Skip to content

L
linux
Commit f629b38b authored by Bartlomiej Zolnierkiewicz's avatar Bartlomiej Zolnierkiewicz
Browse files
Options

au1xxx-ide: fix MWDMA support 

Always use "fast" MWDMA support and remove dma_{black,white}_list
(they were based on completely bogus ->ide_dma_check implementation
which didn't set neither the host controller timings nor the device
for the desired transfer mode).
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 63158d5c
Hide whitespace changes
Inline Side-by-side
Showing with 2 additions and 135 deletions
Documentation/mips/AU1xxx_IDE.README
View file @ f629b38b
......@@ -46,8 +46,6 @@ Two files are introduced:
a) 'include/asm-mips/mach-au1x00/au1xxx_ide.h'
containes : struct _auide_hwif
struct drive_list_entry dma_white_list
struct drive_list_entry dma_black_list
timing parameters for PIO mode 0/1/2/3/4
timing parameters for MWDMA 0/1/2
......@@ -63,12 +61,6 @@ Four configs variables are introduced:
CONFIG_BLK_DEV_IDE_AU1XXX_SEQTS_PER_RQ - maximum transfer size
per descriptor
If MWDMA is enabled and the connected hard disc is not on the white list, the
kernel switches to a "safe mwdma mode" at boot time. In this mode the IDE
performance is substantial slower then in full speed mwdma. In this case
please add your hard disc to the white list (follow instruction from 'ADD NEW
HARD DISC TO WHITE OR BLACK LIST' section).
SUPPORTED IDE MODES
-------------------
......@@ -120,44 +112,6 @@ CONFIG_IDEDMA_AUTO=y
Also undefine 'IDE_AU1XXX_BURSTMODE' in 'drivers/ide/mips/au1xxx-ide.c' to
disable the burst support on DBDMA controller.
ADD NEW HARD DISC TO WHITE OR BLACK LIST
----------------------------------------
Step 1 : detect the model name of your hard disc
a) connect your hard disc to the AU1XXX
b) boot your kernel and get the hard disc model.
Example boot log:
--snipped--
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Au1xxx IDE(builtin) configured for MWDMA2
Probing IDE interface ide0...
hda: Maxtor 6E040L0, ATA DISK drive
ide0 at 0xac800000-0xac800007,0xac8001c0 on irq 64
hda: max request size: 64KiB
hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, (U)DMA
--snipped--
In this example 'Maxtor 6E040L0'.
Step 2 : edit 'include/asm-mips/mach-au1x00/au1xxx_ide.h'
Add your hard disc to the dma_white_list or dma_black_list structur.
Step 3 : Recompile the kernel
Enable MWDMA support in the kernel configuration. Recompile the kernel and
reboot.
Step 4 : Tests
If you have add a hard disc to the white list, please run some stress tests
for verification.
ACKNOWLEDGMENTS
---------------
......
drivers/ide/mips/au1xxx-ide.c
View file @ f629b38b
......@@ -47,7 +47,6 @@
#define IDE_AU1XXX_BURSTMODE 1
static _auide_hwif auide_hwif;
static int dbdma_init_done;
static int auide_ddma_init(_auide_hwif *auide);
......@@ -315,35 +314,6 @@ static int auide_dma_setup(ide_drive_t *drive)
return 0;
}
static u8 auide_mdma_filter(ide_drive_t *drive)
{
/*
* FIXME: ->white_list and ->black_list are based on completely bogus
* ->ide_dma_check implementation which didn't set neither the host
* controller timings nor the device for the desired transfer mode.
*
* They should be either removed or 0x00 MWDMA mask should be
* returned for devices on the ->black_list.
*/
if (dbdma_init_done == 0) {
auide_hwif.white_list = ide_in_drive_list(drive->id,
dma_white_list);
auide_hwif.black_list = ide_in_drive_list(drive->id,
dma_black_list);
auide_hwif.drive = drive;
auide_ddma_init(&auide_hwif);
dbdma_init_done = 1;
}
/* Is the drive in our DMA black list? */
if (auide_hwif.black_list)
printk(KERN_WARNING "%s: Disabling DMA for %s (blacklisted)\n",
drive->name, drive->id->model);
return drive->hwif->mwdma_mask;
}
static int auide_dma_test_irq(ide_drive_t *drive)
{
if (drive->waiting_for_dma == 0)
......@@ -420,17 +390,8 @@ static int auide_ddma_init(_auide_hwif *auide) {
dev_id = AU1XXX_ATA_DDMA_REQ;
if (auide->white_list || auide->black_list) {
tsize = 8;
devwidth = 32;
}
else {
tsize = 1;
devwidth = 16;
printk(KERN_ERR "au1xxx-ide: %s is not on ide driver whitelist.\n",auide_hwif.drive->id->model);
printk(KERN_ERR " please read 'Documentation/mips/AU1xxx_IDE.README'");
}
tsize = 8; /* 1 */
devwidth = 32; /* 16 */
#ifdef IDE_AU1XXX_BURSTMODE
flags = DEV_FLAGS_SYNC | DEV_FLAGS_BURSTABLE;
......@@ -546,9 +507,6 @@ static void auide_setup_ports(hw_regs_t *hw, _auide_hwif *ahwif)
static const struct ide_port_ops au1xxx_port_ops = {
.set_pio_mode = au1xxx_set_pio_mode,
.set_dma_mode = auide_set_dma_mode,
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
.mdma_filter = auide_mdma_filter,
#endif
};
static const struct ide_port_info au1xxx_port_info = {
......@@ -648,10 +606,7 @@ static int au_ide_probe(struct device *dev)
auide_hwif.hwif = hwif;
hwif->hwif_data = &auide_hwif;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_PIO_DBDMA
auide_ddma_init(&auide_hwif);
dbdma_init_done = 1;
#endif
idx[0] = hwif->index;
......
include/asm-mips/mach-au1x00/au1xxx_ide.h
View file @ f629b38b
......@@ -70,7 +70,6 @@ typedef struct
ide_hwif_t *hwif;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
ide_drive_t *drive;
u8 white_list, black_list;
struct dbdma_cmd *dma_table_cpu;
dma_addr_t dma_table_dma;
#endif
......@@ -81,47 +80,6 @@ typedef struct
#endif
} _auide_hwif;
#ifdef CONFIG_BLK_DEV_IDE_AU1XXX_MDMA2_DBDMA
/* HD white list */
static const struct drive_list_entry dma_white_list [] = {
/*
* Hitachi
*/
{ "HITACHI_DK14FA-20" , NULL },
{ "HTS726060M9AT00" , NULL },
/*
* Maxtor
*/
{ "Maxtor 6E040L0" , NULL },
{ "Maxtor 6Y080P0" , NULL },
{ "Maxtor 6Y160P0" , NULL },
/*
* Seagate
*/
{ "ST3120026A" , NULL },
{ "ST320014A" , NULL },
{ "ST94011A" , NULL },
{ "ST340016A" , NULL },
/*
* Western Digital
*/
{ "WDC WD400UE-00HCT0" , NULL },
{ "WDC WD400JB-00JJC0" , NULL },
{ NULL , NULL }
};
/* HD black list */
static const struct drive_list_entry dma_black_list [] = {
/*
* Western Digital
*/
{ "WDC WD100EB-00CGH0" , NULL },
{ "WDC WD200BB-00AUA1" , NULL },
{ "WDC AC24300L" , NULL },
{ NULL , NULL }
};
#endif
/*******************************************************************************
* PIO Mode timing calculation : *
* *
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7