Commit f2402f21 authored by Hauke Mehrtens's avatar Hauke Mehrtens Committed by Greg Kroah-Hartman

USB: Add USB 2.0 to ssb ohci driver

This adds USB 2.0 support to ssb ohci driver.
This patch was used in OpenWRT for a long time now.

CC: Steve Brown <sbrown@cortland.com>
Signed-off-by: default avatarHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 356c5a48
......@@ -93,8 +93,11 @@ static void ssb_ohci_detach(struct ssb_device *dev)
{
struct usb_hcd *hcd = ssb_get_drvdata(dev);
if (hcd->driver->shutdown)
hcd->driver->shutdown(hcd);
usb_remove_hcd(hcd);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
ssb_device_disable(dev, 0);
}
......@@ -106,10 +109,52 @@ static int ssb_ohci_attach(struct ssb_device *dev)
int err = -ENOMEM;
u32 tmp, flags = 0;
if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
flags |= SSB_OHCI_TMSLOW_HOSTMODE;
if (dma_set_mask(dev->dma_dev, DMA_BIT_MASK(32)) ||
dma_set_coherent_mask(dev->dma_dev, DMA_BIT_MASK(32)))
return -EOPNOTSUPP;
ssb_device_enable(dev, flags);
if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
/* Put the device into host-mode. */
flags |= SSB_OHCI_TMSLOW_HOSTMODE;
ssb_device_enable(dev, flags);
} else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
/*
* USB 2.0 special considerations:
*
* In addition to the standard SSB reset sequence, the Host
* Control Register must be programmed to bring the USB core
* and various phy components out of reset.
*/
ssb_device_enable(dev, 0);
ssb_write32(dev, 0x200, 0x7ff);
/* Change Flush control reg */
tmp = ssb_read32(dev, 0x400);
tmp &= ~8;
ssb_write32(dev, 0x400, tmp);
tmp = ssb_read32(dev, 0x400);
/* Change Shim control reg */
tmp = ssb_read32(dev, 0x304);
tmp &= ~0x100;
ssb_write32(dev, 0x304, tmp);
tmp = ssb_read32(dev, 0x304);
udelay(1);
/* Work around for 5354 failures */
if (dev->id.revision == 2 && dev->bus->chip_id == 0x5354) {
/* Change syn01 reg */
tmp = 0x00fe00fe;
ssb_write32(dev, 0x894, tmp);
/* Change syn03 reg */
tmp = ssb_read32(dev, 0x89c);
tmp |= 0x1;
ssb_write32(dev, 0x89c, tmp);
}
} else
ssb_device_enable(dev, 0);
hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
dev_name(dev->dev));
......@@ -200,6 +245,7 @@ static int ssb_ohci_resume(struct ssb_device *dev)
static const struct ssb_device_id ssb_ohci_table[] = {
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
SSB_DEVTABLE_END
};
MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment