Commit fc57d783 authored by Michael Riesch's avatar Michael Riesch Committed by Heiko Stuebner

arm64: dts: rockchip: rk3568-evb1-v10: add ethernet support

Signed-off-by: default avatarMichael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20210729093913.8917-3-michael.riesch@wolfvision.netSigned-off-by: default avatarHeiko Stuebner <heiko@sntech.de>
parent b8d41e50
......@@ -13,6 +13,11 @@ / {
model = "Rockchip RK3568 EVB1 DDR4 V10 Board";
compatible = "rockchip,rk3568-evb1-v10", "rockchip,rk3568";
aliases {
ethernet0 = &gmac0;
ethernet1 = &gmac1;
};
chosen: chosen {
stdout-path = "serial2:1500000n8";
};
......@@ -67,6 +72,58 @@ regulator-state-mem {
};
};
&gmac0 {
assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
assigned-clock-rates = <0>, <125000000>;
clock_in_out = "output";
phy-handle = <&rgmii_phy0>;
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&gmac0_miim
&gmac0_tx_bus2
&gmac0_rx_bus2
&gmac0_rgmii_clk
&gmac0_rgmii_bus>;
status = "okay";
};
&gmac1 {
assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
assigned-clock-rates = <0>, <125000000>;
clock_in_out = "output";
phy-handle = <&rgmii_phy1>;
phy-mode = "rgmii-id";
pinctrl-names = "default";
pinctrl-0 = <&gmac1m1_miim
&gmac1m1_tx_bus2
&gmac1m1_rx_bus2
&gmac1m1_rgmii_clk
&gmac1m1_rgmii_bus>;
status = "okay";
};
&mdio0 {
rgmii_phy0: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0x0>;
reset-assert-us = <20000>;
reset-deassert-us = <100000>;
reset-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_LOW>;
};
};
&mdio1 {
rgmii_phy1: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c22";
reg = <0x0>;
reset-assert-us = <20000>;
reset-deassert-us = <100000>;
reset-gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_LOW>;
};
};
&sdhci {
bus-width = <8>;
max-frequency = <200000000>;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment