Commit f6f75abc authored by Jian Shen's avatar Jian Shen Committed by David S. Miller

net: hns3: Adds support for led locate command for copper port

Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: default avatarJian Shen <shenjian15@huawei.com>
Signed-off-by: default avatarPeng Li <lipeng321@huawei.com>
Signed-off-by: default avatarSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 16b496fd
......@@ -817,21 +817,13 @@ struct hclge_reset_cmd {
#define HCLGE_NIC_CMQ_DESC_NUM 1024
#define HCLGE_NIC_CMQ_DESC_NUM_S 3
#define HCLGE_LED_PORT_SPEED_STATE_S 0
#define HCLGE_LED_PORT_SPEED_STATE_M GENMASK(5, 0)
#define HCLGE_LED_ACTIVITY_STATE_S 0
#define HCLGE_LED_ACTIVITY_STATE_M GENMASK(1, 0)
#define HCLGE_LED_LINK_STATE_S 0
#define HCLGE_LED_LINK_STATE_M GENMASK(1, 0)
#define HCLGE_LED_LOCATE_STATE_S 0
#define HCLGE_LED_LOCATE_STATE_M GENMASK(1, 0)
struct hclge_set_led_state_cmd {
u8 port_speed_led_config;
u8 link_led_config;
u8 activity_led_config;
u8 rsv1[3];
u8 locate_led_config;
u8 rsv[20];
u8 rsv2[20];
};
int hclge_cmd_init(struct hclge_dev *hdev);
......
......@@ -5991,9 +5991,7 @@ static void hclge_get_regs(struct hnae3_handle *handle, u32 *version,
"Get 64 bit register failed, ret = %d.\n", ret);
}
static int hclge_set_led_status_sfp(struct hclge_dev *hdev, u8 speed_led_status,
u8 act_led_status, u8 link_led_status,
u8 locate_led_status)
static int hclge_set_led_status(struct hclge_dev *hdev, u8 locate_led_status)
{
struct hclge_set_led_state_cmd *req;
struct hclge_desc desc;
......@@ -6002,12 +6000,6 @@ static int hclge_set_led_status_sfp(struct hclge_dev *hdev, u8 speed_led_status,
hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_LED_STATUS_CFG, false);
req = (struct hclge_set_led_state_cmd *)desc.data;
hnae_set_field(req->port_speed_led_config, HCLGE_LED_PORT_SPEED_STATE_M,
HCLGE_LED_PORT_SPEED_STATE_S, speed_led_status);
hnae_set_field(req->link_led_config, HCLGE_LED_ACTIVITY_STATE_M,
HCLGE_LED_ACTIVITY_STATE_S, act_led_status);
hnae_set_field(req->activity_led_config, HCLGE_LED_LINK_STATE_M,
HCLGE_LED_LINK_STATE_S, link_led_status);
hnae_set_field(req->locate_led_config, HCLGE_LED_LOCATE_STATE_M,
HCLGE_LED_LOCATE_STATE_S, locate_led_status);
......@@ -6028,36 +6020,17 @@ enum hclge_led_status {
static int hclge_set_led_id(struct hnae3_handle *handle,
enum ethtool_phys_id_state status)
{
#define BLINK_FREQUENCY 2
struct hclge_vport *vport = hclge_get_vport(handle);
struct hclge_dev *hdev = vport->back;
struct phy_device *phydev = hdev->hw.mac.phydev;
int ret = 0;
if (phydev || hdev->hw.mac.media_type != HNAE3_MEDIA_TYPE_FIBER)
return -EOPNOTSUPP;
switch (status) {
case ETHTOOL_ID_ACTIVE:
ret = hclge_set_led_status_sfp(hdev,
HCLGE_LED_NO_CHANGE,
HCLGE_LED_NO_CHANGE,
HCLGE_LED_NO_CHANGE,
HCLGE_LED_ON);
break;
return hclge_set_led_status(hdev, HCLGE_LED_ON);
case ETHTOOL_ID_INACTIVE:
ret = hclge_set_led_status_sfp(hdev,
HCLGE_LED_NO_CHANGE,
HCLGE_LED_NO_CHANGE,
HCLGE_LED_NO_CHANGE,
HCLGE_LED_OFF);
break;
return hclge_set_led_status(hdev, HCLGE_LED_OFF);
default:
ret = -EINVAL;
break;
return -EINVAL;
}
return ret;
}
static void hclge_get_link_mode(struct hnae3_handle *handle,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment