Commit efe20b42 authored by Arnd Bergmann's avatar Arnd Bergmann

Merge branches 'samsung/exynos-dt2' and 'samsung/s3c24xx-dt2' into next/drivers

This is the merge base for samsung/common-clk-audio
Signed-off-by: default avatarArnd Bergmann <arnd@arndb.de>
......@@ -102,6 +102,7 @@ Exynos4 SoC and this is specified where applicable.
sclk_spi0_isp 174 Exynos4x12
sclk_spi1_isp 175 Exynos4x12
sclk_uart_isp 176 Exynos4x12
sclk_fimg2d 177
[Peripheral Clock Gates]
......@@ -129,7 +130,7 @@ Exynos4 SoC and this is specified where applicable.
smmu_mfcl 274
smmu_mfcr 275
g3d 276
g2d 277 Exynos4210
g2d 277
rotator 278 Exynos4210
mdma 279 Exynos4210
smmu_g2d 280 Exynos4210
......
......@@ -10,11 +10,16 @@ Required properties:
mapped region.
- interrupts : G2D interrupt number to the CPU.
- clocks : from common clock binding: handle to G2D clocks.
- clock-names : from common clock binding: must contain "sclk_fimg2d" and
"fimg2d", corresponding to entries in the clocks property.
Example:
g2d@12800000 {
compatible = "samsung,s5pv210-g2d";
reg = <0x12800000 0x1000>;
interrupts = <0 89 0>;
clocks = <&clock 177>, <&clock 277>;
clock-names = "sclk_fimg2d", "fimg2d";
status = "disabled";
};
......@@ -15,6 +15,9 @@ Required properties:
mapped region.
- interrupts : MFC interrupt number to the CPU.
- clocks : from common clock binding: handle to mfc clocks.
- clock-names : from common clock binding: must contain "sclk_mfc" and "mfc",
corresponding to entries in the clocks property.
- samsung,mfc-r : Base address of the first memory bank used by MFC
for DMA contiguous memory allocation and its size.
......@@ -34,6 +37,8 @@ mfc: codec@13400000 {
reg = <0x13400000 0x10000>;
interrupts = <0 94 0>;
samsung,power-domain = <&pd_mfc>;
clocks = <&clock 170>, <&clock 273>;
clock-names = "sclk_mfc", "mfc";
};
Board specific DT entry:
......
......@@ -25,8 +25,18 @@ Required Properties:
- gpio-controller: identifies the node as a gpio controller and pin bank.
- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
binding is used, the amount of cells must be specified as 2. See generic
GPIO binding documentation for description of particular cells.
binding is used, the amount of cells must be specified as 2. See the below
mentioned gpio binding representation for description of particular cells.
Eg: <&gpx2 6 0>
<[phandle of the gpio controller node]
[pin number within the gpio controller]
[flags]>
Values for gpio specifier:
- Pin number: is a value between 0 to 7.
- Flags: 0 - Active High
1 - Active Low
- Pin mux/config groups as child nodes: The pin mux (selecting pin function
mode) and pin config (pull up/down, driver strength) settings are represented
......@@ -274,3 +284,33 @@ Example 4: Set up the default pin state for uart controller.
pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
}
Example 5: A display port client node that supports 'default' pinctrl state
and gpio binding.
display-port-controller {
/* ... */
samsung,hpd-gpio = <&gpx2 6 0>;
pinctrl-names = "default";
pinctrl-0 = <&dp_hpd>;
};
Example 6: Request the gpio for display port controller
static int exynos_dp_probe(struct platform_device *pdev)
{
int hpd_gpio, ret;
struct device *dev = &pdev->dev;
struct device_node *dp_node = dev->of_node;
/* ... */
hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0);
/* ... */
ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN,
"hpd_gpio");
/* ... */
}
......@@ -48,3 +48,37 @@ Example:
clocks = <&clock 285>;
clock-names = "usbhost";
};
DWC3
Required properties:
- compatible: should be "samsung,exynos5250-dwusb3" for USB 3.0 DWC3
controller.
- #address-cells, #size-cells : should be '1' if the device has sub-nodes
with 'reg' property.
- ranges: allows valid 1:1 translation between child's address space and
parent's address space
- clocks: Clock IDs array as required by the controller.
- clock-names: names of clocks correseponding to IDs in the clock property
Sub-nodes:
The dwc3 core should be added as subnode to Exynos dwc3 glue.
- dwc3 :
The binding details of dwc3 can be found in:
Documentation/devicetree/bindings/usb/dwc3.txt
Example:
usb@12000000 {
compatible = "samsung,exynos5250-dwusb3";
clocks = <&clock 286>;
clock-names = "usbdrd30";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dwc3 {
compatible = "synopsys,dwc3";
reg = <0x12000000 0x10000>;
interrupts = <0 72 0>;
usb-phy = <&usb2_phy &usb3_phy>;
};
};
......@@ -21,6 +21,10 @@ Required properties for dp-controller:
of memory mapped region.
-interrupts:
interrupt combiner values.
-clocks:
from common clock binding: handle to dp clock.
-clock-names:
from common clock binding: Shall be "dp".
-interrupt-parent:
phandle to Interrupt combiner node.
-samsung,color-space:
......@@ -61,6 +65,8 @@ SOC specific portion:
reg = <0x145b0000 0x10000>;
interrupts = <10 3>;
interrupt-parent = <&combiner>;
clocks = <&clock 342>;
clock-names = "dp";
dptx-phy {
reg = <0x10040720>;
......
......@@ -159,6 +159,7 @@ dtb-$(CONFIG_ARCH_U8500) += snowball.dtb \
hrefprev60.dtb \
hrefv60plus.dtb \
ccu9540.dtb
dtb-$(CONFIG_ARCH_S3C24XX) += s3c2416-smdk2416.dtb
dtb-$(CONFIG_ARCH_SHMOBILE) += emev2-kzm9d.dtb \
r8a7740-armadillo800eva.dtb \
r8a7778-bockw.dtb \
......
......@@ -160,6 +160,8 @@ mfc: codec@13400000 {
reg = <0x13400000 0x10000>;
interrupts = <0 94 0>;
samsung,power-domain = <&pd_mfc>;
clocks = <&clock 170>, <&clock 273>;
clock-names = "sclk_mfc", "mfc";
status = "disabled";
};
......
......@@ -41,6 +41,10 @@ mmc_reg: voltage-regulator {
enable-active-high;
};
tmu@100C0000 {
status = "okay";
};
sdhci@12530000 {
bus-width = <4>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
......@@ -83,6 +87,150 @@ serial@13830000 {
status = "okay";
};
i2c@13860000 {
status = "okay";
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <20000>;
pinctrl-0 = <&i2c0_bus>;
pinctrl-names = "default";
max8997_pmic@66 {
compatible = "maxim,max8997-pmic";
reg = <0x66>;
interrupt-parent = <&gpx0>;
interrupts = <4 0>, <3 0>;
max8997,pmic-buck1-dvs-voltage = <1350000>;
max8997,pmic-buck2-dvs-voltage = <1100000>;
max8997,pmic-buck5-dvs-voltage = <1200000>;
regulators {
ldo1_reg: LDO1 {
regulator-name = "VDD_ABB_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
ldo2_reg: LDO2 {
regulator-name = "VDD_ALIVE_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
ldo3_reg: LDO3 {
regulator-name = "VMIPI_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
};
ldo4_reg: LDO4 {
regulator-name = "VDD_RTC_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo6_reg: LDO6 {
regulator-name = "VMIPI_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo7_reg: LDO7 {
regulator-name = "VDD_AUD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
ldo8_reg: LDO8 {
regulator-name = "VADC_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
ldo9_reg: LDO9 {
regulator-name = "DVDD_SWB_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
ldo10_reg: LDO10 {
regulator-name = "VDD_PLL_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
ldo11_reg: LDO11 {
regulator-name = "VDD_AUD_3V";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
ldo14_reg: LDO14 {
regulator-name = "AVDD18_SWB_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo17_reg: LDO17 {
regulator-name = "VDD_SWB_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
ldo21_reg: LDO21 {
regulator-name = "VDD_MIF_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
buck1_reg: BUCK1 {
regulator-name = "VDD_ARM_1.2V";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
buck2_reg: BUCK2 {
regulator-name = "VDD_INT_1.1V";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
regulator-boot-on;
};
buck3_reg: BUCK3 {
regulator-name = "VDD_G3D_1.1V";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1100000>;
};
buck5_reg: BUCK5 {
regulator-name = "VDDQ_M1M2_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
};
buck7_reg: BUCK7 {
regulator-name = "VDD_LCD_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
};
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
......@@ -143,4 +291,25 @@ xusbxti {
clock-frequency = <24000000>;
};
};
fimd@11c00000 {
pinctrl-0 = <&lcd_en &lcd_clk &lcd_data24 &pwm0_out>;
pinctrl-names = "default";
status = "okay";
};
display-timings {
native-mode = <&timing0>;
timing0: timing {
clock-frequency = <50000>;
hactive = <1024>;
vactive = <600>;
hfront-porch = <64>;
hback-porch = <16>;
hsync-len = <48>;
vback-porch = <64>;
vfront-porch = <16>;
vsync-len = <3>;
};
};
};
......@@ -330,6 +330,95 @@ i2c1_bus: i2c1-bus {
samsung,pin-pud = <3>;
samsung,pin-drv = <0>;
};
pwm0_out: pwm0-out {
samsung,pins = "gpd0-0";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
pwm1_out: pwm1-out {
samsung,pins = "gpd0-1";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
pwm2_out: pwm2-out {
samsung,pins = "gpd0-2";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
pwm3_out: pwm3-out {
samsung,pins = "gpd0-3";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_ctrl: lcd-ctrl {
samsung,pins = "gpd0-0", "gpd0-1";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_sync: lcd-sync {
samsung,pins = "gpf0-0", "gpf0-1";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_en: lcd-en {
samsung,pins = "gpe3-4";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_clk: lcd-clk {
samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_data16: lcd-data-width16 {
samsung,pins = "gpf0-7", "gpf1-0", "gpf1-1", "gpf1-2",
"gpf1-3", "gpf1-6", "gpf1-7", "gpf2-0",
"gpf2-1", "gpf2-2", "gpf2-3", "gpf2-7",
"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_data18: lcd-data-width18 {
samsung,pins = "gpf0-6", "gpf0-7", "gpf1-0", "gpf1-1",
"gpf1-2", "gpf1-3", "gpf1-6", "gpf1-7",
"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
"gpf2-6", "gpf2-7", "gpf3-0", "gpf3-1",
"gpf3-2", "gpf3-3";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
lcd_data24: lcd-data-width24 {
samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
"gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7",
"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
pinctrl@11000000 {
......
......@@ -112,12 +112,17 @@ tmu@100C0000 {
interrupt-parent = <&combiner>;
reg = <0x100C0000 0x100>;
interrupts = <2 4>;
clocks = <&clock 383>;
clock-names = "tmu_apbif";
status = "disabled";
};
g2d@12800000 {
compatible = "samsung,s5pv210-g2d";
reg = <0x12800000 0x1000>;
interrupts = <0 89 0>;
clocks = <&clock 177>, <&clock 277>;
clock-names = "sclk_fimg2d", "fimg2d";
status = "disabled";
};
};
......@@ -43,6 +43,7 @@ mshc@12550000 {
#size-cells = <0>;
pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
pinctrl-names = "default";
vmmc-supply = <&ldo20_reg &buck8_reg>;
status = "okay";
num-slots = <1>;
......@@ -78,6 +79,7 @@ sdhci@12530000 {
bus-width = <4>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
pinctrl-names = "default";
vmmc-supply = <&ldo4_reg &ldo21_reg>;
status = "okay";
};
......@@ -108,4 +110,199 @@ xusbxti {
clock-frequency = <24000000>;
};
};
i2c@13860000 {
pinctrl-0 = <&i2c0_bus>;
pinctrl-names = "default";
status = "okay";
max77686: pmic@09 {
compatible = "maxim,max77686";
reg = <0x09>;
voltage-regulators {
ldo1_reg: LDO1 {
regulator-name = "VDD_ALIVE_1.0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
ldo2_reg: LDO2 {
regulator-name = "VDDQ_M1_2_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo3_reg: LDO3 {
regulator-name = "VDDQ_EXT_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo4_reg: LDO4 {
regulator-name = "VDDQ_MMC2_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
regulator-boot-on;
};
ldo5_reg: LDO5 {
regulator-name = "VDDQ_MMC1_3_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo6_reg: LDO6 {
regulator-name = "VDD10_MPLL_1.0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
ldo7_reg: LDO7 {
regulator-name = "VDD10_XPLL_1.0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
};
ldo11_reg: LDO11 {
regulator-name = "VDD18_ABB1_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
ldo12_reg: LDO12 {
regulator-name = "VDD33_USB_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
};
ldo13_reg: LDO13 {
regulator-name = "VDDQ_C2C_W_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo14_reg: LDO14 {
regulator-name = "VDD18_ABB0_2_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo15_reg: LDO15 {
regulator-name = "VDD10_HSIC_1.0V";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
regulator-boot-on;
};
ldo16_reg: LDO16 {
regulator-name = "VDD18_HSIC_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
ldo20_reg: LDO20 {
regulator-name = "LDO20_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-boot-on;
};
ldo21_reg: LDO21 {
regulator-name = "LDO21_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
};
ldo25_reg: LDO25 {
regulator-name = "VDDQ_LCD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
regulator-boot-on;
};
buck1_reg: BUCK1 {
regulator-name = "vdd_mif";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
regulator-boot-on;
};
buck2_reg: BUCK2 {
regulator-name = "vdd_arm";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1300000>;
regulator-always-on;
regulator-boot-on;
};
buck3_reg: BUCK3 {
regulator-name = "vdd_int";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
regulator-boot-on;
};
buck4_reg: BUCK4 {
regulator-name = "vdd_g3d";
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1100000>;
regulator-microvolt-offset = <50000>;
};
buck5_reg: BUCK5 {
regulator-name = "VDDQ_CKEM1_2_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
regulator-boot-on;
};
buck6_reg: BUCK6 {
regulator-name = "BUCK6_1.35V";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
buck7_reg: BUCK7 {
regulator-name = "BUCK7_2.0V";
regulator-min-microvolt = <2000000>;
regulator-max-microvolt = <2000000>;
regulator-always-on;
};
buck8_reg: BUCK8 {
regulator-name = "BUCK8_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
};
};
};
};
};
......@@ -36,6 +36,72 @@ mmc_reg: voltage-regulator {
enable-active-high;
};
pinctrl@11000000 {
keypad_rows: keypad-rows {
samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
samsung,pin-function = <3>;
samsung,pin-pud = <3>;
samsung,pin-drv = <0>;
};
keypad_cols: keypad-cols {
samsung,pins = "gpx1-0", "gpx1-1";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
keypad@100A0000 {
samsung,keypad-num-rows = <3>;
samsung,keypad-num-columns = <2>;
linux,keypad-no-autorepeat;
linux,keypad-wakeup;
pinctrl-0 = <&keypad_rows &keypad_cols>;
pinctrl-names = "default";
status = "okay";
key_home {
keypad,row = <0>;
keypad,column = <0>;
linux,code = <102>;
};
key_down {
keypad,row = <0>;
keypad,column = <1>;
linux,code = <108>;
};
key_up {
keypad,row = <1>;
keypad,column = <0>;
linux,code = <103>;
};
key_menu {
keypad,row = <1>;
keypad,column = <1>;
linux,code = <139>;
};
key_back {
keypad,row = <2>;
keypad,column = <0>;
linux,code = <158>;
};
key_enter {
keypad,row = <2>;
keypad,column = <1>;
linux,code = <28>;
};
};
g2d@10800000 {
status = "okay";
};
sdhci@12530000 {
bus-width = <4>;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sd2_cd>;
......
......@@ -31,8 +31,91 @@ g2d@10800000 {
status = "okay";
};
g2d@10800000 {
pinctrl@11000000 {
keypad_rows: keypad-rows {
samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
samsung,pin-function = <3>;
samsung,pin-pud = <3>;
samsung,pin-drv = <0>;
};
keypad_cols: keypad-cols {
samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
"gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
keypad@100A0000 {
samsung,keypad-num-rows = <3>;
samsung,keypad-num-columns = <8>;
linux,keypad-no-autorepeat;
linux,keypad-wakeup;
pinctrl-0 = <&keypad_rows &keypad_cols>;
pinctrl-names = "default";
status = "okay";
key_1 {
keypad,row = <1>;
keypad,column = <3>;
linux,code = <2>;
};
key_2 {
keypad,row = <1>;
keypad,column = <4>;
linux,code = <3>;
};
key_3 {
keypad,row = <1>;
keypad,column = <5>;
linux,code = <4>;
};
key_4 {
keypad,row = <1>;
keypad,column = <6>;
linux,code = <5>;
};
key_5 {
keypad,row = <1>;
keypad,column = <7>;
linux,code = <6>;
};
key_A {
keypad,row = <2>;
keypad,column = <6>;
linux,code = <30>;
};
key_B {
keypad,row = <2>;
keypad,column = <7>;
linux,code = <48>;
};
key_C {
keypad,row = <0>;
keypad,column = <5>;
linux,code = <46>;
};
key_D {
keypad,row = <2>;
keypad,column = <5>;
linux,code = <32>;
};
key_E {
keypad,row = <0>;
keypad,column = <7>;
linux,code = <18>;
};
};
sdhci@12530000 {
......
......@@ -778,62 +778,6 @@ sd3_bus4: sd3-bus-width4 {
samsung,pin-drv = <3>;
};
keypad_col0: keypad-col0 {
samsung,pins = "gpl2-0";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col1: keypad-col1 {
samsung,pins = "gpl2-1";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col2: keypad-col2 {
samsung,pins = "gpl2-2";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col3: keypad-col3 {
samsung,pins = "gpl2-3";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col4: keypad-col4 {
samsung,pins = "gpl2-4";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col5: keypad-col5 {
samsung,pins = "gpl2-5";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col6: keypad-col6 {
samsung,pins = "gpl2-6";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
keypad_col7: keypad-col7 {
samsung,pins = "gpl2-7";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
cam_port_b: cam-port-b {
samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
......
......@@ -28,14 +28,6 @@ aliases {
pinctrl3 = &pinctrl_3;
};
combiner:interrupt-controller@10440000 {
interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
<0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
<0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
<0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>,
<0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>;
};
clock: clock-controller@0x10030000 {
compatible = "samsung,exynos4412-clock";
reg = <0x10030000 0x20000>;
......@@ -77,6 +69,8 @@ g2d@10800000 {
compatible = "samsung,exynos4212-g2d";
reg = <0x10800000 0x1000>;
interrupts = <0 89 0>;
clocks = <&clock 177>, <&clock 277>;
clock-names = "sclk_fimg2d", "fimg2d";
status = "disabled";
};
};
......@@ -449,4 +449,35 @@ xxti {
clock-frequency = <24000000>;
};
};
dp-controller {
samsung,color-space = <0>;
samsung,dynamic-range = <0>;
samsung,ycbcr-coeff = <0>;
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <4>;
};
fimd: fimd@14400000 {
display-timings {
native-mode = <&timing0>;
timing0: timing@0 {
/* 2560x1600 DP panel */
clock-frequency = <50000>;
hactive = <2560>;
vactive = <1600>;
hfront-porch = <48>;
hback-porch = <80>;
hsync-len = <32>;
vback-porch = <16>;
vfront-porch = <8>;
vsync-len = <6>;
};
};
};
rtc {
status = "okay";
};
};
......@@ -553,6 +553,13 @@ uart1_fctl: uart1-fctl {
samsung,pin-pud = <0>;
samaung,pin-drv = <0>;
};
dp_hpd: dp_hpd {
samsung,pins = "gpx0-7";
samsung,pin-function = <3>;
samsung,pin-pud = <0>;
samaung,pin-drv = <0>;
};
};
pinctrl@13400000 {
......
......@@ -37,6 +37,30 @@ eeprom@50 {
};
};
vdd:fixed-regulator@0 {
compatible = "regulator-fixed";
regulator-name = "vdd-supply";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
dbvdd:fixed-regulator@1 {
compatible = "regulator-fixed";
regulator-name = "dbvdd-supply";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
spkvdd:fixed-regulator@2 {
compatible = "regulator-fixed";
regulator-name = "spkvdd-supply";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
regulator-always-on;
};
i2c@12C70000 {
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <20000>;
......@@ -47,8 +71,17 @@ eeprom@51 {
};
wm8994: wm8994@1a {
compatible = "wlf,wm8994";
reg = <0x1a>;
compatible = "wlf,wm8994";
reg = <0x1a>;
gpio-controller;
#gpio-cells = <2>;
AVDD2-supply = <&vdd>;
CPVDD-supply = <&vdd>;
DBVDD-supply = <&dbvdd>;
SPKVDD1-supply = <&spkvdd>;
SPKVDD2-supply = <&spkvdd>;
};
};
......@@ -224,6 +257,9 @@ dp-controller {
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <4>;
pinctrl-names = "default";
pinctrl-0 = <&dp_hpd>;
};
display-timings {
......
......@@ -171,6 +171,10 @@ keyboard-controller {
};
};
rtc {
status = "okay";
};
/*
* On Snow we've got SIP WiFi and so can keep drive strengths low to
* reduce EMI.
......
......@@ -479,6 +479,36 @@ i2s2: i2s@12D70000 {
pinctrl-0 = <&i2s2_bus>;
};
usb@12000000 {
compatible = "samsung,exynos5250-dwusb3";
clocks = <&clock 286>;
clock-names = "usbdrd30";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dwc3 {
compatible = "synopsys,dwc3";
reg = <0x12000000 0x10000>;
interrupts = <0 72 0>;
usb-phy = <&usb2_phy &usb3_phy>;
};
};
usb3_phy: usbphy@12100000 {
compatible = "samsung,exynos5250-usb3phy";
reg = <0x12100000 0x100>;
clocks = <&clock 1>, <&clock 286>;
clock-names = "ext_xtal", "usbdrd30";
#address-cells = <1>;
#size-cells = <1>;
ranges;
usbphy-sys {
reg = <0x10040704 0x8>;
};
};
usb@12110000 {
compatible = "samsung,exynos4210-ehci";
reg = <0x12110000 0x100>;
......@@ -497,7 +527,7 @@ usb@12120000 {
clock-names = "usbhost";
};
usbphy@12130000 {
usb2_phy: usbphy@12130000 {
compatible = "samsung,exynos5250-usb2phy";
reg = <0x12130000 0x100>;
clocks = <&clock 1>, <&clock 285>;
......@@ -621,6 +651,8 @@ dp-controller {
reg = <0x145b0000 0x1000>;
interrupts = <10 3>;
interrupt-parent = <&combiner>;
clocks = <&clock 342>;
clock-names = "dp";
#address-cells = <1>;
#size-cells = <0>;
......
......@@ -17,7 +17,7 @@ / {
compatible = "samsung,sd5v1", "samsung,exynos5440";
chosen {
bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200";
};
fixed-rate-clocks {
......
......@@ -17,11 +17,46 @@ / {
compatible = "samsung,ssdk5440", "samsung,exynos5440";
chosen {
bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 console=ttySAC0,115200";
bootargs = "root=/dev/sda2 rw rootwait ignore_loglevel early_printk no_console_suspend mem=2048M@0x80000000 mem=6144M@0x100000000 console=ttySAC0,115200";
};
spi {
status = "disabled";
spi_0: spi@D0000 {
flash: w25q128@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "winbond,w25q128";
spi-max-frequency = <15625000>;
reg = <0>;
controller-data {
samsung,spi-feedback-delay = <0>;
};
partition@00000 {
label = "BootLoader";
reg = <0x60000 0x80000>;
read-only;
};
partition@e0000 {
label = "Recovery-Kernel";
reg = <0xe0000 0x300000>;
read-only;
};
partition@3e0000 {
label = "CRAM-FS";
reg = <0x3e0000 0x700000>;
read-only;
};
partition@ae0000 {
label = "User-Data";
reg = <0xae0000 0x520000>;
};
};
};
fixed-rate-clocks {
......
......@@ -16,6 +16,10 @@ / {
interrupt-parent = <&gic>;
aliases {
spi0 = &spi_0;
};
clock: clock-controller@0x160000 {
compatible = "samsung,exynos5440-clock";
reg = <0x160000 0x1000>;
......@@ -79,8 +83,13 @@ cpufreq@160000 {
interrupts = <0 57 0>;
operating-points = <
/* KHz uV */
1500000 1100000
1400000 1075000
1300000 1050000
1200000 1025000
1100000 1000000
1000000 975000
900000 950000
800000 925000
>;
};
......@@ -101,14 +110,14 @@ serial@C0000 {
clock-names = "uart", "clk_uart_baud0";
};
spi {
compatible = "samsung,exynos4210-spi";
reg = <0xD0000 0x1000>;
spi_0: spi@D0000 {
compatible = "samsung,exynos5440-spi";
reg = <0xD0000 0x100>;
interrupts = <0 4 0>;
tx-dma-channel = <&pdma0 5>; /* preliminary */
rx-dma-channel = <&pdma0 4>; /* preliminary */
#address-cells = <1>;
#size-cells = <0>;
samsung,spi-src-clk = <0>;
num-cs = <1>;
clocks = <&clock 21>, <&clock 16>;
clock-names = "spi", "spi_busclk0";
};
......@@ -184,28 +193,6 @@ amba {
compatible = "arm,amba-bus";
interrupt-parent = <&gic>;
ranges;
pdma0: pdma@00121000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x121000 0x1000>;
interrupts = <0 46 0>;
clocks = <&clock 8>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
#dma-requests = <32>;
};
pdma1: pdma@00120000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x120000 0x1000>;
interrupts = <0 47 0>;
clocks = <&clock 8>;
clock-names = "apb_pclk";
#dma-cells = <1>;
#dma-channels = <8>;
#dma-requests = <32>;
};
};
rtc {
......@@ -214,6 +201,29 @@ rtc {
interrupts = <0 17 0>, <0 16 0>;
clocks = <&clock 21>;
clock-names = "rtc";
status = "disabled";
};
sata@210000 {
compatible = "snps,exynos5440-ahci";
reg = <0x210000 0x10000>;
interrupts = <0 30 0>;
clocks = <&clock 23>;
clock-names = "sata";
};
ohci@220000 {
compatible = "samsung,exynos5440-ohci";
reg = <0x220000 0x1000>;
interrupts = <0 29 0>;
clocks = <&clock 24>;
clock-names = "usbhost";
};
ehci@221000 {
compatible = "samsung,exynos5440-ehci";
reg = <0x221000 0x1000>;
interrupts = <0 29 0>;
clocks = <&clock 24>;
clock-names = "usbhost";
};
};
/*
* Samsung S3C2416 pinctrl settings
*
* Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
&pinctrl_0 {
/*
* Pin banks
*/
gpa: gpa {
gpio-controller;
#gpio-cells = <2>;
};
gpb: gpb {
gpio-controller;
#gpio-cells = <2>;
};
gpc: gpc {
gpio-controller;
#gpio-cells = <2>;
};
gpd: gpd {
gpio-controller;
#gpio-cells = <2>;
};
gpe: gpe {
gpio-controller;
#gpio-cells = <2>;
};
gpf: gpf {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpg: gpg {
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gph: gph {
gpio-controller;
#gpio-cells = <2>;
};
gpj: gpj {
gpio-controller;
#gpio-cells = <2>;
};
gpk: gpk {
gpio-controller;
#gpio-cells = <2>;
};
gpl: gpl {
gpio-controller;
#gpio-cells = <2>;
};
gpm: gpm {
gpio-controller;
#gpio-cells = <2>;
};
/*
* Pin groups
*/
uart0_data: uart0-data {
samsung,pins = "gph-0", "gph-1";
samsung,pin-function = <2>;
};
uart0_fctl: uart0-fctl {
samsung,pins = "gph-8", "gph-9";
samsung,pin-function = <2>;
};
uart1_data: uart1-data {
samsung,pins = "gph-2", "gph-3";
samsung,pin-function = <2>;
};
uart1_fctl: uart1-fctl {
samsung,pins = "gph-10", "gph-11";
samsung,pin-function = <2>;
};
uart2_data: uart2-data {
samsung,pins = "gph-4", "gph-5";
samsung,pin-function = <2>;
};
uart2_fctl: uart2-fctl {
samsung,pins = "gph-6", "gph-7";
samsung,pin-function = <2>;
};
uart3_data: uart3-data {
samsung,pins = "gph-6", "gph-7";
samsung,pin-function = <2>;
};
extuart_clk: extuart-clk {
samsung,pins = "gph-12";
samsung,pin-function = <2>;
};
i2c0_bus: i2c0-bus {
samsung,pins = "gpe-14", "gpe-15";
samsung,pin-function = <2>;
};
spi0_bus: spi0-bus {
samsung,pins = "gpe-11", "gpe-12", "gpe-13";
samsung,pin-function = <2>;
};
sd0_clk: sd0-clk {
samsung,pins = "gpe-5";
samsung,pin-function = <2>;
};
sd0_cmd: sd0-cmd {
samsung,pins = "gpe-6";
samsung,pin-function = <2>;
};
sd0_bus1: sd0-bus1 {
samsung,pins = "gpe-7";
samsung,pin-function = <2>;
};
sd0_bus4: sd0-bus4 {
samsung,pins = "gpe-8", "gpe-9", "gpe-10";
samsung,pin-function = <2>;
};
sd1_cmd: sd1-cmd {
samsung,pins = "gpl-8";
samsung,pin-function = <2>;
};
sd1_clk: sd1-clk {
samsung,pins = "gpl-9";
samsung,pin-function = <2>;
};
sd1_bus1: sd1-bus1 {
samsung,pins = "gpl-0";
samsung,pin-function = <2>;
};
sd1_bus4: sd1-bus4 {
samsung,pins = "gpl-1", "gpl-2", "gpl-3";
samsung,pin-function = <2>;
};
};
/*
* SAMSUNG SMDK2416 board device tree source
*
* Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/dts-v1/;
/include/ "s3c2416.dtsi"
/ {
model = "SMDK2416";
compatible = "samsung,s3c2416";
memory {
reg = <0x30000000 0x4000000>;
};
serial@50000000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart0_data>, <&uart0_fctl>;
};
serial@50004000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart1_data>, <&uart1_fctl>;
};
serial@50008000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart2_data>;
};
serial@5000C000 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&uart3_data>;
};
watchdog@53000000 {
status = "okay";
};
rtc@57000000 {
status = "okay";
};
sdhci@4AC00000 {
pinctrl-names = "default";
pinctrl-0 = <&sd0_clk>, <&sd0_cmd>,
<&sd0_bus1>, <&sd0_bus4>;
bus-width = <4>;
cd-gpios = <&gpf 1 0>;
cd-inverted;
status = "okay";
};
sdhci@4A800000 {
pinctrl-names = "default";
pinctrl-0 = <&sd1_clk>, <&sd1_cmd>,
<&sd1_bus1>, <&sd1_bus4>;
bus-width = <4>;
broken-cd;
status = "okay";
};
};
/*
* Samsung's S3C2416 SoC device tree source
*
* Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/include/ "s3c24xx.dtsi"
/include/ "s3c2416-pinctrl.dtsi"
/ {
model = "Samsung S3C2416 SoC";
compatible = "samsung,s3c2416";
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu {
compatible = "arm,arm926ejs";
};
};
interrupt-controller@4a000000 {
compatible = "samsung,s3c2416-irq";
};
pinctrl@56000000 {
compatible = "samsung,s3c2416-pinctrl";
};
serial@50000000 {
compatible = "samsung,s3c2440-uart";
};
serial@50004000 {
compatible = "samsung,s3c2440-uart";
};
serial@50008000 {
compatible = "samsung,s3c2440-uart";
};
serial@5000C000 {
compatible = "samsung,s3c2440-uart";
reg = <0x5000C000 0x4000>;
interrupts = <1 18 24 4>, <1 18 25 4>;
status = "disabled";
};
sdhci@4AC00000 {
compatible = "samsung,s3c6410-sdhci";
reg = <0x4AC00000 0x100>;
interrupts = <0 0 21 3>;
status = "disabled";
};
sdhci@4A800000 {
compatible = "samsung,s3c6410-sdhci";
reg = <0x4A800000 0x100>;
interrupts = <0 0 20 3>;
status = "disabled";
};
watchdog@53000000 {
interrupts = <1 9 27 3>;
};
rtc@57000000 {
compatible = "samsung,s3c2416-rtc";
};
i2c@54000000 {
compatible = "samsung,s3c2440-i2c";
};
};
/*
* Samsung's S3C24XX family device tree source
*
* Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/include/ "skeleton.dtsi"
/ {
compatible = "samsung,s3c24xx";
interrupt-parent = <&intc>;
aliases {
pinctrl0 = &pinctrl_0;
};
intc:interrupt-controller@4a000000 {
compatible = "samsung,s3c2410-irq";
reg = <0x4a000000 0x100>;
interrupt-controller;
#interrupt-cells = <4>;
};
pinctrl_0: pinctrl@56000000 {
reg = <0x56000000 0x1000>;
wakeup-interrupt-controller {
compatible = "samsung,s3c2410-wakeup-eint";
interrupts = <0 0 0 3>,
<0 0 1 3>,
<0 0 2 3>,
<0 0 3 3>,
<0 0 4 4>,
<0 0 5 4>;
};
};
timer@51000000 {
compatible = "samsung,s3c2410-pwm";
reg = <0x51000000 0x1000>;
interrupts = <0 0 10 3>, <0 0 11 3>, <0 0 12 3>, <0 0 13 3>, <0 0 14 3>;
#pwm-cells = <4>;
};
serial@50000000 {
compatible = "samsung,s3c2410-uart";
reg = <0x50000000 0x4000>;
interrupts = <1 28 0 4>, <1 28 1 4>;
status = "disabled";
};
serial@50004000 {
compatible = "samsung,s3c2410-uart";
reg = <0x50004000 0x4000>;
interrupts = <1 23 3 4>, <1 23 4 4>;
status = "disabled";
};
serial@50008000 {
compatible = "samsung,s3c2410-uart";
reg = <0x50008000 0x4000>;
interrupts = <1 15 6 4>, <1 15 7 4>;
status = "disabled";
};
watchdog@53000000 {
compatible = "samsung,s3c2410-wdt";
reg = <0x53000000 0x100>;
interrupts = <0 0 9 3>;
status = "disabled";
};
rtc@57000000 {
compatible = "samsung,s3c2410-rtc";
reg = <0x57000000 0x100>;
interrupts = <0 0 30 3>, <0 0 8 3>;
status = "disabled";
};
i2c@54000000 {
compatible = "samsung,s3c2410-i2c";
reg = <0x54000000 0x100>;
interrupts = <0 0 27 3>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
};
......@@ -486,6 +486,18 @@ config MACH_SMDK2416
help
Say Y here if you are using an SMDK2416
config MACH_S3C2416_DT
bool "Samsung S3C2416 machine using devicetree"
select CLKSRC_OF
select USE_OF
select PINCTRL
select PINCTRL_S3C24XX
help
Machine support for Samsung S3C2416 machines with device tree enabled.
Select this if a fdt blob is available for the S3C2416 SoC based board.
Note: This is under development and not all peripherals can be supported
with this machine file.
endif # CPU_S3C2416
if CPU_S3C2440
......
......@@ -79,6 +79,7 @@ obj-$(CONFIG_MACH_SMDK2413) += mach-smdk2413.o
obj-$(CONFIG_MACH_VSTMS) += mach-vstms.o
obj-$(CONFIG_MACH_SMDK2416) += mach-smdk2416.o
obj-$(CONFIG_MACH_S3C2416_DT) += mach-s3c2416-dt.o
obj-$(CONFIG_MACH_ANUBIS) += mach-anubis.o
obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
......
/*
* Samsung's S3C2416 flattened device tree enabled machine
*
* Copyright (c) 2012 Heiko Stuebner <heiko@sntech.de>
*
* based on mach-exynos/mach-exynos4-dt.c
*
* Copyright (c) 2010-2011 Samsung Electronics Co., Ltd.
* http://www.samsung.com
* Copyright (c) 2010-2011 Linaro Ltd.
* www.linaro.org
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/clocksource.h>
#include <linux/irqchip.h>
#include <linux/of_platform.h>
#include <linux/serial_core.h>
#include <asm/mach/arch.h>
#include <mach/map.h>
#include <plat/cpu.h>
#include <plat/pm.h>
#include <plat/regs-serial.h>
#include "common.h"
/*
* The following lookup table is used to override device names when devices
* are registered from device tree. This is temporarily added to enable
* device tree support addition for the S3C2416 architecture.
*
* For drivers that require platform data to be provided from the machine
* file, a platform data pointer can also be supplied along with the
* devices names. Usually, the platform data elements that cannot be parsed
* from the device tree by the drivers (example: function pointers) are
* supplied. But it should be noted that this is a temporary mechanism and
* at some point, the drivers should be capable of parsing all the platform
* data from the device tree.
*/
static const struct of_dev_auxdata s3c2416_auxdata_lookup[] __initconst = {
OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART,
"s3c2440-uart.0", NULL),
OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0x4000,
"s3c2440-uart.1", NULL),
OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0x8000,
"s3c2440-uart.2", NULL),
OF_DEV_AUXDATA("samsung,s3c2440-uart", S3C24XX_PA_UART + 0xC000,
"s3c2440-uart.3", NULL),
OF_DEV_AUXDATA("samsung,s3c6410-sdhci", S3C_PA_HSMMC0,
"s3c-sdhci.0", NULL),
OF_DEV_AUXDATA("samsung,s3c6410-sdhci", S3C_PA_HSMMC1,
"s3c-sdhci.1", NULL),
OF_DEV_AUXDATA("samsung,s3c2440-i2c", S3C_PA_IIC,
"s3c2440-i2c.0", NULL),
{},
};
static void __init s3c2416_dt_map_io(void)
{
s3c24xx_init_io(NULL, 0);
s3c24xx_init_clocks(12000000);
}
static void __init s3c2416_dt_machine_init(void)
{
of_platform_populate(NULL, of_default_bus_match_table,
s3c2416_auxdata_lookup, NULL);
s3c_pm_init();
}
static char const *s3c2416_dt_compat[] __initdata = {
"samsung,s3c2416",
"samsung,s3c2450",
NULL
};
DT_MACHINE_START(S3C2416_DT, "Samsung S3C2416 (Flattened Device Tree)")
/* Maintainer: Heiko Stuebner <heiko@sntech.de> */
.dt_compat = s3c2416_dt_compat,
.map_io = s3c2416_dt_map_io,
.init_irq = irqchip_init,
.init_machine = s3c2416_dt_machine_init,
.init_time = clocksource_of_init,
.restart = s3c2416_restart,
MACHINE_END
......@@ -151,7 +151,7 @@ enum exynos4_clks {
sclk_audio1, sclk_audio2, sclk_spdif, sclk_spi0, sclk_spi1, sclk_spi2,
sclk_slimbus, sclk_fimd1, sclk_mipi1, sclk_pcm1, sclk_pcm2, sclk_i2s1,
sclk_i2s2, sclk_mipihsi, sclk_mfc, sclk_pcm0, sclk_g3d, sclk_pwm_isp,
sclk_spi0_isp, sclk_spi1_isp, sclk_uart_isp,
sclk_spi0_isp, sclk_spi1_isp, sclk_uart_isp, sclk_fimg2d,
/* gate clocks */
fimc0 = 256, fimc1, fimc2, fimc3, csis0, csis1, jpeg, smmu_fimc0,
......@@ -484,6 +484,9 @@ struct samsung_mux_clock exynos4x12_mux_clks[] __initdata = {
MUX(none, "mout_spi0_isp", group1_p4x12, E4X12_SRC_ISP, 4, 4),
MUX(none, "mout_spi1_isp", group1_p4x12, E4X12_SRC_ISP, 8, 4),
MUX(none, "mout_uart_isp", group1_p4x12, E4X12_SRC_ISP, 12, 4),
MUX(none, "mout_g2d0", sclk_ampll_p4210, SRC_DMC, 20, 1),
MUX(none, "mout_g2d1", sclk_evpll_p, SRC_DMC, 24, 1),
MUX(none, "mout_g2d", mout_g2d_p, SRC_DMC, 28, 1),
};
/* list of divider clocks supported in all exynos4 soc's */
......@@ -552,7 +555,7 @@ struct samsung_div_clock exynos4_div_clks[] __initdata = {
/* list of divider clocks supported in exynos4210 soc */
struct samsung_div_clock exynos4210_div_clks[] __initdata = {
DIV(aclk200, "aclk200", "mout_aclk200", DIV_TOP, 0, 3),
DIV(none, "div_g2d", "mout_g2d", DIV_IMAGE, 0, 4),
DIV(sclk_fimg2d, "sclk_fimg2d", "mout_g2d", DIV_IMAGE, 0, 4),
DIV(none, "div_fimd1", "mout_fimd1", E4210_DIV_LCD1, 0, 4),
DIV(none, "div_mipi1", "mout_mipi1", E4210_DIV_LCD1, 16, 4),
DIV(none, "div_sata", "mout_sata", DIV_FSYS0, 20, 4),
......@@ -582,6 +585,7 @@ struct samsung_div_clock exynos4x12_div_clks[] __initdata = {
DIV(none, "div_mpwm", "div_isp1", E4X12_DIV_ISP1, 0, 3),
DIV(div_mcuisp0, "div_mcuisp0", "aclk400_mcuisp", E4X12_DIV_ISP1, 4, 3),
DIV(div_mcuisp1, "div_mcuisp1", "div_mcuisp0", E4X12_DIV_ISP1, 8, 3),
DIV(sclk_fimg2d, "sclk_fimg2d", "mout_g2d", DIV_DMC1, 0, 4),
};
/* list of gate clocks supported in all exynos4 soc's */
......@@ -909,6 +913,7 @@ struct samsung_gate_clock exynos4x12_gate_clks[] __initdata = {
CLK_IGNORE_UNUSED, 0),
GATE(spi1_isp, "spi1_isp", "aclk200", E4X12_GATE_ISP1, 13,
CLK_IGNORE_UNUSED, 0),
GATE(g2d, "g2d", "aclk200", GATE_IP_DMC, 23, 0, 0),
};
/*
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment