and
+	  AST2500 SoCs, so say N if AST2600 support is not required.
+
+config MDIO_BITBANG
+	tristate "Bitbanged MDIO buses"
+	help
+	  This module implements the MDIO bus protocol in software,
+	  for use by low level drivers that export the ability to
+	  drive the relevant pins.
+
+	  If in doubt, say N.
+
+config MDIO_BCM_IPROC
+	tristate "Broadcom iProc MDIO bus controller"
+	depends on ARCH_BCM_IPROC || COMPILE_TEST
+	depends on HAS_IOMEM && OF_MDIO
+	default ARCH_BCM_IPROC
+	help
+	  This module provides a driver for the MDIO busses found in the
+	  Broadcom iProc SoC's.
+
+config MDIO_BCM_UNIMAC
+	tristate "Broadcom UniMAC MDIO bus controller"
+	depends on HAS_IOMEM
+	help
+	  This module provides a driver for the Broadcom UniMAC MDIO busses.
+	  This hardware can be found in the Broadcom GENET Ethernet MAC
+	  controllers as well as some Broadcom Ethernet switches such as the
+	  Starfighter 2 switches.
+
+config MDIO_CAVIUM
+	tristate
+
+config MDIO_GPIO
+	tristate "GPIO lib-based bitbanged MDIO buses"
+	depends on MDIO_BITBANG
+	depends on GPIOLIB || COMPILE_TEST
+	help
+	  Supports GPIO lib-based MDIO busses.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called mdio-gpio.
+
+config MDIO_HISI_FEMAC
+	tristate "Hisilicon FEMAC MDIO bus controller"
+	depends on HAS_IOMEM && OF_MDIO
+	help
+	  This module provides a driver for the MDIO busses found in the
+	  Hisilicon SoC that have an Fast Ethernet MAC.
+
+config MDIO_I2C
+	tristate
+	depends on I2C
+	help
+	  Support I2C based PHYs.  This provides a MDIO bus bridged
+	  to I2C to allow PHYs connected in I2C mode to be accessed
+	  using the existing infrastructure.
+
+	  This is library mode.
+
+config MDIO_MVUSB
+	tristate "Marvell USB to MDIO Adapter"
+	depends on USB
+	select MDIO_DEVRES
+	help
+	  A USB to MDIO converter present on development boards for
+	  Marvell's Link Street family of Ethernet switches.
+
+config MDIO_MSCC_MIIM
+	tristate "Microsemi MIIM interface support"
+	depends on HAS_IOMEM
+	select MDIO_DEVRES
+	help
+	  This driver supports the MIIM (MDIO) interface found in the network
+	  switches of the Microsemi SoCs; it is recommended to switch on
+	  CONFIG_HIGH_RES_TIMERS
+
+config MDIO_MOXART
+	tristate "MOXA ART MDIO interface support"
+	depends on ARCH_MOXART || COMPILE_TEST
+	help
+	  This driver supports the MDIO interface found in the network
+	  interface units of the MOXA ART SoC
+
+config MDIO_OCTEON
+	tristate "Octeon and some ThunderX SOCs MDIO buses"
+	depends on (64BIT && OF_MDIO) || COMPILE_TEST
+	depends on HAS_IOMEM
+	select MDIO_CAVIUM
+	help
+	  This module provides a driver for the Octeon and ThunderX MDIO
+	  buses. It is required by the Octeon and ThunderX ethernet device
+	  drivers on some systems.
+
+config MDIO_IPQ4019
+	tristate "Qualcomm IPQ4019 MDIO interface support"
+	depends on HAS_IOMEM && OF_MDIO
+	help
+	  This driver supports the MDIO interface found in Qualcomm
+	  IPQ40xx series Soc-s.
+
+config MDIO_IPQ8064
+	tristate "Qualcomm IPQ8064 MDIO interface support"
+	depends on HAS_IOMEM && OF_MDIO
+	depends on MFD_SYSCON
+	help
+	  This driver supports the MDIO interface found in the network
+	  interface units of the IPQ8064 SoC
+
+config MDIO_THUNDER
+	tristate "ThunderX SOCs MDIO buses"
+	depends on 64BIT
+	depends on PCI
+	select MDIO_CAVIUM
+	help
+	  This driver supports the MDIO interfaces found on Cavium
+	  ThunderX SoCs when the MDIO bus device appears as a PCI
+	  device.
+
+comment "MDIO Multiplexers"
+
+config MDIO_BUS_MUX
+	tristate
+	depends on OF_MDIO
+	help
+	  This module provides a driver framework for MDIO bus
+	  multiplexers which connect one of several child MDIO busses
+	  to a parent bus.  Switching between child busses is done by
+	  device specific drivers.
+
+config MDIO_BUS_MUX_MESON_G12A
+	tristate "Amlogic G12a based MDIO bus multiplexer"
+	depends on ARCH_MESON || COMPILE_TEST
+	depends on OF_MDIO && HAS_IOMEM && COMMON_CLK
+	select MDIO_BUS_MUX
+	default m if ARCH_MESON
+	help
+	  This module provides a driver for the MDIO multiplexer/glue of
+	  the amlogic g12a SoC. The multiplexers connects either the external
+	  or the internal MDIO bus to the parent bus.
+
+config MDIO_BUS_MUX_BCM_IPROC
+	tristate "Broadcom iProc based MDIO bus multiplexers"
+	depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST)
+	select MDIO_BUS_MUX
+	default ARCH_BCM_IPROC
+	help
+	  This module provides a driver for MDIO bus multiplexers found in
+	  iProc based Broadcom SoCs. This multiplexer connects one of several
+	  child MDIO bus to a parent bus. Buses could be internal as well as
+	  external and selection logic lies inside the same multiplexer.
+
+config MDIO_BUS_MUX_GPIO
+	tristate "GPIO controlled MDIO bus multiplexers"
+	depends on OF_GPIO && OF_MDIO
+	select MDIO_BUS_MUX
+	help
+	  This module provides a driver for MDIO bus multiplexers that
+	  are controlled via GPIO lines.  The multiplexer connects one of
+	  several child MDIO busses to a parent bus.  Child bus
+	  selection is under the control of GPIO lines.
+
+config MDIO_BUS_MUX_MULTIPLEXER
+	tristate "MDIO bus multiplexer using kernel multiplexer subsystem"
+	depends on OF_MDIO
+	select MULTIPLEXER
+	select MDIO_BUS_MUX
+	help
+	  This module provides a driver for MDIO bus multiplexer
+	  that is controlled via the kernel multiplexer subsystem. The
+	  bus multiplexer connects one of several child MDIO busses to
+	  a parent bus.  Child bus selection is under the control of
+	  the kernel multiplexer subsystem.
+
+config MDIO_BUS_MUX_MMIOREG
+	tristate "MMIO device-controlled MDIO bus multiplexers"
+	depends on OF_MDIO && HAS_IOMEM
+	select MDIO_BUS_MUX
+	help
+	  This module provides a driver for MDIO bus multiplexers that
+	  are controlled via a simple memory-mapped device, like an FPGA.
+	  The multiplexer connects one of several child MDIO busses to a
+	  parent bus.  Child bus selection is under the control of one of
+	  the FPGA's registers.
+
+	  Currently, only 8/16/32 bits registers are supported.
+
+
+endif
+endif

drivers/net/mdio/Makefile

+# SPDX-License-Identifier: GPL-2.0
+# Makefile for Linux MDIO bus drivers
+
+obj-$(CONFIG_MDIO_ASPEED)		+= mdio-aspeed.o
+obj-$(CONFIG_MDIO_BCM_IPROC)		+= mdio-bcm-iproc.o
+obj-$(CONFIG_MDIO_BCM_UNIMAC)		+= mdio-bcm-unimac.o
+obj-$(CONFIG_MDIO_BITBANG)		+= mdio-bitbang.o
+obj-$(CONFIG_MDIO_CAVIUM)		+= mdio-cavium.o
+obj-$(CONFIG_MDIO_GPIO)			+= mdio-gpio.o
+obj-$(CONFIG_MDIO_HISI_FEMAC)		+= mdio-hisi-femac.o
+obj-$(CONFIG_MDIO_I2C)			+= mdio-i2c.o
+obj-$(CONFIG_MDIO_IPQ4019)		+= mdio-ipq4019.o
+obj-$(CONFIG_MDIO_IPQ8064)		+= mdio-ipq8064.o
+obj-$(CONFIG_MDIO_MOXART)		+= mdio-moxart.o
+obj-$(CONFIG_MDIO_MSCC_MIIM)		+= mdio-mscc-miim.o
+obj-$(CONFIG_MDIO_MVUSB)		+= mdio-mvusb.o
+obj-$(CONFIG_MDIO_OCTEON)		+= mdio-octeon.o
+obj-$(CONFIG_MDIO_SUN4I)		+= mdio-sun4i.o
+obj-$(CONFIG_MDIO_THUNDER)		+= mdio-thunder.o
+obj-$(CONFIG_MDIO_XGENE)		+= mdio-xgene.o
+
+obj-$(CONFIG_MDIO_BUS_MUX)		+= mdio-mux.o
+obj-$(CONFIG_MDIO_BUS_MUX_BCM_IPROC)	+= mdio-mux-bcm-iproc.o
+obj-$(CONFIG_MDIO_BUS_MUX_GPIO)		+= mdio-mux-gpio.o
+obj-$(CONFIG_MDIO_BUS_MUX_MESON_G12A)	+= mdio-mux-meson-g12a.o
+obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) 	+= mdio-mux-mmioreg.o
+obj-$(CONFIG_MDIO_BUS_MUX_MULTIPLEXER) 	+= mdio-mux-multiplexer.o

drivers/net/phy/mdio-i2c.c → drivers/net/mdio/mdio-i2c.c

@@ -10,10 +10,9 @@
  * of their settings.
  */
 #include <linux/i2c.h>
+#include <linux/mdio/mdio-i2c.h>
 #include <linux/phy.h>
 
-#include "mdio-i2c.h"
-
 /*
  * I2C bus addresses 0x50 and 0x51 are normally an EEPROM, which is
  * specified to be present in SFP modules.  These correspond with PHY

drivers/net/phy/mdio-xgene.c → drivers/net/mdio/mdio-xgene.c

@@ -11,6 +11,7 @@
 #include <linux/efi.h>
 #include <linux/if_vlan.h>
 #include <linux/io.h>
+#include <linux/mdio/mdio-xgene.h>
 #include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/of_net.h>
@@ -18,7 +19,6 @@
 #include <linux/prefetch.h>
 #include <linux/phy.h>
 #include <net/ip.h>
-#include "mdio-xgene.h"
 
 static bool xgene_mdio_status;
 

drivers/net/pcs/Kconfig

+# SPDX-License-Identifier: GPL-2.0-only
+#
+# PCS Layer Configuration
+#
+
+menu "PCS device drivers"
+
+config PCS_XPCS
+	tristate "Synopsys DesignWare XPCS controller"
+	select MDIO_BUS
+	depends on MDIO_DEVICE
+	help
+	  This module provides helper functions for Synopsys DesignWare XPCS
+	  controllers.
+
+endmenu

drivers/net/pcs/Makefile

+# SPDX-License-Identifier: GPL-2.0
+# Makefile for Linux PCS drivers
+
+obj-$(CONFIG_PCS_XPCS)		+= pcs-xpcs.o

drivers/net/phy/mdio-xpcs.c → drivers/net/pcs/pcs-xpcs.c

@@ -7,8 +7,8 @@
  */
 
 #include <linux/delay.h>
+#include <linux/pcs/pcs-xpcs.h>
 #include <linux/mdio.h>
-#include <linux/mdio-xpcs.h>
 #include <linux/phylink.h>
 #include <linux/workqueue.h>
 

drivers/net/phy/Makefile

 # SPDX-License-Identifier: GPL-2.0
-# Makefile for Linux PHY drivers and MDIO bus drivers
+# Makefile for Linux PHY drivers
 
 libphy-y			:= phy.o phy-c45.o phy-core.o phy_device.o \
 				   linkmode.o
@@ -24,31 +24,6 @@ libphy-$(CONFIG_LED_TRIGGER_PHY)	+= phy_led_triggers.o
 obj-$(CONFIG_PHYLINK)		+= phylink.o
 obj-$(CONFIG_PHYLIB)		+= libphy.o
 
-obj-$(CONFIG_MDIO_ASPEED)	+= mdio-aspeed.o
-obj-$(CONFIG_MDIO_BCM_IPROC)	+= mdio-bcm-iproc.o
-obj-$(CONFIG_MDIO_BCM_UNIMAC)	+= mdio-bcm-unimac.o
-obj-$(CONFIG_MDIO_BITBANG)	+= mdio-bitbang.o
-obj-$(CONFIG_MDIO_BUS_MUX)	+= mdio-mux.o
-obj-$(CONFIG_MDIO_BUS_MUX_BCM_IPROC)	+= mdio-mux-bcm-iproc.o
-obj-$(CONFIG_MDIO_BUS_MUX_GPIO)	+= mdio-mux-gpio.o
-obj-$(CONFIG_MDIO_BUS_MUX_MESON_G12A)	+= mdio-mux-meson-g12a.o
-obj-$(CONFIG_MDIO_BUS_MUX_MMIOREG) += mdio-mux-mmioreg.o
-obj-$(CONFIG_MDIO_BUS_MUX_MULTIPLEXER) += mdio-mux-multiplexer.o
-obj-$(CONFIG_MDIO_CAVIUM)	+= mdio-cavium.o
-obj-$(CONFIG_MDIO_GPIO)		+= mdio-gpio.o
-obj-$(CONFIG_MDIO_HISI_FEMAC)	+= mdio-hisi-femac.o
-obj-$(CONFIG_MDIO_I2C)		+= mdio-i2c.o
-obj-$(CONFIG_MDIO_IPQ4019)	+= mdio-ipq4019.o
-obj-$(CONFIG_MDIO_IPQ8064)	+= mdio-ipq8064.o
-obj-$(CONFIG_MDIO_MOXART)	+= mdio-moxart.o
-obj-$(CONFIG_MDIO_MSCC_MIIM)	+= mdio-mscc-miim.o
-obj-$(CONFIG_MDIO_MVUSB)	+= mdio-mvusb.o
-obj-$(CONFIG_MDIO_OCTEON)	+= mdio-octeon.o
-obj-$(CONFIG_MDIO_SUN4I)	+= mdio-sun4i.o
-obj-$(CONFIG_MDIO_THUNDER)	+= mdio-thunder.o
-obj-$(CONFIG_MDIO_XGENE)	+= mdio-xgene.o
-obj-$(CONFIG_MDIO_XPCS)		+= mdio-xpcs.o
-
 obj-$(CONFIG_NETWORK_PHY_TIMESTAMPING) += mii_timestamper.o
 
 obj-$(CONFIG_SFP)		+= sfp.o
@@ -62,32 +37,32 @@ ifdef CONFIG_HWMON
 aquantia-objs			+= aquantia_hwmon.o
 endif
 obj-$(CONFIG_AQUANTIA_PHY)	+= aquantia.o
-obj-$(CONFIG_AX88796B_PHY)	+= ax88796b.o
 obj-$(CONFIG_AT803X_PHY)	+= at803x.o
+obj-$(CONFIG_AX88796B_PHY)	+= ax88796b.o
+obj-$(CONFIG_BCM54140_PHY)	+= bcm54140.o
 obj-$(CONFIG_BCM63XX_PHY)	+= bcm63xx.o
 obj-$(CONFIG_BCM7XXX_PHY)	+= bcm7xxx.o
+obj-$(CONFIG_BCM84881_PHY)	+= bcm84881.o
 obj-$(CONFIG_BCM87XX_PHY)	+= bcm87xx.o
 obj-$(CONFIG_BCM_CYGNUS_PHY)	+= bcm-cygnus.o
 obj-$(CONFIG_BCM_NET_PHYLIB)	+= bcm-phy-lib.o
 obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
-obj-$(CONFIG_BCM54140_PHY)	+= bcm54140.o
-obj-$(CONFIG_BCM84881_PHY)	+= bcm84881.o
 obj-$(CONFIG_CICADA_PHY)	+= cicada.o
 obj-$(CONFIG_CORTINA_PHY)	+= cortina.o
 obj-$(CONFIG_DAVICOM_PHY)	+= davicom.o
 obj-$(CONFIG_DP83640_PHY)	+= dp83640.o
 obj-$(CONFIG_DP83822_PHY)	+= dp83822.o
-obj-$(CONFIG_DP83TC811_PHY)	+= dp83tc811.o
 obj-$(CONFIG_DP83848_PHY)	+= dp83848.o
 obj-$(CONFIG_DP83867_PHY)	+= dp83867.o
 obj-$(CONFIG_DP83869_PHY)	+= dp83869.o
+obj-$(CONFIG_DP83TC811_PHY)	+= dp83tc811.o
 obj-$(CONFIG_FIXED_PHY)		+= fixed_phy.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_INTEL_XWAY_PHY)	+= intel-xway.o
 obj-$(CONFIG_LSI_ET1011C_PHY)	+= et1011c.o
 obj-$(CONFIG_LXT_PHY)		+= lxt.o
-obj-$(CONFIG_MARVELL_PHY)	+= marvell.o
 obj-$(CONFIG_MARVELL_10G_PHY)	+= marvell10g.o
+obj-$(CONFIG_MARVELL_PHY)	+= marvell.o
 obj-$(CONFIG_MESON_GXL_PHY)	+= meson-gxl.o
 obj-$(CONFIG_MICREL_KS8995MA)	+= spi_ks8995.o
 obj-$(CONFIG_MICREL_PHY)	+= micrel.o

drivers/net/phy/sfp.c

@@ -7,6 +7,7 @@
 #include <linux/i2c.h>
 #include <linux/interrupt.h>
 #include <linux/jiffies.h>
+#include <linux/mdio/mdio-i2c.h>
 #include <linux/module.h>
 #include <linux/mutex.h>
 #include <linux/of.h>
@@ -16,7 +17,6 @@
 #include <linux/slab.h>
 #include <linux/workqueue.h>
 
-#include "mdio-i2c.h"
 #include "sfp.h"
 #include "swphy.h"
 

include/linux/mdio-xpcs.h → include/linux/pcs/pcs-xpcs.h

@@ -4,8 +4,8 @@
  * Synopsys DesignWare XPCS helpers
  */
 
-#ifndef __LINUX_MDIO_XPCS_H
-#define __LINUX_MDIO_XPCS_H
+#ifndef __LINUX_PCS_XPCS_H
+#define __LINUX_PCS_XPCS_H
 
 #include <linux/phy.h>
 #include <linux/phylink.h>
@@ -29,7 +29,7 @@ struct mdio_xpcs_ops {
 	int (*probe)(struct mdio_xpcs_args *xpcs, phy_interface_t interface);
 };
 
-#if IS_ENABLED(CONFIG_MDIO_XPCS)
+#if IS_ENABLED(CONFIG_PCS_XPCS)
 struct mdio_xpcs_ops *mdio_xpcs_get_ops(void);
 #else
 static inline struct mdio_xpcs_ops *mdio_xpcs_get_ops(void)
@@ -38,4 +38,4 @@ static inline struct mdio_xpcs_ops *mdio_xpcs_get_ops(void)
 }
 #endif
 
-#endif /* __LINUX_MDIO_XPCS_H */
+#endif /* __LINUX_PCS_XPCS_H */