Merge remote-tracking branches 'asoc/topic/wm8804', 'asoc/topic/wm8904',...

Merge remote-tracking branches 'asoc/topic/wm8804', 'asoc/topic/wm8904', 'asoc/topic/wm8960', 'asoc/topic/wm8988' and 'asoc/topic/xtfpga' into asoc-next

Documentation/devicetree/bindings/sound/cdns,xtfpga-i2s.txt

+Bindings for I2S controller built into xtfpga Xtensa bitstreams.
+
+Required properties:
+- compatible: shall be "cdns,xtfpga-i2s".
+- reg: memory region (address and length) with device registers.
+- interrupts: interrupt for the device.
+- clocks: phandle to the clk used as master clock. I2S bus clock
+  is derived from it.
+
+Examples:
+
+	i2s0: xtfpga-i2s@0d080000 {
+		#sound-dai-cells = <0>;
+		compatible = "cdns,xtfpga-i2s";
+		reg = <0x0d080000 0x40>;
+		interrupts = <2 1>;
+		clocks = <&cdce706 4>;
+	};

Documentation/devicetree/bindings/sound/wm8904.txt

@@ -3,7 +3,7 @@ WM8904 audio CODEC
 This device supports I2C only.
 
 Required properties:
-  - compatible: "wlf,wm8904"
+  - compatible: "wlf,wm8904" or "wlf,wm8912"
   - reg: the I2C address of the device.
   - clock-names: "mclk"
   - clocks: reference to

MAINTAINERS

@@ -10669,6 +10669,7 @@ M:	Max Filippov <jcmvbkbc@gmail.com>
 L:	linux-xtensa@linux-xtensa.org
 S:	Maintained
 F:	drivers/spi/spi-xtensa-xtfpga.c
+F:	sound/soc/xtensa/xtfpga-i2s.c
 
 YAM DRIVER FOR AX.25
 M:	Jean-Paul Roubelat <jpr@f6fbb.org>

sound/soc/Kconfig

@@ -55,6 +55,7 @@ source "sound/soc/spear/Kconfig"
 source "sound/soc/tegra/Kconfig"
 source "sound/soc/txx9/Kconfig"
 source "sound/soc/ux500/Kconfig"
+source "sound/soc/xtensa/Kconfig"
 
 # Supported codecs
 source "sound/soc/codecs/Kconfig"

sound/soc/Makefile

@@ -36,3 +36,4 @@ obj-$(CONFIG_SND_SOC)	+= spear/
 obj-$(CONFIG_SND_SOC)	+= tegra/
 obj-$(CONFIG_SND_SOC)	+= txx9/
 obj-$(CONFIG_SND_SOC)	+= ux500/
+obj-$(CONFIG_SND_SOC)	+= xtensa/

sound/soc/codecs/wm8804.c

@@ -648,7 +648,7 @@ static struct snd_soc_dai_driver wm8804_dai = {
 	.symmetric_rates = 1
 };
 
-static struct snd_soc_codec_driver soc_codec_dev_wm8804 = {
+static const struct snd_soc_codec_driver soc_codec_dev_wm8804 = {
 	.probe = wm8804_probe,
 	.remove = wm8804_remove,
 	.set_bias_level = wm8804_set_bias_level,
@@ -664,7 +664,7 @@ static const struct of_device_id wm8804_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, wm8804_of_match);
 
-static struct regmap_config wm8804_regmap_config = {
+static const struct regmap_config wm8804_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
 

sound/soc/codecs/wm8904.c

@@ -2105,6 +2105,24 @@ static const struct regmap_config wm8904_regmap = {
 	.num_reg_defaults = ARRAY_SIZE(wm8904_reg_defaults),
 };
 
+#ifdef CONFIG_OF
+static enum wm8904_type wm8904_data = WM8904;
+static enum wm8904_type wm8912_data = WM8912;
+
+static const struct of_device_id wm8904_of_match[] = {
+	{
+		.compatible = "wlf,wm8904",
+		.data = &wm8904_data,
+	}, {
+		.compatible = "wlf,wm8912",
+		.data = &wm8912_data,
+	}, {
+		/* sentinel */
+	}
+};
+MODULE_DEVICE_TABLE(of, wm8904_of_match);
+#endif
+
 static int wm8904_i2c_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {
@@ -2132,7 +2150,17 @@ static int wm8904_i2c_probe(struct i2c_client *i2c,
 		return ret;
 	}
 
-	wm8904->devtype = id->driver_data;
+	if (i2c->dev.of_node) {
+		const struct of_device_id *match;
+
+		match = of_match_node(wm8904_of_match, i2c->dev.of_node);
+		if (match == NULL)
+			return -EINVAL;
+		wm8904->devtype = *((enum wm8904_type *)match->data);
+	} else {
+		wm8904->devtype = id->driver_data;
+	}
+
 	i2c_set_clientdata(i2c, wm8904);
 	wm8904->pdata = i2c->dev.platform_data;
 
@@ -2266,6 +2294,7 @@ static struct i2c_driver wm8904_i2c_driver = {
 	.driver = {
 		.name = "wm8904",
 		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(wm8904_of_match),
 	},
 	.probe =    wm8904_i2c_probe,
 	.remove =   wm8904_i2c_remove,

sound/soc/codecs/wm8960.c

@@ -15,6 +15,7 @@
 #include <linux/init.h>
 #include <linux/delay.h>
 #include <linux/pm.h>
+#include <linux/clk.h>
 #include <linux/i2c.h>
 #include <linux/slab.h>
 #include <sound/core.h>
@@ -117,6 +118,7 @@ static bool wm8960_volatile(struct device *dev, unsigned int reg)
 }
 
 struct wm8960_priv {
+	struct clk *mclk;
 	struct regmap *regmap;
 	int (*set_bias_level)(struct snd_soc_codec *,
 			      enum snd_soc_bias_level level);
@@ -618,14 +620,38 @@ static int wm8960_set_bias_level_out3(struct snd_soc_codec *codec,
 				      enum snd_soc_bias_level level)
 {
 	struct wm8960_priv *wm8960 = snd_soc_codec_get_drvdata(codec);
+	int ret;
 
 	switch (level) {
 	case SND_SOC_BIAS_ON:
 		break;
 
 	case SND_SOC_BIAS_PREPARE:
-		/* Set VMID to 2x50k */
-		snd_soc_update_bits(codec, WM8960_POWER1, 0x180, 0x80);
+		switch (codec->dapm.bias_level) {
+		case SND_SOC_BIAS_STANDBY:
+			if (!IS_ERR(wm8960->mclk)) {
+				ret = clk_prepare_enable(wm8960->mclk);
+				if (ret) {
+					dev_err(codec->dev,
+						"Failed to enable MCLK: %d\n",
+						ret);
+					return ret;
+				}
+			}
+
+			/* Set VMID to 2x50k */
+			snd_soc_update_bits(codec, WM8960_POWER1, 0x180, 0x80);
+			break;
+
+		case SND_SOC_BIAS_ON:
+			if (!IS_ERR(wm8960->mclk))
+				clk_disable_unprepare(wm8960->mclk);
+			break;
+
+		default:
+			break;
+		}
+
 		break;
 
 	case SND_SOC_BIAS_STANDBY:
@@ -674,7 +700,7 @@ static int wm8960_set_bias_level_capless(struct snd_soc_codec *codec,
 					 enum snd_soc_bias_level level)
 {
 	struct wm8960_priv *wm8960 = snd_soc_codec_get_drvdata(codec);
-	int reg;
+	int reg, ret;
 
 	switch (level) {
 	case SND_SOC_BIAS_ON:
@@ -715,9 +741,22 @@ static int wm8960_set_bias_level_capless(struct snd_soc_codec *codec,
 					    WM8960_VREF, WM8960_VREF);
 
 			msleep(100);
+
+			if (!IS_ERR(wm8960->mclk)) {
+				ret = clk_prepare_enable(wm8960->mclk);
+				if (ret) {
+					dev_err(codec->dev,
+						"Failed to enable MCLK: %d\n",
+						ret);
+					return ret;
+				}
+			}
 			break;
 
 		case SND_SOC_BIAS_ON:
+			if (!IS_ERR(wm8960->mclk))
+				clk_disable_unprepare(wm8960->mclk);
+
 			/* Enable anti-pop mode */
 			snd_soc_update_bits(codec, WM8960_APOP1,
 					    WM8960_POBCTRL | WM8960_SOFT_ST |
@@ -1002,6 +1041,12 @@ static int wm8960_i2c_probe(struct i2c_client *i2c,
 	if (wm8960 == NULL)
 		return -ENOMEM;
 
+	wm8960->mclk = devm_clk_get(&i2c->dev, "mclk");
+	if (IS_ERR(wm8960->mclk)) {
+		if (PTR_ERR(wm8960->mclk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+	}
+
 	wm8960->regmap = devm_regmap_init_i2c(i2c, &wm8960_regmap);
 	if (IS_ERR(wm8960->regmap))
 		return PTR_ERR(wm8960->regmap);

sound/soc/codecs/wm8988.c

@@ -813,7 +813,7 @@ static int wm8988_probe(struct snd_soc_codec *codec)
 	return 0;
 }
 
-static struct snd_soc_codec_driver soc_codec_dev_wm8988 = {
+static const struct snd_soc_codec_driver soc_codec_dev_wm8988 = {
 	.probe =	wm8988_probe,
 	.set_bias_level = wm8988_set_bias_level,
 	.suspend_bias_off = true,
@@ -826,7 +826,7 @@ static struct snd_soc_codec_driver soc_codec_dev_wm8988 = {
 	.num_dapm_routes = ARRAY_SIZE(wm8988_dapm_routes),
 };
 
-static struct regmap_config wm8988_regmap = {
+static const struct regmap_config wm8988_regmap = {
 	.reg_bits = 7,
 	.val_bits = 9,
 

sound/soc/codecs/wm8995.c

@@ -44,7 +44,7 @@ static const char *wm8995_supply_names[WM8995_NUM_SUPPLIES] = {
 	"MICVDD"
 };
 
-static struct reg_default wm8995_reg_defaults[] = {
+static const struct reg_default wm8995_reg_defaults[] = {
 	{ 0, 0x8995 },
 	{ 5, 0x0100 },
 	{ 16, 0x000b },
@@ -2186,7 +2186,7 @@ static struct snd_soc_dai_driver wm8995_dai[] = {
 	}
 };
 
-static struct snd_soc_codec_driver soc_codec_dev_wm8995 = {
+static const struct snd_soc_codec_driver soc_codec_dev_wm8995 = {
 	.probe = wm8995_probe,
 	.remove = wm8995_remove,
 	.set_bias_level = wm8995_set_bias_level,
@@ -2200,7 +2200,7 @@ static struct snd_soc_codec_driver soc_codec_dev_wm8995 = {
 	.num_dapm_routes = ARRAY_SIZE(wm8995_intercon),
 };
 
-static struct regmap_config wm8995_regmap = {
+static const struct regmap_config wm8995_regmap = {
 	.reg_bits = 16,
 	.val_bits = 16,
 

sound/soc/xtensa/Kconfig

+config SND_SOC_XTFPGA_I2S
+	tristate "XTFPGA I2S master"
+	select REGMAP_MMIO
+	help
+	  Say Y or M if you want to add support for codecs attached to the
+	  I2S interface on XTFPGA daughter board. You will also need to select
+	  the drivers for the rest of XTFPGA audio subsystem.

sound/soc/xtensa/Makefile

+snd-soc-xtfpga-i2s-objs := xtfpga-i2s.o
+
+obj-$(CONFIG_SND_SOC_XTFPGA_I2S) += snd-soc-xtfpga-i2s.o