Commit f88359e1 authored by Yu Chen's avatar Yu Chen Committed by Greg Kroah-Hartman

usb: dwc3: core: Do core softreset when switch mode

From: John Stultz <john.stultz@linaro.org>

According to the programming guide, to switch mode for DRD controller,
the driver needs to do the following.

To switch from device to host:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(host mode)
3. Reset the host with USBCMD.HCRESET
4. Then follow up with the initializing host registers sequence

To switch from host to device:
1. Reset controller with GCTL.CoreSoftReset
2. Set GCTL.PrtCapDir(device mode)
3. Reset the device with DCTL.CSftRst
4. Then follow up with the initializing registers sequence

Currently we're missing step 1) to do GCTL.CoreSoftReset and step 3) of
switching from host to device. John Stult reported a lockup issue seen
with HiKey960 platform without these steps[1]. Similar issue is observed
with Ferry's testing platform[2].

So, apply the required steps along with some fixes to Yu Chen's and John
Stultz's version. The main fixes to their versions are the missing wait
for clocks synchronization before clearing GCTL.CoreSoftReset and only
apply DCTL.CSftRst when switching from host to device.

[1] https://lore.kernel.org/linux-usb/20210108015115.27920-1-john.stultz@linaro.org/
[2] https://lore.kernel.org/linux-usb/0ba7a6ba-e6a7-9cd4-0695-64fc927e01f1@gmail.com/

Fixes: 41ce1456 ("usb: dwc3: core: make dwc3_set_mode() work properly")
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Wesley Cheng <wcheng@codeaurora.org>
Cc: <stable@vger.kernel.org>
Tested-by: default avatarJohn Stultz <john.stultz@linaro.org>
Tested-by: default avatarWesley Cheng <wcheng@codeaurora.org>
Signed-off-by: default avatarYu Chen <chenyu56@huawei.com>
Signed-off-by: default avatarJohn Stultz <john.stultz@linaro.org>
Signed-off-by: default avatarThinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/374440f8dcd4f06c02c2caf4b1efde86774e02d9.1618521663.git.Thinh.Nguyen@synopsys.comSigned-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent 0fdf3c5e
......@@ -114,6 +114,8 @@ void dwc3_set_prtcap(struct dwc3 *dwc, u32 mode)
dwc->current_dr_role = mode;
}
static int dwc3_core_soft_reset(struct dwc3 *dwc);
static void __dwc3_set_mode(struct work_struct *work)
{
struct dwc3 *dwc = work_to_dwc(work);
......@@ -121,6 +123,8 @@ static void __dwc3_set_mode(struct work_struct *work)
int ret;
u32 reg;
mutex_lock(&dwc->mutex);
pm_runtime_get_sync(dwc->dev);
if (dwc->current_dr_role == DWC3_GCTL_PRTCAP_OTG)
......@@ -154,6 +158,25 @@ static void __dwc3_set_mode(struct work_struct *work)
break;
}
/* For DRD host or device mode only */
if (dwc->desired_dr_role != DWC3_GCTL_PRTCAP_OTG) {
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg |= DWC3_GCTL_CORESOFTRESET;
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
/*
* Wait for internal clocks to synchronized. DWC_usb31 and
* DWC_usb32 may need at least 50ms (less for DWC_usb3). To
* keep it consistent across different IPs, let's wait up to
* 100ms before clearing GCTL.CORESOFTRESET.
*/
msleep(100);
reg = dwc3_readl(dwc->regs, DWC3_GCTL);
reg &= ~DWC3_GCTL_CORESOFTRESET;
dwc3_writel(dwc->regs, DWC3_GCTL, reg);
}
spin_lock_irqsave(&dwc->lock, flags);
dwc3_set_prtcap(dwc, dwc->desired_dr_role);
......@@ -178,6 +201,8 @@ static void __dwc3_set_mode(struct work_struct *work)
}
break;
case DWC3_GCTL_PRTCAP_DEVICE:
dwc3_core_soft_reset(dwc);
dwc3_event_buffers_setup(dwc);
if (dwc->usb2_phy)
......@@ -200,6 +225,7 @@ static void __dwc3_set_mode(struct work_struct *work)
out:
pm_runtime_mark_last_busy(dwc->dev);
pm_runtime_put_autosuspend(dwc->dev);
mutex_unlock(&dwc->mutex);
}
void dwc3_set_mode(struct dwc3 *dwc, u32 mode)
......@@ -1553,6 +1579,7 @@ static int dwc3_probe(struct platform_device *pdev)
dwc3_cache_hwparams(dwc);
spin_lock_init(&dwc->lock);
mutex_init(&dwc->mutex);
pm_runtime_set_active(dev);
pm_runtime_use_autosuspend(dev);
......
......@@ -13,6 +13,7 @@
#include <linux/device.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
#include <linux/ioport.h>
#include <linux/list.h>
#include <linux/bitops.h>
......@@ -947,6 +948,7 @@ struct dwc3_scratchpad_array {
* @scratch_addr: dma address of scratchbuf
* @ep0_in_setup: one control transfer is completed and enter setup phase
* @lock: for synchronizing
* @mutex: for mode switching
* @dev: pointer to our struct device
* @sysdev: pointer to the DMA-capable device
* @xhci: pointer to our xHCI child
......@@ -1088,6 +1090,9 @@ struct dwc3 {
/* device lock */
spinlock_t lock;
/* mode switching lock */
struct mutex mutex;
struct device *dev;
struct device *sysdev;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment