Commit f065a93e authored by Jan Beulich's avatar Jan Beulich Committed by Guenter Roeck

hwmon: (lm85) extend to support EMC6D103 chips

The interface is identical EMC6D102, so all that needs to be added are
some definitions and their uses.

Registers apparently missing in EMC6D103S/EMC6D103:A2 compared to EMC6D103:A0,
EMC6D103:A1, and EMC6D102 (according to the data sheets), but used
unconditionally in the driver: 62[5:7], 6D[0:7], and 6E[0:7]. For that
reason, EMC6D103S chips don't get enabled for the time being.
Signed-off-by: default avatarJan Beulich <jbeulich@novell.com>
(Guenter Roeck: Replaced EMC6D103_A2 with EMC6D103S per EMC6D103S datasheet)
Signed-off-by: default avatarGuenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@kernel.org
parent 4eb2abcd
......@@ -575,7 +575,7 @@ config SENSORS_LM85
help
If you say yes here you get support for National Semiconductor LM85
sensor chips and clones: ADM1027, ADT7463, ADT7468, EMC6D100,
EMC6D101 and EMC6D102.
EMC6D101, EMC6D102, and EMC6D103.
This driver can also be built as a module. If so, the module
will be called lm85.
......
......@@ -41,7 +41,7 @@ static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, I2C_CLIENT_END };
enum chips {
any_chip, lm85b, lm85c,
adm1027, adt7463, adt7468,
emc6d100, emc6d102
emc6d100, emc6d102, emc6d103
};
/* The LM85 registers */
......@@ -90,6 +90,9 @@ enum chips {
#define LM85_VERSTEP_EMC6D100_A0 0x60
#define LM85_VERSTEP_EMC6D100_A1 0x61
#define LM85_VERSTEP_EMC6D102 0x65
#define LM85_VERSTEP_EMC6D103_A0 0x68
#define LM85_VERSTEP_EMC6D103_A1 0x69
#define LM85_VERSTEP_EMC6D103S 0x6A /* Also known as EMC6D103:A2 */
#define LM85_REG_CONFIG 0x40
......@@ -348,6 +351,7 @@ static const struct i2c_device_id lm85_id[] = {
{ "emc6d100", emc6d100 },
{ "emc6d101", emc6d100 },
{ "emc6d102", emc6d102 },
{ "emc6d103", emc6d103 },
{ }
};
MODULE_DEVICE_TABLE(i2c, lm85_id);
......@@ -1250,6 +1254,20 @@ static int lm85_detect(struct i2c_client *client, struct i2c_board_info *info)
case LM85_VERSTEP_EMC6D102:
type_name = "emc6d102";
break;
case LM85_VERSTEP_EMC6D103_A0:
case LM85_VERSTEP_EMC6D103_A1:
type_name = "emc6d103";
break;
/*
* Registers apparently missing in EMC6D103S/EMC6D103:A2
* compared to EMC6D103:A0, EMC6D103:A1, and EMC6D102
* (according to the data sheets), but used unconditionally
* in the driver: 62[5:7], 6D[0:7], and 6E[0:7].
* So skip EMC6D103S for now.
case LM85_VERSTEP_EMC6D103S:
type_name = "emc6d103s";
break;
*/
}
} else {
dev_dbg(&adapter->dev,
......@@ -1283,6 +1301,7 @@ static int lm85_probe(struct i2c_client *client,
case adt7468:
case emc6d100:
case emc6d102:
case emc6d103:
data->freq_map = adm1027_freq_map;
break;
default:
......@@ -1468,7 +1487,7 @@ static struct lm85_data *lm85_update_device(struct device *dev)
/* More alarm bits */
data->alarms |= lm85_read_value(client,
EMC6D100_REG_ALARM3) << 16;
} else if (data->type == emc6d102) {
} else if (data->type == emc6d102 || data->type == emc6d103) {
/* Have to read LSB bits after the MSB ones because
the reading of the MSB bits has frozen the
LSBs (backward from the ADM1027).
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment