Commit f6a26ae7 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc board specific changes from Olof Johansson:
 "While we generally attempt to get rid of board specific files and
  replace them with device tree based descriptions, a lot of platforms
  have not come that far:

  In shmobile, we add two new board files because their recently started
  effort to add DT support has not proceeded enough to use it for all of
  the important hardware.

  In Kirkwood, we are adding support for new boards with a combination
  of DT and board file contents in multiple cases.

  pxa/mmp and imx are extending support for existing board files but not
  adding new ones."

Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
  ARM: shmobile: fix smp build
  ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
  kirkwood: Add iconnect support
  orion/kirkwood: create a generic function for gpio led blinking
  kirkwood/orion: fix orion_gpio_set_blink
  ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
  kirkwood: Allow nand to be configured via. devicetree
  mtd: Add orion_nand devicetree bindings
  ARM: kirkwood: Basic support for DNS-320 and DNS-325
  ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
  ARM: mach-shmobile: Use DT_MACHINE for KZM9G
  ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
  ARM: pxa: Use REGULATOR_SUPPLY macro
  ARM: mach-shmobile: kzm9g: enable SMP boot
  ARM: mach-shmobile: kzm9g: defconfig update
  ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
  ARM: mach-shmobile: kzm9g: add SDHI support
  ARM: mach-shmobile: kzm9g: add MMCIF support
  ARM: mach-shmobile: kzm9g: correct screen direction
  ARM: mach-shmobile: sh73a0.h: add GPIO_NR
  ...
parents cdd3a354 48a5765e
NAND support for Marvell Orion SoC platforms
Required properties:
- compatible : "mrvl,orion-nand".
- reg : Base physical address of the NAND and length of memory mapped
region
Optional properties:
- cle : Address line number connected to CLE. Default is 0
- ale : Address line number connected to ALE. Default is 1
- bank-width : Width in bytes of the device. Default is 1
- chip-delay : Chip dependent delay for transferring data from array to read
registers in usecs
The device tree may optionally contain sub-nodes describing partitions of the
address space. See partition.txt for more detail.
Example:
nand@f4000000 {
#address-cells = <1>;
#size-cells = <1>;
cle = <0>;
ale = <1>;
bank-width = <1>;
chip-delay = <25>;
compatible = "mrvl,orion-nand";
reg = <0xf4000000 0x400>;
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
read-only;
};
partition@100000 {
label = "uImage";
reg = <0x0100000 0x200000>;
};
partition@300000 {
label = "dtb";
reg = <0x0300000 0x100000>;
};
partition@400000 {
label = "root";
reg = <0x0400000 0x7d00000>;
};
};
/dts-v1/;
/include/ "kirkwood.dtsi"
/ {
model = "D-Link DNS-320 NAS (Rev A1)";
compatible = "dlink,dns-320-a1", "dlink,dns-320", "dlink,dns-kirkwood", "mrvl,kirkwood-88f6281", "mrvl,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x8000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
};
ocp@f1000000 {
serial@12000 {
clock-frequency = <166666667>;
status = "okay";
};
serial@12100 {
clock-frequency = <166666667>;
status = "okay";
};
nand@3000000 {
status = "okay";
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
read-only;
};
partition@100000 {
label = "uImage";
reg = <0x0100000 0x500000>;
};
partition@600000 {
label = "ramdisk";
reg = <0x0600000 0x500000>;
};
partition@b00000 {
label = "image";
reg = <0x0b00000 0x6600000>;
};
partition@7100000 {
label = "mini firmware";
reg = <0x7100000 0xa00000>;
};
partition@7b00000 {
label = "config";
reg = <0x7b00000 0x500000>;
};
};
};
};
/dts-v1/;
/include/ "kirkwood.dtsi"
/ {
model = "D-Link DNS-325 NAS (Rev A1)";
compatible = "dlink,dns-325-a1", "dlink,dns-325", "dlink,dns-kirkwood", "mrvl,kirkwood-88f6281", "mrvl,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
};
ocp@f1000000 {
serial@12000 {
clock-frequency = <200000000>;
status = "okay";
};
nand@3000000 {
status = "okay";
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
read-only;
};
partition@100000 {
label = "uImage";
reg = <0x0100000 0x500000>;
};
partition@600000 {
label = "ramdisk";
reg = <0x0600000 0x500000>;
};
partition@b00000 {
label = "image";
reg = <0x0b00000 0x6600000>;
};
partition@7100000 {
label = "mini firmware";
reg = <0x7100000 0xa00000>;
};
partition@7b00000 {
label = "config";
reg = <0x7b00000 0x500000>;
};
};
};
};
/dts-v1/;
/include/ "kirkwood.dtsi"
/ {
model = "RaidSonic ICY BOX IB-NAS62x0 (Rev B)";
compatible = "raidsonic,ib-nas6210-b", "raidsonic,ib-nas6220-b", "raidsonic,ib-nas6210", "raidsonic,ib-nas6220", "raidsonic,ib-nas62x0", "mrvl,kirkwood-88f6281", "mrvl,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
};
ocp@f1000000 {
serial@12000 {
clock-frequency = <200000000>;
status = "okay";
};
nand@3000000 {
status = "okay";
partition@0 {
label = "u-boot";
reg = <0x0000000 0x100000>;
};
partition@100000 {
label = "uImage";
reg = <0x0100000 0x600000>;
};
partition@700000 {
label = "root";
reg = <0x0700000 0xf900000>;
};
};
};
};
/dts-v1/;
/include/ "kirkwood.dtsi"
/ {
model = "Iomega Iconnect";
compatible = "iom,iconnect-1.1", "iom,iconnect", "mrvl,kirkwood-88f6281", "mrvl,kirkwood";
memory {
device_type = "memory";
reg = <0x00000000 0x10000000>;
};
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk mtdparts=orion_nand:0xc0000@0x0(uboot),0x20000@0xa0000(env),0x300000@0x100000(zImage),0x300000@0x540000(initrd),0x1f400000@0x980000(boot)";
linux,initrd-start = <0x4500040>;
linux,initrd-end = <0x4800000>;
};
ocp@f1000000 {
serial@12000 {
clock-frequency = <200000000>;
status = "ok";
};
};
};
......@@ -5,7 +5,7 @@ / {
ocp@f1000000 {
compatible = "simple-bus";
ranges = <0 0xf1000000 0x1000000>;
ranges = <0 0xf1000000 0x4000000>;
#address-cells = <1>;
#size-cells = <1>;
......@@ -32,5 +32,18 @@ rtc@10300 {
reg = <0x10300 0x20>;
interrupts = <53>;
};
nand@3000000 {
#address-cells = <1>;
#size-cells = <1>;
cle = <0>;
ale = <1>;
bank-width = <1>;
compatible = "mrvl,orion-nand";
reg = <0x3000000 0x400>;
chip-delay = <25>;
/* set partition map and/or chip-delay in board dts */
status = "disabled";
};
};
};
/*
* Device Tree Source for the armadillo 800 eva board
*
* Copyright (C) 2012 Renesas Solutions Corp.
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
* kind, whether express or implied.
*/
/dts-v1/;
/include/ "skeleton.dtsi"
/ {
model = "armadillo 800 eva";
compatible = "renesas,armadillo800eva";
memory {
device_type = "memory";
reg = <0x40000000 0x20000000>;
};
};
/*
* Device Tree Source for the KZM-A9-GT board
*
* Copyright (C) 2012 Renesas Solutions Corp.
*
* This file is licensed under the terms of the GNU General Public License
* version 2. This program is licensed "as is" without any warranty of any
* kind, whether express or implied.
*/
/dts-v1/;
/include/ "skeleton.dtsi"
/ {
model = "KZM-A9-GT";
compatible = "renesas,kzm9g", "renesas,sh73a0";
memory {
device_type = "memory";
reg = <0x41000000 0x1e800000>;
};
};
CONFIG_EXPERIMENTAL=y
CONFIG_SYSVIPC=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
# CONFIG_UTS_NS is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
CONFIG_MODULE_FORCE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_SHMOBILE=y
CONFIG_ARCH_R8A7740=y
CONFIG_MACH_ARMADILLO800EVA=y
# CONFIG_SH_TIMER_TMU is not set
# CONFIG_ARM_THUMB is not set
CONFIG_CPU_BPREDICT_DISABLE=y
# CONFIG_CACHE_L2X0 is not set
CONFIG_ARM_ERRATA_430973=y
CONFIG_ARM_ERRATA_458693=y
CONFIG_ARM_ERRATA_460075=y
CONFIG_ARM_ERRATA_720789=y
CONFIG_ARM_ERRATA_743622=y
CONFIG_ARM_ERRATA_751472=y
CONFIG_ARM_ERRATA_754322=y
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
CONFIG_FORCE_MAX_ZONEORDER=13
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
CONFIG_CMDLINE_FORCE=y
CONFIG_KEXEC=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
# CONFIG_SUSPEND is not set
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_MD=y
CONFIG_BLK_DEV_DM=y
CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_VENDOR_CHELSIO is not set
# CONFIG_NET_VENDOR_CIRRUS is not set
# CONFIG_NET_VENDOR_FARADAY is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set
# CONFIG_NET_VENDOR_MICREL is not set
# CONFIG_NET_VENDOR_NATSEMI is not set
CONFIG_SH_ETH=y
# CONFIG_NET_VENDOR_SEEQ is not set
# CONFIG_NET_VENDOR_SMSC is not set
# CONFIG_NET_VENDOR_STMICRO is not set
# CONFIG_WLAN is not set
# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_KEYBOARD_ATKBD is not set
CONFIG_KEYBOARD_GPIO=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ST1232=y
# CONFIG_SERIO is not set
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_SH_SCI=y
CONFIG_SERIAL_SH_SCI_NR_UARTS=8
CONFIG_SERIAL_SH_SCI_CONSOLE=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C=y
CONFIG_I2C_SH_MOBILE=y
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FB_MODE_HELPERS=y
CONFIG_FB_SH_MOBILE_LCDC=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
CONFIG_LOGO=y
# CONFIG_LOGO_LINUX_MONO is not set
# CONFIG_LOGO_LINUX_VGA16 is not set
CONFIG_SOUND=y
CONFIG_SND=y
# CONFIG_SND_SUPPORT_OLD_API is not set
# CONFIG_SND_VERBOSE_PROCFS is not set
# CONFIG_SND_DRIVERS is not set
# CONFIG_SND_ARM is not set
CONFIG_SND_SOC=y
CONFIG_SND_SOC_SH4_FSI=y
# CONFIG_HID_SUPPORT is not set
CONFIG_USB=y
# CONFIG_USB_DEVICE_CLASS is not set
CONFIG_USB_RENESAS_USBHS=y
CONFIG_USB_GADGET=y
CONFIG_USB_RENESAS_USBHS_UDC=y
CONFIG_USB_ETH=m
CONFIG_MMC=y
CONFIG_MMC_SDHI=y
CONFIG_MMC_SH_MMCIF=y
CONFIG_UIO=y
CONFIG_UIO_PDRV_GENIRQ=y
# CONFIG_DNOTIFY is not set
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_TMPFS=y
# CONFIG_MISC_FILESYSTEMS is not set
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_V4_1=y
CONFIG_ROOT_NFS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
# CONFIG_ARM_UNWIND is not set
CONFIG_CRYPTO=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_DES=y
CONFIG_CRYPTO_ANSI_CPRNG=y
CONFIG_XZ_DEC=y
......@@ -92,6 +92,7 @@ CONFIG_INPUT_EVDEV=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ADS7846=m
CONFIG_TOUCHSCREEN_MC13783=m
# CONFIG_SERIO is not set
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250=m
......@@ -107,7 +108,8 @@ CONFIG_SPI_SPIDEV=y
CONFIG_W1=y
CONFIG_W1_MASTER_MXC=y
CONFIG_W1_SLAVE_THERM=y
# CONFIG_HWMON is not set
CONFIG_HWMON=m
CONFIG_SENSORS_MC13783_ADC=m
CONFIG_WATCHDOG=y
CONFIG_IMX2_WDT=y
CONFIG_MFD_MC13XXX=y
......
# CONFIG_ARM_PATCH_PHYS_VIRT is not set
CONFIG_EXPERIMENTAL=y
# CONFIG_LOCALVERSION_AUTO is not set
CONFIG_SYSVIPC=y
CONFIG_IKCONFIG=y
CONFIG_IKCONFIG_PROC=y
CONFIG_LOG_BUF_SHIFT=16
CONFIG_NAMESPACES=y
# CONFIG_UTS_NS is not set
# CONFIG_IPC_NS is not set
# CONFIG_USER_NS is not set
# CONFIG_PID_NS is not set
# CONFIG_NET_NS is not set
CONFIG_CC_OPTIMIZE_FOR_SIZE=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_EMBEDDED=y
CONFIG_SLAB=y
CONFIG_MODULES=y
CONFIG_MODULE_FORCE_LOAD=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_ARCH_SHMOBILE=y
CONFIG_KEYBOARD_GPIO_POLLED=y
CONFIG_ARCH_SH73A0=y
CONFIG_MACH_KZM9G=y
CONFIG_MEMORY_START=0x41000000
CONFIG_MEMORY_SIZE=0x1f000000
CONFIG_ARM_ERRATA_743622=y
CONFIG_ARM_ERRATA_754322=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_SCHED_MC=y
CONFIG_PREEMPT=y
CONFIG_AEABI=y
# CONFIG_OABI_COMPAT is not set
CONFIG_HIGHMEM=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="console=tty0 console=ttySC4,115200 root=/dev/nfs ip=dhcp ignore_loglevel earlyprintk=sh-sci.4,115200"
CONFIG_KEXEC=y
CONFIG_VFP=y
CONFIG_NEON=y
# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
CONFIG_PM_RUNTIME=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
# CONFIG_INET_XFRM_MODE_TUNNEL is not set
# CONFIG_INET_XFRM_MODE_BEET is not set
# CONFIG_INET_LRO is not set
# CONFIG_INET_DIAG is not set
# CONFIG_IPV6 is not set
CONFIG_IRDA=y
CONFIG_SH_IRDA=y
# CONFIG_WIRELESS is not set
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_NETDEVICES=y
CONFIG_SMSC911X=y
# CONFIG_WLAN is not set
CONFIG_INPUT_SPARSEKMAP=y
# CONFIG_INPUT_MOUSEDEV is not set
CONFIG_INPUT_EVDEV=y
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_TOUCHSCREEN_ST1232=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_SH_SCI=y
CONFIG_SERIAL_SH_SCI_NR_UARTS=9
CONFIG_SERIAL_SH_SCI_CONSOLE=y
# CONFIG_HW_RANDOM is not set
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_SH_MOBILE=y
CONFIG_GPIO_PCF857X=y
# CONFIG_HWMON is not set
CONFIG_FB=y
CONFIG_FB_SH_MOBILE_LCDC=y
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_LOGO=y
CONFIG_FB_SH_MOBILE_MERAM=y
CONFIG_SOUND=y
CONFIG_SND=y
# CONFIG_SND_SUPPORT_OLD_API is not set
# CONFIG_SND_VERBOSE_PROCFS is not set
# CONFIG_SND_DRIVERS is not set
# CONFIG_SND_ARM is not set
# CONFIG_SND_USB is not set
CONFIG_SND_SOC=y
CONFIG_SND_SOC_SH4_FSI=y
# CONFIG_HID_SUPPORT is not set
CONFIG_USB=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_R8A66597_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_MMC=y
# CONFIG_MMC_BLOCK_BOUNCE is not set
CONFIG_MMC_SDHI=y
CONFIG_MMC_SH_MMCIF=y
CONFIG_NEW_LEDS=y
CONFIG_LEDS_CLASS=y
CONFIG_RTC_CLASS=y
CONFIG_DMADEVICES=y
CONFIG_SH_DMAE=y
CONFIG_ASYNC_TX_DMA=y
CONFIG_STAGING=y
# CONFIG_DNOTIFY is not set
# CONFIG_INOTIFY_USER is not set
CONFIG_VFAT_FS=y
CONFIG_TMPFS=y
# CONFIG_MISC_FILESYSTEMS is not set
CONFIG_NFS_FS=y
CONFIG_NFS_V3=y
CONFIG_NFS_V3_ACL=y
CONFIG_NFS_V4=y
CONFIG_NFS_V4_1=y
CONFIG_ROOT_NFS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
# CONFIG_ENABLE_WARN_DEPRECATED is not set
# CONFIG_ENABLE_MUST_CHECK is not set
# CONFIG_SCHED_DEBUG is not set
# CONFIG_DEBUG_PREEMPT is not set
# CONFIG_DEBUG_BUGVERBOSE is not set
# CONFIG_FTRACE is not set
# CONFIG_ARM_UNWIND is not set
CONFIG_CRYPTO=y
CONFIG_CRYPTO_CBC=y
CONFIG_CRYPTO_MD5=y
CONFIG_CRYPTO_DES=y
CONFIG_CRC16=y
......@@ -98,6 +98,7 @@ CONFIG_LIBERTAS_USB=m
CONFIG_LIBERTAS_SDIO=m
CONFIG_LIBERTAS_DEBUG=y
CONFIG_USB_USBNET=y
CONFIG_USB_NET_SMSC95XX=y
CONFIG_USB_ALI_M5632=y
CONFIG_USB_AN2720=y
CONFIG_USB_EPSON2888=y
......@@ -175,6 +176,7 @@ CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_SUSPEND=y
CONFIG_USB_MON=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
CONFIG_USB_LIBUSUAL=y
......
......@@ -200,6 +200,7 @@ config MACH_SMDKV310
select S3C_DEV_HSMMC2
select S3C_DEV_HSMMC3
select SAMSUNG_DEV_BACKLIGHT
select EXYNOS_DEV_DRM
select EXYNOS4_DEV_AHCI
select SAMSUNG_DEV_KEYPAD
select EXYNOS4_DEV_DMA
......@@ -255,6 +256,7 @@ config MACH_UNIVERSAL_C210
select S5P_DEV_ONENAND
select S5P_DEV_TV
select EXYNOS4_DEV_DMA
select EXYNOS_DEV_DRM
select EXYNOS4_SETUP_FIMD0
select EXYNOS4_SETUP_I2C1
select EXYNOS4_SETUP_I2C3
......@@ -291,6 +293,7 @@ config MACH_NURI
select S5P_DEV_USB_EHCI
select S5P_SETUP_MIPIPHY
select EXYNOS4_DEV_DMA
select EXYNOS_DEV_DRM
select EXYNOS4_SETUP_FIMC
select EXYNOS4_SETUP_FIMD0
select EXYNOS4_SETUP_I2C1
......@@ -325,6 +328,7 @@ config MACH_ORIGEN
select S5P_DEV_USB_EHCI
select SAMSUNG_DEV_BACKLIGHT
select SAMSUNG_DEV_PWM
select EXYNOS_DEV_DRM
select EXYNOS4_DEV_DMA
select EXYNOS4_DEV_USB_OHCI
select EXYNOS4_SETUP_FIMD0
......@@ -345,6 +349,11 @@ config MACH_SMDK4212
select S3C_DEV_I2C7
select S3C_DEV_RTC
select S3C_DEV_WDT
select S5P_DEV_FIMC0
select S5P_DEV_FIMC1
select S5P_DEV_FIMC2
select S5P_DEV_FIMC3
select S5P_DEV_MFC
select SAMSUNG_DEV_BACKLIGHT
select SAMSUNG_DEV_KEYPAD
select SAMSUNG_DEV_PWM
......
......@@ -25,6 +25,7 @@
#include <linux/mmc/host.h>
#include <linux/fb.h>
#include <linux/pwm_backlight.h>
#include <drm/exynos_drm.h>
#include <video/platform_lcd.h>
#include <media/m5mols.h>
......@@ -210,6 +211,29 @@ static struct platform_device nuri_gpio_keys = {
},
};
#ifdef CONFIG_DRM_EXYNOS
static struct exynos_drm_fimd_pdata drm_fimd_pdata = {
.panel = {
.timing = {
.xres = 1024,
.yres = 600,
.hsync_len = 40,
.left_margin = 79,
.right_margin = 200,
.vsync_len = 10,
.upper_margin = 10,
.lower_margin = 11,
.refresh = 60,
},
},
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB |
VIDCON0_CLKSEL_LCD,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.default_win = 3,
.bpp = 32,
};
#else
/* Frame Buffer */
static struct s3c_fb_pd_win nuri_fb_win0 = {
.win_mode = {
......@@ -236,6 +260,7 @@ static struct s3c_fb_platdata nuri_fb_pdata __initdata = {
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.setup_gpio = exynos4_fimd0_gpio_setup_24bpp,
};
#endif
static void nuri_lcd_power_on(struct plat_lcd_data *pd, unsigned int power)
{
......@@ -1299,6 +1324,9 @@ static struct platform_device *nuri_devices[] __initdata = {
&cam_vdda_fixed_rdev,
&cam_8m_12v_fixed_rdev,
&exynos4_bus_devfreq,
#ifdef CONFIG_DRM_EXYNOS
&exynos_device_drm,
#endif
};
static void __init nuri_map_io(void)
......@@ -1331,7 +1359,12 @@ static void __init nuri_machine_init(void)
i2c_register_board_info(9, i2c9_devs, ARRAY_SIZE(i2c9_devs));
s3c_i2c6_set_platdata(&nuri_i2c6_platdata);
#ifdef CONFIG_DRM_EXYNOS
s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
exynos4_fimd0_gpio_setup_24bpp();
#else
s5p_fimd0_set_platdata(&nuri_fb_pdata);
#endif
nuri_camera_init();
......
......@@ -45,6 +45,7 @@
#include <mach/ohci.h>
#include <mach/map.h>
#include <drm/exynos_drm.h>
#include "common.h"
/* Following are default values for UCON, ULCON and UFCON UART registers */
......@@ -581,6 +582,27 @@ static struct platform_device origen_lcd_hv070wsa = {
.dev.platform_data = &origen_lcd_hv070wsa_data,
};
#ifdef CONFIG_DRM_EXYNOS
static struct exynos_drm_fimd_pdata drm_fimd_pdata = {
.panel = {
.timing = {
.left_margin = 64,
.right_margin = 16,
.upper_margin = 64,
.lower_margin = 16,
.hsync_len = 48,
.vsync_len = 3,
.xres = 1024,
.yres = 600,
},
},
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC |
VIDCON1_INV_VCLK,
.default_win = 0,
.bpp = 32,
};
#else
static struct s3c_fb_pd_win origen_fb_win0 = {
.win_mode = {
.left_margin = 64,
......@@ -594,6 +616,8 @@ static struct s3c_fb_pd_win origen_fb_win0 = {
},
.max_bpp = 32,
.default_bpp = 24,
.virtual_x = 1024,
.virtual_y = 2 * 600,
};
static struct s3c_fb_platdata origen_lcd_pdata __initdata = {
......@@ -603,9 +627,10 @@ static struct s3c_fb_platdata origen_lcd_pdata __initdata = {
VIDCON1_INV_VCLK,
.setup_gpio = exynos4_fimd0_gpio_setup_24bpp,
};
#endif
/* Bluetooth rfkill gpio platform data */
struct rfkill_gpio_platform_data origen_bt_pdata = {
static struct rfkill_gpio_platform_data origen_bt_pdata = {
.reset_gpio = EXYNOS4_GPX2(2),
.shutdown_gpio = -1,
.type = RFKILL_TYPE_BLUETOOTH,
......@@ -642,6 +667,9 @@ static struct platform_device *origen_devices[] __initdata = {
&s5p_device_mfc_l,
&s5p_device_mfc_r,
&s5p_device_mixer,
#ifdef CONFIG_DRM_EXYNOS
&exynos_device_drm,
#endif
&exynos4_device_ohci,
&origen_device_gpiokeys,
&origen_lcd_hv070wsa,
......@@ -717,7 +745,12 @@ static void __init origen_machine_init(void)
s5p_tv_setup();
s5p_i2c_hdmiphy_set_platdata(NULL);
#ifdef CONFIG_DRM_EXYNOS
s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
exynos4_fimd0_gpio_setup_24bpp();
#else
s5p_fimd0_set_platdata(&origen_lcd_pdata);
#endif
platform_add_devices(origen_devices, ARRAY_SIZE(origen_devices));
......
......@@ -31,6 +31,7 @@
#include <plat/gpio-cfg.h>
#include <plat/iic.h>
#include <plat/keypad.h>
#include <plat/mfc.h>
#include <plat/regs-serial.h>
#include <plat/sdhci.h>
......@@ -242,6 +243,14 @@ static struct platform_device *smdk4x12_devices[] __initdata = {
&s3c_device_i2c7,
&s3c_device_rtc,
&s3c_device_wdt,
&s5p_device_fimc0,
&s5p_device_fimc1,
&s5p_device_fimc2,
&s5p_device_fimc3,
&s5p_device_fimc_md,
&s5p_device_mfc,
&s5p_device_mfc_l,
&s5p_device_mfc_r,
&samsung_device_keypad,
};
......@@ -254,6 +263,11 @@ static void __init smdk4x12_map_io(void)
s3c24xx_init_uarts(smdk4x12_uartcfgs, ARRAY_SIZE(smdk4x12_uartcfgs));
}
static void __init smdk4x12_reserve(void)
{
s5p_mfc_reserve_mem(0x43000000, 8 << 20, 0x51000000, 8 << 20);
}
static void __init smdk4x12_machine_init(void)
{
s3c_i2c0_set_platdata(NULL);
......@@ -291,6 +305,7 @@ MACHINE_START(SMDK4212, "SMDK4212")
.init_machine = smdk4x12_machine_init,
.timer = &exynos4_timer,
.restart = exynos4_restart,
.reserve = &smdk4x12_reserve,
MACHINE_END
MACHINE_START(SMDK4412, "SMDK4412")
......@@ -303,4 +318,5 @@ MACHINE_START(SMDK4412, "SMDK4412")
.init_machine = smdk4x12_machine_init,
.timer = &exynos4_timer,
.restart = exynos4_restart,
.reserve = &smdk4x12_reserve,
MACHINE_END
......@@ -44,6 +44,7 @@
#include <mach/map.h>
#include <mach/ohci.h>
#include <drm/exynos_drm.h>
#include "common.h"
/* Following are default values for UCON, ULCON and UFCON UART registers */
......@@ -156,6 +157,26 @@ static struct platform_device smdkv310_lcd_lte480wv = {
.dev.platform_data = &smdkv310_lcd_lte480wv_data,
};
#ifdef CONFIG_DRM_EXYNOS
static struct exynos_drm_fimd_pdata drm_fimd_pdata = {
.panel = {
.timing = {
.left_margin = 13,
.right_margin = 8,
.upper_margin = 7,
.lower_margin = 5,
.hsync_len = 3,
.vsync_len = 1,
.xres = 800,
.yres = 480,
},
},
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.default_win = 0,
.bpp = 32,
};
#else
static struct s3c_fb_pd_win smdkv310_fb_win0 = {
.win_mode = {
.left_margin = 13,
......@@ -177,6 +198,7 @@ static struct s3c_fb_platdata smdkv310_lcd0_pdata __initdata = {
.vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.setup_gpio = exynos4_fimd0_gpio_setup_24bpp,
};
#endif
static struct resource smdkv310_smsc911x_resources[] = {
[0] = DEFINE_RES_MEM(EXYNOS4_PA_SROM_BANK(1), SZ_64K),
......@@ -262,6 +284,9 @@ static struct platform_device *smdkv310_devices[] __initdata = {
&s5p_device_fimc_md,
&s5p_device_g2d,
&s5p_device_jpeg,
#ifdef CONFIG_DRM_EXYNOS
&exynos_device_drm,
#endif
&exynos4_device_ac97,
&exynos4_device_i2s0,
&exynos4_device_ohci,
......@@ -353,7 +378,12 @@ static void __init smdkv310_machine_init(void)
samsung_keypad_set_platdata(&smdkv310_keypad_data);
samsung_bl_set(&smdkv310_bl_gpio_info, &smdkv310_bl_data);
#ifdef CONFIG_DRM_EXYNOS
s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
exynos4_fimd0_gpio_setup_24bpp();
#else
s5p_fimd0_set_platdata(&smdkv310_lcd0_pdata);
#endif
smdkv310_ehci_init();
smdkv310_ohci_init();
......
......@@ -23,6 +23,7 @@
#include <linux/i2c-gpio.h>
#include <linux/i2c/mcs.h>
#include <linux/i2c/atmel_mxt_ts.h>
#include <drm/exynos_drm.h>
#include <asm/mach/arch.h>
#include <asm/hardware/gic.h>
......@@ -811,6 +812,29 @@ static struct i2c_board_info i2c1_devs[] __initdata = {
/* Gyro, To be updated */
};
#ifdef CONFIG_DRM_EXYNOS
static struct exynos_drm_fimd_pdata drm_fimd_pdata = {
.panel = {
.timing = {
.left_margin = 16,
.right_margin = 16,
.upper_margin = 2,
.lower_margin = 28,
.hsync_len = 2,
.vsync_len = 1,
.xres = 480,
.yres = 800,
.refresh = 55,
},
},
.vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB |
VIDCON0_CLKSEL_LCD,
.vidcon1 = VIDCON1_INV_VCLK | VIDCON1_INV_VDEN
| VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.default_win = 3,
.bpp = 32,
};
#else
/* Frame Buffer */
static struct s3c_fb_pd_win universal_fb_win0 = {
.win_mode = {
......@@ -838,6 +862,7 @@ static struct s3c_fb_platdata universal_lcd_pdata __initdata = {
| VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
.setup_gpio = exynos4_fimd0_gpio_setup_24bpp,
};
#endif
static struct regulator_consumer_supply cam_vt_dio_supply =
REGULATOR_SUPPLY("vdd_core", "0-003c");
......@@ -1047,6 +1072,9 @@ static struct platform_device *universal_devices[] __initdata = {
&s5p_device_onenand,
&s5p_device_fimd0,
&s5p_device_jpeg,
#ifdef CONFIG_DRM_EXYNOS
&exynos_device_drm,
#endif
&s5p_device_mfc,
&s5p_device_mfc_l,
&s5p_device_mfc_r,
......@@ -1094,7 +1122,12 @@ static void __init universal_machine_init(void)
s5p_i2c_hdmiphy_set_platdata(NULL);
i2c_register_board_info(5, i2c5_devs, ARRAY_SIZE(i2c5_devs));
#ifdef CONFIG_DRM_EXYNOS
s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
exynos4_fimd0_gpio_setup_24bpp();
#else
s5p_fimd0_set_platdata(&universal_lcd_pdata);
#endif
universal_touchkey_init();
i2c_register_board_info(I2C_GPIO_BUS_12, i2c_gpio12_devs,
......
......@@ -163,6 +163,7 @@ config MACH_EUKREA_CPUIMX25SD
select SOC_IMX25
select IMX_HAVE_PLATFORM_FLEXCAN
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
select IMX_HAVE_PLATFORM_IMX2_WDT
select IMX_HAVE_PLATFORM_IMXDI_RTC
select IMX_HAVE_PLATFORM_IMX_FB
select IMX_HAVE_PLATFORM_IMX_I2C
......@@ -181,6 +182,7 @@ config MACH_EUKREA_MBIMXSD25_BASEBOARD
bool "Eukrea MBIMXSD development board"
select IMX_HAVE_PLATFORM_GPIO_KEYS
select IMX_HAVE_PLATFORM_IMX_SSI
select IMX_HAVE_PLATFORM_SPI_IMX
select LEDS_GPIO_REGISTER
help
This adds board specific devices that can be found on Eukrea's
......@@ -608,6 +610,7 @@ config MACH_EUKREA_MBIMXSD35_BASEBOARD
select IMX_HAVE_PLATFORM_GPIO_KEYS
select IMX_HAVE_PLATFORM_IMX_SSI
select IMX_HAVE_PLATFORM_IPU_CORE
select IMX_HAVE_PLATFORM_SPI_IMX
select LEDS_GPIO_REGISTER
help
This adds board specific devices that can be found on Eukrea's
......@@ -684,42 +687,13 @@ config MACH_MX51_3DS
Include support for MX51PDK (3DS) platform. This includes specific
configurations for the board and its peripherals.
config MACH_EUKREA_CPUIMX51
bool "Support Eukrea CPUIMX51 module"
select SOC_IMX51
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_MXC_EHCI
select IMX_HAVE_PLATFORM_MXC_NAND
select IMX_HAVE_PLATFORM_SPI_IMX
help
Include support for Eukrea CPUIMX51 platform. This includes
specific configurations for the module and its peripherals.
choice
prompt "Baseboard"
depends on MACH_EUKREA_CPUIMX51
default MACH_EUKREA_MBIMX51_BASEBOARD
config MACH_EUKREA_MBIMX51_BASEBOARD
prompt "Eukrea MBIMX51 development board"
bool
select IMX_HAVE_PLATFORM_IMX_KEYPAD
select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
select LEDS_GPIO_REGISTER
help
This adds board specific devices that can be found on Eukrea's
MBIMX51 evaluation board.
endchoice
config MACH_EUKREA_CPUIMX51SD
bool "Support Eukrea CPUIMX51SD module"
select SOC_IMX51
select IMX_HAVE_PLATFORM_FSL_USB2_UDC
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_IMX2_WDT
select IMX_HAVE_PLATFORM_MXC_EHCI
select IMX_HAVE_PLATFORM_MXC_NAND
select IMX_HAVE_PLATFORM_SPI_IMX
......@@ -735,6 +709,7 @@ choice
config MACH_EUKREA_MBIMXSD51_BASEBOARD
prompt "Eukrea MBIMXSD development board"
bool
select IMX_HAVE_PLATFORM_IMX_SSI
select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
select LEDS_GPIO_REGISTER
help
......
......@@ -83,10 +83,8 @@ obj-$(CONFIG_MACH_MX53_EVK) += mach-mx53_evk.o
obj-$(CONFIG_MACH_MX53_SMD) += mach-mx53_smd.o
obj-$(CONFIG_MACH_MX53_LOCO) += mach-mx53_loco.o
obj-$(CONFIG_MACH_MX53_ARD) += mach-mx53_ard.o
obj-$(CONFIG_MACH_EUKREA_CPUIMX51) += mach-cpuimx51.o
obj-$(CONFIG_MACH_EUKREA_MBIMX51_BASEBOARD) += eukrea_mbimx51-baseboard.o
obj-$(CONFIG_MACH_EUKREA_CPUIMX51SD) += mach-cpuimx51sd.o
obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd-baseboard.o
obj-$(CONFIG_MACH_EUKREA_MBIMXSD51_BASEBOARD) += eukrea_mbimxsd51-baseboard.o
obj-$(CONFIG_MX51_EFIKA_COMMON) += mx51_efika.o
obj-$(CONFIG_MACH_MX51_EFIKAMX) += mach-mx51_efikamx.o
obj-$(CONFIG_MACH_MX51_EFIKASB) += mach-mx51_efikasb.o
......
/*
*
* Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/serial_8250.h>
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/io.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/i2c/tsc2007.h>
#include <linux/leds.h>
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/iomux-mx51.h>
#include <asm/mach/arch.h>
#include "devices-imx51.h"
#define MBIMX51_TSC2007_GPIO IMX_GPIO_NR(3, 30)
#define MBIMX51_LED0 IMX_GPIO_NR(3, 5)
#define MBIMX51_LED1 IMX_GPIO_NR(3, 6)
#define MBIMX51_LED2 IMX_GPIO_NR(3, 7)
#define MBIMX51_LED3 IMX_GPIO_NR(3, 8)
static const struct gpio_led mbimx51_leds[] __initconst = {
{
.name = "led0",
.default_trigger = "heartbeat",
.active_low = 1,
.gpio = MBIMX51_LED0,
},
{
.name = "led1",
.default_trigger = "nand-disk",
.active_low = 1,
.gpio = MBIMX51_LED1,
},
{
.name = "led2",
.default_trigger = "mmc0",
.active_low = 1,
.gpio = MBIMX51_LED2,
},
{
.name = "led3",
.default_trigger = "default-on",
.active_low = 1,
.gpio = MBIMX51_LED3,
},
};
static const struct gpio_led_platform_data mbimx51_leds_info __initconst = {
.leds = mbimx51_leds,
.num_leds = ARRAY_SIZE(mbimx51_leds),
};
static iomux_v3_cfg_t mbimx51_pads[] = {
/* UART2 */
MX51_PAD_UART2_RXD__UART2_RXD,
MX51_PAD_UART2_TXD__UART2_TXD,
/* UART3 */
MX51_PAD_UART3_RXD__UART3_RXD,
MX51_PAD_UART3_TXD__UART3_TXD,
MX51_PAD_KEY_COL4__UART3_RTS,
MX51_PAD_KEY_COL5__UART3_CTS,
/* TSC2007 IRQ */
MX51_PAD_NANDF_D10__GPIO3_30,
/* LEDS */
MX51_PAD_DISPB2_SER_DIN__GPIO3_5,
MX51_PAD_DISPB2_SER_DIO__GPIO3_6,
MX51_PAD_DISPB2_SER_CLK__GPIO3_7,
MX51_PAD_DISPB2_SER_RS__GPIO3_8,
/* KPP */
MX51_PAD_KEY_ROW0__KEY_ROW0,
MX51_PAD_KEY_ROW1__KEY_ROW1,
MX51_PAD_KEY_ROW2__KEY_ROW2,
MX51_PAD_KEY_ROW3__KEY_ROW3,
MX51_PAD_KEY_COL0__KEY_COL0,
MX51_PAD_KEY_COL1__KEY_COL1,
MX51_PAD_KEY_COL2__KEY_COL2,
MX51_PAD_KEY_COL3__KEY_COL3,
/* SD 1 */
MX51_PAD_SD1_CMD__SD1_CMD,
MX51_PAD_SD1_CLK__SD1_CLK,
MX51_PAD_SD1_DATA0__SD1_DATA0,
MX51_PAD_SD1_DATA1__SD1_DATA1,
MX51_PAD_SD1_DATA2__SD1_DATA2,
MX51_PAD_SD1_DATA3__SD1_DATA3,
/* SD 2 */
MX51_PAD_SD2_CMD__SD2_CMD,
MX51_PAD_SD2_CLK__SD2_CLK,
MX51_PAD_SD2_DATA0__SD2_DATA0,
MX51_PAD_SD2_DATA1__SD2_DATA1,
MX51_PAD_SD2_DATA2__SD2_DATA2,
MX51_PAD_SD2_DATA3__SD2_DATA3,
};
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
static int mbimx51_keymap[] = {
KEY(0, 0, KEY_1),
KEY(0, 1, KEY_2),
KEY(0, 2, KEY_3),
KEY(0, 3, KEY_UP),
KEY(1, 0, KEY_4),
KEY(1, 1, KEY_5),
KEY(1, 2, KEY_6),
KEY(1, 3, KEY_LEFT),
KEY(2, 0, KEY_7),
KEY(2, 1, KEY_8),
KEY(2, 2, KEY_9),
KEY(2, 3, KEY_RIGHT),
KEY(3, 0, KEY_0),
KEY(3, 1, KEY_DOWN),
KEY(3, 2, KEY_ESC),
KEY(3, 3, KEY_ENTER),
};
static const struct matrix_keymap_data mbimx51_map_data __initconst = {
.keymap = mbimx51_keymap,
.keymap_size = ARRAY_SIZE(mbimx51_keymap),
};
static int tsc2007_get_pendown_state(void)
{
return !gpio_get_value(MBIMX51_TSC2007_GPIO);
}
struct tsc2007_platform_data tsc2007_data = {
.model = 2007,
.x_plate_ohms = 180,
.get_pendown_state = tsc2007_get_pendown_state,
};
static struct i2c_board_info mbimx51_i2c_devices[] = {
{
I2C_BOARD_INFO("tsc2007", 0x49),
.irq = IMX_GPIO_TO_IRQ(MBIMX51_TSC2007_GPIO),
.platform_data = &tsc2007_data,
}, {
I2C_BOARD_INFO("tlv320aic23", 0x1a),
},
};
/*
* baseboard initialization.
*/
void __init eukrea_mbimx51_baseboard_init(void)
{
mxc_iomux_v3_setup_multiple_pads(mbimx51_pads,
ARRAY_SIZE(mbimx51_pads));
imx51_add_imx_uart(1, NULL);
imx51_add_imx_uart(2, &uart_pdata);
gpio_request(MBIMX51_LED0, "LED0");
gpio_direction_output(MBIMX51_LED0, 1);
gpio_free(MBIMX51_LED0);
gpio_request(MBIMX51_LED1, "LED1");
gpio_direction_output(MBIMX51_LED1, 1);
gpio_free(MBIMX51_LED1);
gpio_request(MBIMX51_LED2, "LED2");
gpio_direction_output(MBIMX51_LED2, 1);
gpio_free(MBIMX51_LED2);
gpio_request(MBIMX51_LED3, "LED3");
gpio_direction_output(MBIMX51_LED3, 1);
gpio_free(MBIMX51_LED3);
gpio_led_register_device(-1, &mbimx51_leds_info);
imx51_add_imx_keypad(&mbimx51_map_data);
gpio_request(MBIMX51_TSC2007_GPIO, "tsc2007_irq");
gpio_direction_input(MBIMX51_TSC2007_GPIO);
irq_set_irq_type(gpio_to_irq(MBIMX51_TSC2007_GPIO),
IRQF_TRIGGER_FALLING);
i2c_register_board_info(1, mbimx51_i2c_devices,
ARRAY_SIZE(mbimx51_i2c_devices));
imx51_add_sdhci_esdhc_imx(0, NULL);
imx51_add_sdhci_esdhc_imx(1, NULL);
}
......@@ -23,6 +23,7 @@
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/spi/spi.h>
#include <video/platform_lcd.h>
#include <mach/hardware.h>
......@@ -87,12 +88,22 @@ static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
/* CAN */
MX25_PAD_GPIO_D__CAN2_RX,
MX25_PAD_GPIO_C__CAN2_TX,
/* SPI1 */
MX25_PAD_CSPI1_MOSI__CSPI1_MOSI,
MX25_PAD_CSPI1_MISO__CSPI1_MISO,
MX25_PAD_CSPI1_SS0__GPIO_1_16,
MX25_PAD_CSPI1_SS1__GPIO_1_17,
MX25_PAD_CSPI1_SCLK__CSPI1_SCLK,
MX25_PAD_CSPI1_RDY__GPIO_2_22,
};
#define GPIO_LED1 83
#define GPIO_SWITCH1 82
#define GPIO_SD1CD 52
#define GPIO_LCDPWR 26
#define GPIO_LED1 IMX_GPIO_NR(3, 19)
#define GPIO_SWITCH1 IMX_GPIO_NR(3, 18)
#define GPIO_SD1CD IMX_GPIO_NR(2, 20)
#define GPIO_LCDPWR IMX_GPIO_NR(1, 26)
#define GPIO_SPI1_SS0 IMX_GPIO_NR(1, 16)
#define GPIO_SPI1_SS1 IMX_GPIO_NR(1, 17)
#define GPIO_SPI1_IRQ IMX_GPIO_NR(2, 22)
static struct imx_fb_videomode eukrea_mximxsd_modes[] = {
{
......@@ -228,6 +239,30 @@ static struct esdhc_platform_data sd1_pdata = {
.wp_type = ESDHC_WP_NONE,
};
static struct spi_board_info eukrea_mbimxsd25_spi_board_info[] __initdata = {
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 0,
.mode = SPI_MODE_0,
},
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
.mode = SPI_MODE_0,
},
};
static int eukrea_mbimxsd25_spi_cs[] = {GPIO_SPI1_SS0, GPIO_SPI1_SS1};
static const struct spi_imx_master eukrea_mbimxsd25_spi0_data __initconst = {
.chipselect = eukrea_mbimxsd25_spi_cs,
.num_chipselect = ARRAY_SIZE(eukrea_mbimxsd25_spi_cs),
};
/*
* system init for baseboard usage. Will be called by cpuimx25 init.
*
......@@ -257,11 +292,17 @@ void __init eukrea_mbimxsd25_baseboard_init(void)
gpio_request(GPIO_LCDPWR, "LCDPWR");
gpio_direction_output(GPIO_LCDPWR, 1);
gpio_free(GPIO_SWITCH1);
i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
gpio_request(GPIO_SPI1_IRQ, "SPI1_IRQ");
gpio_direction_input(GPIO_SPI1_IRQ);
gpio_free(GPIO_SPI1_IRQ);
imx25_add_spi_imx0(&eukrea_mbimxsd25_spi0_data);
spi_register_board_info(eukrea_mbimxsd25_spi_board_info,
ARRAY_SIZE(eukrea_mbimxsd25_spi_board_info));
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
gpio_led_register_device(-1, &eukrea_mbimxsd_led_info);
imx_add_gpio_keys(&eukrea_mbimxsd_button_data);
......
......@@ -27,6 +27,7 @@
#include <linux/leds.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/spi/spi.h>
#include <video/platform_lcd.h>
#include <linux/i2c.h>
......@@ -158,12 +159,22 @@ static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
MX35_PAD_SD1_DATA3__ESDHC1_DAT3,
/* SD1 CD */
MX35_PAD_LD18__GPIO3_24,
/* SPI */
MX35_PAD_CSPI1_MOSI__CSPI1_MOSI,
MX35_PAD_CSPI1_MISO__CSPI1_MISO,
MX35_PAD_CSPI1_SS0__GPIO1_18,
MX35_PAD_CSPI1_SS1__GPIO1_19,
MX35_PAD_CSPI1_SCLK__CSPI1_SCLK,
MX35_PAD_CSPI1_SPI_RDY__GPIO3_5,
};
#define GPIO_LED1 IMX_GPIO_NR(3, 29)
#define GPIO_SWITCH1 IMX_GPIO_NR(3, 25)
#define GPIO_LCDPWR IMX_GPIO_NR(1, 4)
#define GPIO_SD1CD IMX_GPIO_NR(3, 24)
#define GPIO_SPI1_SS0 IMX_GPIO_NR(1, 18)
#define GPIO_SPI1_SS1 IMX_GPIO_NR(1, 19)
#define GPIO_SPI1_IRQ IMX_GPIO_NR(3, 5)
static void eukrea_mbimxsd_lcd_power_set(struct plat_lcd_data *pd,
unsigned int power)
......@@ -239,6 +250,30 @@ static struct esdhc_platform_data sd1_pdata = {
.wp_type = ESDHC_WP_NONE,
};
static struct spi_board_info eukrea_mbimxsd35_spi_board_info[] __initdata = {
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 0,
.mode = SPI_MODE_0,
},
{
.modalias = "spidev",
.max_speed_hz = 20000000,
.bus_num = 0,
.chip_select = 1,
.mode = SPI_MODE_0,
},
};
static int eukrea_mbimxsd35_spi_cs[] = {GPIO_SPI1_SS0, GPIO_SPI1_SS1};
static const struct spi_imx_master eukrea_mbimxsd35_spi0_data __initconst = {
.chipselect = eukrea_mbimxsd35_spi_cs,
.num_chipselect = ARRAY_SIZE(eukrea_mbimxsd35_spi_cs),
};
/*
* system init for baseboard usage. Will be called by cpuimx35 init.
*
......@@ -274,6 +309,13 @@ void __init eukrea_mbimxsd35_baseboard_init(void)
i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
gpio_request(GPIO_SPI1_IRQ, "SPI1_IRQ");
gpio_direction_input(GPIO_SPI1_IRQ);
gpio_free(GPIO_SPI1_IRQ);
imx35_add_spi_imx0(&eukrea_mbimxsd35_spi0_data);
spi_register_board_info(eukrea_mbimxsd35_spi_board_info,
ARRAY_SIZE(eukrea_mbimxsd35_spi_board_info));
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
gpio_led_register_device(-1, &eukrea_mbimxsd_led_info);
imx_add_gpio_keys(&eukrea_mbimxsd_button_data);
......
......@@ -28,6 +28,8 @@
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <video/platform_lcd.h>
#include <linux/backlight.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
......@@ -40,7 +42,7 @@
#include "devices-imx51.h"
static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
static iomux_v3_cfg_t eukrea_mbimxsd51_pads[] = {
/* LED */
MX51_PAD_NANDF_D10__GPIO3_30,
/* SWITCH */
......@@ -66,12 +68,64 @@ static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_PUS_22K_UP |
PAD_CTL_PKE | PAD_CTL_SRE_FAST |
PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
/* SSI */
MX51_PAD_AUD3_BB_TXD__AUD3_TXD,
MX51_PAD_AUD3_BB_RXD__AUD3_RXD,
MX51_PAD_AUD3_BB_CK__AUD3_TXC,
MX51_PAD_AUD3_BB_FS__AUD3_TXFS,
/* LCD Backlight */
MX51_PAD_DI1_D1_CS__GPIO3_4,
/* LCD RST */
MX51_PAD_CSI1_D9__GPIO3_13,
};
#define GPIO_LED1 IMX_GPIO_NR(3, 30)
#define GPIO_SWITCH1 IMX_GPIO_NR(3, 31)
#define GPIO_LCDRST IMX_GPIO_NR(3, 13)
#define GPIO_LCDBL IMX_GPIO_NR(3, 4)
static const struct gpio_led eukrea_mbimxsd_leds[] __initconst = {
static void eukrea_mbimxsd51_lcd_power_set(struct plat_lcd_data *pd,
unsigned int power)
{
if (power)
gpio_direction_output(GPIO_LCDRST, 1);
else
gpio_direction_output(GPIO_LCDRST, 0);
}
static struct plat_lcd_data eukrea_mbimxsd51_lcd_power_data = {
.set_power = eukrea_mbimxsd51_lcd_power_set,
};
static struct platform_device eukrea_mbimxsd51_lcd_powerdev = {
.name = "platform-lcd",
.dev.platform_data = &eukrea_mbimxsd51_lcd_power_data,
};
static void eukrea_mbimxsd51_bl_set_intensity(int intensity)
{
if (intensity)
gpio_direction_output(GPIO_LCDBL, 1);
else
gpio_direction_output(GPIO_LCDBL, 0);
}
static struct generic_bl_info eukrea_mbimxsd51_bl_info = {
.name = "eukrea_mbimxsd51-bl",
.max_intensity = 0xff,
.default_intensity = 0xff,
.set_bl_intensity = eukrea_mbimxsd51_bl_set_intensity,
};
static struct platform_device eukrea_mbimxsd51_bl_dev = {
.name = "generic-bl",
.id = 1,
.dev = {
.platform_data = &eukrea_mbimxsd51_bl_info,
},
};
static const struct gpio_led eukrea_mbimxsd51_leds[] __initconst = {
{
.name = "led1",
.default_trigger = "heartbeat",
......@@ -81,12 +135,12 @@ static const struct gpio_led eukrea_mbimxsd_leds[] __initconst = {
};
static const struct gpio_led_platform_data
eukrea_mbimxsd_led_info __initconst = {
.leds = eukrea_mbimxsd_leds,
.num_leds = ARRAY_SIZE(eukrea_mbimxsd_leds),
eukrea_mbimxsd51_led_info __initconst = {
.leds = eukrea_mbimxsd51_leds,
.num_leds = ARRAY_SIZE(eukrea_mbimxsd51_leds),
};
static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
static struct gpio_keys_button eukrea_mbimxsd51_gpio_buttons[] = {
{
.gpio = GPIO_SWITCH1,
.code = BTN_0,
......@@ -97,21 +151,39 @@ static struct gpio_keys_button eukrea_mbimxsd_gpio_buttons[] = {
};
static const struct gpio_keys_platform_data
eukrea_mbimxsd_button_data __initconst = {
.buttons = eukrea_mbimxsd_gpio_buttons,
.nbuttons = ARRAY_SIZE(eukrea_mbimxsd_gpio_buttons),
eukrea_mbimxsd51_button_data __initconst = {
.buttons = eukrea_mbimxsd51_gpio_buttons,
.nbuttons = ARRAY_SIZE(eukrea_mbimxsd51_gpio_buttons),
};
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
static struct i2c_board_info eukrea_mbimxsd51_i2c_devices[] = {
{
I2C_BOARD_INFO("tlv320aic23", 0x1a),
},
};
static const
struct imx_ssi_platform_data eukrea_mbimxsd51_ssi_pdata __initconst = {
.flags = IMX_SSI_SYN | IMX_SSI_NET | IMX_SSI_USE_I2S_SLAVE,
};
static int screen_type;
static int __init eukrea_mbimxsd51_screen_type(char *options)
{
if (!strcmp(options, "dvi"))
screen_type = 1;
else if (!strcmp(options, "tft"))
screen_type = 0;
return 0;
}
__setup("screen_type=", eukrea_mbimxsd51_screen_type);
/*
* system init for baseboard usage. Will be called by cpuimx51sd init.
*
......@@ -120,8 +192,8 @@ static struct i2c_board_info eukrea_mbimxsd_i2c_devices[] = {
*/
void __init eukrea_mbimxsd51_baseboard_init(void)
{
if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd_pads,
ARRAY_SIZE(eukrea_mbimxsd_pads)))
if (mxc_iomux_v3_setup_multiple_pads(eukrea_mbimxsd51_pads,
ARRAY_SIZE(eukrea_mbimxsd51_pads)))
printk(KERN_ERR "error setting mbimxsd pads !\n");
imx51_add_imx_uart(1, NULL);
......@@ -129,6 +201,8 @@ void __init eukrea_mbimxsd51_baseboard_init(void)
imx51_add_sdhci_esdhc_imx(0, NULL);
imx51_add_imx_ssi(0, &eukrea_mbimxsd51_ssi_pdata);
gpio_request(GPIO_LED1, "LED1");
gpio_direction_output(GPIO_LED1, 1);
gpio_free(GPIO_LED1);
......@@ -137,9 +211,21 @@ void __init eukrea_mbimxsd51_baseboard_init(void)
gpio_direction_input(GPIO_SWITCH1);
gpio_free(GPIO_SWITCH1);
i2c_register_board_info(0, eukrea_mbimxsd_i2c_devices,
ARRAY_SIZE(eukrea_mbimxsd_i2c_devices));
gpio_led_register_device(-1, &eukrea_mbimxsd_led_info);
imx_add_gpio_keys(&eukrea_mbimxsd_button_data);
gpio_request(GPIO_LCDRST, "LCDRST");
gpio_direction_output(GPIO_LCDRST, 0);
gpio_request(GPIO_LCDBL, "LCDBL");
gpio_direction_output(GPIO_LCDBL, 0);
if (!screen_type) {
platform_device_register(&eukrea_mbimxsd51_bl_dev);
platform_device_register(&eukrea_mbimxsd51_lcd_powerdev);
} else {
gpio_free(GPIO_LCDRST);
gpio_free(GPIO_LCDBL);
}
i2c_register_board_info(0, eukrea_mbimxsd51_i2c_devices,
ARRAY_SIZE(eukrea_mbimxsd51_i2c_devices));
gpio_led_register_device(-1, &eukrea_mbimxsd51_led_info);
imx_add_gpio_keys(&eukrea_mbimxsd51_button_data);
}
/*
*
* Copyright (C) 2010 Eric Bénard <eric@eukrea.com>
*
* based on board-mx51_babbage.c which is
* Copyright 2009 Freescale Semiconductor, Inc. All Rights Reserved.
* Copyright (C) 2009-2010 Amit Kucheria <amit.kucheria@canonical.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/serial_8250.h>
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/interrupt.h>
#include <mach/eukrea-baseboards.h>
#include <mach/common.h>
#include <mach/hardware.h>
#include <mach/iomux-mx51.h>
#include <asm/setup.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include "devices-imx51.h"
#define CPUIMX51_USBH1_STP IMX_GPIO_NR(1, 27)
#define CPUIMX51_QUARTA_GPIO IMX_GPIO_NR(3, 28)
#define CPUIMX51_QUARTB_GPIO IMX_GPIO_NR(3, 25)
#define CPUIMX51_QUARTC_GPIO IMX_GPIO_NR(3, 26)
#define CPUIMX51_QUARTD_GPIO IMX_GPIO_NR(3, 27)
#define CPUIMX51_QUART_XTAL 14745600
#define CPUIMX51_QUART_REGSHIFT 17
/* USB_CTRL_1 */
#define MX51_USB_CTRL_1_OFFSET 0x10
#define MX51_USB_CTRL_UH1_EXT_CLK_EN (1 << 25)
#define MX51_USB_PLLDIV_12_MHZ 0x00
#define MX51_USB_PLL_DIV_19_2_MHZ 0x01
#define MX51_USB_PLL_DIV_24_MHZ 0x02
static struct plat_serial8250_port serial_platform_data[] = {
{
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x400000),
.irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTA_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
.iotype = UPIO_MEM,
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x800000),
.irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTB_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
.iotype = UPIO_MEM,
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x1000000),
.irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTC_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
.iotype = UPIO_MEM,
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
.mapbase = (unsigned long)(MX51_CS1_BASE_ADDR + 0x2000000),
.irq = IMX_GPIO_TO_IRQ(CPUIMX51_QUARTD_GPIO),
.irqflags = IRQF_TRIGGER_HIGH,
.uartclk = CPUIMX51_QUART_XTAL,
.regshift = CPUIMX51_QUART_REGSHIFT,
.iotype = UPIO_MEM,
.flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST | UPF_IOREMAP,
}, {
}
};
static struct platform_device serial_device = {
.name = "serial8250",
.id = 0,
.dev = {
.platform_data = serial_platform_data,
},
};
static struct platform_device *devices[] __initdata = {
&serial_device,
};
static iomux_v3_cfg_t eukrea_cpuimx51_pads[] = {
/* UART1 */
MX51_PAD_UART1_RXD__UART1_RXD,
MX51_PAD_UART1_TXD__UART1_TXD,
MX51_PAD_UART1_RTS__UART1_RTS,
MX51_PAD_UART1_CTS__UART1_CTS,
/* I2C2 */
MX51_PAD_GPIO1_2__I2C2_SCL,
MX51_PAD_GPIO1_3__I2C2_SDA,
MX51_PAD_NANDF_D10__GPIO3_30,
/* QUART IRQ */
MX51_PAD_NANDF_D15__GPIO3_25,
MX51_PAD_NANDF_D14__GPIO3_26,
MX51_PAD_NANDF_D13__GPIO3_27,
MX51_PAD_NANDF_D12__GPIO3_28,
/* USB HOST1 */
MX51_PAD_USBH1_CLK__USBH1_CLK,
MX51_PAD_USBH1_DIR__USBH1_DIR,
MX51_PAD_USBH1_NXT__USBH1_NXT,
MX51_PAD_USBH1_DATA0__USBH1_DATA0,
MX51_PAD_USBH1_DATA1__USBH1_DATA1,
MX51_PAD_USBH1_DATA2__USBH1_DATA2,
MX51_PAD_USBH1_DATA3__USBH1_DATA3,
MX51_PAD_USBH1_DATA4__USBH1_DATA4,
MX51_PAD_USBH1_DATA5__USBH1_DATA5,
MX51_PAD_USBH1_DATA6__USBH1_DATA6,
MX51_PAD_USBH1_DATA7__USBH1_DATA7,
MX51_PAD_USBH1_STP__USBH1_STP,
};
static const struct mxc_nand_platform_data
eukrea_cpuimx51_nand_board_info __initconst = {
.width = 1,
.hw_ecc = 1,
.flash_bbt = 1,
};
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
static const
struct imxi2c_platform_data eukrea_cpuimx51_i2c_data __initconst = {
.bitrate = 100000,
};
static struct i2c_board_info eukrea_cpuimx51_i2c_devices[] = {
{
I2C_BOARD_INFO("pcf8563", 0x51),
},
};
/* This function is board specific as the bit mask for the plldiv will also
be different for other Freescale SoCs, thus a common bitmask is not
possible and cannot get place in /plat-mxc/ehci.c.*/
static int initialize_otg_port(struct platform_device *pdev)
{
u32 v;
void __iomem *usb_base;
void __iomem *usbother_base;
usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
if (!usb_base)
return -ENOMEM;
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
/* Set the PHY clock to 19.2MHz */
v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
v &= ~MX5_USB_UTMI_PHYCTRL1_PLLDIV_MASK;
v |= MX51_USB_PLL_DIV_19_2_MHZ;
__raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC2_OFFSET);
iounmap(usb_base);
mdelay(10);
return mx51_initialize_usb_hw(0, MXC_EHCI_INTERNAL_PHY);
}
static int initialize_usbh1_port(struct platform_device *pdev)
{
u32 v;
void __iomem *usb_base;
void __iomem *usbother_base;
usb_base = ioremap(MX51_USB_OTG_BASE_ADDR, SZ_4K);
if (!usb_base)
return -ENOMEM;
usbother_base = usb_base + MX5_USBOTHER_REGS_OFFSET;
/* The clock for the USBH1 ULPI port will come externally from the PHY. */
v = __raw_readl(usbother_base + MX51_USB_CTRL_1_OFFSET);
__raw_writel(v | MX51_USB_CTRL_UH1_EXT_CLK_EN, usbother_base + MX51_USB_CTRL_1_OFFSET);
iounmap(usb_base);
mdelay(10);
return mx51_initialize_usb_hw(1, MXC_EHCI_POWER_PINS_ENABLED |
MXC_EHCI_ITC_NO_THRESHOLD);
}
static const struct mxc_usbh_platform_data dr_utmi_config __initconst = {
.init = initialize_otg_port,
.portsc = MXC_EHCI_UTMI_16BIT,
};
static const struct fsl_usb2_platform_data usb_pdata __initconst = {
.operating_mode = FSL_USB2_DR_DEVICE,
.phy_mode = FSL_USB2_PHY_UTMI_WIDE,
};
static const struct mxc_usbh_platform_data usbh1_config __initconst = {
.init = initialize_usbh1_port,
.portsc = MXC_EHCI_MODE_ULPI,
};
static int otg_mode_host;
static int __init eukrea_cpuimx51_otg_mode(char *options)
{
if (!strcmp(options, "host"))
otg_mode_host = 1;
else if (!strcmp(options, "device"))
otg_mode_host = 0;
else
pr_info("otg_mode neither \"host\" nor \"device\". "
"Defaulting to device\n");
return 0;
}
__setup("otg_mode=", eukrea_cpuimx51_otg_mode);
/*
* Board specific initialization.
*/
static void __init eukrea_cpuimx51_init(void)
{
imx51_soc_init();
mxc_iomux_v3_setup_multiple_pads(eukrea_cpuimx51_pads,
ARRAY_SIZE(eukrea_cpuimx51_pads));
imx51_add_imx_uart(0, &uart_pdata);
imx51_add_mxc_nand(&eukrea_cpuimx51_nand_board_info);
gpio_request(CPUIMX51_QUARTA_GPIO, "quarta_irq");
gpio_direction_input(CPUIMX51_QUARTA_GPIO);
gpio_free(CPUIMX51_QUARTA_GPIO);
gpio_request(CPUIMX51_QUARTB_GPIO, "quartb_irq");
gpio_direction_input(CPUIMX51_QUARTB_GPIO);
gpio_free(CPUIMX51_QUARTB_GPIO);
gpio_request(CPUIMX51_QUARTC_GPIO, "quartc_irq");
gpio_direction_input(CPUIMX51_QUARTC_GPIO);
gpio_free(CPUIMX51_QUARTC_GPIO);
gpio_request(CPUIMX51_QUARTD_GPIO, "quartd_irq");
gpio_direction_input(CPUIMX51_QUARTD_GPIO);
gpio_free(CPUIMX51_QUARTD_GPIO);
imx51_add_fec(NULL);
platform_add_devices(devices, ARRAY_SIZE(devices));
imx51_add_imx_i2c(1, &eukrea_cpuimx51_i2c_data);
i2c_register_board_info(1, eukrea_cpuimx51_i2c_devices,
ARRAY_SIZE(eukrea_cpuimx51_i2c_devices));
if (otg_mode_host)
imx51_add_mxc_ehci_otg(&dr_utmi_config);
else {
initialize_otg_port(NULL);
imx51_add_fsl_usb2_udc(&usb_pdata);
}
imx51_add_mxc_ehci_hs(1, &usbh1_config);
#ifdef CONFIG_MACH_EUKREA_MBIMX51_BASEBOARD
eukrea_mbimx51_baseboard_init();
#endif
}
static void __init eukrea_cpuimx51_timer_init(void)
{
mx51_clocks_init(32768, 24000000, 22579200, 0);
}
static struct sys_timer mxc_timer = {
.init = eukrea_cpuimx51_timer_init,
};
MACHINE_START(EUKREA_CPUIMX51, "Eukrea CPUIMX51 Module")
/* Maintainer: Eric Bénard <eric@eukrea.com> */
.atag_offset = 0x100,
.map_io = mx51_map_io,
.init_early = imx51_init_early,
.init_irq = mx51_init_irq,
.handle_irq = imx51_handle_irq,
.timer = &mxc_timer,
.init_machine = eukrea_cpuimx51_init,
.restart = mxc_restart,
MACHINE_END
......@@ -41,11 +41,13 @@
#define USBH1_RST IMX_GPIO_NR(2, 28)
#define ETH_RST IMX_GPIO_NR(2, 31)
#define TSC2007_IRQGPIO IMX_GPIO_NR(3, 12)
#define TSC2007_IRQGPIO_REV2 IMX_GPIO_NR(3, 12)
#define TSC2007_IRQGPIO_REV3 IMX_GPIO_NR(4, 0)
#define CAN_IRQGPIO IMX_GPIO_NR(1, 1)
#define CAN_RST IMX_GPIO_NR(4, 15)
#define CAN_NCS IMX_GPIO_NR(4, 24)
#define CAN_RXOBF IMX_GPIO_NR(1, 4)
#define CAN_RXOBF_REV2 IMX_GPIO_NR(1, 4)
#define CAN_RXOBF_REV3 IMX_GPIO_NR(3, 12)
#define CAN_RX1BF IMX_GPIO_NR(1, 6)
#define CAN_TXORTS IMX_GPIO_NR(1, 7)
#define CAN_TX1RTS IMX_GPIO_NR(1, 8)
......@@ -90,6 +92,10 @@ static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
MX51_PAD_I2C1_CLK__GPIO4_16,
MX51_PAD_I2C1_DAT__GPIO4_17,
/* I2C1 */
MX51_PAD_SD2_CMD__I2C1_SCL,
MX51_PAD_SD2_CLK__I2C1_SDA,
/* CAN */
MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI,
MX51_PAD_CSPI1_MISO__ECSPI1_MISO,
......@@ -108,15 +114,27 @@ static iomux_v3_cfg_t eukrea_cpuimx51sd_pads[] = {
NEW_PAD_CTRL(MX51_PAD_GPIO_NAND__GPIO_NAND, PAD_CTL_PUS_22K_UP |
PAD_CTL_PKE | PAD_CTL_SRE_FAST |
PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
NEW_PAD_CTRL(MX51_PAD_NANDF_D8__GPIO4_0, PAD_CTL_PUS_22K_UP |
PAD_CTL_PKE | PAD_CTL_SRE_FAST |
PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
};
static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS,
};
static int tsc2007_get_pendown_state(void)
{
if (mx51_revision() < IMX_CHIP_REVISION_3_0)
return !gpio_get_value(TSC2007_IRQGPIO_REV2);
else
return !gpio_get_value(TSC2007_IRQGPIO_REV3);
}
static struct tsc2007_platform_data tsc2007_info = {
.model = 2007,
.x_plate_ohms = 180,
.get_pendown_state = tsc2007_get_pendown_state,
};
static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
......@@ -126,7 +144,6 @@ static struct i2c_board_info eukrea_cpuimx51sd_i2c_devices[] = {
I2C_BOARD_INFO("tsc2007", 0x49),
.type = "tsc2007",
.platform_data = &tsc2007_info,
.irq = IMX_GPIO_TO_IRQ(TSC2007_IRQGPIO),
},
};
......@@ -255,10 +272,14 @@ static const struct spi_imx_master cpuimx51sd_ecspi1_pdata __initconst = {
.num_chipselect = ARRAY_SIZE(cpuimx51sd_spi1_cs),
};
static struct platform_device *platform_devices[] __initdata = {
static struct platform_device *rev2_platform_devices[] __initdata = {
&hsi2c_gpio_device,
};
static const struct imxi2c_platform_data cpuimx51sd_i2c_data __initconst = {
.bitrate = 100000,
};
static void __init eukrea_cpuimx51sd_init(void)
{
imx51_soc_init();
......@@ -272,6 +293,7 @@ static void __init eukrea_cpuimx51sd_init(void)
imx51_add_imx_uart(0, &uart_pdata);
imx51_add_mxc_nand(&eukrea_cpuimx51sd_nand_board_info);
imx51_add_imx2_wdt(0, NULL);
gpio_request(ETH_RST, "eth_rst");
gpio_set_value(ETH_RST, 1);
......@@ -291,13 +313,25 @@ static void __init eukrea_cpuimx51sd_init(void)
spi_register_board_info(cpuimx51sd_spi_device,
ARRAY_SIZE(cpuimx51sd_spi_device));
gpio_request(TSC2007_IRQGPIO, "tsc2007_irq");
gpio_direction_input(TSC2007_IRQGPIO);
gpio_free(TSC2007_IRQGPIO);
if (mx51_revision() < IMX_CHIP_REVISION_3_0) {
eukrea_cpuimx51sd_i2c_devices[1].irq =
gpio_to_irq(TSC2007_IRQGPIO_REV2),
platform_add_devices(rev2_platform_devices,
ARRAY_SIZE(rev2_platform_devices));
gpio_request(TSC2007_IRQGPIO_REV2, "tsc2007_irq");
gpio_direction_input(TSC2007_IRQGPIO_REV2);
gpio_free(TSC2007_IRQGPIO_REV2);
} else {
eukrea_cpuimx51sd_i2c_devices[1].irq =
gpio_to_irq(TSC2007_IRQGPIO_REV3),
imx51_add_imx_i2c(0, &cpuimx51sd_i2c_data);
gpio_request(TSC2007_IRQGPIO_REV3, "tsc2007_irq");
gpio_direction_input(TSC2007_IRQGPIO_REV3);
gpio_free(TSC2007_IRQGPIO_REV3);
}
i2c_register_board_info(0, eukrea_cpuimx51sd_i2c_devices,
ARRAY_SIZE(eukrea_cpuimx51sd_i2c_devices));
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
if (otg_mode_host)
imx51_add_mxc_ehci_otg(&dr_utmi_config);
......
......@@ -106,6 +106,7 @@ static const struct mxc_usbh_platform_data usbh2_pdata __initconst = {
static const struct fsl_usb2_platform_data otg_device_pdata __initconst = {
.operating_mode = FSL_USB2_DR_DEVICE,
.phy_mode = FSL_USB2_PHY_UTMI,
.workaround = FLS_USB2_WORKAROUND_ENGCM09152,
};
static int otg_mode_host;
......@@ -135,6 +136,7 @@ static void __init eukrea_cpuimx25_init(void)
imx25_add_mxc_nand(&eukrea_cpuimx25_nand_board_info);
imx25_add_imxdi_rtc(NULL);
imx25_add_fec(&mx25_fec_pdata);
imx25_add_imx2_wdt(NULL);
i2c_register_board_info(0, eukrea_cpuimx25_i2c_devices,
ARRAY_SIZE(eukrea_cpuimx25_i2c_devices));
......
......@@ -38,6 +38,7 @@
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/system.h>
#include <mach/common.h>
#include <mach/iomux-mx27.h>
......@@ -48,6 +49,14 @@
#define OTG_PHY_CS_GPIO (GPIO_PORTF + 17)
#define SDHC1_IRQ IRQ_GPIOB(25)
#define MOTHERBOARD_BIT2 (GPIO_PORTD + 31)
#define MOTHERBOARD_BIT1 (GPIO_PORTD + 30)
#define MOTHERBOARD_BIT0 (GPIO_PORTD + 29)
#define EXPBOARD_BIT2 (GPIO_PORTD + 25)
#define EXPBOARD_BIT1 (GPIO_PORTD + 27)
#define EXPBOARD_BIT0 (GPIO_PORTD + 28)
static const int visstrim_m10_pins[] __initconst = {
/* UART1 (console) */
PE12_PF_UART1_TXD,
......@@ -119,6 +128,23 @@ static const int visstrim_m10_pins[] __initconst = {
PB19_PF_CSI_D7,
PB20_PF_CSI_VSYNC,
PB21_PF_CSI_HSYNC,
/* mother board version */
MOTHERBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
MOTHERBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
MOTHERBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
/* expansion board version */
EXPBOARD_BIT2 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
EXPBOARD_BIT1 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
EXPBOARD_BIT0 | GPIO_GPIO | GPIO_IN | GPIO_PUEN,
};
static struct gpio visstrim_m10_version_gpios[] = {
{ EXPBOARD_BIT0, GPIOF_IN, "exp-version-0" },
{ EXPBOARD_BIT1, GPIOF_IN, "exp-version-1" },
{ EXPBOARD_BIT2, GPIOF_IN, "exp-version-2" },
{ MOTHERBOARD_BIT0, GPIOF_IN, "mother-version-0" },
{ MOTHERBOARD_BIT1, GPIOF_IN, "mother-version-1" },
{ MOTHERBOARD_BIT2, GPIOF_IN, "mother-version-2" },
};
/* Camera */
......@@ -369,11 +395,40 @@ static const struct imx_ssi_platform_data visstrim_m10_ssi_pdata __initconst = {
.flags = IMX_SSI_DMA | IMX_SSI_SYN,
};
static void __init visstrim_m10_revision(void)
{
int exp_version = 0;
int mo_version = 0;
int ret;
ret = gpio_request_array(visstrim_m10_version_gpios,
ARRAY_SIZE(visstrim_m10_version_gpios));
if (ret) {
pr_err("Failed to request version gpios");
return;
}
/* Get expansion board version (negative logic) */
exp_version |= !gpio_get_value(EXPBOARD_BIT2) << 2;
exp_version |= !gpio_get_value(EXPBOARD_BIT1) << 1;
exp_version |= !gpio_get_value(EXPBOARD_BIT0);
/* Get mother board version (negative logic) */
mo_version |= !gpio_get_value(MOTHERBOARD_BIT2) << 2;
mo_version |= !gpio_get_value(MOTHERBOARD_BIT1) << 1;
mo_version |= !gpio_get_value(MOTHERBOARD_BIT0);
system_rev = 0x27000;
system_rev |= (mo_version << 4);
system_rev |= exp_version;
}
static void __init visstrim_m10_board_init(void)
{
int ret;
imx27_soc_init();
visstrim_m10_revision();
ret = mxc_gpio_setup_multiple_pins(visstrim_m10_pins,
ARRAY_SIZE(visstrim_m10_pins), "VISSTRIM_M10");
......
......@@ -34,6 +34,8 @@
#include <linux/usb/otg.h>
#include <linux/mtd/physmap.h>
#include <linux/mfd/mc13892.h>
#include <linux/regulator/machine.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
......@@ -253,6 +255,8 @@ static iomux_v3_cfg_t mx35pdk_pads[] = {
MX35_PAD_CSI_MCLK__IPU_CSI_MCLK,
MX35_PAD_CSI_PIXCLK__IPU_CSI_PIXCLK,
MX35_PAD_CSI_VSYNC__IPU_CSI_VSYNC,
/*PMIC IRQ*/
MX35_PAD_GPIO2_0__GPIO2_0,
};
/*
......@@ -317,6 +321,193 @@ static struct platform_device mx35_3ds_ov2640 = {
},
};
static struct regulator_consumer_supply sw1_consumers[] = {
{
.supply = "cpu_vcc",
}
};
static struct regulator_consumer_supply vcam_consumers[] = {
/* sgtl5000 */
REGULATOR_SUPPLY("VDDA", "0-000a"),
};
static struct regulator_consumer_supply vaudio_consumers[] = {
REGULATOR_SUPPLY("cmos_vio", "soc-camera-pdrv.0"),
};
static struct regulator_init_data sw1_init = {
.constraints = {
.name = "SW1",
.min_uV = 600000,
.max_uV = 1375000,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
.valid_modes_mask = 0,
.always_on = 1,
.boot_on = 1,
},
.num_consumer_supplies = ARRAY_SIZE(sw1_consumers),
.consumer_supplies = sw1_consumers,
};
static struct regulator_init_data sw2_init = {
.constraints = {
.name = "SW2",
.always_on = 1,
.boot_on = 1,
}
};
static struct regulator_init_data sw3_init = {
.constraints = {
.name = "SW3",
.always_on = 1,
.boot_on = 1,
}
};
static struct regulator_init_data sw4_init = {
.constraints = {
.name = "SW4",
.always_on = 1,
.boot_on = 1,
}
};
static struct regulator_init_data viohi_init = {
.constraints = {
.name = "VIOHI",
.boot_on = 1,
}
};
static struct regulator_init_data vusb_init = {
.constraints = {
.name = "VUSB",
.boot_on = 1,
}
};
static struct regulator_init_data vdig_init = {
.constraints = {
.name = "VDIG",
.boot_on = 1,
}
};
static struct regulator_init_data vpll_init = {
.constraints = {
.name = "VPLL",
.boot_on = 1,
}
};
static struct regulator_init_data vusb2_init = {
.constraints = {
.name = "VUSB2",
.boot_on = 1,
}
};
static struct regulator_init_data vvideo_init = {
.constraints = {
.name = "VVIDEO",
.boot_on = 1
}
};
static struct regulator_init_data vaudio_init = {
.constraints = {
.name = "VAUDIO",
.min_uV = 2300000,
.max_uV = 3000000,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
.boot_on = 1
},
.num_consumer_supplies = ARRAY_SIZE(vaudio_consumers),
.consumer_supplies = vaudio_consumers,
};
static struct regulator_init_data vcam_init = {
.constraints = {
.name = "VCAM",
.min_uV = 2500000,
.max_uV = 3000000,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
REGULATOR_CHANGE_MODE,
.valid_modes_mask = REGULATOR_MODE_FAST | REGULATOR_MODE_NORMAL,
.boot_on = 1
},
.num_consumer_supplies = ARRAY_SIZE(vcam_consumers),
.consumer_supplies = vcam_consumers,
};
static struct regulator_init_data vgen1_init = {
.constraints = {
.name = "VGEN1",
}
};
static struct regulator_init_data vgen2_init = {
.constraints = {
.name = "VGEN2",
.boot_on = 1,
}
};
static struct regulator_init_data vgen3_init = {
.constraints = {
.name = "VGEN3",
}
};
static struct mc13xxx_regulator_init_data mx35_3ds_regulators[] = {
{ .id = MC13892_SW1, .init_data = &sw1_init },
{ .id = MC13892_SW2, .init_data = &sw2_init },
{ .id = MC13892_SW3, .init_data = &sw3_init },
{ .id = MC13892_SW4, .init_data = &sw4_init },
{ .id = MC13892_VIOHI, .init_data = &viohi_init },
{ .id = MC13892_VPLL, .init_data = &vpll_init },
{ .id = MC13892_VDIG, .init_data = &vdig_init },
{ .id = MC13892_VUSB2, .init_data = &vusb2_init },
{ .id = MC13892_VVIDEO, .init_data = &vvideo_init },
{ .id = MC13892_VAUDIO, .init_data = &vaudio_init },
{ .id = MC13892_VCAM, .init_data = &vcam_init },
{ .id = MC13892_VGEN1, .init_data = &vgen1_init },
{ .id = MC13892_VGEN2, .init_data = &vgen2_init },
{ .id = MC13892_VGEN3, .init_data = &vgen3_init },
{ .id = MC13892_VUSB, .init_data = &vusb_init },
};
static struct mc13xxx_platform_data mx35_3ds_mc13892_data = {
.flags = MC13XXX_USE_RTC | MC13XXX_USE_TOUCHSCREEN,
.regulators = {
.num_regulators = ARRAY_SIZE(mx35_3ds_regulators),
.regulators = mx35_3ds_regulators,
},
};
#define GPIO_PMIC_INT IMX_GPIO_NR(2, 0)
static struct i2c_board_info mx35_3ds_i2c_mc13892 = {
I2C_BOARD_INFO("mc13892", 0x08),
.platform_data = &mx35_3ds_mc13892_data,
.irq = IMX_GPIO_TO_IRQ(GPIO_PMIC_INT),
};
static void __init imx35_3ds_init_mc13892(void)
{
int ret = gpio_request_one(GPIO_PMIC_INT, GPIOF_DIR_IN, "pmic irq");
if (ret) {
pr_err("failed to get pmic irq: %d\n", ret);
return;
}
i2c_register_board_info(0, &mx35_3ds_i2c_mc13892, 1);
}
static int mx35_3ds_otg_init(struct platform_device *pdev)
{
return mx35_initialize_usb_hw(pdev->id, MXC_EHCI_INTERNAL_PHY);
......@@ -412,6 +603,8 @@ static void __init mx35_3ds_init(void)
imx35_fb_pdev = imx35_add_mx3_sdc_fb(&mx3fb_pdata);
mx35_3ds_lcd.dev.parent = &imx35_fb_pdev->dev;
platform_device_register(&mx35_3ds_lcd);
imx35_3ds_init_mc13892();
}
static void __init mx35pdk_timer_init(void)
......
......@@ -58,6 +58,28 @@ config MACH_DREAMPLUG_DT
Say 'Y' here if you want your kernel to support the
Marvell DreamPlug (Flattened Device Tree).
config MACH_ICONNECT_DT
bool "Iomega Iconnect (Flattened Device Tree)"
select ARCH_KIRKWOOD_DT
help
Say 'Y' here to enable Iomega Iconnect support.
config MACH_DLINK_KIRKWOOD_DT
bool "D-Link Kirkwood-based NAS (Flattened Device Tree)"
select ARCH_KIRKWOOD_DT
help
Say 'Y' here if you want your kernel to support the
Kirkwood-based D-Link NASes such as DNS-320 & DNS-325,
using Flattened Device Tree.
config MACH_IB62X0_DT
bool "RaidSonic IB-NAS6210, IB-NAS6220 (Flattened Device Tree)"
select ARCH_KIRKWOOD_DT
help
Say 'Y' here if you want your kernel to support the
RaidSonic IB-NAS6210 & IB-NAS6220 devices, using
Flattened Device Tree.
config MACH_TS219
bool "QNAP TS-110, TS-119, TS-119P+, TS-210, TS-219, TS-219P and TS-219P+ Turbo NAS"
help
......
......@@ -22,3 +22,6 @@ obj-$(CONFIG_MACH_T5325) += t5325-setup.o
obj-$(CONFIG_CPU_IDLE) += cpuidle.o
obj-$(CONFIG_ARCH_KIRKWOOD_DT) += board-dt.o
obj-$(CONFIG_MACH_DREAMPLUG_DT) += board-dreamplug.o
obj-$(CONFIG_MACH_ICONNECT_DT) += board-iconnect.o
obj-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += board-dnskw.o
obj-$(CONFIG_MACH_IB62X0_DT) += board-ib62x0.o
......@@ -3,3 +3,7 @@ params_phys-y := 0x00000100
initrd_phys-y := 0x00800000
dtb-$(CONFIG_MACH_DREAMPLUG_DT) += kirkwood-dreamplug.dtb
dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns320.dtb
dtb-$(CONFIG_MACH_DLINK_KIRKWOOD_DT) += kirkwood-dns325.dtb
dtb-$(CONFIG_MACH_ICONNECT_DT) += kirkwood-iconnect.dtb
dtb-$(CONFIG_MACH_IB62X0_DT) += kirkwood-ib62x0.dtb
/*
* Copyright 2012 (C), Jamie Lentin <jm@lentin.co.uk>
*
* arch/arm/mach-kirkwood/board-dnskw.c
*
* D-link DNS-320 & DNS-325 NAS Init for drivers not converted to
* flattened device tree yet.
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/ata_platform.h>
#include <linux/mv643xx_eth.h>
#include <linux/of.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/gpio-fan.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <mach/kirkwood.h>
#include <mach/bridge-regs.h>
#include "common.h"
#include "mpp.h"
static struct mv643xx_eth_platform_data dnskw_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
};
static struct mv_sata_platform_data dnskw_sata_data = {
.n_ports = 2,
};
static unsigned int dnskw_mpp_config[] __initdata = {
MPP13_UART1_TXD, /* Custom ... */
MPP14_UART1_RXD, /* ... Controller (DNS-320 only) */
MPP20_SATA1_ACTn, /* LED: White Right HDD */
MPP21_SATA0_ACTn, /* LED: White Left HDD */
MPP24_GPIO,
MPP25_GPIO,
MPP26_GPIO, /* LED: Power */
MPP27_GPIO, /* LED: Red Right HDD */
MPP28_GPIO, /* LED: Red Left HDD */
MPP29_GPIO, /* LED: Red USB (DNS-325 only) */
MPP30_GPIO,
MPP31_GPIO,
MPP32_GPIO,
MPP33_GPO,
MPP34_GPIO, /* Button: Front power */
MPP35_GPIO, /* LED: Red USB (DNS-320 only) */
MPP36_GPIO, /* Power: Turn off board */
MPP37_GPIO, /* Power: Turn back on after power failure */
MPP38_GPIO,
MPP39_GPIO, /* Power: SATA0 */
MPP40_GPIO, /* Power: SATA1 */
MPP41_GPIO, /* SATA0 present */
MPP42_GPIO, /* SATA1 present */
MPP43_GPIO, /* LED: White USB */
MPP44_GPIO, /* Fan: Tachometer Pin */
MPP45_GPIO, /* Fan: high speed */
MPP46_GPIO, /* Fan: low speed */
MPP47_GPIO, /* Button: Back unmount */
MPP48_GPIO, /* Button: Back reset */
MPP49_GPIO, /* Temp Alarm (DNS-325) Pin of U5 (DNS-320) */
0
};
static struct gpio_led dns325_led_pins[] = {
{
.name = "dns325:white:power",
.gpio = 26,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "dns325:white:usb",
.gpio = 43,
.active_low = 1,
},
{
.name = "dns325:red:l_hdd",
.gpio = 28,
.active_low = 1,
},
{
.name = "dns325:red:r_hdd",
.gpio = 27,
.active_low = 1,
},
{
.name = "dns325:red:usb",
.gpio = 29,
.active_low = 1,
},
};
static struct gpio_led_platform_data dns325_led_data = {
.num_leds = ARRAY_SIZE(dns325_led_pins),
.leds = dns325_led_pins,
};
static struct platform_device dns325_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &dns325_led_data,
},
};
static struct gpio_led dns320_led_pins[] = {
{
.name = "dns320:blue:power",
.gpio = 26,
.active_low = 1,
.default_trigger = "default-on",
},
{
.name = "dns320:blue:usb",
.gpio = 43,
.active_low = 1,
},
{
.name = "dns320:orange:l_hdd",
.gpio = 28,
.active_low = 1,
},
{
.name = "dns320:orange:r_hdd",
.gpio = 27,
.active_low = 1,
},
{
.name = "dns320:orange:usb",
.gpio = 35,
.active_low = 1,
},
};
static struct gpio_led_platform_data dns320_led_data = {
.num_leds = ARRAY_SIZE(dns320_led_pins),
.leds = dns320_led_pins,
};
static struct platform_device dns320_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &dns320_led_data,
},
};
static struct i2c_board_info dns325_i2c_board_info[] __initdata = {
{
I2C_BOARD_INFO("lm75", 0x48),
},
/* Something at 0x0c also */
};
static struct gpio_keys_button dnskw_button_pins[] = {
{
.code = KEY_POWER,
.gpio = 34,
.desc = "Power button",
.active_low = 1,
},
{
.code = KEY_EJECTCD,
.gpio = 47,
.desc = "USB unmount button",
.active_low = 1,
},
{
.code = KEY_RESTART,
.gpio = 48,
.desc = "Reset button",
.active_low = 1,
},
};
static struct gpio_keys_platform_data dnskw_button_data = {
.buttons = dnskw_button_pins,
.nbuttons = ARRAY_SIZE(dnskw_button_pins),
};
static struct platform_device dnskw_button_device = {
.name = "gpio-keys",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &dnskw_button_data,
}
};
/* Fan: ADDA AD045HB-G73 40mm 6000rpm@5v */
static struct gpio_fan_speed dnskw_fan_speed[] = {
{ 0, 0 },
{ 3000, 1 },
{ 6000, 2 },
};
static unsigned dnskw_fan_pins[] = {46, 45};
static struct gpio_fan_platform_data dnskw_fan_data = {
.num_ctrl = ARRAY_SIZE(dnskw_fan_pins),
.ctrl = dnskw_fan_pins,
.num_speed = ARRAY_SIZE(dnskw_fan_speed),
.speed = dnskw_fan_speed,
};
static struct platform_device dnskw_fan_device = {
.name = "gpio-fan",
.id = -1,
.dev = {
.platform_data = &dnskw_fan_data,
},
};
static void dnskw_power_off(void)
{
gpio_set_value(36, 1);
}
/* Register any GPIO for output and set the value */
static void __init dnskw_gpio_register(unsigned gpio, char *name, int def)
{
if (gpio_request(gpio, name) == 0 &&
gpio_direction_output(gpio, 0) == 0) {
gpio_set_value(gpio, def);
if (gpio_export(gpio, 0) != 0)
pr_err("dnskw: Failed to export GPIO %s\n", name);
} else
pr_err("dnskw: Failed to register %s\n", name);
}
void __init dnskw_init(void)
{
kirkwood_mpp_conf(dnskw_mpp_config);
kirkwood_ehci_init();
kirkwood_ge00_init(&dnskw_ge00_data);
kirkwood_sata_init(&dnskw_sata_data);
kirkwood_i2c_init();
platform_device_register(&dnskw_button_device);
platform_device_register(&dnskw_fan_device);
if (of_machine_is_compatible("dlink,dns-325")) {
i2c_register_board_info(0, dns325_i2c_board_info,
ARRAY_SIZE(dns325_i2c_board_info));
platform_device_register(&dns325_led_device);
} else if (of_machine_is_compatible("dlink,dns-320"))
platform_device_register(&dns320_led_device);
/* Register power-off GPIO. */
if (gpio_request(36, "dnskw:power:off") == 0
&& gpio_direction_output(36, 0) == 0)
pm_power_off = dnskw_power_off;
else
pr_err("dnskw: failed to configure power-off GPIO\n");
/* Ensure power is supplied to both HDDs */
dnskw_gpio_register(39, "dnskw:power:sata0", 1);
dnskw_gpio_register(40, "dnskw:power:sata1", 1);
/* Set NAS to turn back on after a power failure */
dnskw_gpio_register(37, "dnskw:power:recover", 1);
}
......@@ -56,11 +56,24 @@ static void __init kirkwood_dt_init(void)
if (of_machine_is_compatible("globalscale,dreamplug"))
dreamplug_init();
if (of_machine_is_compatible("dlink,dns-kirkwood"))
dnskw_init();
if (of_machine_is_compatible("iom,iconnect"))
iconnect_init();
if (of_machine_is_compatible("raidsonic,ib-nas62x0"))
ib62x0_init();
of_platform_populate(NULL, kirkwood_dt_match_table, NULL, NULL);
}
static const char *kirkwood_dt_board_compat[] = {
"globalscale,dreamplug",
"dlink,dns-320",
"dlink,dns-325",
"iom,iconnect",
"raidsonic,ib-nas62x0",
NULL
};
......
/*
* Copyright 2012 (C), Simon Baatz <gmbnomis@gmail.com>
*
* arch/arm/mach-kirkwood/board-ib62x0.c
*
* RaidSonic ICY BOX IB-NAS6210 & IB-NAS6220 init for drivers not
* converted to flattened device tree yet.
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mtd/partitions.h>
#include <linux/ata_platform.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/leds.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
#include "common.h"
#include "mpp.h"
#define IB62X0_GPIO_POWER_OFF 24
static struct mv643xx_eth_platform_data ib62x0_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(8),
};
static struct mv_sata_platform_data ib62x0_sata_data = {
.n_ports = 2,
};
static unsigned int ib62x0_mpp_config[] __initdata = {
MPP0_NF_IO2,
MPP1_NF_IO3,
MPP2_NF_IO4,
MPP3_NF_IO5,
MPP4_NF_IO6,
MPP5_NF_IO7,
MPP18_NF_IO0,
MPP19_NF_IO1,
MPP22_GPIO, /* OS LED red */
MPP24_GPIO, /* Power off device */
MPP25_GPIO, /* OS LED green */
MPP27_GPIO, /* USB transfer LED */
MPP28_GPIO, /* Reset button */
MPP29_GPIO, /* USB Copy button */
0
};
static struct gpio_led ib62x0_led_pins[] = {
{
.name = "ib62x0:green:os",
.default_trigger = "default-on",
.gpio = 25,
.active_low = 0,
},
{
.name = "ib62x0:red:os",
.default_trigger = "none",
.gpio = 22,
.active_low = 0,
},
{
.name = "ib62x0:red:usb_copy",
.default_trigger = "none",
.gpio = 27,
.active_low = 0,
},
};
static struct gpio_led_platform_data ib62x0_led_data = {
.leds = ib62x0_led_pins,
.num_leds = ARRAY_SIZE(ib62x0_led_pins),
};
static struct platform_device ib62x0_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &ib62x0_led_data,
}
};
static struct gpio_keys_button ib62x0_button_pins[] = {
{
.code = KEY_COPY,
.gpio = 29,
.desc = "USB Copy",
.active_low = 1,
},
{
.code = KEY_RESTART,
.gpio = 28,
.desc = "Reset",
.active_low = 1,
},
};
static struct gpio_keys_platform_data ib62x0_button_data = {
.buttons = ib62x0_button_pins,
.nbuttons = ARRAY_SIZE(ib62x0_button_pins),
};
static struct platform_device ib62x0_button_device = {
.name = "gpio-keys",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &ib62x0_button_data,
}
};
static void ib62x0_power_off(void)
{
gpio_set_value(IB62X0_GPIO_POWER_OFF, 1);
}
void __init ib62x0_init(void)
{
/*
* Basic setup. Needs to be called early.
*/
kirkwood_mpp_conf(ib62x0_mpp_config);
kirkwood_ehci_init();
kirkwood_ge00_init(&ib62x0_ge00_data);
kirkwood_sata_init(&ib62x0_sata_data);
platform_device_register(&ib62x0_led_device);
platform_device_register(&ib62x0_button_device);
if (gpio_request(IB62X0_GPIO_POWER_OFF, "ib62x0:power:off") == 0 &&
gpio_direction_output(IB62X0_GPIO_POWER_OFF, 0) == 0)
pm_power_off = ib62x0_power_off;
else
pr_err("board-ib62x0: failed to configure power-off GPIO\n");
}
/*
* arch/arm/mach-kirkwood/board-iconnect.c
*
* Iomega i-connect Board Setup
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <linux/of_fdt.h>
#include <linux/of_irq.h>
#include <linux/of_platform.h>
#include <linux/mtd/partitions.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio.h>
#include <linux/leds.h>
#include <linux/spi/flash.h>
#include <linux/spi/spi.h>
#include <linux/spi/orion_spi.h>
#include <linux/i2c.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <asm/mach/arch.h>
#include <mach/kirkwood.h>
#include "common.h"
#include "mpp.h"
static struct mv643xx_eth_platform_data iconnect_ge00_data = {
.phy_addr = MV643XX_ETH_PHY_ADDR(11),
};
static struct gpio_led iconnect_led_pins[] = {
{
.name = "led_level",
.gpio = 41,
.default_trigger = "default-on",
}, {
.name = "power:blue",
.gpio = 42,
.default_trigger = "timer",
}, {
.name = "power:red",
.gpio = 43,
}, {
.name = "usb1:blue",
.gpio = 44,
}, {
.name = "usb2:blue",
.gpio = 45,
}, {
.name = "usb3:blue",
.gpio = 46,
}, {
.name = "usb4:blue",
.gpio = 47,
}, {
.name = "otb:blue",
.gpio = 48,
},
};
static struct gpio_led_platform_data iconnect_led_data = {
.leds = iconnect_led_pins,
.num_leds = ARRAY_SIZE(iconnect_led_pins),
.gpio_blink_set = orion_gpio_led_blink_set,
};
static struct platform_device iconnect_leds = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &iconnect_led_data,
}
};
static unsigned int iconnect_mpp_config[] __initdata = {
MPP12_GPIO,
MPP35_GPIO,
MPP41_GPIO,
MPP42_GPIO,
MPP43_GPIO,
MPP44_GPIO,
MPP45_GPIO,
MPP46_GPIO,
MPP47_GPIO,
MPP48_GPIO,
0
};
static struct i2c_board_info __initdata iconnect_board_info[] = {
{
I2C_BOARD_INFO("lm63", 0x4c),
},
};
static struct mtd_partition iconnect_nand_parts[] = {
{
.name = "flash",
.offset = 0,
.size = MTDPART_SIZ_FULL,
},
};
/* yikes... theses are the original input buttons */
/* but I'm not convinced by the sw event choices */
static struct gpio_keys_button iconnect_buttons[] = {
{
.type = EV_SW,
.code = SW_LID,
.gpio = 12,
.desc = "Reset Button",
.active_low = 1,
.debounce_interval = 100,
}, {
.type = EV_SW,
.code = SW_TABLET_MODE,
.gpio = 35,
.desc = "OTB Button",
.active_low = 1,
.debounce_interval = 100,
},
};
static struct gpio_keys_platform_data iconnect_button_data = {
.buttons = iconnect_buttons,
.nbuttons = ARRAY_SIZE(iconnect_buttons),
};
static struct platform_device iconnect_button_device = {
.name = "gpio-keys",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &iconnect_button_data,
},
};
void __init iconnect_init(void)
{
kirkwood_mpp_conf(iconnect_mpp_config);
kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25);
kirkwood_i2c_init();
i2c_register_board_info(0, iconnect_board_info,
ARRAY_SIZE(iconnect_board_info));
kirkwood_ehci_init();
kirkwood_ge00_init(&iconnect_ge00_data);
platform_device_register(&iconnect_button_device);
platform_device_register(&iconnect_leds);
}
static int __init iconnect_pci_init(void)
{
if (of_machine_is_compatible("iom,iconnect"))
kirkwood_pcie_init(KW_PCIE0);
return 0;
}
subsys_initcall(iconnect_pci_init);
......@@ -15,6 +15,7 @@
#include <linux/ata_platform.h>
#include <linux/mtd/nand.h>
#include <linux/dma-mapping.h>
#include <linux/of.h>
#include <net/dsa.h>
#include <asm/page.h>
#include <asm/timex.h>
......@@ -482,6 +483,9 @@ static int __init kirkwood_clock_gate(void)
unsigned int curr = readl(CLOCK_GATING_CTRL);
u32 dev, rev;
#ifdef CONFIG_OF
struct device_node *np;
#endif
kirkwood_pcie_id(&dev, &rev);
printk(KERN_DEBUG "Gating clock of unused units\n");
printk(KERN_DEBUG "before: 0x%08x\n", curr);
......@@ -489,6 +493,14 @@ static int __init kirkwood_clock_gate(void)
/* Make sure those units are accessible */
writel(curr | CGC_SATA0 | CGC_SATA1 | CGC_PEX0 | CGC_PEX1, CLOCK_GATING_CTRL);
#ifdef CONFIG_OF
np = of_find_compatible_node(NULL, NULL, "mrvl,orion-nand");
if (np && of_device_is_available(np)) {
kirkwood_clk_ctrl |= CGC_RUNIT;
of_node_put(np);
}
#endif
/* For SATA: first shutdown the phy */
if (!(kirkwood_clk_ctrl & CGC_SATA0)) {
/* Disable PLL and IVREF */
......
......@@ -58,6 +58,24 @@ void dreamplug_init(void);
static inline void dreamplug_init(void) {};
#endif
#ifdef CONFIG_MACH_DLINK_KIRKWOOD_DT
void dnskw_init(void);
#else
static inline void dnskw_init(void) {};
#endif
#ifdef CONFIG_MACH_ICONNECT_DT
void iconnect_init(void);
#else
static inline void iconnect_init(void) {};
#endif
#ifdef CONFIG_MACH_IB62X0_DT
void ib62x0_init(void);
#else
static inline void ib62x0_init(void) {};
#endif
/* early init functions not converted to fdt yet */
char *kirkwood_id(void);
void kirkwood_l2_init(void);
......
......@@ -122,4 +122,11 @@ config CPU_MMP2
select CPU_PJ4
help
Select code specific to MMP2. MMP2 is ARMv7 compatible.
config USB_EHCI_MV_U2O
bool "EHCI support for PXA USB OTG controller"
depends on USB_EHCI_MV
help
Enables support for OTG controller which can be switched to host mode.
endif
......@@ -17,6 +17,7 @@
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/interrupt.h>
#include <linux/platform_data/mv_usb.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
......@@ -221,6 +222,21 @@ static struct pxa27x_keypad_platform_data aspenite_keypad_info __initdata = {
.debounce_interval = 30,
};
#if defined(CONFIG_USB_EHCI_MV)
static char *pxa168_sph_clock_name[] = {
[0] = "PXA168-USBCLK",
};
static struct mv_usb_platform_data pxa168_sph_pdata = {
.clknum = 1,
.clkname = pxa168_sph_clock_name,
.mode = MV_USB_MODE_HOST,
.phy_init = pxa_usb_phy_init,
.phy_deinit = pxa_usb_phy_deinit,
.set_vbus = NULL,
};
#endif
static void __init common_init(void)
{
mfp_config(ARRAY_AND_SIZE(common_pin_config));
......@@ -236,6 +252,10 @@ static void __init common_init(void)
/* off-chip devices */
platform_device_register(&smc91x_device);
#if defined(CONFIG_USB_EHCI_MV)
pxa168_add_usb_host(&pxa168_sph_pdata);
#endif
}
MACHINE_START(ASPENITE, "PXA168-based Aspenite Development Platform")
......
......@@ -9,9 +9,13 @@
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/delay.h>
#include <asm/irq.h>
#include <mach/irqs.h>
#include <mach/devices.h>
#include <mach/cputype.h>
#include <mach/regs-usb.h>
int __init pxa_register_device(struct pxa_device_desc *desc,
void *data, size_t size)
......@@ -67,3 +71,281 @@ int __init pxa_register_device(struct pxa_device_desc *desc,
return platform_device_add(pdev);
}
#if defined(CONFIG_USB) || defined(CONFIG_USB_GADGET)
/*****************************************************************************
* The registers read/write routines
*****************************************************************************/
static unsigned int u2o_get(void __iomem *base, unsigned int offset)
{
return readl_relaxed(base + offset);
}
static void u2o_set(void __iomem *base, unsigned int offset,
unsigned int value)
{
u32 reg;
reg = readl_relaxed(base + offset);
reg |= value;
writel_relaxed(reg, base + offset);
readl_relaxed(base + offset);
}
static void u2o_clear(void __iomem *base, unsigned int offset,
unsigned int value)
{
u32 reg;
reg = readl_relaxed(base + offset);
reg &= ~value;
writel_relaxed(reg, base + offset);
readl_relaxed(base + offset);
}
static void u2o_write(void __iomem *base, unsigned int offset,
unsigned int value)
{
writel_relaxed(value, base + offset);
readl_relaxed(base + offset);
}
#if defined(CONFIG_USB_MV_UDC) || defined(CONFIG_USB_EHCI_MV)
#if defined(CONFIG_CPU_PXA910) || defined(CONFIG_CPU_PXA168)
static DEFINE_MUTEX(phy_lock);
static int phy_init_cnt;
static int usb_phy_init_internal(void __iomem *base)
{
int loops;
pr_info("Init usb phy!!!\n");
/* Initialize the USB PHY power */
if (cpu_is_pxa910()) {
u2o_set(base, UTMI_CTRL, (1<<UTMI_CTRL_INPKT_DELAY_SOF_SHIFT)
| (1<<UTMI_CTRL_PU_REF_SHIFT));
}
u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
u2o_set(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
/* UTMI_PLL settings */
u2o_clear(base, UTMI_PLL, UTMI_PLL_PLLVDD18_MASK
| UTMI_PLL_PLLVDD12_MASK | UTMI_PLL_PLLCALI12_MASK
| UTMI_PLL_FBDIV_MASK | UTMI_PLL_REFDIV_MASK
| UTMI_PLL_ICP_MASK | UTMI_PLL_KVCO_MASK);
u2o_set(base, UTMI_PLL, 0xee<<UTMI_PLL_FBDIV_SHIFT
| 0xb<<UTMI_PLL_REFDIV_SHIFT | 3<<UTMI_PLL_PLLVDD18_SHIFT
| 3<<UTMI_PLL_PLLVDD12_SHIFT | 3<<UTMI_PLL_PLLCALI12_SHIFT
| 1<<UTMI_PLL_ICP_SHIFT | 3<<UTMI_PLL_KVCO_SHIFT);
/* UTMI_TX */
u2o_clear(base, UTMI_TX, UTMI_TX_REG_EXT_FS_RCAL_EN_MASK
| UTMI_TX_TXVDD12_MASK | UTMI_TX_CK60_PHSEL_MASK
| UTMI_TX_IMPCAL_VTH_MASK | UTMI_TX_REG_EXT_FS_RCAL_MASK
| UTMI_TX_AMP_MASK);
u2o_set(base, UTMI_TX, 3<<UTMI_TX_TXVDD12_SHIFT
| 4<<UTMI_TX_CK60_PHSEL_SHIFT | 4<<UTMI_TX_IMPCAL_VTH_SHIFT
| 8<<UTMI_TX_REG_EXT_FS_RCAL_SHIFT | 3<<UTMI_TX_AMP_SHIFT);
/* UTMI_RX */
u2o_clear(base, UTMI_RX, UTMI_RX_SQ_THRESH_MASK
| UTMI_REG_SQ_LENGTH_MASK);
u2o_set(base, UTMI_RX, 7<<UTMI_RX_SQ_THRESH_SHIFT
| 2<<UTMI_REG_SQ_LENGTH_SHIFT);
/* UTMI_IVREF */
if (cpu_is_pxa168())
/* fixing Microsoft Altair board interface with NEC hub issue -
* Set UTMI_IVREF from 0x4a3 to 0x4bf */
u2o_write(base, UTMI_IVREF, 0x4bf);
/* toggle VCOCAL_START bit of UTMI_PLL */
udelay(200);
u2o_set(base, UTMI_PLL, VCOCAL_START);
udelay(40);
u2o_clear(base, UTMI_PLL, VCOCAL_START);
/* toggle REG_RCAL_START bit of UTMI_TX */
udelay(400);
u2o_set(base, UTMI_TX, REG_RCAL_START);
udelay(40);
u2o_clear(base, UTMI_TX, REG_RCAL_START);
udelay(400);
/* Make sure PHY PLL is ready */
loops = 0;
while ((u2o_get(base, UTMI_PLL) & PLL_READY) == 0) {
mdelay(1);
loops++;
if (loops > 100) {
printk(KERN_WARNING "calibrate timeout, UTMI_PLL %x\n",
u2o_get(base, UTMI_PLL));
break;
}
}
if (cpu_is_pxa168()) {
u2o_set(base, UTMI_RESERVE, 1 << 5);
/* Turn on UTMI PHY OTG extension */
u2o_write(base, UTMI_OTG_ADDON, 1);
}
return 0;
}
static int usb_phy_deinit_internal(void __iomem *base)
{
pr_info("Deinit usb phy!!!\n");
if (cpu_is_pxa168())
u2o_clear(base, UTMI_OTG_ADDON, UTMI_OTG_ADDON_OTG_ON);
u2o_clear(base, UTMI_CTRL, UTMI_CTRL_RXBUF_PDWN);
u2o_clear(base, UTMI_CTRL, UTMI_CTRL_TXBUF_PDWN);
u2o_clear(base, UTMI_CTRL, UTMI_CTRL_USB_CLK_EN);
u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PWR_UP_SHIFT);
u2o_clear(base, UTMI_CTRL, 1<<UTMI_CTRL_PLL_PWR_UP_SHIFT);
return 0;
}
int pxa_usb_phy_init(void __iomem *phy_reg)
{
mutex_lock(&phy_lock);
if (phy_init_cnt++ == 0)
usb_phy_init_internal(phy_reg);
mutex_unlock(&phy_lock);
return 0;
}
void pxa_usb_phy_deinit(void __iomem *phy_reg)
{
WARN_ON(phy_init_cnt == 0);
mutex_lock(&phy_lock);
if (--phy_init_cnt == 0)
usb_phy_deinit_internal(phy_reg);
mutex_unlock(&phy_lock);
}
#endif
#endif
#endif
#ifdef CONFIG_USB_SUPPORT
static u64 usb_dma_mask = ~(u32)0;
#ifdef CONFIG_USB_MV_UDC
struct resource pxa168_u2o_resources[] = {
/* regbase */
[0] = {
.start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
.end = PXA168_U2O_REGBASE + USB_REG_RANGE,
.flags = IORESOURCE_MEM,
.name = "capregs",
},
/* phybase */
[1] = {
.start = PXA168_U2O_PHYBASE,
.end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
.flags = IORESOURCE_MEM,
.name = "phyregs",
},
[2] = {
.start = IRQ_PXA168_USB1,
.end = IRQ_PXA168_USB1,
.flags = IORESOURCE_IRQ,
},
};
struct platform_device pxa168_device_u2o = {
.name = "mv-udc",
.id = -1,
.resource = pxa168_u2o_resources,
.num_resources = ARRAY_SIZE(pxa168_u2o_resources),
.dev = {
.dma_mask = &usb_dma_mask,
.coherent_dma_mask = 0xffffffff,
}
};
#endif /* CONFIG_USB_MV_UDC */
#ifdef CONFIG_USB_EHCI_MV_U2O
struct resource pxa168_u2oehci_resources[] = {
/* regbase */
[0] = {
.start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
.end = PXA168_U2O_REGBASE + USB_REG_RANGE,
.flags = IORESOURCE_MEM,
.name = "capregs",
},
/* phybase */
[1] = {
.start = PXA168_U2O_PHYBASE,
.end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
.flags = IORESOURCE_MEM,
.name = "phyregs",
},
[2] = {
.start = IRQ_PXA168_USB1,
.end = IRQ_PXA168_USB1,
.flags = IORESOURCE_IRQ,
},
};
struct platform_device pxa168_device_u2oehci = {
.name = "pxa-u2oehci",
.id = -1,
.dev = {
.dma_mask = &usb_dma_mask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(pxa168_u2oehci_resources),
.resource = pxa168_u2oehci_resources,
};
#endif
#if defined(CONFIG_USB_MV_OTG)
struct resource pxa168_u2ootg_resources[] = {
/* regbase */
[0] = {
.start = PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
.end = PXA168_U2O_REGBASE + USB_REG_RANGE,
.flags = IORESOURCE_MEM,
.name = "capregs",
},
/* phybase */
[1] = {
.start = PXA168_U2O_PHYBASE,
.end = PXA168_U2O_PHYBASE + USB_PHY_RANGE,
.flags = IORESOURCE_MEM,
.name = "phyregs",
},
[2] = {
.start = IRQ_PXA168_USB1,
.end = IRQ_PXA168_USB1,
.flags = IORESOURCE_IRQ,
},
};
struct platform_device pxa168_device_u2ootg = {
.name = "mv-otg",
.id = -1,
.dev = {
.dma_mask = &usb_dma_mask,
.coherent_dma_mask = 0xffffffff,
},
.num_resources = ARRAY_SIZE(pxa168_u2ootg_resources),
.resource = pxa168_u2ootg_resources,
};
#endif /* CONFIG_USB_MV_OTG */
#endif
......@@ -50,4 +50,7 @@ struct pxa_device_desc mmp2_device_##_name __initdata = { \
}
extern int pxa_register_device(struct pxa_device_desc *, void *, size_t);
extern int pxa_usb_phy_init(void __iomem *phy_reg);
extern void pxa_usb_phy_deinit(void __iomem *phy_reg);
#endif /* __MACH_DEVICE_H */
......@@ -16,6 +16,7 @@ extern void pxa168_clear_keypad_wakeup(void);
#include <plat/pxa27x_keypad.h>
#include <mach/cputype.h>
#include <linux/pxa168_eth.h>
#include <linux/platform_data/mv_usb.h>
extern struct pxa_device_desc pxa168_device_uart1;
extern struct pxa_device_desc pxa168_device_uart2;
......@@ -36,12 +37,9 @@ extern struct pxa_device_desc pxa168_device_fb;
extern struct pxa_device_desc pxa168_device_keypad;
extern struct pxa_device_desc pxa168_device_eth;
struct pxa168_usb_pdata {
/* If NULL, default phy init routine for PXA168 would be called */
int (*phy_init)(void __iomem *usb_phy_reg_base);
};
/* pdata can be NULL */
int __init pxa168_add_usb_host(struct pxa168_usb_pdata *pdata);
extern int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata);
extern struct platform_device pxa168_device_gpio;
......
......@@ -20,6 +20,9 @@ extern struct pxa_device_desc pxa910_device_pwm2;
extern struct pxa_device_desc pxa910_device_pwm3;
extern struct pxa_device_desc pxa910_device_pwm4;
extern struct pxa_device_desc pxa910_device_nand;
extern struct platform_device pxa168_device_u2o;
extern struct platform_device pxa168_device_u2ootg;
extern struct platform_device pxa168_device_u2oehci;
extern struct platform_device pxa910_device_gpio;
extern struct platform_device pxa910_device_rtc;
......
/*
* Copyright (C) 2011 Marvell International Ltd. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#ifndef __ASM_ARCH_REGS_USB_H
#define __ASM_ARCH_REGS_USB_H
#define PXA168_U2O_REGBASE (0xd4208000)
#define PXA168_U2O_PHYBASE (0xd4207000)
#define PXA168_U2H_REGBASE (0xd4209000)
#define PXA168_U2H_PHYBASE (0xd4206000)
#define MMP3_HSIC1_REGBASE (0xf0001000)
#define MMP3_HSIC1_PHYBASE (0xf0001800)
#define MMP3_HSIC2_REGBASE (0xf0002000)
#define MMP3_HSIC2_PHYBASE (0xf0002800)
#define MMP3_FSIC_REGBASE (0xf0003000)
#define MMP3_FSIC_PHYBASE (0xf0003800)
#define USB_REG_RANGE (0x1ff)
#define USB_PHY_RANGE (0xff)
/* registers */
#define U2x_CAPREGS_OFFSET 0x100
/* phy regs */
#define UTMI_REVISION 0x0
#define UTMI_CTRL 0x4
#define UTMI_PLL 0x8
#define UTMI_TX 0xc
#define UTMI_RX 0x10
#define UTMI_IVREF 0x14
#define UTMI_T0 0x18
#define UTMI_T1 0x1c
#define UTMI_T2 0x20
#define UTMI_T3 0x24
#define UTMI_T4 0x28
#define UTMI_T5 0x2c
#define UTMI_RESERVE 0x30
#define UTMI_USB_INT 0x34
#define UTMI_DBG_CTL 0x38
#define UTMI_OTG_ADDON 0x3c
/* For UTMICTRL Register */
#define UTMI_CTRL_USB_CLK_EN (1 << 31)
/* pxa168 */
#define UTMI_CTRL_SUSPEND_SET1 (1 << 30)
#define UTMI_CTRL_SUSPEND_SET2 (1 << 29)
#define UTMI_CTRL_RXBUF_PDWN (1 << 24)
#define UTMI_CTRL_TXBUF_PDWN (1 << 11)
#define UTMI_CTRL_INPKT_DELAY_SHIFT 30
#define UTMI_CTRL_INPKT_DELAY_SOF_SHIFT 28
#define UTMI_CTRL_PU_REF_SHIFT 20
#define UTMI_CTRL_ARC_PULLDN_SHIFT 12
#define UTMI_CTRL_PLL_PWR_UP_SHIFT 1
#define UTMI_CTRL_PWR_UP_SHIFT 0
/* For UTMI_PLL Register */
#define UTMI_PLL_PLLCALI12_SHIFT 29
#define UTMI_PLL_PLLCALI12_MASK (0x3 << 29)
#define UTMI_PLL_PLLVDD18_SHIFT 27
#define UTMI_PLL_PLLVDD18_MASK (0x3 << 27)
#define UTMI_PLL_PLLVDD12_SHIFT 25
#define UTMI_PLL_PLLVDD12_MASK (0x3 << 25)
#define UTMI_PLL_CLK_BLK_EN_SHIFT 24
#define CLK_BLK_EN (0x1 << 24)
#define PLL_READY (0x1 << 23)
#define KVCO_EXT (0x1 << 22)
#define VCOCAL_START (0x1 << 21)
#define UTMI_PLL_KVCO_SHIFT 15
#define UTMI_PLL_KVCO_MASK (0x7 << 15)
#define UTMI_PLL_ICP_SHIFT 12
#define UTMI_PLL_ICP_MASK (0x7 << 12)
#define UTMI_PLL_FBDIV_SHIFT 4
#define UTMI_PLL_FBDIV_MASK (0xFF << 4)
#define UTMI_PLL_REFDIV_SHIFT 0
#define UTMI_PLL_REFDIV_MASK (0xF << 0)
/* For UTMI_TX Register */
#define UTMI_TX_REG_EXT_FS_RCAL_SHIFT 27
#define UTMI_TX_REG_EXT_FS_RCAL_MASK (0xf << 27)
#define UTMI_TX_REG_EXT_FS_RCAL_EN_SHIFT 26
#define UTMI_TX_REG_EXT_FS_RCAL_EN_MASK (0x1 << 26)
#define UTMI_TX_TXVDD12_SHIFT 22
#define UTMI_TX_TXVDD12_MASK (0x3 << 22)
#define UTMI_TX_CK60_PHSEL_SHIFT 17
#define UTMI_TX_CK60_PHSEL_MASK (0xf << 17)
#define UTMI_TX_IMPCAL_VTH_SHIFT 14
#define UTMI_TX_IMPCAL_VTH_MASK (0x7 << 14)
#define REG_RCAL_START (0x1 << 12)
#define UTMI_TX_LOW_VDD_EN_SHIFT 11
#define UTMI_TX_AMP_SHIFT 0
#define UTMI_TX_AMP_MASK (0x7 << 0)
/* For UTMI_RX Register */
#define UTMI_REG_SQ_LENGTH_SHIFT 15
#define UTMI_REG_SQ_LENGTH_MASK (0x3 << 15)
#define UTMI_RX_SQ_THRESH_SHIFT 4
#define UTMI_RX_SQ_THRESH_MASK (0xf << 4)
#define UTMI_OTG_ADDON_OTG_ON (1 << 0)
/* For MMP3 USB Phy */
#define USB2_PLL_REG0 0x4
#define USB2_PLL_REG1 0x8
#define USB2_TX_REG0 0x10
#define USB2_TX_REG1 0x14
#define USB2_TX_REG2 0x18
#define USB2_RX_REG0 0x20
#define USB2_RX_REG1 0x24
#define USB2_RX_REG2 0x28
#define USB2_ANA_REG0 0x30
#define USB2_ANA_REG1 0x34
#define USB2_ANA_REG2 0x38
#define USB2_DIG_REG0 0x3C
#define USB2_DIG_REG1 0x40
#define USB2_DIG_REG2 0x44
#define USB2_DIG_REG3 0x48
#define USB2_TEST_REG0 0x4C
#define USB2_TEST_REG1 0x50
#define USB2_TEST_REG2 0x54
#define USB2_CHARGER_REG0 0x58
#define USB2_OTG_REG0 0x5C
#define USB2_PHY_MON0 0x60
#define USB2_RESETVE_REG0 0x64
#define USB2_ICID_REG0 0x78
#define USB2_ICID_REG1 0x7C
/* USB2_PLL_REG0 */
/* This is for Ax stepping */
#define USB2_PLL_FBDIV_SHIFT_MMP3 0
#define USB2_PLL_FBDIV_MASK_MMP3 (0xFF << 0)
#define USB2_PLL_REFDIV_SHIFT_MMP3 8
#define USB2_PLL_REFDIV_MASK_MMP3 (0xF << 8)
#define USB2_PLL_VDD12_SHIFT_MMP3 12
#define USB2_PLL_VDD18_SHIFT_MMP3 14
/* This is for B0 stepping */
#define USB2_PLL_FBDIV_SHIFT_MMP3_B0 0
#define USB2_PLL_REFDIV_SHIFT_MMP3_B0 9
#define USB2_PLL_VDD18_SHIFT_MMP3_B0 14
#define USB2_PLL_FBDIV_MASK_MMP3_B0 0x01FF
#define USB2_PLL_REFDIV_MASK_MMP3_B0 0x3E00
#define USB2_PLL_CAL12_SHIFT_MMP3 0
#define USB2_PLL_CALI12_MASK_MMP3 (0x3 << 0)
#define USB2_PLL_VCOCAL_START_SHIFT_MMP3 2
#define USB2_PLL_KVCO_SHIFT_MMP3 4
#define USB2_PLL_KVCO_MASK_MMP3 (0x7<<4)
#define USB2_PLL_ICP_SHIFT_MMP3 8
#define USB2_PLL_ICP_MASK_MMP3 (0x7<<8)
#define USB2_PLL_LOCK_BYPASS_SHIFT_MMP3 12
#define USB2_PLL_PU_PLL_SHIFT_MMP3 13
#define USB2_PLL_PU_PLL_MASK (0x1 << 13)
#define USB2_PLL_READY_MASK_MMP3 (0x1 << 15)
/* USB2_TX_REG0 */
#define USB2_TX_IMPCAL_VTH_SHIFT_MMP3 8
#define USB2_TX_IMPCAL_VTH_MASK_MMP3 (0x7 << 8)
#define USB2_TX_RCAL_START_SHIFT_MMP3 13
/* USB2_TX_REG1 */
#define USB2_TX_CK60_PHSEL_SHIFT_MMP3 0
#define USB2_TX_CK60_PHSEL_MASK_MMP3 (0xf << 0)
#define USB2_TX_AMP_SHIFT_MMP3 4
#define USB2_TX_AMP_MASK_MMP3 (0x7 << 4)
#define USB2_TX_VDD12_SHIFT_MMP3 8
#define USB2_TX_VDD12_MASK_MMP3 (0x3 << 8)
/* USB2_TX_REG2 */
#define USB2_TX_DRV_SLEWRATE_SHIFT 10
/* USB2_RX_REG0 */
#define USB2_RX_SQ_THRESH_SHIFT_MMP3 4
#define USB2_RX_SQ_THRESH_MASK_MMP3 (0xf << 4)
#define USB2_RX_SQ_LENGTH_SHIFT_MMP3 10
#define USB2_RX_SQ_LENGTH_MASK_MMP3 (0x3 << 10)
/* USB2_ANA_REG1*/
#define USB2_ANA_PU_ANA_SHIFT_MMP3 14
/* USB2_OTG_REG0 */
#define USB2_OTG_PU_OTG_SHIFT_MMP3 3
/* fsic registers */
#define FSIC_MISC 0x4
#define FSIC_INT 0x28
#define FSIC_CTRL 0x30
/* HSIC registers */
#define HSIC_PAD_CTRL 0x4
#define HSIC_CTRL 0x8
#define HSIC_CTRL_HSIC_ENABLE (1<<7)
#define HSIC_CTRL_PLL_BYPASS (1<<4)
#define TEST_GRP_0 0xc
#define TEST_GRP_1 0x10
#define HSIC_INT 0x14
#define HSIC_INT_READY_INT_EN (1<<10)
#define HSIC_INT_CONNECT_INT_EN (1<<9)
#define HSIC_INT_CORE_INT_EN (1<<8)
#define HSIC_INT_HS_READY (1<<2)
#define HSIC_INT_CONNECT (1<<1)
#define HSIC_INT_CORE (1<<0)
#define HSIC_CONFIG 0x18
#define USBHSIC_CTRL 0x20
#define HSIC_USB_CTRL 0x28
#define HSIC_USB_CTRL_CLKEN 1
#define HSIC_USB_CLK_PHY 0x0
#define HSIC_USB_CLK_PMU 0x1
#endif /* __ASM_ARCH_PXA_U2O_H */
......@@ -14,6 +14,7 @@
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/platform_device.h>
#include <linux/platform_data/mv_usb.h>
#include <asm/mach/time.h>
#include <asm/system_misc.h>
......@@ -27,6 +28,7 @@
#include <mach/mfp.h>
#include <linux/dma-mapping.h>
#include <mach/pxa168.h>
#include <mach/regs-usb.h>
#include "common.h"
#include "clock.h"
......@@ -93,7 +95,7 @@ static struct clk_lookup pxa168_clkregs[] = {
INIT_CLKREG(&clk_gpio, "pxa-gpio", NULL),
INIT_CLKREG(&clk_keypad, "pxa27x-keypad", NULL),
INIT_CLKREG(&clk_eth, "pxa168-eth", "MFUCLK"),
INIT_CLKREG(&clk_usb, "pxa168-ehci", "PXA168-USBCLK"),
INIT_CLKREG(&clk_usb, NULL, "PXA168-USBCLK"),
INIT_CLKREG(&clk_rtc, "sa1100-rtc", NULL),
};
......@@ -184,17 +186,17 @@ struct platform_device pxa168_device_gpio = {
struct resource pxa168_usb_host_resources[] = {
/* USB Host conroller register base */
[0] = {
.start = 0xd4209000,
.end = 0xd4209000 + 0x200,
.start = PXA168_U2H_REGBASE + U2x_CAPREGS_OFFSET,
.end = PXA168_U2H_REGBASE + USB_REG_RANGE,
.flags = IORESOURCE_MEM,
.name = "pxa168-usb-host",
.name = "capregs",
},
/* USB PHY register base */
[1] = {
.start = 0xd4206000,
.end = 0xd4206000 + 0xff,
.start = PXA168_U2H_PHYBASE,
.end = PXA168_U2H_PHYBASE + USB_PHY_RANGE,
.flags = IORESOURCE_MEM,
.name = "pxa168-usb-phy",
.name = "phyregs",
},
[2] = {
.start = IRQ_PXA168_USB2,
......@@ -205,7 +207,7 @@ struct resource pxa168_usb_host_resources[] = {
static u64 pxa168_usb_host_dmamask = DMA_BIT_MASK(32);
struct platform_device pxa168_device_usb_host = {
.name = "pxa168-ehci",
.name = "pxa-sph",
.id = -1,
.dev = {
.dma_mask = &pxa168_usb_host_dmamask,
......@@ -216,7 +218,7 @@ struct platform_device pxa168_device_usb_host = {
.resource = pxa168_usb_host_resources,
};
int __init pxa168_add_usb_host(struct pxa168_usb_pdata *pdata)
int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata)
{
pxa168_device_usb_host.dev.platform_data = pdata;
return platform_device_register(&pxa168_device_usb_host);
......
......@@ -109,7 +109,7 @@ static struct clk_lookup pxa910_clkregs[] = {
INIT_CLKREG(&clk_pwm4, "pxa910-pwm.3", NULL),
INIT_CLKREG(&clk_nand, "pxa3xx-nand", NULL),
INIT_CLKREG(&clk_gpio, "pxa-gpio", NULL),
INIT_CLKREG(&clk_u2o, "pxa-u2o", "U2OCLK"),
INIT_CLKREG(&clk_u2o, NULL, "U2OCLK"),
INIT_CLKREG(&clk_rtc, "sa1100-rtc", NULL),
};
......
......@@ -18,6 +18,7 @@
#include <linux/i2c/pca953x.h>
#include <linux/gpio.h>
#include <linux/mfd/88pm860x.h>
#include <linux/platform_data/mv_usb.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
......@@ -26,6 +27,7 @@
#include <mach/mfp-pxa910.h>
#include <mach/pxa910.h>
#include <mach/irqs.h>
#include <mach/regs-usb.h>
#include "common.h"
......@@ -155,6 +157,26 @@ static struct i2c_board_info ttc_dkb_i2c_info[] = {
},
};
#ifdef CONFIG_USB_SUPPORT
#if defined(CONFIG_USB_MV_UDC) || defined(CONFIG_USB_EHCI_MV_U2O)
static char *pxa910_usb_clock_name[] = {
[0] = "U2OCLK",
};
static struct mv_usb_platform_data ttc_usb_pdata = {
.clknum = 1,
.clkname = pxa910_usb_clock_name,
.vbus = NULL,
.mode = MV_USB_MODE_OTG,
.otg_force_a_bus_req = 1,
.phy_init = pxa_usb_phy_init,
.phy_deinit = pxa_usb_phy_deinit,
.set_vbus = NULL,
};
#endif
#endif
static void __init ttc_dkb_init(void)
{
mfp_config(ARRAY_AND_SIZE(ttc_dkb_pin_config));
......@@ -165,6 +187,21 @@ static void __init ttc_dkb_init(void)
/* off-chip devices */
pxa910_add_twsi(0, NULL, ARRAY_AND_SIZE(ttc_dkb_i2c_info));
platform_add_devices(ARRAY_AND_SIZE(ttc_dkb_devices));
#ifdef CONFIG_USB_MV_UDC
pxa168_device_u2o.dev.platform_data = &ttc_usb_pdata;
platform_device_register(&pxa168_device_u2o);
#endif
#ifdef CONFIG_USB_EHCI_MV_U2O
pxa168_device_u2oehci.dev.platform_data = &ttc_usb_pdata;
platform_device_register(&pxa168_device_u2oehci);
#endif
#ifdef CONFIG_USB_MV_OTG
pxa168_device_u2ootg.dev.platform_data = &ttc_usb_pdata;
platform_device_register(&pxa168_device_u2ootg);
#endif
}
MACHINE_START(TTC_DKB, "PXA910-based TTC_DKB Development Platform")
......
......@@ -17,6 +17,7 @@ config ARCH_OMAP2PLUS_TYPICAL
select MENELAUS if ARCH_OMAP2
select TWL4030_CORE if ARCH_OMAP3 || ARCH_OMAP4
select TWL4030_POWER if ARCH_OMAP3 || ARCH_OMAP4
select HIGHMEM
help
Compile a kernel suitable for booting most boards
......
......@@ -384,6 +384,11 @@ static struct platform_device sdp4430_dmic_codec = {
.id = -1,
};
static struct platform_device sdp4430_hdmi_audio_codec = {
.name = "hdmi-audio-codec",
.id = -1,
};
static struct omap_abe_twl6040_data sdp4430_abe_audio_data = {
.card_name = "SDP4430",
.has_hs = ABE_TWL6040_LEFT | ABE_TWL6040_RIGHT,
......@@ -418,6 +423,7 @@ static struct platform_device *sdp4430_devices[] __initdata = {
&sdp4430_vbat,
&sdp4430_dmic_codec,
&sdp4430_abe_audio,
&sdp4430_hdmi_audio_codec,
};
static struct omap_musb_board_data musb_board_data = {
......@@ -571,7 +577,9 @@ static int __init omap4_i2c_init(void)
TWL_COMMON_REGULATOR_VANA |
TWL_COMMON_REGULATOR_VCXIO |
TWL_COMMON_REGULATOR_VUSB |
TWL_COMMON_REGULATOR_CLK32KG);
TWL_COMMON_REGULATOR_CLK32KG |
TWL_COMMON_REGULATOR_V1V8 |
TWL_COMMON_REGULATOR_V2V1);
omap4_pmic_init("twl6030", &sdp4430_twldata,
&twl6040_data, OMAP44XX_IRQ_SYS_2N);
omap_register_i2c_bus(2, 400, NULL, 0);
......
......@@ -30,6 +30,7 @@
#include "common.h"
#include <plat/usb.h>
#include "am35xx-emac.h"
#include "mux.h"
#include "control.h"
......@@ -90,6 +91,7 @@ static void __init am3517_crane_init(void)
}
usbhs_init(&usbhs_bdata);
am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1);
}
MACHINE_START(CRANEBOARD, "AM3517/05 CRANEBOARD")
......
......@@ -476,6 +476,10 @@ static struct twl4030_gpio_platform_data cm_t35_gpio_data = {
.setup = cm_t35_twl_gpio_setup,
};
static struct twl4030_power_data cm_t35_power_data = {
.use_poweroff = true,
};
static struct twl4030_platform_data cm_t35_twldata = {
/* platform_data for children goes here */
.keypad = &cm_t35_kp_data,
......@@ -483,6 +487,7 @@ static struct twl4030_platform_data cm_t35_twldata = {
.vmmc1 = &cm_t35_vmmc1,
.vsim = &cm_t35_vsim,
.vio = &cm_t35_vio,
.power = &cm_t35_power_data,
};
static void __init cm_t35_init_i2c(void)
......
......@@ -87,7 +87,7 @@ static struct omap_onenand_platform_data board_onenand_data = {
.dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
};
static void
void
__init board_onenand_init(struct mtd_partition *onenand_parts,
u8 nr_parts, u8 cs)
{
......@@ -98,7 +98,7 @@ __init board_onenand_init(struct mtd_partition *onenand_parts,
gpmc_onenand_init(&board_onenand_data);
}
#else
static void
void
__init board_onenand_init(struct mtd_partition *nor_parts, u8 nr_parts, u8 cs)
{
}
......
......@@ -47,3 +47,14 @@ static inline void board_nand_init(struct mtd_partition *nand_parts,
{
}
#endif
#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
extern void board_onenand_init(struct mtd_partition *nand_parts,
u8 nr_parts, u8 cs);
#else
static inline void board_onenand_init(struct mtd_partition *nand_parts,
u8 nr_parts, u8 cs)
{
}
#endif
......@@ -24,6 +24,8 @@
#include <linux/i2c/twl.h>
#include <linux/mmc/host.h>
#include <linux/mtd/nand.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
......@@ -39,6 +41,8 @@
#include "hsmmc.h"
#include "sdram-numonyx-m65kxxxxam.h"
#include "common-board-devices.h"
#include "board-flash.h"
#include "control.h"
#define IGEP2_SMSC911X_CS 5
#define IGEP2_SMSC911X_GPIO 176
......@@ -60,6 +64,10 @@
#define IGEP3_GPIO_LED1_RED 16
#define IGEP3_GPIO_USBH_NRESET 183
#define IGEP_SYSBOOT_MASK 0x1f
#define IGEP_SYSBOOT_NAND 0x0f
#define IGEP_SYSBOOT_ONENAND 0x10
/*
* IGEP2 Hardware Revision Table
*
......@@ -110,8 +118,10 @@ static void __init igep2_get_revision(void)
gpio_free(IGEP2_GPIO_LED1_RED);
}
#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
#if defined(CONFIG_MTD_ONENAND_OMAP2) || \
defined(CONFIG_MTD_ONENAND_OMAP2_MODULE) || \
defined(CONFIG_MTD_NAND_OMAP2) || \
defined(CONFIG_MTD_NAND_OMAP2_MODULE)
#define ONENAND_MAP 0x20000000
......@@ -123,7 +133,7 @@ static void __init igep2_get_revision(void)
* So MTD regards it as 4KiB page size and 256KiB block size 64*(2*2048)
*/
static struct mtd_partition igep_onenand_partitions[] = {
static struct mtd_partition igep_flash_partitions[] = {
{
.name = "X-Loader",
.offset = 0,
......@@ -151,50 +161,28 @@ static struct mtd_partition igep_onenand_partitions[] = {
},
};
static struct omap_onenand_platform_data igep_onenand_data = {
.parts = igep_onenand_partitions,
.nr_parts = ARRAY_SIZE(igep_onenand_partitions),
.dma_channel = -1, /* disable DMA in OMAP OneNAND driver */
};
static struct platform_device igep_onenand_device = {
.name = "omap2-onenand",
.id = -1,
.dev = {
.platform_data = &igep_onenand_data,
},
};
static inline u32 igep_get_sysboot_value(void)
{
return omap_ctrl_readl(OMAP343X_CONTROL_STATUS) & IGEP_SYSBOOT_MASK;
}
static void __init igep_flash_init(void)
{
u8 cs = 0;
u8 onenandcs = GPMC_CS_NUM + 1;
for (cs = 0; cs < GPMC_CS_NUM; cs++) {
u32 ret;
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
/* Check if NAND/oneNAND is configured */
if ((ret & 0xC00) == 0x800)
/* NAND found */
pr_err("IGEP: Unsupported NAND found\n");
else {
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG7);
if ((ret & 0x3F) == (ONENAND_MAP >> 24))
/* ONENAND found */
onenandcs = cs;
}
}
if (onenandcs > GPMC_CS_NUM) {
pr_err("IGEP: Unable to find configuration in GPMC\n");
return;
u32 mux;
mux = igep_get_sysboot_value();
if (mux == IGEP_SYSBOOT_NAND) {
pr_info("IGEP: initializing NAND memory device\n");
board_nand_init(igep_flash_partitions,
ARRAY_SIZE(igep_flash_partitions),
0, NAND_BUSWIDTH_16);
} else if (mux == IGEP_SYSBOOT_ONENAND) {
pr_info("IGEP: initializing OneNAND memory device\n");
board_onenand_init(igep_flash_partitions,
ARRAY_SIZE(igep_flash_partitions), 0);
} else {
pr_err("IGEP: Flash: unsupported sysboot sequence found\n");
}
igep_onenand_data.cs = onenandcs;
if (platform_device_register(&igep_onenand_device) < 0)
pr_err("IGEP: Unable to register OneNAND device\n");
}
#else
......
......@@ -83,11 +83,13 @@ static struct {
int usb_pwr_level;
int reset_gpio;
int usr_button_gpio;
int mmc_caps;
} beagle_config = {
.mmc1_gpio_wp = -EINVAL,
.usb_pwr_level = GPIOF_OUT_INIT_LOW,
.reset_gpio = 129,
.usr_button_gpio = 4,
.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
};
static struct gpio omap3_beagle_rev_gpios[] __initdata = {
......@@ -145,10 +147,12 @@ static void __init omap3_beagle_init_rev(void)
printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
beagle_config.usb_pwr_level = GPIOF_OUT_INIT_HIGH;
beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
break;
case 2:
printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
break;
default:
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
......@@ -225,7 +229,7 @@ static struct omap_dss_board_info beagle_dss_data = {
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_wp = -EINVAL,
.deferred = true,
},
......@@ -497,6 +501,7 @@ static void __init omap3_beagle_init(void)
if (beagle_config.mmc1_gpio_wp != -EINVAL)
omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
mmc[0].caps = beagle_config.mmc_caps;
omap_hsmmc_init(mmc);
omap3_beagle_i2c_init();
......
......@@ -4,8 +4,9 @@
* Copyright (C) 2010 Li-Pro.Net
* Stephan Linz <linz@li-pro.net>
*
* Copyright (C) 2010 Logic Product Development, Inc.
* Copyright (C) 2010-2012 Logic Product Development, Inc.
* Peter Barada <peter.barada@logicpd.com>
* Ashwin BIhari <ashwin.bihari@logicpd.com>
*
* Modified from Beagle, EVM, and RX51
*
......@@ -45,6 +46,7 @@
#include <plat/gpmc-smsc911x.h>
#include <plat/gpmc.h>
#include <plat/sdrc.h>
#include <plat/usb.h>
#define OMAP3LOGIC_SMSC911X_CS 1
......@@ -85,6 +87,11 @@ static struct twl4030_gpio_platform_data omap3logic_gpio_data = {
| BIT(13) | BIT(15) | BIT(16) | BIT(17),
};
static struct twl4030_usb_data omap3logic_usb_data = {
.usb_mode = T2_USB_MODE_ULPI,
};
static struct twl4030_platform_data omap3logic_twldata = {
.irq_base = TWL4030_IRQ_BASE,
.irq_end = TWL4030_IRQ_END,
......@@ -92,6 +99,7 @@ static struct twl4030_platform_data omap3logic_twldata = {
/* platform_data for children goes here */
.gpio = &omap3logic_gpio_data,
.vmmc1 = &omap3logic_vmmc1,
.usb = &omap3logic_usb_data,
};
static int __init omap3logic_i2c_init(void)
......@@ -185,6 +193,20 @@ static inline void __init board_smsc911x_init(void)
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
/* mUSB */
OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
......@@ -205,6 +227,8 @@ static void __init omap3logic_init(void)
board_mmc_init();
board_smsc911x_init();
usb_musb_init(NULL);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
......
......@@ -28,6 +28,7 @@
#include <linux/mfd/twl6040.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/ti_wilink_st.h>
#include <linux/wl12xx.h>
#include <linux/platform_data/omap-abe-twl6040.h>
......@@ -58,12 +59,21 @@
#define HDMI_GPIO_HPD 63 /* Hotplug detect */
/* wl127x BT, FM, GPS connectivity chip */
static int wl1271_gpios[] = {46, -1, -1};
static struct ti_st_plat_data wilink_platform_data = {
.nshutdown_gpio = 46,
.dev_name = "/dev/ttyO1",
.flow_cntrl = 1,
.baud_rate = 3000000,
.chip_enable = NULL,
.suspend = NULL,
.resume = NULL,
};
static struct platform_device wl1271_device = {
.name = "kim",
.id = -1,
.dev = {
.platform_data = &wl1271_gpios,
.platform_data = &wilink_platform_data,
},
};
......@@ -117,6 +127,11 @@ static struct platform_device panda_abe_audio = {
},
};
static struct platform_device panda_hdmi_audio_codec = {
.name = "hdmi-audio-codec",
.id = -1,
};
static struct platform_device btwilink_device = {
.name = "btwilink",
.id = -1,
......@@ -126,6 +141,7 @@ static struct platform_device *panda_devices[] __initdata = {
&leds_gpio,
&wl1271_device,
&panda_abe_audio,
&panda_hdmi_audio_codec,
&btwilink_device,
};
......@@ -274,7 +290,9 @@ static int __init omap4_panda_i2c_init(void)
TWL_COMMON_REGULATOR_VANA |
TWL_COMMON_REGULATOR_VCXIO |
TWL_COMMON_REGULATOR_VUSB |
TWL_COMMON_REGULATOR_CLK32KG);
TWL_COMMON_REGULATOR_CLK32KG |
TWL_COMMON_REGULATOR_V1V8 |
TWL_COMMON_REGULATOR_V2V1);
omap4_pmic_init("twl6030", &omap4_panda_twldata,
&twl6040_data, OMAP44XX_IRQ_SYS_2N);
omap_register_i2c_bus(2, 400, NULL, 0);
......
......@@ -44,6 +44,7 @@
#include <linux/leds-lp5523.h>
#include <../drivers/staging/iio/light/tsl2563.h>
#include <linux/lis3lv02d.h>
#include "mux.h"
#include "hsmmc.h"
......@@ -63,6 +64,9 @@
#define RX51_TSC2005_RESET_GPIO 104
#define RX51_TSC2005_IRQ_GPIO 100
#define LIS302_IRQ1_GPIO 181
#define LIS302_IRQ2_GPIO 180 /* Not yet in use */
/* list all spi devices here */
enum {
RX51_SPI_WL1251,
......@@ -73,6 +77,77 @@ enum {
static struct wl12xx_platform_data wl1251_pdata;
static struct tsc2005_platform_data tsc2005_pdata;
#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
static int lis302_setup(void)
{
int err;
int irq1 = LIS302_IRQ1_GPIO;
int irq2 = LIS302_IRQ2_GPIO;
/* gpio for interrupt pin 1 */
err = gpio_request(irq1, "lis3lv02dl_irq1");
if (err) {
printk(KERN_ERR "lis3lv02dl: gpio request failed\n");
goto out;
}
/* gpio for interrupt pin 2 */
err = gpio_request(irq2, "lis3lv02dl_irq2");
if (err) {
gpio_free(irq1);
printk(KERN_ERR "lis3lv02dl: gpio request failed\n");
goto out;
}
gpio_direction_input(irq1);
gpio_direction_input(irq2);
out:
return err;
}
static int lis302_release(void)
{
gpio_free(LIS302_IRQ1_GPIO);
gpio_free(LIS302_IRQ2_GPIO);
return 0;
}
static struct lis3lv02d_platform_data rx51_lis3lv02d_data = {
.click_flags = LIS3_CLICK_SINGLE_X | LIS3_CLICK_SINGLE_Y |
LIS3_CLICK_SINGLE_Z,
/* Limits are 0.5g * value */
.click_thresh_x = 8,
.click_thresh_y = 8,
.click_thresh_z = 10,
/* Click must be longer than time limit */
.click_time_limit = 9,
/* Kind of debounce filter */
.click_latency = 50,
/* Limits for all axis. millig-value / 18 to get HW values */
.wakeup_flags = LIS3_WAKEUP_X_HI | LIS3_WAKEUP_Y_HI,
.wakeup_thresh = 800 / 18,
.wakeup_flags2 = LIS3_WAKEUP_Z_HI ,
.wakeup_thresh2 = 900 / 18,
.hipass_ctrl = LIS3_HIPASS1_DISABLE | LIS3_HIPASS2_DISABLE,
/* Interrupt line 2 for click detection, line 1 for thresholds */
.irq_cfg = LIS3_IRQ2_CLICK | LIS3_IRQ1_FF_WU_12,
.axis_x = LIS3_DEV_X,
.axis_y = LIS3_INV_DEV_Y,
.axis_z = LIS3_INV_DEV_Z,
.setup_resources = lis302_setup,
.release_resources = lis302_release,
.st_min_limits = {-32, 3, 3},
.st_max_limits = {-3, 32, 32},
.irq2 = OMAP_GPIO_IRQ(LIS302_IRQ2_GPIO),
};
#endif
#if defined(CONFIG_SENSORS_TSL2563) || defined(CONFIG_SENSORS_TSL2563_MODULE)
static struct tsl2563_platform_data rx51_tsl2563_platform_data = {
.cover_comp_gain = 16,
......@@ -950,6 +1025,16 @@ static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_2[] = {
}
};
static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_3[] = {
#if defined(CONFIG_SENSORS_LIS3_I2C) || defined(CONFIG_SENSORS_LIS3_I2C_MODULE)
{
I2C_BOARD_INFO("lis3lv02d", 0x1d),
.platform_data = &rx51_lis3lv02d_data,
.irq = OMAP_GPIO_IRQ(LIS302_IRQ1_GPIO),
},
#endif
};
static int __init rx51_i2c_init(void)
{
if ((system_rev >= SYSTEM_REV_S_USES_VAUX3 && system_rev < 0x100) ||
......@@ -971,7 +1056,8 @@ static int __init rx51_i2c_init(void)
omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata);
omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2,
ARRAY_SIZE(rx51_peripherals_i2c_board_info_2));
omap_register_i2c_bus(3, 400, NULL, 0);
omap_register_i2c_bus(3, 400, rx51_peripherals_i2c_board_info_3,
ARRAY_SIZE(rx51_peripherals_i2c_board_info_3));
return 0;
}
......
......@@ -354,6 +354,36 @@ static void __init omap_init_dmic(void)
static inline void omap_init_dmic(void) {}
#endif
#if defined(CONFIG_SND_OMAP_SOC_OMAP_HDMI) || \
defined(CONFIG_SND_OMAP_SOC_OMAP_HDMI_MODULE)
static struct platform_device omap_hdmi_audio = {
.name = "omap-hdmi-audio",
.id = -1,
};
static void __init omap_init_hdmi_audio(void)
{
struct omap_hwmod *oh;
struct platform_device *pdev;
oh = omap_hwmod_lookup("dss_hdmi");
if (!oh) {
printk(KERN_ERR "Could not look up dss_hdmi hw_mod\n");
return;
}
pdev = omap_device_build("omap-hdmi-audio-dai",
-1, oh, NULL, 0, NULL, 0, 0);
WARN(IS_ERR(pdev),
"Can't build omap_device for omap-hdmi-audio-dai.\n");
platform_device_register(&omap_hdmi_audio);
}
#else
static inline void omap_init_hdmi_audio(void) {}
#endif
#if defined(CONFIG_SPI_OMAP24XX) || defined(CONFIG_SPI_OMAP24XX_MODULE)
#include <plat/mcspi.h>
......@@ -701,6 +731,7 @@ static int __init omap2_init_devices(void)
*/
omap_init_audio();
omap_init_camera();
omap_init_hdmi_audio();
omap_init_mbox();
/* If dtb is there, the devices will be created dynamically */
if (!of_have_populated_dt()) {
......
......@@ -266,6 +266,7 @@ static struct regulator_init_data omap4_vdac_idata = {
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.supply_regulator = "V2V1",
};
static struct regulator_init_data omap4_vaux2_idata = {
......@@ -356,6 +357,7 @@ static struct regulator_init_data omap4_vcxio_idata = {
},
.num_consumer_supplies = ARRAY_SIZE(omap4_vcxio_supply),
.consumer_supplies = omap4_vcxio_supply,
.supply_regulator = "V2V1",
};
static struct regulator_init_data omap4_vusb_idata = {
......@@ -439,6 +441,41 @@ static struct twl_regulator_driver_data omap4_vdd3_drvdata = {
.set_voltage = twl_set_voltage,
};
static struct regulator_consumer_supply omap4_v1v8_supply[] = {
REGULATOR_SUPPLY("vio", "1-004b"),
};
static struct regulator_init_data omap4_v1v8_idata = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
.always_on = true,
},
.num_consumer_supplies = ARRAY_SIZE(omap4_v1v8_supply),
.consumer_supplies = omap4_v1v8_supply,
};
static struct regulator_consumer_supply omap4_v2v1_supply[] = {
REGULATOR_SUPPLY("v2v1", "1-004b"),
};
static struct regulator_init_data omap4_v2v1_idata = {
.constraints = {
.min_uV = 2100000,
.max_uV = 2100000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(omap4_v2v1_supply),
.consumer_supplies = omap4_v2v1_supply,
};
void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
u32 pdata_flags, u32 regulators_flags)
{
......@@ -497,5 +534,11 @@ void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
if (regulators_flags & TWL_COMMON_REGULATOR_CLK32KG &&
!pmic_data->clk32kg)
pmic_data->clk32kg = &omap4_clk32kg_idata;
if (regulators_flags & TWL_COMMON_REGULATOR_V1V8 && !pmic_data->v1v8)
pmic_data->v1v8 = &omap4_v1v8_idata;
if (regulators_flags & TWL_COMMON_REGULATOR_V2V1 && !pmic_data->v2v1)
pmic_data->v2v1 = &omap4_v2v1_idata;
}
#endif /* CONFIG_ARCH_OMAP4 */
......@@ -22,6 +22,8 @@
#define TWL_COMMON_REGULATOR_VCXIO (1 << 8)
#define TWL_COMMON_REGULATOR_VUSB (1 << 9)
#define TWL_COMMON_REGULATOR_CLK32KG (1 << 10)
#define TWL_COMMON_REGULATOR_V1V8 (1 << 11)
#define TWL_COMMON_REGULATOR_V2V1 (1 << 12)
/* TWL4030 LDO regulators */
#define TWL_COMMON_REGULATOR_VPLL1 (1 << 4)
......
......@@ -252,27 +252,6 @@ static int __init dns323_read_mac_addr(void)
* GPIO LEDs (simple - doesn't use hardware blinking support)
*/
#define ORION_BLINK_HALF_PERIOD 100 /* ms */
static int dns323_gpio_blink_set(unsigned gpio, int state,
unsigned long *delay_on, unsigned long *delay_off)
{
if (delay_on && delay_off && !*delay_on && !*delay_off)
*delay_on = *delay_off = ORION_BLINK_HALF_PERIOD;
switch(state) {
case GPIO_LED_NO_BLINK_LOW:
case GPIO_LED_NO_BLINK_HIGH:
orion_gpio_set_blink(gpio, 0);
gpio_set_value(gpio, state);
break;
case GPIO_LED_BLINK:
orion_gpio_set_blink(gpio, 1);
}
return 0;
}
static struct gpio_led dns323ab_leds[] = {
{
.name = "power:blue",
......@@ -311,13 +290,13 @@ static struct gpio_led dns323c_leds[] = {
static struct gpio_led_platform_data dns323ab_led_data = {
.num_leds = ARRAY_SIZE(dns323ab_leds),
.leds = dns323ab_leds,
.gpio_blink_set = dns323_gpio_blink_set,
.gpio_blink_set = orion_gpio_led_blink_set,
};
static struct gpio_led_platform_data dns323c_led_data = {
.num_leds = ARRAY_SIZE(dns323c_leds),
.leds = dns323c_leds,
.gpio_blink_set = dns323_gpio_blink_set,
.gpio_blink_set = orion_gpio_led_blink_set,
};
static struct platform_device dns323_gpio_leds = {
......
......@@ -732,9 +732,7 @@ static inline void balloon3_nand_init(void) {}
#if defined(CONFIG_REGULATOR_MAX1586) || \
defined(CONFIG_REGULATOR_MAX1586_MODULE)
static struct regulator_consumer_supply balloon3_max1587a_consumers[] = {
{
.supply = "vcc_core",
}
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data balloon3_max1587a_v3_info = {
......
......@@ -713,9 +713,7 @@ struct da9030_battery_info cm_x300_battery_info = {
};
static struct regulator_consumer_supply buck2_consumers[] = {
{
.supply = "vcc_core",
},
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data buck2_data = {
......
......@@ -1085,10 +1085,7 @@ static void __init em_x270_userspace_consumers_init(void)
/* DA9030 related initializations */
#define REGULATOR_CONSUMER(_name, _dev_name, _supply) \
static struct regulator_consumer_supply _name##_consumers[] = { \
{ \
.dev_name = _dev_name, \
.supply = _supply, \
}, \
REGULATOR_SUPPLY(_supply, _dev_name), \
}
REGULATOR_CONSUMER(ldo3, "reg-userspace-consumer.0", "vcc gps");
......
......@@ -22,6 +22,7 @@
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/input/navpoint.h>
#include <linux/lcd.h>
#include <linux/mfd/htc-egpio.h>
#include <linux/mfd/asic3.h>
......@@ -102,6 +103,10 @@ static unsigned long hx4700_pin_config[] __initdata = {
GPIO44_BTUART_CTS,
GPIO45_BTUART_RTS_LPM_LOW,
/* STUART (IRDA) */
GPIO46_STUART_RXD,
GPIO47_STUART_TXD,
/* PWM 1 (Backlight) */
GPIO17_PWM1_OUT,
......@@ -113,7 +118,7 @@ static unsigned long hx4700_pin_config[] __initdata = {
GPIO113_I2S_SYSCLK,
/* SSP 1 (NavPoint) */
GPIO23_SSP1_SCLK,
GPIO23_SSP1_SCLK_IN,
GPIO24_SSP1_SFRM,
GPIO25_SSP1_TXD,
GPIO26_SSP1_RXD,
......@@ -125,10 +130,13 @@ static unsigned long hx4700_pin_config[] __initdata = {
GPIO88_GPIO,
/* HX4700 specific input GPIOs */
GPIO12_GPIO, /* ASIC3_IRQ */
GPIO12_GPIO | WAKEUP_ON_EDGE_RISE, /* ASIC3_IRQ */
GPIO13_GPIO, /* W3220_IRQ */
GPIO14_GPIO, /* nWLAN_IRQ */
/* HX4700 specific output GPIOs */
GPIO102_GPIO | MFP_LPM_DRIVE_LOW, /* SYNAPTICS_POWER_ON */
GPIO10_GPIO, /* GSM_IRQ */
GPIO13_GPIO, /* CPLD_IRQ */
GPIO107_GPIO, /* DS1WM_IRQ */
......@@ -182,6 +190,23 @@ static struct platform_device gpio_keys = {
.id = -1,
};
/*
* Synaptics NavPoint connected to SSP1
*/
static struct navpoint_platform_data navpoint_platform_data = {
.port = 1,
.gpio = GPIO102_HX4700_SYNAPTICS_POWER_ON,
};
static struct platform_device navpoint = {
.name = "navpoint",
.id = -1,
.dev = {
.platform_data = &navpoint_platform_data,
},
};
/*
* ASIC3
*/
......@@ -227,7 +252,6 @@ static u16 asic3_gpio_config[] = {
ASIC3_GPIOC0_LED0, /* red */
ASIC3_GPIOC1_LED1, /* green */
ASIC3_GPIOC2_LED2, /* blue */
ASIC3_GPIOC4_CF_nCD,
ASIC3_GPIOC5_nCIOW,
ASIC3_GPIOC6_nCIOR,
ASIC3_GPIOC7_nPCE_1,
......@@ -241,6 +265,7 @@ static u16 asic3_gpio_config[] = {
ASIC3_GPIOC15_nPIOR,
/* GPIOD: input GPIOs, CF */
ASIC3_GPIOD4_CF_nCD,
ASIC3_GPIOD11_nCIOIS16,
ASIC3_GPIOD12_nCWAIT,
ASIC3_GPIOD15_nPIOW,
......@@ -291,6 +316,7 @@ static struct asic3_platform_data asic3_platform_data = {
.gpio_config_num = ARRAY_SIZE(asic3_gpio_config),
.irq_base = IRQ_BOARD_START,
.gpio_base = HX4700_ASIC3_GPIO_BASE,
.clock_rate = 4000000,
.leds = asic3_leds,
};
......@@ -680,12 +706,8 @@ static struct platform_device power_supply = {
*/
static struct regulator_consumer_supply bq24022_consumers[] = {
{
.supply = "vbus_draw",
},
{
.supply = "ac_draw",
},
REGULATOR_SUPPLY("vbus_draw", NULL),
REGULATOR_SUPPLY("ac_draw", NULL),
};
static struct regulator_init_data bq24022_init_data = {
......@@ -764,9 +786,8 @@ static struct platform_device strataflash = {
* Maxim MAX1587A on PI2C
*/
static struct regulator_consumer_supply max1587a_consumer = {
.supply = "vcc_core",
};
static struct regulator_consumer_supply max1587a_consumer =
REGULATOR_SUPPLY("vcc_core", NULL);
static struct regulator_init_data max1587a_v3_info = {
.constraints = {
......@@ -828,6 +849,7 @@ static struct platform_device audio = {
static struct platform_device *devices[] __initdata = {
&asic3,
&gpio_keys,
&navpoint,
&backlight,
&w3220,
&hx4700_lcd,
......@@ -859,6 +881,7 @@ static void __init hx4700_init(void)
int ret;
pxa2xx_mfp_config(ARRAY_AND_SIZE(hx4700_pin_config));
gpio_set_wake(GPIO12_HX4700_ASIC3_IRQ, 1);
ret = gpio_request_array(ARRAY_AND_SIZE(global_gpios));
if (ret)
pr_err ("hx4700: Failed to request GPIOs.\n");
......
......@@ -208,6 +208,7 @@
#define GPIO113_I2S_SYSCLK MFP_CFG_OUT(GPIO113, AF1, DRIVE_LOW)
/* SSP 1 */
#define GPIO23_SSP1_SCLK_IN MFP_CFG_IN(GPIO23, AF2)
#define GPIO23_SSP1_SCLK MFP_CFG_OUT(GPIO23, AF2, DRIVE_LOW)
#define GPIO29_SSP1_SCLK MFP_CFG_IN(GPIO29, AF3)
#define GPIO27_SSP1_SYSCLK MFP_CFG_OUT(GPIO27, AF1, DRIVE_LOW)
......
......@@ -61,6 +61,9 @@
#define GPIO93_KEY_VOLUME_UP 93
#define GPIO94_KEY_VOLUME_DOWN 94
/* Camera */
#define GPIO56_MT9M111_nOE 56
extern struct input_dev *mioa701_evdev;
extern void mioa701_gpio_lpm_set(unsigned long mfp_pin);
......
......@@ -31,7 +31,6 @@
#define PCM990_CTRL_INT_IRQ PXA_GPIO_TO_IRQ(PCM990_CTRL_INT_IRQ_GPIO)
#define PCM990_CTRL_INT_IRQ_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CTRL_PHYS PXA_CS1_PHYS /* 16-Bit */
#define PCM990_CTRL_BASE 0xea000000
#define PCM990_CTRL_SIZE (1*1024*1024)
#define PCM990_CTRL_PWR_IRQ_GPIO 14
......@@ -69,13 +68,13 @@
#define PCM990_CTRL_MMC2DE 0x0004 /* R MMC2 Card detect */
#define PCM990_CTRL_MMC2WP 0x0008 /* R MMC2 Card write protect */
#define PCM990_CTRL_REG6 0x000C /* Interrupt Clear REGISTER */
#define PCM990_CTRL_INTSETCLR 0x000C /* Interrupt Clear REGISTER */
#define PCM990_CTRL_INTC0 0x0001 /* Clear Reg BT Detect */
#define PCM990_CTRL_INTC1 0x0002 /* Clear Reg FR RI */
#define PCM990_CTRL_INTC2 0x0004 /* Clear Reg MMC1 Detect */
#define PCM990_CTRL_INTC3 0x0008 /* Clear Reg PM_5V off */
#define PCM990_CTRL_REG7 0x000E /* Interrupt Enable REGISTER */
#define PCM990_CTRL_INTMSKENA 0x000E /* Interrupt Enable REGISTER */
#define PCM990_CTRL_ENAINT0 0x0001 /* Enable Int BT Detect */
#define PCM990_CTRL_ENAINT1 0x0002 /* Enable Int FR RI */
#define PCM990_CTRL_ENAINT2 0x0004 /* Enable Int MMC1 Detect */
......@@ -102,32 +101,6 @@
#define PCM990_CTRL_ACPRES 0x0004 /* DC Present */
#define PCM990_CTRL_ACALARM 0x0008 /* Error Akku */
#define PCM990_CTRL_P2V(x) ((x) - PCM990_CTRL_PHYS + PCM990_CTRL_BASE)
#define PCM990_CTRL_V2P(x) ((x) - PCM990_CTRL_BASE + PCM990_CTRL_PHYS)
#ifndef __ASSEMBLY__
# define __PCM990_CTRL_REG(x) \
(*((volatile unsigned char *)PCM990_CTRL_P2V(x)))
#else
# define __PCM990_CTRL_REG(x) PCM990_CTRL_P2V(x)
#endif
#define PCM990_INTMSKENA __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7)
#define PCM990_INTSETCLR __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6)
#define PCM990_CTRL0 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG0)
#define PCM990_CTRL1 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG1)
#define PCM990_CTRL2 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG2)
#define PCM990_CTRL3 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3)
#define PCM990_CTRL4 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG4)
#define PCM990_CTRL5 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5)
#define PCM990_CTRL6 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG6)
#define PCM990_CTRL7 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG7)
#define PCM990_CTRL8 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG8)
#define PCM990_CTRL9 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG9)
#define PCM990_CTRL10 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG10)
#define PCM990_CTRL11 __PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG11)
/*
* IDE
*/
......@@ -166,24 +139,6 @@
#define PCM990_IDE_PLD_P2V(x) ((x) - PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_BASE)
#define PCM990_IDE_PLD_V2P(x) ((x) - PCM990_IDE_PLD_BASE + PCM990_IDE_PLD_PHYS)
#ifndef __ASSEMBLY__
# define __PCM990_IDE_PLD_REG(x) \
(*((volatile unsigned char *)PCM990_IDE_PLD_P2V(x)))
#else
# define __PCM990_IDE_PLD_REG(x) PCM990_IDE_PLD_P2V(x)
#endif
#define PCM990_IDE0 \
__PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG0)
#define PCM990_IDE1 \
__PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG1)
#define PCM990_IDE2 \
__PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG2)
#define PCM990_IDE3 \
__PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG3)
#define PCM990_IDE4 \
__PCM990_IDE_PLD_REG(PCM990_IDE_PLD_PHYS + PCM990_IDE_PLD_REG4)
/*
* Compact Flash
*/
......@@ -196,10 +151,6 @@
#define PCM990_CF_CD_EDGE IRQ_TYPE_EDGE_RISING
#define PCM990_CF_PLD_PHYS 0x30000000 /* 16 bit wide */
#define PCM990_CF_PLD_BASE 0xef000000
#define PCM990_CF_PLD_SIZE (1*1024*1024)
#define PCM990_CF_PLD_P2V(x) ((x) - PCM990_CF_PLD_PHYS + PCM990_CF_PLD_BASE)
#define PCM990_CF_PLD_V2P(x) ((x) - PCM990_CF_PLD_BASE + PCM990_CF_PLD_PHYS)
/* visible CPLD (U6) registers */
#define PCM990_CF_PLD_REG0 0x1000 /* OFFSET CF REGISTER 0 */
......@@ -239,21 +190,6 @@
#define PCM990_CF_REG6_CD1 0x0001 /* R CF Card_Detect1 */
#define PCM990_CF_REG6_CD2 0x0002 /* R CF Card_Detect2 */
#ifndef __ASSEMBLY__
# define __PCM990_CF_PLD_REG(x) \
(*((volatile unsigned char *)PCM990_CF_PLD_P2V(x)))
#else
# define __PCM990_CF_PLD_REG(x) PCM990_CF_PLD_P2V(x)
#endif
#define PCM990_CF0 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG0)
#define PCM990_CF1 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG1)
#define PCM990_CF2 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG2)
#define PCM990_CF3 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG3)
#define PCM990_CF4 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG4)
#define PCM990_CF5 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG5)
#define PCM990_CF6 __PCM990_CF_PLD_REG(PCM990_CF_PLD_PHYS + PCM990_CF_PLD_REG6)
/*
* Wolfson AC97 Touch
*/
......
......@@ -579,12 +579,8 @@ static struct platform_device power_supply = {
*/
static struct regulator_consumer_supply bq24022_consumers[] = {
{
.supply = "vbus_draw",
},
{
.supply = "ac_draw",
},
REGULATOR_SUPPLY("vbus_draw", NULL),
REGULATOR_SUPPLY("ac_draw", NULL),
};
static struct regulator_init_data bq24022_init_data = {
......
......@@ -103,6 +103,7 @@ static unsigned long mioa701_pin_config[] = {
GPIO82_CIF_DD_5,
GPIO84_CIF_FV,
GPIO85_CIF_LV,
MIO_CFG_OUT(GPIO56_MT9M111_nOE, AF0, DRIVE_LOW),
/* Bluetooth */
MIO_CFG_IN(GPIO14_BT_nACTIVITY, AF0),
......@@ -581,9 +582,7 @@ static struct wm97xx_pdata mioa701_wm97xx_pdata = {
* Voltage regulation
*/
static struct regulator_consumer_supply max1586_consumers[] = {
{
.supply = "vcc_core",
}
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data max1586_v3_info = {
......@@ -705,6 +704,7 @@ static struct gpio global_gpios[] = {
{ GPIO9_CHARGE_EN, GPIOF_OUT_INIT_HIGH, "Charger enable" },
{ GPIO18_POWEROFF, GPIOF_OUT_INIT_LOW, "Power Off" },
{ GPIO87_LCD_POWER, GPIOF_OUT_INIT_LOW, "LCD Power" },
{ GPIO56_MT9M111_nOE, GPIOF_OUT_INIT_LOW, "Camera nOE" },
};
static void __init mioa701_machine_init(void)
......
......@@ -429,9 +429,7 @@ void __init palm27x_power_init(int ac, int usb)
#if defined(CONFIG_REGULATOR_MAX1586) || \
defined(CONFIG_REGULATOR_MAX1586_MODULE)
static struct regulator_consumer_supply palm27x_max1587a_consumers[] = {
{
.supply = "vcc_core",
}
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data palm27x_max1587a_v3_info = {
......
......@@ -65,6 +65,18 @@ static unsigned long pcm990_pin_config[] __initdata = {
GPIO31_AC97_SYNC,
};
static void __iomem *pcm990_cpld_base;
static u8 pcm990_cpld_readb(unsigned int reg)
{
return readb(pcm990_cpld_base + reg);
}
static void pcm990_cpld_writeb(u8 value, unsigned int reg)
{
writeb(value, pcm990_cpld_base + reg);
}
/*
* pcm990_lcd_power - control power supply to the LCD
* @on: 0 = switch off, 1 = switch on
......@@ -78,13 +90,13 @@ static void pcm990_lcd_power(int on, struct fb_var_screeninfo *var)
/* enable LCD-Latches
* power on LCD
*/
__PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) =
PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON;
pcm990_cpld_writeb(PCM990_CTRL_LCDPWR + PCM990_CTRL_LCDON,
PCM990_CTRL_REG3);
} else {
/* disable LCD-Latches
* power off LCD
*/
__PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG3) = 0x00;
pcm990_cpld_writeb(0, PCM990_CTRL_REG3);
}
}
#endif
......@@ -243,15 +255,26 @@ static unsigned long pcm990_irq_enabled;
static void pcm990_mask_ack_irq(struct irq_data *d)
{
int pcm990_irq = (d->irq - PCM027_IRQ(0));
PCM990_INTMSKENA = (pcm990_irq_enabled &= ~(1 << pcm990_irq));
pcm990_irq_enabled &= ~(1 << pcm990_irq);
pcm990_cpld_writeb(pcm990_irq_enabled, PCM990_CTRL_INTMSKENA);
}
static void pcm990_unmask_irq(struct irq_data *d)
{
int pcm990_irq = (d->irq - PCM027_IRQ(0));
u8 val;
/* the irq can be acknowledged only if deasserted, so it's done here */
PCM990_INTSETCLR |= 1 << pcm990_irq;
PCM990_INTMSKENA = (pcm990_irq_enabled |= (1 << pcm990_irq));
pcm990_irq_enabled |= (1 << pcm990_irq);
val = pcm990_cpld_readb(PCM990_CTRL_INTSETCLR);
val |= 1 << pcm990_irq;
pcm990_cpld_writeb(val, PCM990_CTRL_INTSETCLR);
pcm990_cpld_writeb(pcm990_irq_enabled, PCM990_CTRL_INTMSKENA);
}
static struct irq_chip pcm990_irq_chip = {
......@@ -261,7 +284,10 @@ static struct irq_chip pcm990_irq_chip = {
static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
{
unsigned long pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
unsigned long pending;
pending = ~pcm990_cpld_readb(PCM990_CTRL_INTSETCLR);
pending &= pcm990_irq_enabled;
do {
/* clear our parent IRQ */
......@@ -270,7 +296,8 @@ static void pcm990_irq_handler(unsigned int irq, struct irq_desc *desc)
irq = PCM027_IRQ(0) + __ffs(pending);
generic_handle_irq(irq);
}
pending = (~PCM990_INTSETCLR) & pcm990_irq_enabled;
pending = ~pcm990_cpld_readb(PCM990_CTRL_INTSETCLR);
pending &= pcm990_irq_enabled;
} while (pending);
}
......@@ -285,8 +312,9 @@ static void __init pcm990_init_irq(void)
set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
}
PCM990_INTMSKENA = 0x00; /* disable all Interrupts */
PCM990_INTSETCLR = 0xFF;
/* disable all Interrupts */
pcm990_cpld_writeb(0x0, PCM990_CTRL_INTMSKENA);
pcm990_cpld_writeb(0xff, PCM990_CTRL_INTSETCLR);
irq_set_chained_handler(PCM990_CTRL_INT_IRQ, pcm990_irq_handler);
irq_set_irq_type(PCM990_CTRL_INT_IRQ, PCM990_CTRL_INT_IRQ_EDGE);
......@@ -309,13 +337,16 @@ static int pcm990_mci_init(struct device *dev, irq_handler_t mci_detect_int,
static void pcm990_mci_setpower(struct device *dev, unsigned int vdd)
{
struct pxamci_platform_data *p_d = dev->platform_data;
u8 val;
val = pcm990_cpld_readb(PCM990_CTRL_REG5);
if ((1 << vdd) & p_d->ocr_mask)
__PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
PCM990_CTRL_MMC2PWR;
val |= PCM990_CTRL_MMC2PWR;
else
__PCM990_CTRL_REG(PCM990_CTRL_PHYS + PCM990_CTRL_REG5) =
~PCM990_CTRL_MMC2PWR;
val &= ~PCM990_CTRL_MMC2PWR;
pcm990_cpld_writeb(PCM990_CTRL_MMC2PWR, PCM990_CTRL_REG5);
}
static void pcm990_mci_exit(struct device *dev, void *data)
......@@ -480,23 +511,6 @@ static struct platform_device pcm990_camera[] = {
};
#endif /* CONFIG_VIDEO_PXA27x ||CONFIG_VIDEO_PXA27x_MODULE */
/*
* enable generic access to the base board control CPLDs U6 and U7
*/
static struct map_desc pcm990_io_desc[] __initdata = {
{
.virtual = PCM990_CTRL_BASE,
.pfn = __phys_to_pfn(PCM990_CTRL_PHYS),
.length = PCM990_CTRL_SIZE,
.type = MT_DEVICE /* CPLD */
}, {
.virtual = PCM990_CF_PLD_BASE,
.pfn = __phys_to_pfn(PCM990_CF_PLD_PHYS),
.length = PCM990_CF_PLD_SIZE,
.type = MT_DEVICE /* CPLD */
}
};
/*
* system init for baseboard usage. Will be called by pcm027 init.
*
......@@ -507,8 +521,11 @@ void __init pcm990_baseboard_init(void)
{
pxa2xx_mfp_config(ARRAY_AND_SIZE(pcm990_pin_config));
/* register CPLD access */
iotable_init(ARRAY_AND_SIZE(pcm990_io_desc));
pcm990_cpld_base = ioremap(PCM990_CTRL_PHYS, PCM990_CTRL_SIZE);
if (!pcm990_cpld_base) {
pr_err("pcm990: failed to ioremap cpld\n");
return;
}
/* register CPLD's IRQ controller */
pcm990_init_irq();
......
......@@ -877,9 +877,7 @@ static struct i2c_board_info spitz_i2c_devs[] = {
};
static struct regulator_consumer_supply isl6271a_consumers[] = {
{
.supply = "vcc_core",
}
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data isl6271a_info[] = {
......
......@@ -151,10 +151,7 @@ static struct platform_device sht15 = {
};
static struct regulator_consumer_supply stargate2_sensor_3_con[] = {
{
.dev_name = "sht15",
.supply = "vcc",
},
REGULATOR_SUPPLY("vcc", "sht15"),
};
enum stargate2_ldos{
......
......@@ -640,9 +640,7 @@ static inline void vpac270_ide_init(void) {}
#if defined(CONFIG_REGULATOR_MAX1586) || \
defined(CONFIG_REGULATOR_MAX1586_MODULE)
static struct regulator_consumer_supply vpac270_max1587a_consumers[] = {
{
.supply = "vcc_core",
}
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data vpac270_max1587a_v3_info = {
......
......@@ -615,9 +615,7 @@ static inline void z2_spi_init(void) {}
#if defined(CONFIG_REGULATOR_TPS65023) || \
defined(CONFIG_REGULATOR_TPS65023_MODULE)
static struct regulator_consumer_supply z2_tps65021_consumers[] = {
{
.supply = "vcc_core",
}
REGULATOR_SUPPLY("vcc_core", NULL),
};
static struct regulator_init_data z2_tps65021_info[] = {
......
......@@ -290,6 +290,24 @@ static struct regulator_consumer_supply wallvdd_consumers[] = {
REGULATOR_SUPPLY("SPKVDD2", "1-001a"),
REGULATOR_SUPPLY("SPKVDDL", "1-001a"),
REGULATOR_SUPPLY("SPKVDDR", "1-001a"),
REGULATOR_SUPPLY("DC1VDD", "0-0034"),
REGULATOR_SUPPLY("DC2VDD", "0-0034"),
REGULATOR_SUPPLY("DC3VDD", "0-0034"),
REGULATOR_SUPPLY("LDO1VDD", "0-0034"),
REGULATOR_SUPPLY("LDO2VDD", "0-0034"),
REGULATOR_SUPPLY("LDO4VDD", "0-0034"),
REGULATOR_SUPPLY("LDO5VDD", "0-0034"),
REGULATOR_SUPPLY("LDO6VDD", "0-0034"),
REGULATOR_SUPPLY("LDO7VDD", "0-0034"),
REGULATOR_SUPPLY("LDO8VDD", "0-0034"),
REGULATOR_SUPPLY("LDO9VDD", "0-0034"),
REGULATOR_SUPPLY("LDO10VDD", "0-0034"),
REGULATOR_SUPPLY("LDO11VDD", "0-0034"),
REGULATOR_SUPPLY("DC1VDD", "1-0034"),
REGULATOR_SUPPLY("DC2VDD", "1-0034"),
REGULATOR_SUPPLY("DC3VDD", "1-0034"),
};
static struct regulator_init_data wallvdd_data = {
......
This diff is collapsed.
......@@ -51,7 +51,9 @@ obj-$(CONFIG_MACH_MACKEREL) += board-mackerel.o
obj-$(CONFIG_MACH_KOTA2) += board-kota2.o
obj-$(CONFIG_MACH_BONITO) += board-bonito.o
obj-$(CONFIG_MACH_MARZEN) += board-marzen.o
obj-$(CONFIG_MACH_ARMADILLO800EVA) += board-armadillo800eva.o
obj-$(CONFIG_MACH_KZM9D) += board-kzm9d.o
obj-$(CONFIG_MACH_KZM9G) += board-kzm9g.o
# Framework support
obj-$(CONFIG_SMP) += $(smp-y)
......
......@@ -997,6 +997,8 @@ static struct sh_mobile_ceu_companion csi2 = {
static struct sh_mobile_ceu_info sh_mobile_ceu_info = {
.flags = SH_CEU_FLAG_USE_8BIT_BUS,
.max_width = 8188,
.max_height = 8188,
.csi2 = &csi2,
};
......
This diff is collapsed.
......@@ -486,7 +486,7 @@ static void __init bonito_earlytimer_init(void)
shmobile_earlytimer_init();
}
void __init bonito_add_early_devices(void)
static void __init bonito_add_early_devices(void)
{
r8a7740_add_early_devices();
......
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment