tty: 8250: Add 64byte UART support for FSL platforms

Some of FSL SoCs like T1040 has new version of UART controller which
can support 64byte FiFo.
To enable 64 byte support, following needs to be done:
-FCR[EN64] needs to be programmed to 1 to enable it.
-Also, when FCR[EN64]==1, RTL bits to be used as below
to define various Receive Trigger Levels:
        -FCR[RTL] = 00  1 byte
        -FCR[RTL] = 01  16 bytes
        -FCR[RTL] = 10  32 bytes
        -FCR[RTL] = 11  56 bytes
-tx_loadsz is set to 63-bytes instead of 64-bytes to implement
 workaround of errata A-008006 which states that tx_loadsz should
 be configured less than Maximum supported fifo bytes
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/8250/8250_core.c

@@ -329,6 +329,17 @@ static const struct serial8250_config uart_config[] = {
 		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
 		.flags		= UART_CAP_FIFO | UART_CAP_AFE,
 	},
+/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
+workaround of errata A-008006 which states that tx_loadsz should  be
+configured less than Maximum supported fifo bytes */
+	[PORT_16550A_FSL64] = {
+		.name		= "16550A_FSL64",
+		.fifo_size	= 64,
+		.tx_loadsz	= 63,
+		.fcr		= UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+				  UART_FCR7_64BYTE,
+		.flags		= UART_CAP_FIFO,
+	},
 };
 
 /* Uart divisor latch read */
@@ -956,7 +967,17 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 			up->port.type = PORT_16650;
 			up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
 		} else {
-			DEBUG_AUTOCONF("Motorola 8xxx DUART ");
+			serial_out(up, UART_LCR, 0);
+			serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+				   UART_FCR7_64BYTE);
+			status1 = serial_in(up, UART_IIR) >> 5;
+			serial_out(up, UART_FCR, 0);
+			serial_out(up, UART_LCR, 0);
+
+			if (status1 == 7)
+				up->port.type = PORT_16550A_FSL64;
+			else
+				DEBUG_AUTOCONF("Motorola 8xxx DUART ");
 		}
 		serial_out(up, UART_EFR, 0);
 		return;

include/uapi/linux/serial_core.h

@@ -55,7 +55,8 @@
 #define PORT_ALTR_16550_F64 27	/* Altera 16550 UART with 64 FIFOs */
 #define PORT_ALTR_16550_F128 28 /* Altera 16550 UART with 128 FIFOs */
 #define PORT_RT2880	29	/* Ralink RT2880 internal UART */
-#define PORT_MAX_8250	29	/* max port ID */
+#define PORT_16550A_FSL64 30	/* Freescale 16550 UART with 64 FIFOs */
+#define PORT_MAX_8250	30	/* max port ID */
 
 /*
  * ARM specific type numbers.  These are not currently guaranteed

include/uapi/linux/serial_reg.h

@@ -86,7 +86,8 @@
 #define UART_FCR6_T_TRIGGER_8	0x10 /* Mask for transmit trigger set at 8 */
 #define UART_FCR6_T_TRIGGER_24  0x20 /* Mask for transmit trigger set at 24 */
 #define UART_FCR6_T_TRIGGER_30	0x30 /* Mask for transmit trigger set at 30 */
-#define UART_FCR7_64BYTE	0x20 /* Go into 64 byte mode (TI16C750) */
+#define UART_FCR7_64BYTE	0x20 /* Go into 64 byte mode (TI16C750 and
+					some Freescale UARTs) */
 
 #define UART_FCR_R_TRIG_SHIFT		6
 #define UART_FCR_R_TRIG_BITS(x)		\