Commit f7777dcc authored by Ralf Baechle's avatar Ralf Baechle

MIPS: Panic messages should not end in \n.

Panic() is going to add a \n itself and it's annoying if a panic message rolls
of the screen on a device with no scrollback.
Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent 761845f0
......@@ -59,7 +59,7 @@ void __init board_setup(void)
ret = -ENODEV;
}
if (ret)
panic("cannot initialize board support\n");
panic("cannot initialize board support");
}
int __init db1235_arch_init(void)
......
......@@ -999,7 +999,7 @@ void __init plat_mem_setup(void)
if (total == 0)
panic("Unable to allocate memory from "
"cvmx_bootmem_phy_alloc\n");
"cvmx_bootmem_phy_alloc");
}
/*
......@@ -1081,7 +1081,7 @@ void __init device_tree_init(void)
/* Copy the default tree from init memory. */
initial_boot_params = early_init_dt_alloc_memory_arch(dt_size, 8);
if (initial_boot_params == NULL)
panic("Could not allocate initial_boot_params\n");
panic("Could not allocate initial_boot_params");
memcpy(initial_boot_params, fdt, dt_size);
if (do_prune) {
......
......@@ -150,7 +150,7 @@ int __init mips_cpu_intc_init(struct device_node *of_node,
domain = irq_domain_add_legacy(of_node, 8, MIPS_CPU_IRQ_BASE, 0,
&mips_cpu_intc_irq_domain_ops, NULL);
if (!domain)
panic("Failed to add irqdomain for MIPS CPU\n");
panic("Failed to add irqdomain for MIPS CPU");
return 0;
}
......
......@@ -136,10 +136,10 @@ static void bmips_prepare_cpus(unsigned int max_cpus)
{
if (request_irq(IPI0_IRQ, bmips_ipi_interrupt, IRQF_PERCPU,
"smp_ipi0", NULL))
panic("Can't request IPI0 interrupt\n");
panic("Can't request IPI0 interrupt");
if (request_irq(IPI1_IRQ, bmips_ipi_interrupt, IRQF_PERCPU,
"smp_ipi1", NULL))
panic("Can't request IPI1 interrupt\n");
panic("Can't request IPI1 interrupt");
}
/*
......
......@@ -390,7 +390,7 @@ int __init icu_of_init(struct device_node *node, struct device_node *parent)
ret = of_irq_to_resource_table(eiu_node,
ltq_eiu_irq, exin_avail);
if (ret != exin_avail)
panic("failed to load external irq resources\n");
panic("failed to load external irq resources");
if (request_mem_region(res.start, resource_size(&res),
res.name) < 0)
......
......@@ -128,7 +128,7 @@ static int pmu_enable(struct clk *clk)
do {} while (--retry && (pmu_r32(PWDSR(clk->module)) & clk->bits));
if (!retry)
panic("activating PMU module failed!\n");
panic("activating PMU module failed!");
return 0;
}
......
......@@ -245,7 +245,7 @@ static int nlm_parse_cpumask(cpumask_t *wakeup_mask)
return threadmode;
unsupp:
panic("Unsupported CPU mask %lx\n",
panic("Unsupported CPU mask %lx",
(unsigned long)cpumask_bits(wakeup_mask)[0]);
return 0;
}
......
......@@ -26,7 +26,7 @@ void ralink_clk_add(const char *dev, unsigned long rate)
struct clk *clk = kzalloc(sizeof(struct clk), GFP_KERNEL);
if (!clk)
panic("failed to add clock\n");
panic("failed to add clock");
clk->cl.dev_id = dev;
clk->cl.clk = clk;
......
......@@ -350,7 +350,7 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
name = "MT7620A";
soc_info->compatible = "ralink,mt7620a-soc";
} else {
panic("mt7620: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
panic("mt7620: unknown SoC, n0:%08x n1:%08x", n0, n1);
}
rev = __raw_readl(sysc + SYSC_REG_CHIP_REV);
......
......@@ -108,7 +108,7 @@ static int __init plat_of_setup(void)
strncpy(of_ids[1].compatible, "palmbus", len);
if (of_platform_populate(NULL, of_ids, NULL, NULL))
panic("failed to populate DT\n");
panic("failed to populate DT");
/* make sure ithat the reset controller is setup early */
ralink_rst_init();
......
......@@ -276,7 +276,7 @@ void prom_soc_init(struct ralink_soc_info *soc_info)
name = "RT5350";
soc_info->compatible = "ralink,rt5350-soc";
} else {
panic("rt305x: unknown SoC, n0:%08x n1:%08x\n", n0, n1);
panic("rt305x: unknown SoC, n0:%08x n1:%08x", n0, n1);
}
id = __raw_readl(sysc + SYSC_REG_CHIP_ID);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment