Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 "A new driver for FT5x06 based EDT displays and a couple of other
  driver changes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: synaptics - handle out of bounds values from the hardware
  Input: wacom - add support to Cintiq 22HD
  Input: add driver for FT5x06 based EDT displays

Documentation/input/edt-ft5x06.txt

+EDT ft5x06 based Polytouch devices
+----------------------------------
+
+The edt-ft5x06 driver is useful for the EDT "Polytouch" family of capacitive
+touch screens. Note that it is *not* suitable for other devices based on the
+focaltec ft5x06 devices, since they contain vendor-specific firmware. In
+particular this driver is not suitable for the Nook tablet.
+
+It has been tested with the following devices:
+  * EP0350M06
+  * EP0430M06
+  * EP0570M06
+  * EP0700M06
+
+The driver allows configuration of the touch screen via a set of sysfs files:
+
+/sys/class/input/eventX/device/device/threshold:
+    allows setting the "click"-threshold in the range from 20 to 80.
+
+/sys/class/input/eventX/device/device/gain:
+    allows setting the sensitivity in the range from 0 to 31. Note that
+    lower values indicate higher sensitivity.
+
+/sys/class/input/eventX/device/device/offset:
+    allows setting the edge compensation in the range from 0 to 31.
+
+/sys/class/input/eventX/device/device/report_rate:
+    allows setting the report rate in the range from 3 to 14.
+
+
+For debugging purposes the driver provides a few files in the debug
+filesystem (if available in the kernel). In /sys/kernel/debug/edt_ft5x06
+you'll find the following files:
+
+num_x, num_y:
+    (readonly) contains the number of sensor fields in X- and
+    Y-direction.
+
+mode:
+    allows switching the sensor between "factory mode" and "operation
+    mode" by writing "1" or "0" to it. In factory mode (1) it is
+    possible to get the raw data from the sensor. Note that in factory
+    mode regular events don't get delivered and the options described
+    above are unavailable.
+
+raw_data:
+    contains num_x * num_y big endian 16 bit values describing the raw
+    values for each sensor field. Note that each read() call on this
+    files triggers a new readout. It is recommended to provide a buffer
+    big enough to contain num_x * num_y * 2 bytes.
+
+Note that reading raw_data gives a I/O error when the device is not in factory
+mode. The same happens when reading/writing to the parameter files when the
+device is not in regular operation mode.

drivers/input/mouse/synaptics.c

@@ -40,11 +40,27 @@
  * Note that newer firmware allows querying device for maximum useable
  * coordinates.
  */
+#define XMIN 0
+#define XMAX 6143
+#define YMIN 0
+#define YMAX 6143
 #define XMIN_NOMINAL 1472
 #define XMAX_NOMINAL 5472
 #define YMIN_NOMINAL 1408
 #define YMAX_NOMINAL 4448
 
+/* Size in bits of absolute position values reported by the hardware */
+#define ABS_POS_BITS 13
+
+/*
+ * Any position values from the hardware above the following limits are
+ * treated as "wrapped around negative" values that have been truncated to
+ * the 13-bit reporting range of the hardware. These are just reasonable
+ * guesses and can be adjusted if hardware is found that operates outside
+ * of these parameters.
+ */
+#define X_MAX_POSITIVE (((1 << ABS_POS_BITS) + XMAX) / 2)
+#define Y_MAX_POSITIVE (((1 << ABS_POS_BITS) + YMAX) / 2)
 
 /*****************************************************************************
  *	Stuff we need even when we do not want native Synaptics support
@@ -588,6 +604,12 @@ static int synaptics_parse_hw_state(const unsigned char buf[],
 		hw->right = (buf[0] & 0x02) ? 1 : 0;
 	}
 
+	/* Convert wrap-around values to negative */
+	if (hw->x > X_MAX_POSITIVE)
+		hw->x -= 1 << ABS_POS_BITS;
+	if (hw->y > Y_MAX_POSITIVE)
+		hw->y -= 1 << ABS_POS_BITS;
+
 	return 0;
 }
 

drivers/input/tablet/wacom_wac.c

@@ -464,7 +464,7 @@ static void wacom_intuos_general(struct wacom_wac *wacom)
 		t = (data[6] << 2) | ((data[7] >> 6) & 3);
 		if ((features->type >= INTUOS4S && features->type <= INTUOS4L) ||
                     (features->type >= INTUOS5S && features->type <= INTUOS5L) ||
-		    features->type == WACOM_21UX2 || features->type == WACOM_24HD) {
+		    (features->type >= WACOM_21UX2 && features->type <= WACOM_24HD)) {
 			t = (t << 1) | (data[1] & 1);
 		}
 		input_report_abs(input, ABS_PRESSURE, t);
@@ -614,7 +614,7 @@ static int wacom_intuos_irq(struct wacom_wac *wacom)
 				input_report_abs(input, ABS_MISC, 0);
 			}
 		} else {
-			if (features->type == WACOM_21UX2) {
+			if (features->type == WACOM_21UX2 || features->type == WACOM_22HD) {
 				input_report_key(input, BTN_0, (data[5] & 0x01));
 				input_report_key(input, BTN_1, (data[6] & 0x01));
 				input_report_key(input, BTN_2, (data[6] & 0x02));
@@ -633,6 +633,12 @@ static int wacom_intuos_irq(struct wacom_wac *wacom)
 				input_report_key(input, BTN_Z, (data[8] & 0x20));
 				input_report_key(input, BTN_BASE, (data[8] & 0x40));
 				input_report_key(input, BTN_BASE2, (data[8] & 0x80));
+
+				if (features->type == WACOM_22HD) {
+					input_report_key(input, KEY_PROG1, data[9] & 0x01);
+					input_report_key(input, KEY_PROG2, data[9] & 0x02);
+					input_report_key(input, KEY_PROG3, data[9] & 0x04);
+				}
 			} else {
 				input_report_key(input, BTN_0, (data[5] & 0x01));
 				input_report_key(input, BTN_1, (data[5] & 0x02));
@@ -1231,6 +1237,7 @@ void wacom_wac_irq(struct wacom_wac *wacom_wac, size_t len)
 	case CINTIQ:
 	case WACOM_BEE:
 	case WACOM_21UX2:
+	case WACOM_22HD:
 	case WACOM_24HD:
 		sync = wacom_intuos_irq(wacom_wac);
 		break;
@@ -1432,6 +1439,12 @@ int wacom_setup_input_capabilities(struct input_dev *input_dev,
 		wacom_setup_cintiq(wacom_wac);
 		break;
 
+	case WACOM_22HD:
+		__set_bit(KEY_PROG1, input_dev->keybit);
+		__set_bit(KEY_PROG2, input_dev->keybit);
+		__set_bit(KEY_PROG3, input_dev->keybit);
+		/* fall through */
+
 	case WACOM_21UX2:
 		__set_bit(BTN_A, input_dev->keybit);
 		__set_bit(BTN_B, input_dev->keybit);
@@ -1858,6 +1871,9 @@ static const struct wacom_features wacom_features_0xF0 =
 static const struct wacom_features wacom_features_0xCC =
 	{ "Wacom Cintiq 21UX2",   WACOM_PKGLEN_INTUOS,    87200, 65600, 2047,
 	  63, WACOM_21UX2, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
+static const struct wacom_features wacom_features_0xFA =
+	{ "Wacom Cintiq 22HD",    WACOM_PKGLEN_INTUOS,    95840, 54260, 2047,
+	  63, WACOM_22HD, WACOM_INTUOS3_RES, WACOM_INTUOS3_RES };
 static const struct wacom_features wacom_features_0x90 =
 	{ "Wacom ISDv4 90",       WACOM_PKGLEN_GRAPHIRE,  26202, 16325,  255,
 	  0, TABLETPC, WACOM_INTUOS_RES, WACOM_INTUOS_RES };
@@ -2075,6 +2091,7 @@ const struct usb_device_id wacom_ids[] = {
 	{ USB_DEVICE_WACOM(0xEF) },
 	{ USB_DEVICE_WACOM(0x47) },
 	{ USB_DEVICE_WACOM(0xF4) },
+	{ USB_DEVICE_WACOM(0xFA) },
 	{ USB_DEVICE_LENOVO(0x6004) },
 	{ }
 };

drivers/input/tablet/wacom_wac.h

@@ -73,8 +73,9 @@ enum {
 	INTUOS5S,
 	INTUOS5,
 	INTUOS5L,
-	WACOM_24HD,
 	WACOM_21UX2,
+	WACOM_22HD,
+	WACOM_24HD,
 	CINTIQ,
 	WACOM_BEE,
 	WACOM_MO,

drivers/input/touchscreen/Kconfig

@@ -472,6 +472,19 @@ config TOUCHSCREEN_PENMOUNT
 	  To compile this driver as a module, choose M here: the
 	  module will be called penmount.
 
+config TOUCHSCREEN_EDT_FT5X06
+	tristate "EDT FocalTech FT5x06 I2C Touchscreen support"
+	depends on I2C
+	help
+	  Say Y here if you have an EDT "Polytouch" touchscreen based
+	  on the FocalTech FT5x06 family of controllers connected to
+	  your system.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called edt-ft5x06.
+
 config TOUCHSCREEN_MIGOR
 	tristate "Renesas MIGO-R touchscreen"
 	depends on SH_MIGOR && I2C

drivers/input/touchscreen/Makefile

@@ -24,6 +24,7 @@ obj-$(CONFIG_TOUCHSCREEN_CYTTSP_SPI)	+= cyttsp_spi.o
 obj-$(CONFIG_TOUCHSCREEN_DA9034)	+= da9034-ts.o
 obj-$(CONFIG_TOUCHSCREEN_DA9052)	+= da9052_tsi.o
 obj-$(CONFIG_TOUCHSCREEN_DYNAPRO)	+= dynapro.o
+obj-$(CONFIG_TOUCHSCREEN_EDT_FT5X06)	+= edt-ft5x06.o
 obj-$(CONFIG_TOUCHSCREEN_HAMPSHIRE)	+= hampshire.o
 obj-$(CONFIG_TOUCHSCREEN_GUNZE)		+= gunze.o
 obj-$(CONFIG_TOUCHSCREEN_EETI)		+= eeti_ts.o

include/linux/input/edt-ft5x06.h

+#ifndef _EDT_FT5X06_H
+#define _EDT_FT5X06_H
+
+/*
+ * Copyright (c) 2012 Simon Budig, <simon.budig@kernelconcepts.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+struct edt_ft5x06_platform_data {
+	int irq_pin;
+	int reset_pin;
+
+	/* startup defaults for operational parameters */
+	bool use_parameters;
+	u8 gain;
+	u8 threshold;
+	u8 offset;
+	u8 report_rate;
+};
+
+#endif /* _EDT_FT5X06_H */