ARM: dts: sbc-t3x: use omap specific pinctrl defines

Use omap specific pinctrl defines (OMAP3_CORE1_IOPAD) to configure
the padconf register offset.

This simplify further support of CompuLab's boards based on omap36xx,
omap34xx and am35x.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/boot/dts/omap3-cm-t3730.dts

@@ -34,44 +34,44 @@ wl12xx_vaux2: wl12xx_vaux2 {
 &omap3_pmx_core {
 	mmc1_pins: pinmux_mmc1_pins {
 		pinctrl-single,pins = <
-			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
-			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
-			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
-			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
-			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
-			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
+			OMAP3_CORE1_IOPAD(0x2144, PIN_OUTPUT_PULLUP | MUX_MODE0)/* sdmmc1_clk.sdmmc1_clk */
+			OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */
+			OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */
+			OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */
+			OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */
 		>;
 	};
 
 	mmc2_pins: pinmux_mmc2_pins {
 		pinctrl-single,pins = <
-			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
-			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
-			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
-			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
-			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
-			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+			OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
 		>;
 	};
 
 	smsc1_pins: pinmux_smsc1_pins {
 		pinctrl-single,pins = <
-			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
-			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
+			OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs5.gpmc_ncs5 */
+			OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
 		>;
 	};
 
 	uart3_pins: pinmux_uart3_pins {
 		pinctrl-single,pins = <
-			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
-			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+			OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0)	/* uart3_rx_irrx.uart3_rx_irrx */
+			OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0)	/* uart3_tx_irtx.uart3_tx_irtx */
 		>;
 	};
 
 	wl12xx_gpio: pinmux_wl12xx_gpio {
 		pinctrl-single,pins = <
-			0xb2 (PIN_OUTPUT | MUX_MODE4)		/* dss_data3.gpio_73 */
-			0x134 (PIN_INPUT | MUX_MODE4)		/* sdmmc2_dat4.gpio_136 */
+			OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4)	/* dss_data3.gpio_73 */
+			OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4)	/* sdmmc2_dat4.gpio_136 */
 		>;
 	};
 };

arch/arm/boot/dts/omap3-sbc-t3730.dts

@@ -23,8 +23,8 @@ &smsc2 {
 &omap3_pmx_core {
 	smsc2_pins: pinmux_smsc2_pins {
 		pinctrl-single,pins = <
-			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
-			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+			OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0)	/* gpmc_ncs4.gpmc_ncs4 */
+			OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
 		>;
 	};
-};
\ No newline at end of file
+};