arm64: dts: qcom: qcs6490-rb3gen2: enable hdmi bridge

Rb3Gen2 has a lt9611uxc DSI-to-HDMI bridge on i2c0, with
reset gpio from pm7250b gpio2 and irq gpio from tlmm gpio24.
Bridge supplies are Vdd connected to input supply directly
and vcc to L11c. Enable HDMI output, bridge and corresponding
DSI output.
Signed-off-by: Venkata Prahlad Valluru <quic_vvalluru@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240528141954.7567-1-quic_vvalluru@quicinc.comSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts

@@ -52,6 +52,25 @@ dp_connector_in: endpoint {
 		};
 	};
 
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
+	lt9611_1v2: lt9611-vdd12-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
 	reserved-memory {
 		xbl_mem: xbl@80700000 {
 			reg = <0x0 0x80700000 0x0 0x100000>;
@@ -538,6 +557,46 @@ &gpi_dma1 {
 	status = "okay";
 };
 
+&i2c0 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+
+		interrupts-extended = <&tlmm 24 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&pm7250b_gpios 2 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&vreg_l11c_2p8>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
 &i2c1 {
 	status = "okay";
 
@@ -595,6 +654,21 @@ &mdss_dp_out {
 	remote-endpoint = <&usb_dp_qmpphy_dp_in>;
 };
 
+&mdss_dsi {
+	vdda-supply = <&vreg_l6b_1p2>;
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&lt9611_a>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi_phy {
+	vdds-supply = <&vreg_l10c_0p88>;
+	status = "okay";
+};
+
 &mdss_edp {
 	status = "okay";
 };
@@ -726,3 +800,23 @@ &edp_hot_plug_det {
 	function = "gpio";
 	bias-disable;
 };
+
+&pm7250b_gpios {
+	lt9611_rst_pin: lt9611-rst-state {
+		pins = "gpio2";
+		function = "normal";
+
+		output-high;
+		input-disable;
+		power-source = <0>;
+	};
+};
+
+&tlmm {
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio24";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};