Commit f30a19b8 authored by Rasmus Villemoes's avatar Rasmus Villemoes Committed by David S. Miller

net: dsa: mv88e6xxx: introduce support for two chips using direct smi addressing

The 88e6250 (as well as 6220, 6071, 6070, 6020) do not support
multi-chip (indirect) addressing. However, one can still have two of
them on the same mdio bus, since the device only uses 16 of the 32
possible addresses, either addresses 0x00-0x0F or 0x10-0x1F depending
on the ADDR4 pin at reset [since ADDR4 is internally pulled high, the
latter is the default].

In order to prepare for supporting the 88e6250 and friends, introduce
mv88e6xxx_info::dual_chip to allow having a non-zero sw_addr while
still using direct addressing.
Reviewed-by: default avatarVivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarRasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent df63b0d9
...@@ -112,6 +112,12 @@ struct mv88e6xxx_info { ...@@ -112,6 +112,12 @@ struct mv88e6xxx_info {
* when it is non-zero, and use indirect access to internal registers. * when it is non-zero, and use indirect access to internal registers.
*/ */
bool multi_chip; bool multi_chip;
/* Dual-chip Addressing Mode
* Some chips respond to only half of the 32 SMI addresses,
* allowing two to coexist on the same SMI interface.
*/
bool dual_chip;
enum dsa_tag_protocol tag_protocol; enum dsa_tag_protocol tag_protocol;
/* Mask for FromPort and ToPort value of PortVec used in ATU Move /* Mask for FromPort and ToPort value of PortVec used in ATU Move
......
...@@ -24,6 +24,10 @@ ...@@ -24,6 +24,10 @@
* When ADDR is non-zero, the chip uses Multi-chip Addressing Mode, allowing * When ADDR is non-zero, the chip uses Multi-chip Addressing Mode, allowing
* multiple devices to share the SMI interface. In this mode it responds to only * multiple devices to share the SMI interface. In this mode it responds to only
* 2 registers, used to indirectly access the internal SMI devices. * 2 registers, used to indirectly access the internal SMI devices.
*
* Some chips use a different scheme: Only the ADDR4 pin is used for
* configuration, and the device responds to 16 of the 32 SMI
* addresses, allowing two to coexist on the same SMI interface.
*/ */
static int mv88e6xxx_smi_direct_read(struct mv88e6xxx_chip *chip, static int mv88e6xxx_smi_direct_read(struct mv88e6xxx_chip *chip,
...@@ -76,6 +80,23 @@ static const struct mv88e6xxx_bus_ops mv88e6xxx_smi_direct_ops = { ...@@ -76,6 +80,23 @@ static const struct mv88e6xxx_bus_ops mv88e6xxx_smi_direct_ops = {
.write = mv88e6xxx_smi_direct_write, .write = mv88e6xxx_smi_direct_write,
}; };
static int mv88e6xxx_smi_dual_direct_read(struct mv88e6xxx_chip *chip,
int dev, int reg, u16 *data)
{
return mv88e6xxx_smi_direct_read(chip, chip->sw_addr + dev, reg, data);
}
static int mv88e6xxx_smi_dual_direct_write(struct mv88e6xxx_chip *chip,
int dev, int reg, u16 data)
{
return mv88e6xxx_smi_direct_write(chip, chip->sw_addr + dev, reg, data);
}
static const struct mv88e6xxx_bus_ops mv88e6xxx_smi_dual_direct_ops = {
.read = mv88e6xxx_smi_dual_direct_read,
.write = mv88e6xxx_smi_dual_direct_write,
};
/* Offset 0x00: SMI Command Register /* Offset 0x00: SMI Command Register
* Offset 0x01: SMI Data Register * Offset 0x01: SMI Data Register
*/ */
...@@ -144,7 +165,9 @@ static const struct mv88e6xxx_bus_ops mv88e6xxx_smi_indirect_ops = { ...@@ -144,7 +165,9 @@ static const struct mv88e6xxx_bus_ops mv88e6xxx_smi_indirect_ops = {
int mv88e6xxx_smi_init(struct mv88e6xxx_chip *chip, int mv88e6xxx_smi_init(struct mv88e6xxx_chip *chip,
struct mii_bus *bus, int sw_addr) struct mii_bus *bus, int sw_addr)
{ {
if (sw_addr == 0) if (chip->info->dual_chip)
chip->smi_ops = &mv88e6xxx_smi_dual_direct_ops;
else if (sw_addr == 0)
chip->smi_ops = &mv88e6xxx_smi_direct_ops; chip->smi_ops = &mv88e6xxx_smi_direct_ops;
else if (chip->info->multi_chip) else if (chip->info->multi_chip)
chip->smi_ops = &mv88e6xxx_smi_indirect_ops; chip->smi_ops = &mv88e6xxx_smi_indirect_ops;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment