Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6: (41 commits)
  regulator: Add some brief design documentation
  regulator: fix voltage range in da9034 ldo12
  regulator/driver: be more specific in nanodoc for is_enabled
  regulator/lp3971: drop unnecessary initialization
  regulator: drop 'default n'
  regulator: fix typos
  regulator: fix calculation of voltage range in da9034_set_ldo12_voltage()
  regulator: update a filename in documentation
  drivers/regulator/Kconfig: fix typo (s/Usersapce/Userspace/) in REGULATOR_USERSPACE_CONSUMER description
  REGULATOR Handle positive returncode from enable
  regulator: tps650xx - build fixes for x86_64
  Fix some regulator documentation
  Regulator: Adding TPS65023 and TPS6507x in Kconfig and Makefile
  Regulator: Add TPS6507x regulator driver
  Regulator: Add TPS65023 regulator driver
  regulator: userspace: use sysfs_create_group
  regulator: Add GPIO enable control to fixed voltage regulator driver
  Regulator: Implement list_voltage for pcf50633 regulator driver.
  regulator: regulator_enable() permission checking
  regulator: Push locking for regulator_is_enabled() out
  ...

Documentation/power/regulator/design.txt

+Regulator API design notes
+==========================
+
+This document provides a brief, partially structured, overview of some
+of the design considerations which impact the regulator API design.
+
+Safety
+------
+
+ - Errors in regulator configuration can have very serious consequences
+   for the system, potentially including lasting hardware damage.
+ - It is not possible to automatically determine the power confugration
+   of the system - software-equivalent variants of the same chip may
+   have different power requirments, and not all components with power
+   requirements are visible to software.
+
+  => The API should make no changes to the hardware state unless it has
+     specific knowledge that these changes are safe to do perform on
+     this particular system.
+
+Consumer use cases
+------------------
+
+ - The overwhelming majority of devices in a system will have no
+   requirement to do any runtime configuration of their power beyond
+   being able to turn it on or off.
+
+ - Many of the power supplies in the system will be shared between many
+   different consumers.
+
+  => The consumer API should be structured so that these use cases are
+     very easy to handle and so that consumers will work with shared
+     supplies without any additional effort.

Documentation/power/regulator/machine.txt

@@ -87,7 +87,7 @@ static struct platform_device regulator_devices[] = {
 },
 };
 /* register regulator 1 device */
-platform_device_register(&wm8350_regulator_devices[0]);
+platform_device_register(&regulator_devices[0]);
 
 /* register regulator 2 device */
-platform_device_register(&wm8350_regulator_devices[1]);
+platform_device_register(&regulator_devices[1]);

Documentation/power/regulator/overview.txt

@@ -29,7 +29,7 @@ Some terms used in this document:-
 
 
   o PMIC         - Power Management IC. An IC that contains numerous regulators
-                   and often contains other susbsystems.
+                   and often contains other subsystems.
 
 
   o Consumer     - Electronic device that is supplied power by a regulator.
@@ -168,4 +168,4 @@ relevant to non SoC devices and is split into the following four interfaces:-
       userspace via sysfs. This could be used to help monitor device power
       consumption and status.
 
-        See Documentation/ABI/testing/regulator-sysfs.txt
+        See Documentation/ABI/testing/sysfs-class-regulator

Documentation/power/regulator/regulator.txt

@@ -10,8 +10,9 @@ Registration
 
 Drivers can register a regulator by calling :-
 
-struct regulator_dev *regulator_register(struct device *dev,
-	struct regulator_desc *regulator_desc);
+struct regulator_dev *regulator_register(struct regulator_desc *regulator_desc,
+	struct device *dev, struct regulator_init_data *init_data,
+	void *driver_data);
 
 This will register the regulators capabilities and operations to the regulator
 core.

drivers/regulator/Kconfig

 menuconfig REGULATOR
 	bool "Voltage and Current Regulator Support"
-	default n
 	help
 	  Generic Voltage and Current Regulator support.
 
@@ -30,7 +29,6 @@ config REGULATOR_DEBUG
 
 config REGULATOR_FIXED_VOLTAGE
 	tristate "Fixed voltage regulator support"
-	default n
 	help
 	  This driver provides support for fixed voltage regulators,
 	  useful for systems which use a combination of software
@@ -38,7 +36,6 @@ config REGULATOR_FIXED_VOLTAGE
 
 config REGULATOR_VIRTUAL_CONSUMER
 	tristate "Virtual regulator consumer support"
-	default n
 	help
 	  This driver provides a virtual consumer for the voltage and
           current regulator API which provides sysfs controls for
@@ -49,17 +46,15 @@ config REGULATOR_VIRTUAL_CONSUMER
 
 config REGULATOR_USERSPACE_CONSUMER
 	tristate "Userspace regulator consumer support"
-	default n
 	help
 	  There are some classes of devices that are controlled entirely
-	  from user space. Usersapce consumer driver provides ability to
+	  from user space. Userspace consumer driver provides ability to
 	  control power supplies for such devices.
 
           If unsure, say no.
 
 config REGULATOR_BQ24022
 	tristate "TI bq24022 Dual Input 1-Cell Li-Ion Charger IC"
-	default n
 	help
 	  This driver controls a TI bq24022 Charger attached via
 	  GPIOs. The provided current regulator can enable/disable
@@ -69,7 +64,6 @@ config REGULATOR_BQ24022
 config REGULATOR_MAX1586
 	tristate "Maxim 1586/1587 voltage regulator"
 	depends on I2C
-	default n
 	help
 	  This driver controls a Maxim 1586 or 1587 voltage output
 	  regulator via I2C bus. The provided regulator is suitable
@@ -147,5 +141,21 @@ config REGULATOR_AB3100
 	 AB3100 analog baseband dealing with power regulators
 	 for the system.
 
+config REGULATOR_TPS65023
+	tristate "TI TPS65023 Power regulators"
+	depends on I2C
+	help
+	  This driver supports TPS65023 voltage regulator chips. TPS65023 provides
+	  three step-down converters and two general-purpose LDO voltage regulators.
+	  It supports TI's software based Class-2 SmartReflex implementation.
+
+config REGULATOR_TPS6507X
+	tristate "TI TPS6507X Power regulators"
+	depends on I2C
+	help
+	  This driver supports TPS6507X voltage regulator chips. TPS6507X provides
+	  three step-down converters and two general-purpose LDO voltage regulators.
+	  It supports TI's software based Class-2 SmartReflex implementation.
+
 endif
 

drivers/regulator/Makefile

@@ -23,4 +23,7 @@ obj-$(CONFIG_REGULATOR_PCAP) += pcap-regulator.o
 obj-$(CONFIG_REGULATOR_MC13783) += mc13783.o
 obj-$(CONFIG_REGULATOR_AB3100) += ab3100.o
 
+obj-$(CONFIG_REGULATOR_TPS65023) += tps65023-regulator.o
+obj-$(CONFIG_REGULATOR_TPS6507X) += tps6507x-regulator.o
+
 ccflags-$(CONFIG_REGULATOR_DEBUG) += -DDEBUG

drivers/regulator/da903x.c

@@ -64,6 +64,14 @@
 #define DA9034_MDTV2		(0x33)
 #define DA9034_MVRC		(0x34)
 
+/* DA9035 Registers. DA9034 Registers are comptabile to DA9035. */
+#define DA9035_OVER3		(0x12)
+#define DA9035_VCC2		(0x1f)
+#define DA9035_3DTV1		(0x2c)
+#define DA9035_3DTV2		(0x2d)
+#define DA9035_3VRC		(0x2e)
+#define DA9035_AUTOSKIP		(0x2f)
+
 struct da903x_regulator_info {
 	struct regulator_desc desc;
 
@@ -79,6 +87,10 @@ struct da903x_regulator_info {
 	int	enable_bit;
 };
 
+static int da9034_ldo12_data[] = { 1700, 1750, 1800, 1850, 1900, 1950,
+				   2000, 2050, 2700, 2750, 2800, 2850,
+				   2900, 2950, 3000, 3050 };
+
 static inline struct device *to_da903x_dev(struct regulator_dev *rdev)
 {
 	return rdev_get_dev(rdev)->parent->parent;
@@ -162,6 +174,17 @@ static int da903x_is_enabled(struct regulator_dev *rdev)
 	return !!(reg_val & (1 << info->enable_bit));
 }
 
+static int da903x_list_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+	struct da903x_regulator_info *info = rdev_get_drvdata(rdev);
+	int ret;
+
+	ret = info->min_uV + info->step_uV * selector;
+	if (ret > info->max_uV)
+		return -EINVAL;
+	return ret;
+}
+
 /* DA9030 specific operations */
 static int da9030_set_ldo1_15_voltage(struct regulator_dev *rdev,
 				       int min_uV, int max_uV)
@@ -278,7 +301,7 @@ static int da9034_set_ldo12_voltage(struct regulator_dev *rdev,
 	}
 
 	val = (min_uV - info->min_uV + info->step_uV - 1) / info->step_uV;
-	val = (val > 7 || val < 20) ? 8 : val - 12;
+	val = (val >= 20) ? val - 12 : ((val > 7) ? 8 : val);
 	val <<= info->vol_shift;
 	mask = ((1 << info->vol_nbits) - 1)  << info->vol_shift;
 
@@ -305,9 +328,18 @@ static int da9034_get_ldo12_voltage(struct regulator_dev *rdev)
 	return info->min_uV + info->step_uV * val;
 }
 
+static int da9034_list_ldo12_voltage(struct regulator_dev *rdev,
+				     unsigned selector)
+{
+	if (selector > ARRAY_SIZE(da9034_ldo12_data))
+		return -EINVAL;
+	return da9034_ldo12_data[selector] * 1000;
+}
+
 static struct regulator_ops da903x_regulator_ldo_ops = {
 	.set_voltage	= da903x_set_ldo_voltage,
 	.get_voltage	= da903x_get_voltage,
+	.list_voltage	= da903x_list_voltage,
 	.enable		= da903x_enable,
 	.disable	= da903x_disable,
 	.is_enabled	= da903x_is_enabled,
@@ -317,6 +349,7 @@ static struct regulator_ops da903x_regulator_ldo_ops = {
 static struct regulator_ops da9030_regulator_ldo14_ops = {
 	.set_voltage	= da9030_set_ldo14_voltage,
 	.get_voltage	= da9030_get_ldo14_voltage,
+	.list_voltage	= da903x_list_voltage,
 	.enable		= da903x_enable,
 	.disable	= da903x_disable,
 	.is_enabled	= da903x_is_enabled,
@@ -326,6 +359,7 @@ static struct regulator_ops da9030_regulator_ldo14_ops = {
 static struct regulator_ops da9030_regulator_ldo1_15_ops = {
 	.set_voltage	= da9030_set_ldo1_15_voltage,
 	.get_voltage	= da903x_get_voltage,
+	.list_voltage	= da903x_list_voltage,
 	.enable		= da903x_enable,
 	.disable	= da903x_disable,
 	.is_enabled	= da903x_is_enabled,
@@ -334,6 +368,7 @@ static struct regulator_ops da9030_regulator_ldo1_15_ops = {
 static struct regulator_ops da9034_regulator_dvc_ops = {
 	.set_voltage	= da9034_set_dvc_voltage,
 	.get_voltage	= da903x_get_voltage,
+	.list_voltage	= da903x_list_voltage,
 	.enable		= da903x_enable,
 	.disable	= da903x_disable,
 	.is_enabled	= da903x_is_enabled,
@@ -343,6 +378,7 @@ static struct regulator_ops da9034_regulator_dvc_ops = {
 static struct regulator_ops da9034_regulator_ldo12_ops = {
 	.set_voltage	= da9034_set_ldo12_voltage,
 	.get_voltage	= da9034_get_ldo12_voltage,
+	.list_voltage	= da9034_list_ldo12_voltage,
 	.enable		= da903x_enable,
 	.disable	= da903x_disable,
 	.is_enabled	= da903x_is_enabled,
@@ -355,6 +391,7 @@ static struct regulator_ops da9034_regulator_ldo12_ops = {
 		.ops	= &da903x_regulator_ldo_ops,			\
 		.type	= REGULATOR_VOLTAGE,				\
 		.id	= _pmic##_ID_LDO##_id,				\
+		.n_voltages = (step) ? ((max - min) / step + 1) : 1,	\
 		.owner	= THIS_MODULE,					\
 	},								\
 	.min_uV		= (min) * 1000,					\
@@ -367,24 +404,25 @@ static struct regulator_ops da9034_regulator_ldo12_ops = {
 	.enable_bit	= (ebit),					\
 }
 
-#define DA9034_DVC(_id, min, max, step, vreg, nbits, ureg, ubit, ereg, ebit) \
+#define DA903x_DVC(_pmic, _id, min, max, step, vreg, nbits, ureg, ubit, ereg, ebit) \
 {									\
 	.desc	= {							\
 		.name	= #_id,						\
 		.ops	= &da9034_regulator_dvc_ops,			\
 		.type	= REGULATOR_VOLTAGE,				\
-		.id	= DA9034_ID_##_id,				\
+		.id	= _pmic##_ID_##_id,				\
+		.n_voltages = (step) ? ((max - min) / step + 1) : 1,	\
 		.owner	= THIS_MODULE,					\
 	},								\
 	.min_uV		= (min) * 1000,					\
 	.max_uV		= (max) * 1000,					\
 	.step_uV	= (step) * 1000,				\
-	.vol_reg	= DA9034_##vreg,				\
+	.vol_reg	= _pmic##_##vreg,				\
 	.vol_shift	= (0),						\
 	.vol_nbits	= (nbits),					\
-	.update_reg	= DA9034_##ureg,				\
+	.update_reg	= _pmic##_##ureg,				\
 	.update_bit	= (ubit),					\
-	.enable_reg	= DA9034_##ereg,				\
+	.enable_reg	= _pmic##_##ereg,				\
 	.enable_bit	= (ebit),					\
 }
 
@@ -394,8 +432,22 @@ static struct regulator_ops da9034_regulator_ldo12_ops = {
 #define DA9030_LDO(_id, min, max, step, vreg, shift, nbits, ereg, ebit)	\
 	DA903x_LDO(DA9030, _id, min, max, step, vreg, shift, nbits, ereg, ebit)
 
+#define DA9030_DVC(_id, min, max, step, vreg, nbits, ureg, ubit, ereg, ebit) \
+	DA903x_DVC(DA9030, _id, min, max, step, vreg, nbits, ureg, ubit, \
+		   ereg, ebit)
+
+#define DA9034_DVC(_id, min, max, step, vreg, nbits, ureg, ubit, ereg, ebit) \
+	DA903x_DVC(DA9034, _id, min, max, step, vreg, nbits, ureg, ubit, \
+		   ereg, ebit)
+
+#define DA9035_DVC(_id, min, max, step, vreg, nbits, ureg, ubit, ereg, ebit) \
+	DA903x_DVC(DA9035, _id, min, max, step, vreg, nbits, ureg, ubit, \
+		   ereg, ebit)
+
 static struct da903x_regulator_info da903x_regulator_info[] = {
 	/* DA9030 */
+	DA9030_DVC(BUCK2, 850, 1625, 25, BUCK2DVM1, 5, BUCK2DVM1, 7, RCTL11, 0),
+
 	DA9030_LDO( 1, 1200, 3200, 100,    LDO1, 0, 5, RCTL12, 1),
 	DA9030_LDO( 2, 1800, 3200, 100,   LDO23, 0, 4, RCTL12, 2),
 	DA9030_LDO( 3, 1800, 3200, 100,   LDO23, 4, 4, RCTL12, 3),
@@ -417,9 +469,9 @@ static struct da903x_regulator_info da903x_regulator_info[] = {
 	DA9030_LDO(13, 2100, 2100, 0, INVAL, 0, 0, RCTL11, 3), /* fixed @2.1V */
 
 	/* DA9034 */
-	DA9034_DVC(BUCK1, 725, 1500, 25, ADTV1, 5, VCC1, 0, OVER1, 0),
-	DA9034_DVC(BUCK2, 725, 1500, 25, CDTV1, 5, VCC1, 2, OVER1, 1),
-	DA9034_DVC(LDO2,  725, 1500, 25, SDTV1, 5, VCC1, 4, OVER1, 2),
+	DA9034_DVC(BUCK1, 725, 1500, 25, ADTV2, 5, VCC1, 0, OVER1, 0),
+	DA9034_DVC(BUCK2, 725, 1500, 25, CDTV2, 5, VCC1, 2, OVER1, 1),
+	DA9034_DVC(LDO2,  725, 1500, 25, SDTV2, 5, VCC1, 4, OVER1, 2),
 	DA9034_DVC(LDO1, 1700, 2075, 25, MDTV1, 4, VCC1, 6, OVER3, 4),
 
 	DA9034_LDO( 3, 1800, 3300, 100,  LDO643, 0, 4, OVER3, 5),
@@ -435,6 +487,9 @@ static struct da903x_regulator_info da903x_regulator_info[] = {
 	DA9034_LDO(14, 1800, 3300, 100, LDO1514, 0, 4, OVER3, 0),
 	DA9034_LDO(15, 1800, 3300, 100, LDO1514, 4, 4, OVER3, 1),
 	DA9034_LDO(5, 3100, 3100, 0, INVAL, 0, 0, OVER3, 7), /* fixed @3.1V */
+
+	/* DA9035 */
+	DA9035_DVC(BUCK3, 1800, 2200, 100, 3DTV1, 3, VCC2, 0, OVER3, 3),
 };
 
 static inline struct da903x_regulator_info *find_regulator_info(int id)
@@ -462,8 +517,10 @@ static int __devinit da903x_regulator_probe(struct platform_device *pdev)
 	}
 
 	/* Workaround for the weird LDO12 voltage setting */
-	if (ri->desc.id == DA9034_ID_LDO12)
+	if (ri->desc.id == DA9034_ID_LDO12) {
 		ri->desc.ops = &da9034_regulator_ldo12_ops;
+		ri->desc.n_voltages = ARRAY_SIZE(da9034_ldo12_data);
+	}
 
 	if (ri->desc.id == DA9030_ID_LDO14)
 		ri->desc.ops = &da9030_regulator_ldo14_ops;

drivers/regulator/fixed.c

@@ -5,6 +5,9 @@
  *
  * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
  *
+ * Copyright (c) 2009 Nokia Corporation
+ * Roger Quadros <ext-roger.quadros@nokia.com>
+ *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of the
@@ -20,20 +23,45 @@
 #include <linux/platform_device.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/fixed.h>
+#include <linux/gpio.h>
 
 struct fixed_voltage_data {
 	struct regulator_desc desc;
 	struct regulator_dev *dev;
 	int microvolts;
+	int gpio;
+	unsigned enable_high:1;
+	unsigned is_enabled:1;
 };
 
 static int fixed_voltage_is_enabled(struct regulator_dev *dev)
 {
-	return 1;
+	struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+	return data->is_enabled;
 }
 
 static int fixed_voltage_enable(struct regulator_dev *dev)
 {
+	struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+	if (gpio_is_valid(data->gpio)) {
+		gpio_set_value_cansleep(data->gpio, data->enable_high);
+		data->is_enabled = 1;
+	}
+
+	return 0;
+}
+
+static int fixed_voltage_disable(struct regulator_dev *dev)
+{
+	struct fixed_voltage_data *data = rdev_get_drvdata(dev);
+
+	if (gpio_is_valid(data->gpio)) {
+		gpio_set_value_cansleep(data->gpio, !data->enable_high);
+		data->is_enabled = 0;
+	}
+
 	return 0;
 }
 
@@ -58,6 +86,7 @@ static int fixed_voltage_list_voltage(struct regulator_dev *dev,
 static struct regulator_ops fixed_voltage_ops = {
 	.is_enabled = fixed_voltage_is_enabled,
 	.enable = fixed_voltage_enable,
+	.disable = fixed_voltage_disable,
 	.get_voltage = fixed_voltage_get_voltage,
 	.list_voltage = fixed_voltage_list_voltage,
 };
@@ -70,12 +99,14 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
 
 	drvdata = kzalloc(sizeof(struct fixed_voltage_data), GFP_KERNEL);
 	if (drvdata == NULL) {
+		dev_err(&pdev->dev, "Failed to allocate device data\n");
 		ret = -ENOMEM;
 		goto err;
 	}
 
 	drvdata->desc.name = kstrdup(config->supply_name, GFP_KERNEL);
 	if (drvdata->desc.name == NULL) {
+		dev_err(&pdev->dev, "Failed to allocate supply name\n");
 		ret = -ENOMEM;
 		goto err;
 	}
@@ -85,12 +116,62 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
 	drvdata->desc.n_voltages = 1;
 
 	drvdata->microvolts = config->microvolts;
+	drvdata->gpio = config->gpio;
+
+	if (gpio_is_valid(config->gpio)) {
+		drvdata->enable_high = config->enable_high;
+
+		/* FIXME: Remove below print warning
+		 *
+		 * config->gpio must be set to -EINVAL by platform code if
+		 * GPIO control is not required. However, early adopters
+		 * not requiring GPIO control may forget to initialize
+		 * config->gpio to -EINVAL. This will cause GPIO 0 to be used
+		 * for GPIO control.
+		 *
+		 * This warning will be removed once there are a couple of users
+		 * for this driver.
+		 */
+		if (!config->gpio)
+			dev_warn(&pdev->dev,
+				"using GPIO 0 for regulator enable control\n");
+
+		ret = gpio_request(config->gpio, config->supply_name);
+		if (ret) {
+			dev_err(&pdev->dev,
+			   "Could not obtain regulator enable GPIO %d: %d\n",
+							config->gpio, ret);
+			goto err_name;
+		}
+
+		/* set output direction without changing state
+		 * to prevent glitch
+		 */
+		drvdata->is_enabled = config->enabled_at_boot;
+		ret = drvdata->is_enabled ?
+				config->enable_high : !config->enable_high;
+
+		ret = gpio_direction_output(config->gpio, ret);
+		if (ret) {
+			dev_err(&pdev->dev,
+			   "Could not configure regulator enable GPIO %d direction: %d\n",
+							config->gpio, ret);
+			goto err_gpio;
+		}
+
+	} else {
+		/* Regulator without GPIO control is considered
+		 * always enabled
+		 */
+		drvdata->is_enabled = 1;
+	}
 
 	drvdata->dev = regulator_register(&drvdata->desc, &pdev->dev,
 					  config->init_data, drvdata);
 	if (IS_ERR(drvdata->dev)) {
 		ret = PTR_ERR(drvdata->dev);
-		goto err_name;
+		dev_err(&pdev->dev, "Failed to register regulator: %d\n", ret);
+		goto err_gpio;
 	}
 
 	platform_set_drvdata(pdev, drvdata);
@@ -100,6 +181,9 @@ static int regulator_fixed_voltage_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_gpio:
+	if (gpio_is_valid(config->gpio))
+		gpio_free(config->gpio);
 err_name:
 	kfree(drvdata->desc.name);
 err:
@@ -115,6 +199,9 @@ static int regulator_fixed_voltage_remove(struct platform_device *pdev)
 	kfree(drvdata->desc.name);
 	kfree(drvdata);
 
+	if (gpio_is_valid(drvdata->gpio))
+		gpio_free(drvdata->gpio);
+
 	return 0;
 }
 

drivers/regulator/lp3971.c

@@ -541,7 +541,7 @@ static struct i2c_driver lp3971_i2c_driver = {
 
 static int __init lp3971_module_init(void)
 {
-	int ret = -ENODEV;
+	int ret;
 
 	ret = i2c_add_driver(&lp3971_i2c_driver);
 	if (ret != 0)

drivers/regulator/pcf50633-regulator.c

@@ -24,11 +24,12 @@
 #include <linux/mfd/pcf50633/core.h>
 #include <linux/mfd/pcf50633/pmic.h>
 
-#define PCF50633_REGULATOR(_name, _id) 		\
+#define PCF50633_REGULATOR(_name, _id, _n) 		\
 	{					\
 		.name = _name, 			\
 		.id = _id,			\
 		.ops = &pcf50633_regulator_ops,	\
+		.n_voltages = _n, \
 		.type = REGULATOR_VOLTAGE, 	\
 		.owner = THIS_MODULE, 		\
 	}
@@ -149,33 +150,20 @@ static int pcf50633_regulator_set_voltage(struct regulator_dev *rdev,
 	return pcf50633_reg_write(pcf, regnr, volt_bits);
 }
 
-static int pcf50633_regulator_get_voltage(struct regulator_dev *rdev)
+static int pcf50633_regulator_voltage_value(enum pcf50633_regulator_id id,
+						u8 bits)
 {
-	struct pcf50633 *pcf;
-	int regulator_id, millivolts, volt_bits;
-	u8 regnr;
-
-	pcf = rdev_get_drvdata(rdev);;
+	int millivolts;
 
-	regulator_id = rdev_get_id(rdev);
-	if (regulator_id >= PCF50633_NUM_REGULATORS)
-		return -EINVAL;
-
-	regnr = pcf50633_regulator_registers[regulator_id];
-
-	volt_bits = pcf50633_reg_read(pcf, regnr);
-	if (volt_bits < 0)
-		return -1;
-
-	switch (regulator_id) {
+	switch (id) {
 	case PCF50633_REGULATOR_AUTO:
-		millivolts = auto_voltage_value(volt_bits);
+		millivolts = auto_voltage_value(bits);
 		break;
 	case PCF50633_REGULATOR_DOWN1:
-		millivolts = down_voltage_value(volt_bits);
+		millivolts = down_voltage_value(bits);
 		break;
 	case PCF50633_REGULATOR_DOWN2:
-		millivolts = down_voltage_value(volt_bits);
+		millivolts = down_voltage_value(bits);
 		break;
 	case PCF50633_REGULATOR_LDO1:
 	case PCF50633_REGULATOR_LDO2:
@@ -184,7 +172,7 @@ static int pcf50633_regulator_get_voltage(struct regulator_dev *rdev)
 	case PCF50633_REGULATOR_LDO5:
 	case PCF50633_REGULATOR_LDO6:
 	case PCF50633_REGULATOR_HCLDO:
-		millivolts = ldo_voltage_value(volt_bits);
+		millivolts = ldo_voltage_value(bits);
 		break;
 	default:
 		return -EINVAL;
@@ -193,6 +181,49 @@ static int pcf50633_regulator_get_voltage(struct regulator_dev *rdev)
 	return millivolts * 1000;
 }
 
+static int pcf50633_regulator_get_voltage(struct regulator_dev *rdev)
+{
+	struct pcf50633 *pcf;
+	int regulator_id;
+	u8 volt_bits, regnr;
+
+	pcf = rdev_get_drvdata(rdev);
+
+	regulator_id = rdev_get_id(rdev);
+	if (regulator_id >= PCF50633_NUM_REGULATORS)
+		return -EINVAL;
+
+	regnr = pcf50633_regulator_registers[regulator_id];
+
+	volt_bits = pcf50633_reg_read(pcf, regnr);
+
+	return pcf50633_regulator_voltage_value(regulator_id, volt_bits);
+}
+
+static int pcf50633_regulator_list_voltage(struct regulator_dev *rdev,
+						unsigned int index)
+{
+	struct pcf50633 *pcf;
+	int regulator_id;
+
+	pcf = rdev_get_drvdata(rdev);
+
+	regulator_id = rdev_get_id(rdev);
+
+	switch (regulator_id) {
+	case PCF50633_REGULATOR_AUTO:
+		index += 0x2f;
+		break;
+	case PCF50633_REGULATOR_HCLDO:
+		index += 0x01;
+		break;
+	default:
+		break;
+	}
+
+	return pcf50633_regulator_voltage_value(regulator_id, index);
+}
+
 static int pcf50633_regulator_enable(struct regulator_dev *rdev)
 {
 	struct pcf50633 *pcf = rdev_get_drvdata(rdev);
@@ -246,6 +277,7 @@ static int pcf50633_regulator_is_enabled(struct regulator_dev *rdev)
 static struct regulator_ops pcf50633_regulator_ops = {
 	.set_voltage = pcf50633_regulator_set_voltage,
 	.get_voltage = pcf50633_regulator_get_voltage,
+	.list_voltage = pcf50633_regulator_list_voltage,
 	.enable = pcf50633_regulator_enable,
 	.disable = pcf50633_regulator_disable,
 	.is_enabled = pcf50633_regulator_is_enabled,
@@ -253,27 +285,27 @@ static struct regulator_ops pcf50633_regulator_ops = {
 
 static struct regulator_desc regulators[] = {
 	[PCF50633_REGULATOR_AUTO] =
-		PCF50633_REGULATOR("auto", PCF50633_REGULATOR_AUTO),
+		PCF50633_REGULATOR("auto", PCF50633_REGULATOR_AUTO, 80),
 	[PCF50633_REGULATOR_DOWN1] =
-		PCF50633_REGULATOR("down1", PCF50633_REGULATOR_DOWN1),
+		PCF50633_REGULATOR("down1", PCF50633_REGULATOR_DOWN1, 95),
 	[PCF50633_REGULATOR_DOWN2] =
-		PCF50633_REGULATOR("down2", PCF50633_REGULATOR_DOWN2),
+		PCF50633_REGULATOR("down2", PCF50633_REGULATOR_DOWN2, 95),
 	[PCF50633_REGULATOR_LDO1] =
-		PCF50633_REGULATOR("ldo1", PCF50633_REGULATOR_LDO1),
+		PCF50633_REGULATOR("ldo1", PCF50633_REGULATOR_LDO1, 27),
 	[PCF50633_REGULATOR_LDO2] =
-		PCF50633_REGULATOR("ldo2", PCF50633_REGULATOR_LDO2),
+		PCF50633_REGULATOR("ldo2", PCF50633_REGULATOR_LDO2, 27),
 	[PCF50633_REGULATOR_LDO3] =
-		PCF50633_REGULATOR("ldo3", PCF50633_REGULATOR_LDO3),
+		PCF50633_REGULATOR("ldo3", PCF50633_REGULATOR_LDO3, 27),
 	[PCF50633_REGULATOR_LDO4] =
-		PCF50633_REGULATOR("ldo4", PCF50633_REGULATOR_LDO4),
+		PCF50633_REGULATOR("ldo4", PCF50633_REGULATOR_LDO4, 27),
 	[PCF50633_REGULATOR_LDO5] =
-		PCF50633_REGULATOR("ldo5", PCF50633_REGULATOR_LDO5),
+		PCF50633_REGULATOR("ldo5", PCF50633_REGULATOR_LDO5, 27),
 	[PCF50633_REGULATOR_LDO6] =
-		PCF50633_REGULATOR("ldo6", PCF50633_REGULATOR_LDO6),
+		PCF50633_REGULATOR("ldo6", PCF50633_REGULATOR_LDO6, 27),
 	[PCF50633_REGULATOR_HCLDO] =
-		PCF50633_REGULATOR("hcldo", PCF50633_REGULATOR_HCLDO),
+		PCF50633_REGULATOR("hcldo", PCF50633_REGULATOR_HCLDO, 26),
 	[PCF50633_REGULATOR_MEMLDO] =
-		PCF50633_REGULATOR("memldo", PCF50633_REGULATOR_MEMLDO),
+		PCF50633_REGULATOR("memldo", PCF50633_REGULATOR_MEMLDO, 0),
 };
 
 static int __devinit pcf50633_regulator_probe(struct platform_device *pdev)

drivers/regulator/userspace-consumer.c

@@ -93,16 +93,21 @@ static ssize_t reg_set_state(struct device *dev, struct device_attribute *attr,
 static DEVICE_ATTR(name, 0444, reg_show_name, NULL);
 static DEVICE_ATTR(state, 0644, reg_show_state, reg_set_state);
 
-static struct device_attribute *attributes[] = {
-	&dev_attr_name,
-	&dev_attr_state,
+static struct attribute *attributes[] = {
+	&dev_attr_name.attr,
+	&dev_attr_state.attr,
+	NULL,
+};
+
+static const struct attribute_group attr_group = {
+	.attrs	= attributes,
 };
 
 static int regulator_userspace_consumer_probe(struct platform_device *pdev)
 {
 	struct regulator_userspace_consumer_data *pdata;
 	struct userspace_consumer_data *drvdata;
-	int ret, i;
+	int ret;
 
 	pdata = pdev->dev.platform_data;
 	if (!pdata)
@@ -125,31 +130,29 @@ static int regulator_userspace_consumer_probe(struct platform_device *pdev)
 		goto err_alloc_supplies;
 	}
 
-	for (i = 0; i < ARRAY_SIZE(attributes); i++) {
-		ret = device_create_file(&pdev->dev, attributes[i]);
-		if (ret != 0)
-			goto err_create_attrs;
-	}
+	ret = sysfs_create_group(&pdev->dev.kobj, &attr_group);
+	if (ret != 0)
+		goto err_create_attrs;
 
-	if (pdata->init_on)
+	if (pdata->init_on) {
 		ret = regulator_bulk_enable(drvdata->num_supplies,
 					    drvdata->supplies);
-
-	drvdata->enabled = pdata->init_on;
-
-	if (ret) {
-		dev_err(&pdev->dev, "Failed to set initial state: %d\n", ret);
-		goto err_create_attrs;
+		if (ret) {
+			dev_err(&pdev->dev,
+				"Failed to set initial state: %d\n", ret);
+			goto err_enable;
+		}
 	}
 
+	drvdata->enabled = pdata->init_on;
 	platform_set_drvdata(pdev, drvdata);
 
 	return 0;
 
-err_create_attrs:
-	for (i = 0; i < ARRAY_SIZE(attributes); i++)
-		device_remove_file(&pdev->dev, attributes[i]);
+err_enable:
+	sysfs_remove_group(&pdev->dev.kobj, &attr_group);
 
+err_create_attrs:
 	regulator_bulk_free(drvdata->num_supplies, drvdata->supplies);
 
 err_alloc_supplies:
@@ -160,10 +163,8 @@ static int regulator_userspace_consumer_probe(struct platform_device *pdev)
 static int regulator_userspace_consumer_remove(struct platform_device *pdev)
 {
 	struct userspace_consumer_data *data = platform_get_drvdata(pdev);
-	int i;
 
-	for (i = 0; i < ARRAY_SIZE(attributes); i++)
-		device_remove_file(&pdev->dev, attributes[i]);
+	sysfs_remove_group(&pdev->dev.kobj, &attr_group);
 
 	if (data->enabled)
 		regulator_bulk_disable(data->num_supplies, data->supplies);

drivers/regulator/virtual.c

@@ -27,71 +27,81 @@ struct virtual_consumer_data {
 	unsigned int mode;
 };
 
-static void update_voltage_constraints(struct virtual_consumer_data *data)
+static void update_voltage_constraints(struct device *dev,
+				       struct virtual_consumer_data *data)
 {
 	int ret;
 
 	if (data->min_uV && data->max_uV
 	    && data->min_uV <= data->max_uV) {
+		dev_dbg(dev, "Requesting %d-%duV\n",
+			data->min_uV, data->max_uV);
 		ret = regulator_set_voltage(data->regulator,
-					    data->min_uV, data->max_uV);
+					data->min_uV, data->max_uV);
 		if (ret != 0) {
-			printk(KERN_ERR "regulator_set_voltage() failed: %d\n",
-			       ret);
+			dev_err(dev,
+				"regulator_set_voltage() failed: %d\n", ret);
 			return;
 		}
 	}
 
 	if (data->min_uV && data->max_uV && !data->enabled) {
+		dev_dbg(dev, "Enabling regulator\n");
 		ret = regulator_enable(data->regulator);
 		if (ret == 0)
 			data->enabled = 1;
 		else
-			printk(KERN_ERR "regulator_enable() failed: %d\n",
+			dev_err(dev, "regulator_enable() failed: %d\n",
 				ret);
 	}
 
 	if (!(data->min_uV && data->max_uV) && data->enabled) {
+		dev_dbg(dev, "Disabling regulator\n");
 		ret = regulator_disable(data->regulator);
 		if (ret == 0)
 			data->enabled = 0;
 		else
-			printk(KERN_ERR "regulator_disable() failed: %d\n",
+			dev_err(dev, "regulator_disable() failed: %d\n",
 				ret);
 	}
 }
 
-static void update_current_limit_constraints(struct virtual_consumer_data
-						*data)
+static void update_current_limit_constraints(struct device *dev,
+					  struct virtual_consumer_data *data)
 {
 	int ret;
 
 	if (data->max_uA
 	    && data->min_uA <= data->max_uA) {
+		dev_dbg(dev, "Requesting %d-%duA\n",
+			data->min_uA, data->max_uA);
 		ret = regulator_set_current_limit(data->regulator,
 					data->min_uA, data->max_uA);
 		if (ret != 0) {
-			pr_err("regulator_set_current_limit() failed: %d\n",
-			       ret);
+			dev_err(dev,
+				"regulator_set_current_limit() failed: %d\n",
+				ret);
 			return;
 		}
 	}
 
 	if (data->max_uA && !data->enabled) {
+		dev_dbg(dev, "Enabling regulator\n");
 		ret = regulator_enable(data->regulator);
 		if (ret == 0)
 			data->enabled = 1;
 		else
-			printk(KERN_ERR "regulator_enable() failed: %d\n",
+			dev_err(dev, "regulator_enable() failed: %d\n",
 				ret);
 	}
 
 	if (!(data->min_uA && data->max_uA) && data->enabled) {
+		dev_dbg(dev, "Disabling regulator\n");
 		ret = regulator_disable(data->regulator);
 		if (ret == 0)
 			data->enabled = 0;
 		else
-			printk(KERN_ERR "regulator_disable() failed: %d\n",
+			dev_err(dev, "regulator_disable() failed: %d\n",
 				ret);
 	}
 }
@@ -115,7 +125,7 @@ static ssize_t set_min_uV(struct device *dev, struct device_attribute *attr,
 	mutex_lock(&data->lock);
 
 	data->min_uV = val;
-	update_voltage_constraints(data);
+	update_voltage_constraints(dev, data);
 
 	mutex_unlock(&data->lock);
 
@@ -141,7 +151,7 @@ static ssize_t set_max_uV(struct device *dev, struct device_attribute *attr,
 	mutex_lock(&data->lock);
 
 	data->max_uV = val;
-	update_voltage_constraints(data);
+	update_voltage_constraints(dev, data);
 
 	mutex_unlock(&data->lock);
 
@@ -167,7 +177,7 @@ static ssize_t set_min_uA(struct device *dev, struct device_attribute *attr,
 	mutex_lock(&data->lock);
 
 	data->min_uA = val;
-	update_current_limit_constraints(data);
+	update_current_limit_constraints(dev, data);
 
 	mutex_unlock(&data->lock);
 
@@ -193,7 +203,7 @@ static ssize_t set_max_uA(struct device *dev, struct device_attribute *attr,
 	mutex_lock(&data->lock);
 
 	data->max_uA = val;
-	update_current_limit_constraints(data);
+	update_current_limit_constraints(dev, data);
 
 	mutex_unlock(&data->lock);
 
@@ -276,8 +286,7 @@ static int regulator_virtual_consumer_probe(struct platform_device *pdev)
 
 	drvdata = kzalloc(sizeof(struct virtual_consumer_data), GFP_KERNEL);
 	if (drvdata == NULL) {
-		ret = -ENOMEM;
-		goto err;
+		return -ENOMEM;
 	}
 
 	mutex_init(&drvdata->lock);
@@ -285,13 +294,18 @@ static int regulator_virtual_consumer_probe(struct platform_device *pdev)
 	drvdata->regulator = regulator_get(&pdev->dev, reg_id);
 	if (IS_ERR(drvdata->regulator)) {
 		ret = PTR_ERR(drvdata->regulator);
+		dev_err(&pdev->dev, "Failed to obtain supply '%s': %d\n",
+			reg_id, ret);
 		goto err;
 	}
 
 	for (i = 0; i < ARRAY_SIZE(attributes); i++) {
 		ret = device_create_file(&pdev->dev, attributes[i]);
-		if (ret != 0)
-			goto err;
+		if (ret != 0) {
+			dev_err(&pdev->dev, "Failed to create attr %d: %d\n",
+				i, ret);
+			goto err_regulator;
+		}
 	}
 
 	drvdata->mode = regulator_get_mode(drvdata->regulator);
@@ -300,6 +314,8 @@ static int regulator_virtual_consumer_probe(struct platform_device *pdev)
 
 	return 0;
 
+err_regulator:
+	regulator_put(drvdata->regulator);
 err:
 	for (i = 0; i < ARRAY_SIZE(attributes); i++)
 		device_remove_file(&pdev->dev, attributes[i]);

drivers/regulator/wm8350-regulator.c

@@ -1419,6 +1419,8 @@ int wm8350_register_regulator(struct wm8350 *wm8350, int reg,
 {
 	struct platform_device *pdev;
 	int ret;
+	if (reg < 0 || reg >= NUM_WM8350_REGULATORS)
+		return -EINVAL;
 
 	if (wm8350->pmic.pdev[reg])
 		return -EBUSY;

include/linux/mfd/da903x.h

 #ifndef __LINUX_PMIC_DA903X_H
 #define __LINUX_PMIC_DA903X_H
 
-/* Unified sub device IDs for DA9030/DA9034 */
+/* Unified sub device IDs for DA9030/DA9034/DA9035 */
 enum {
 	DA9030_ID_LED_1,
 	DA9030_ID_LED_2,
@@ -57,6 +57,8 @@ enum {
 	DA9034_ID_LDO13,
 	DA9034_ID_LDO14,
 	DA9034_ID_LDO15,
+
+	DA9035_ID_BUCK3,
 };
 
 /*

include/linux/regulator/consumer.h

@@ -125,6 +125,8 @@ struct regulator_bulk_data {
 /* regulator get and put */
 struct regulator *__must_check regulator_get(struct device *dev,
 					     const char *id);
+struct regulator *__must_check regulator_get_exclusive(struct device *dev,
+						       const char *id);
 void regulator_put(struct regulator *regulator);
 
 /* regulator output control and status */
@@ -144,6 +146,8 @@ void regulator_bulk_free(int num_consumers,
 
 int regulator_count_voltages(struct regulator *regulator);
 int regulator_list_voltage(struct regulator *regulator, unsigned selector);
+int regulator_is_supported_voltage(struct regulator *regulator,
+				   int min_uV, int max_uV);
 int regulator_set_voltage(struct regulator *regulator, int min_uV, int max_uV);
 int regulator_get_voltage(struct regulator *regulator);
 int regulator_set_current_limit(struct regulator *regulator,

include/linux/regulator/driver.h

@@ -37,7 +37,8 @@ enum regulator_status {
  *
  * @enable: Configure the regulator as enabled.
  * @disable: Configure the regulator as disabled.
- * @is_enabled: Return 1 if the regulator is enabled, 0 otherwise.
+ * @is_enabled: Return 1 if the regulator is enabled, 0 if not.
+ *		May also return negative errno.
  *
  * @set_voltage: Set the voltage for the regulator within the range specified.
  *               The driver should select the voltage closest to min_uV.
@@ -162,6 +163,8 @@ struct regulator_desc {
 struct regulator_dev {
 	struct regulator_desc *desc;
 	int use_count;
+	int open_count;
+	int exclusive;
 
 	/* lists we belong to */
 	struct list_head list; /* list of all regulators */

include/linux/regulator/fixed.h

@@ -5,6 +5,9 @@
  *
  * Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
  *
+ * Copyright (c) 2009 Nokia Corporation
+ * Roger Quadros <ext-roger.quadros@nokia.com>
+ *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of the
@@ -16,9 +19,30 @@
 
 struct regulator_init_data;
 
+/**
+ * struct fixed_voltage_config - fixed_voltage_config structure
+ * @supply_name:	Name of the regulator supply
+ * @microvolts:		Output voltage of regulator
+ * @gpio:		GPIO to use for enable control
+ * 			set to -EINVAL if not used
+ * @enable_high:	Polarity of enable GPIO
+ *			1 = Active high, 0 = Active low
+ * @enabled_at_boot:	Whether regulator has been enabled at
+ * 			boot or not. 1 = Yes, 0 = No
+ * 			This is used to keep the regulator at
+ * 			the default state
+ * @init_data:		regulator_init_data
+ *
+ * This structure contains fixed voltage regulator configuration
+ * information that must be passed by platform code to the fixed
+ * voltage regulator driver.
+ */
 struct fixed_voltage_config {
 	const char *supply_name;
 	int microvolts;
+	int gpio;
+	unsigned enable_high:1;
+	unsigned enabled_at_boot:1;
 	struct regulator_init_data *init_data;
 };
 

include/linux/regulator/machine.h

@@ -41,7 +41,7 @@ struct regulator;
 #define REGULATOR_CHANGE_DRMS		0x10
 
 /**
- * struct regulator_state - regulator state during low power syatem states
+ * struct regulator_state - regulator state during low power system states
  *
  * This describes a regulators state during a system wide low power state.
  *
@@ -117,25 +117,37 @@ struct regulation_constraints {
 	/* mode to set on startup */
 	unsigned int initial_mode;
 
-	/* constriant flags */
+	/* constraint flags */
 	unsigned always_on:1;	/* regulator never off when system is on */
 	unsigned boot_on:1;	/* bootloader/firmware enabled regulator */
-	unsigned apply_uV:1;	/* apply uV constraint iff min == max */
+	unsigned apply_uV:1;	/* apply uV constraint if min == max */
 };
 
 /**
  * struct regulator_consumer_supply - supply -> device mapping
  *
- * This maps a supply name to a device.
+ * This maps a supply name to a device.  Only one of dev or dev_name
+ * can be specified.  Use of dev_name allows support for buses which
+ * make struct device available late such as I2C and is the preferred
+ * form.
  *
  * @dev: Device structure for the consumer.
+ * @dev_name: Result of dev_name() for the consumer.
  * @supply: Name for the supply.
  */
 struct regulator_consumer_supply {
 	struct device *dev;	/* consumer */
+	const char *dev_name;   /* dev_name() for consumer */
 	const char *supply;	/* consumer supply - e.g. "vcc" */
 };
 
+/* Initialize struct regulator_consumer_supply */
+#define REGULATOR_SUPPLY(_name, _dev_name)			\
+{								\
+	.supply		= _name,				\
+	.dev_name	= _dev_name,				\
+}
+
 /**
  * struct regulator_init_data - regulator platform initialisation data.
  *
@@ -166,6 +178,12 @@ struct regulator_init_data {
 
 int regulator_suspend_prepare(suspend_state_t state);
 
+#ifdef CONFIG_REGULATOR
 void regulator_has_full_constraints(void);
+#else
+static inline void regulator_has_full_constraints(void)
+{
+}
+#endif
 
 #endif

include/linux/regulator/max1586.h

@@ -36,7 +36,7 @@
  * max1586_subdev_data - regulator data
  * @id: regulator Id (either MAX1586_V3 or MAX1586_V6)
  * @name: regulator cute name (example for V3: "vcc_core")
- * @platform_data: regulator init data (contraints, supplies, ...)
+ * @platform_data: regulator init data (constraints, supplies, ...)
  */
 struct max1586_subdev_data {
 	int				id;
@@ -46,7 +46,7 @@ struct max1586_subdev_data {
 
 /**
  * max1586_platform_data - platform data for max1586
- * @num_subdevs: number of regultors used (may be 1 or 2)
+ * @num_subdevs: number of regulators used (may be 1 or 2)
  * @subdevs: regulator used
  *           At most, there will be a regulator for V3 and one for V6 voltages.
  * @v3_gain: gain on the V3 voltage output multiplied by 1e6.