arm: vf610: zii devel b: Add support for switch interrupts

The Switches use GPIO lines to indicate interrupts from two of the
switches.

With these interrupts in place, we can make use of the interrupt
controllers within the switch to indicate when the internal PHYs
generate an interrupt. Use standard PHY properties to do this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

arch/arm/boot/dts/vf610-zii-dev-rev-b.dts

@@ -88,10 +88,16 @@ mdio_mux_1: mdio@1 {
 
 			switch0: switch0@0 {
 				compatible = "marvell,mv88e6085";
+				pinctrl-0 = <&pinctrl_gpio_switch0>;
+				pinctrl-names = "default";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0>;
 				dsa,member = <0 0>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 
 				ports {
 					#address-cells = <1>;
@@ -99,16 +105,19 @@ ports {
 					port@0 {
 						reg = <0>;
 						label = "lan0";
+						phy-handle = <&switch0phy0>;
 					};
 
 					port@1 {
 						reg = <1>;
 						label = "lan1";
+						phy-handle = <&switch0phy1>;
 					};
 
 					port@2 {
 						reg = <2>;
 						label = "lan2";
+						phy-handle = <&switch0phy2>;
 					};
 
 					switch0port5: port@5 {
@@ -133,6 +142,24 @@ fixed-link {
 						};
 					};
 				};
+				mdio {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					switch0phy0: switch0phy0@0 {
+						reg = <0>;
+						interrupt-parent = <&switch0>;
+						interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+					};
+					switch0phy1: switch1phy0@1 {
+						reg = <1>;
+						interrupt-parent = <&switch0>;
+						interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;					};
+					switch0phy2: switch1phy0@2 {
+						reg = <2>;
+						interrupt-parent = <&switch0>;
+						interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+					};
+				};
 			};
 		};
 
@@ -143,10 +170,16 @@ mdio_mux_2: mdio@2 {
 
 			switch1: switch1@0 {
 				compatible = "marvell,mv88e6085";
+				pinctrl-0 = <&pinctrl_gpio_switch1>;
+				pinctrl-names = "default";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0>;
 				dsa,member = <0 1>;
+				interrupt-parent = <&gpio0>;
+				interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
 
 				ports {
 					#address-cells = <1>;
@@ -196,12 +229,18 @@ mdio {
 					#size-cells = <0>;
 					switch1phy0: switch1phy0@0 {
 						reg = <0>;
+						interrupt-parent = <&switch1>;
+						interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
 					};
 					switch1phy1: switch1phy0@1 {
 						reg = <1>;
+						interrupt-parent = <&switch1>;
+						interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 					};
 					switch1phy2: switch1phy0@2 {
 						reg = <2>;
+						interrupt-parent = <&switch1>;
+						interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 					};
 				};
 			};
@@ -636,6 +675,18 @@ VF610_PAD_PTB18__GPIO_40	0x33e2
 		>;
 	};
 
+	pinctrl_gpio_switch0: pinctrl-gpio-switch0 {
+		fsl,pins = <
+			VF610_PAD_PTB5__GPIO_27		0x219d
+		>;
+	};
+
+	pinctrl_gpio_switch1: pinctrl-gpio-switch1 {
+		fsl,pins = <
+			VF610_PAD_PTB4__GPIO_26		0x219d
+		>;
+	};
+
 	pinctrl_i2c_mux_reset: pinctrl-i2c-mux-reset {
 		fsl,pins = <
 			 VF610_PAD_PTE14__GPIO_119	0x31c2