Commit f21ccfa0 authored by Masanari Iida's avatar Masanari Iida Committed by Grant Likely

documentation/devicetree: Fix typos

Correct spelling typos within Documentation/devicetree
Signed-off-by: default avatarMasanari Iida <standby24x7@gmail.com>
Signed-off-by: default avatarGrant Likely <grant.likely@secretlab.ca>
parent c0a05bf0
......@@ -4,7 +4,7 @@ Required properties:
- compatible: Should be "atmel,<chip>-aic"
- interrupt-controller: Identifies the node as an interrupt controller.
- interrupt-parent: For single AIC system, it is an empty property.
- #interrupt-cells: The number of cells to define the interrupts. It sould be 3.
- #interrupt-cells: The number of cells to define the interrupts. It should be 3.
The first cell is the IRQ number (aka "Peripheral IDentifier" on datasheet).
The second cell is used to specify flags:
bits[3:0] trigger type and level flags:
......
......@@ -42,7 +42,7 @@ Main node required properties:
Optional
- interrupts : Interrupt source of the parent interrupt controller on
secondary GICs, or VGIC maintainance interrupt on primary GIC (see
secondary GICs, or VGIC maintenance interrupt on primary GIC (see
below).
- cpu-offset : per-cpu offset within the distributor and cpu interface
......@@ -74,7 +74,7 @@ Required properties:
virtual interface control register base and size. The 2nd additional
region is the GIC virtual cpu interface register base and size.
- interrupts : VGIC maintainance interrupt.
- interrupts : VGIC maintenance interrupt.
Example:
......
......@@ -39,16 +39,16 @@ Boards:
- OMAP3 Tobi with Overo : Commercial expansion board with daughter board
compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
- OMAP4 SDP : Software Developement Board
- OMAP4 SDP : Software Development Board
compatible = "ti,omap4-sdp", "ti,omap4430"
- OMAP4 PandaBoard : Low cost community board
compatible = "ti,omap4-panda", "ti,omap4430"
- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x
- OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x
compatible = "ti,omap3-evm", "ti,omap3"
- AM335X EVM : Software Developement Board for AM335x
- AM335X EVM : Software Development Board for AM335x
compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3"
- AM335X Bone : Low cost community board
......
* DMA Engine.
The Octeon DMA Engine transfers between the Boot Bus and main memory.
The DMA Engine will be refered to by phandle by any device that is
The DMA Engine will be referred to by phandle by any device that is
connected to it.
Properties:
......
......@@ -11,11 +11,11 @@ Required Properties:
* compatible: should be
- "samsung,exynos4210-dw-mshc": for controllers with Samsung Exynos4210
specific extentions.
specific extensions.
- "samsung,exynos4412-dw-mshc": for controllers with Samsung Exynos4412
specific extentions.
specific extensions.
- "samsung,exynos5250-dw-mshc": for controllers with Samsung Exynos5250
specific extentions.
specific extensions.
* samsung,dw-mshc-ciu-div: Specifies the divider value for the card interface
unit (ciu) clock. This property is applicable only for Exynos5 SoC's and
......
......@@ -55,5 +55,5 @@ Example:
};
Note: This example shows both SoC specific and board specific properties
in a single device node. The properties can be actually be seperated
in a single device node. The properties can be actually be separated
into SoC specific node and board specific node.
......@@ -8,9 +8,9 @@ Properties:
Definition: Must include "fsl,srio" for IP blocks with IP Block
Revision Register (SRIO IPBRR1) Major ID equal to 0x01c0.
Optionally, a compatiable string of "fsl,srio-vX.Y" where X is Major
Optionally, a compatible string of "fsl,srio-vX.Y" where X is Major
version in IP Block Revision Register and Y is Minor version. If this
compatiable is provided it should be ordered before "fsl,srio".
compatible is provided it should be ordered before "fsl,srio".
- reg
Usage: required
......
......@@ -17,9 +17,9 @@ Optional properties:
- ti,vsel1-gpio: Gpio for controlling VSEL1 line.
If this property is missing, then assume that there is no GPIO
for vsel1 control.
- ti,vsel0-state-high: Inital state of vsel0 input is high.
- ti,vsel0-state-high: Initial state of vsel0 input is high.
If this property is missing, then assume the state as low (0).
- ti,vsel1-state-high: Inital state of vsel1 input is high.
- ti,vsel1-state-high: Initial state of vsel1 input is high.
If this property is missing, then assume the state as low (0).
Any property defined as part of the core regulator binding, defined in
......
......@@ -7,7 +7,7 @@ Required properties:
- reg: physical base address of the controller and length of memory mapped
region.
- interrupts: Two interrupt numbers to the cpu should be specified. First
interrupt number is the rtc alarm interupt and second interrupt number
interrupt number is the rtc alarm interrupt and second interrupt number
is the rtc tick interrupt. The number of cells representing a interrupt
depends on the parent interrupt controller.
......
......@@ -2,7 +2,7 @@
The Samsung's Watchdog controller is used for resuming system operation
after a preset amount of time during which the WDT reset event has not
occured.
occurred.
Required properties:
- compatible : should be "samsung,s3c2410-wdt"
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment