Merge branch 'topic/cppi' into for-linus

Documentation/devicetree/bindings/usb/da8xx-usb.txt

@@ -18,10 +18,26 @@ Required properties:
 
  - phy-names: Should be "usb-phy"
 
+ - dmas: specifies the dma channels
+
+ - dma-names: specifies the names of the channels. Use "rxN" for receive
+   and "txN" for transmit endpoints. N specifies the endpoint number.
+
 Optional properties:
 ~~~~~~~~~~~~~~~~~~~~
  - vbus-supply: Phandle to a regulator providing the USB bus power.
 
+DMA
+~~~
+- compatible: ti,da830-cppi41
+- reg: offset and length of the following register spaces: CPPI DMA Controller,
+  CPPI DMA Scheduler, Queue Manager
+- reg-names: "controller", "scheduler", "queuemgr"
+- #dma-cells: should be set to 2. The first number represents the
+  channel number (0 … 3 for endpoints 1 … 4).
+  The second number is 0 for RX and 1 for TX transfers.
+- #dma-channels: should be set to 4 representing the 4 endpoints.
+
 Example:
 	usb_phy: usb-phy {
 		compatible = "ti,da830-usb-phy";
@@ -30,7 +46,10 @@ Example:
 	};
 	usb0: usb@200000 {
 		compatible = "ti,da830-musb";
-		reg =   <0x00200000 0x10000>;
+		reg = <0x00200000 0x1000>;
+		ranges;
+		#address-cells = <1>;
+		#size-cells = <1>;
 		interrupts = <58>;
 		interrupt-names = "mc";
 
@@ -39,5 +58,25 @@ Example:
 		phys = <&usb_phy 0>;
 		phy-names = "usb-phy";
 
+		dmas = <&cppi41dma 0 0 &cppi41dma 1 0
+			&cppi41dma 2 0 &cppi41dma 3 0
+			&cppi41dma 0 1 &cppi41dma 1 1
+			&cppi41dma 2 1 &cppi41dma 3 1>;
+		dma-names =
+			"rx1", "rx2", "rx3", "rx4",
+			"tx1", "tx2", "tx3", "tx4";
+
 		status = "okay";
+
+		cppi41dma: dma-controller@201000 {
+			compatible = "ti,da830-cppi41";
+			reg =  <0x201000 0x1000
+				0x202000 0x1000
+				0x204000 0x4000>;
+			reg-names = "controller", "scheduler", "queuemgr";
+			interrupts = <58>;
+			#dma-cells = <2>;
+			#dma-channels = <4>;
+		};
+
 	};

drivers/dma/Kconfig

@@ -514,12 +514,12 @@ config TIMB_DMA
 	  Enable support for the Timberdale FPGA DMA engine.
 
 config TI_CPPI41
-	tristate "AM33xx CPPI41 DMA support"
-	depends on ARCH_OMAP
+	tristate "CPPI 4.1 DMA support"
+	depends on (ARCH_OMAP || ARCH_DAVINCI_DA8XX)
 	select DMA_ENGINE
 	help
 	  The Communications Port Programming Interface (CPPI) 4.1 DMA engine
-	  is currently used by the USB driver on AM335x platforms.
+	  is currently used by the USB driver on AM335x and DA8xx platforms.
 
 config TI_DMA_CROSSBAR
 	bool