Merge branch 'smsc-energy-detect'

Heiko Schocher says:

====================
net, phy, smsc: add posibility to disable energy detect mode

On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Therefore the property "smsc,disable-energy-detect" is
introduced.

Patch 1 introduces phy-handle support for the ti,cpsw
driver. This is needed now for the smsc phy.

Patch 2 adds the disable energy mode functionality
to the smsc phy

Changes in v2:
- add comments from Florian Fainelli
  - I did not change disable property name into enable
    because I fear to break existing behaviour
  - add smsc vendor prefix
  - remove CONFIG_OF and use __maybe_unused
  - introduce "phy-handle" ability into ti,cpsw
    driver, so I can remove bogus:
      if (!of_node && dev->parent->of_node)
          of_node = dev->parent->of_node;
    construct. Therefore new patch for the ti,cpsw
    driver is necessary.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/cpsw.txt

@@ -39,6 +39,7 @@ Required properties:
 Optional properties:
 - dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
 - mac-address		: See ethernet.txt file in the same directory
+- phy-handle		: See ethernet.txt file in the same directory
 
 Note: "ti,hwmods" field is used to fetch the base address and irq
 resources from TI, omap hwmod data base during device registration.

Documentation/devicetree/bindings/net/smsc-lan87xx.txt

+SMSC LAN87xx Ethernet PHY
+
+Some boards require special tuning values. Configure them
+through an Ethernet OF device node.
+
+Optional properties:
+
+- smsc,disable-energy-detect:
+  If set, do not enable energy detect mode for the SMSC phy.
+  default: enable energy detect mode
+
+Examples:
+smsc phy with disabled energy detect mode on an am335x based board.
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&davinci_mdio_default>;
+	pinctrl-1 = <&davinci_mdio_sleep>;
+	status = "okay";
+
+	ethernetphy0: ethernet-phy@0 {
+		reg = <0>;
+		smsc,disable-energy-detect;
+	};
+};

drivers/net/ethernet/ti/cpsw.c

@@ -30,6 +30,7 @@
 #include <linux/delay.h>
 #include <linux/pm_runtime.h>
 #include <linux/of.h>
+#include <linux/of_mdio.h>
 #include <linux/of_net.h>
 #include <linux/of_device.h>
 #include <linux/if_vlan.h>
@@ -365,6 +366,7 @@ struct cpsw_priv {
 	spinlock_t			lock;
 	struct platform_device		*pdev;
 	struct net_device		*ndev;
+	struct device_node		*phy_node;
 	struct napi_struct		napi_rx;
 	struct napi_struct		napi_tx;
 	struct device			*dev;
@@ -1145,7 +1147,11 @@ static void cpsw_slave_open(struct cpsw_slave *slave, struct cpsw_priv *priv)
 		cpsw_ale_add_mcast(priv->ale, priv->ndev->broadcast,
 				   1 << slave_port, 0, 0, ALE_MCAST_FWD_2);
 
-	slave->phy = phy_connect(priv->ndev, slave->data->phy_id,
+	if (priv->phy_node)
+		slave->phy = of_phy_connect(priv->ndev, priv->phy_node,
+				 &cpsw_adjust_link, 0, slave->data->phy_if);
+	else
+		slave->phy = phy_connect(priv->ndev, slave->data->phy_id,
 				 &cpsw_adjust_link, slave->data->phy_if);
 	if (IS_ERR(slave->phy)) {
 		dev_err(priv->dev, "phy %s not found on slave %d\n",
@@ -1934,11 +1940,12 @@ static void cpsw_slave_init(struct cpsw_slave *slave, struct cpsw_priv *priv,
 	slave->port_vlan = data->dual_emac_res_vlan;
 }
 
-static int cpsw_probe_dt(struct cpsw_platform_data *data,
+static int cpsw_probe_dt(struct cpsw_priv *priv,
 			 struct platform_device *pdev)
 {
 	struct device_node *node = pdev->dev.of_node;
 	struct device_node *slave_node;
+	struct cpsw_platform_data *data = &priv->data;
 	int i = 0, ret;
 	u32 prop;
 
@@ -2029,6 +2036,7 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
 		if (strcmp(slave_node->name, "slave"))
 			continue;
 
+		priv->phy_node = of_parse_phandle(slave_node, "phy-handle", 0);
 		parp = of_get_property(slave_node, "phy_id", &lenp);
 		if ((parp == NULL) || (lenp != (sizeof(void *) * 2))) {
 			dev_err(&pdev->dev, "Missing slave[%d] phy_id property\n", i);
@@ -2044,7 +2052,6 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data,
 		}
 		snprintf(slave_data->phy_id, sizeof(slave_data->phy_id),
 			 PHY_ID_FMT, mdio->name, phyid);
-
 		slave_data->phy_if = of_get_phy_mode(slave_node);
 		if (slave_data->phy_if < 0) {
 			dev_err(&pdev->dev, "Missing or malformed slave[%d] phy-mode property\n",
@@ -2240,7 +2247,7 @@ static int cpsw_probe(struct platform_device *pdev)
 	/* Select default pin state */
 	pinctrl_pm_select_default_state(&pdev->dev);
 
-	if (cpsw_probe_dt(&priv->data, pdev)) {
+	if (cpsw_probe_dt(priv, pdev)) {
 		dev_err(&pdev->dev, "cpsw: platform data missing\n");
 		ret = -ENODEV;
 		goto clean_runtime_disable_ret;

drivers/net/phy/smsc.c

@@ -43,16 +43,25 @@ static int smsc_phy_ack_interrupt(struct phy_device *phydev)
 
 static int smsc_phy_config_init(struct phy_device *phydev)
 {
+	int __maybe_unused len;
+	struct device *dev __maybe_unused = &phydev->dev;
+	struct device_node *of_node __maybe_unused = dev->of_node;
 	int rc = phy_read(phydev, MII_LAN83C185_CTRL_STATUS);
+	int enable_energy = 1;
 
 	if (rc < 0)
 		return rc;
 
-	/* Enable energy detect mode for this SMSC Transceivers */
-	rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS,
-		       rc | MII_LAN83C185_EDPWRDOWN);
-	if (rc < 0)
-		return rc;
+	if (of_find_property(of_node, "smsc,disable-energy-detect", &len))
+		enable_energy = 0;
+
+	if (enable_energy) {
+		/* Enable energy detect mode for this SMSC Transceivers */
+		rc = phy_write(phydev, MII_LAN83C185_CTRL_STATUS,
+			       rc | MII_LAN83C185_EDPWRDOWN);
+		if (rc < 0)
+			return rc;
+	}
 
 	return smsc_phy_ack_interrupt(phydev);
 }