ide: add proper PCI PM support (v2)

* Keep pointer to ->init_chipset method also in
  struct ide_host and set it in ide_host_alloc_all().

* Add ide_pci_suspend() and ide_pci_resume() helpers
  (default ->suspend and ->resume implementations).

* ->init_chipset can no longer be marked __devinit.

* Add proper PCI PM support to IDE PCI host drivers
  (rz1000.c and tc86c001.c are skipped for now since
  they need to be converted from using ->init_hwif
  to use ->init_chipset instead).

v2:
* Cleanup CONFIG_PM #ifdef-s per akpm's suggestion.

Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 1785192b
......@@ -1586,8 +1586,10 @@ struct ide_host *ide_host_alloc_all(const struct ide_port_info *d,
if (hws[0])
host->dev[0] = hws[0]->dev;
if (d)
if (d) {
host->init_chipset = d->init_chipset;
host->host_flags = d->host_flags;
}
return host;
}
......
......@@ -139,7 +139,7 @@ static void aec_set_pio_mode(ide_drive_t *drive, const u8 pio)
drive->hwif->port_ops->set_dma_mode(drive, pio + XFER_PIO_0);
}
static unsigned int __devinit init_chipset_aec62xx(struct pci_dev *dev)
static unsigned int init_chipset_aec62xx(struct pci_dev *dev)
{
/* These are necessary to get AEC6280 Macintosh cards to work */
if ((dev->device == PCI_DEVICE_ID_ARTOP_ATP865) ||
......@@ -307,6 +307,8 @@ static struct pci_driver driver = {
.id_table = aec62xx_pci_tbl,
.probe = aec62xx_init_one,
.remove = __devexit_p(aec62xx_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init aec62xx_ide_init(void)
......
......@@ -213,7 +213,7 @@ static int ali15x3_dma_setup(ide_drive_t *drive)
* appropriate also sets up the 1533 southbridge.
*/
static unsigned int __devinit init_chipset_ali15x3(struct pci_dev *dev)
static unsigned int init_chipset_ali15x3(struct pci_dev *dev)
{
unsigned long flags;
u8 tmpbyte;
......@@ -581,6 +581,8 @@ static struct pci_driver driver = {
.id_table = alim15x3_pci_tbl,
.probe = alim15x3_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init ali15x3_ide_init(void)
......
......@@ -112,13 +112,13 @@ static void amd_set_pio_mode(ide_drive_t *drive, const u8 pio)
amd_set_drive(drive, XFER_PIO_0 + pio);
}
static void __devinit amd7409_cable_detect(struct pci_dev *dev)
static void amd7409_cable_detect(struct pci_dev *dev)
{
/* no host side cable detection */
amd_80w = 0x03;
}
static void __devinit amd7411_cable_detect(struct pci_dev *dev)
static void amd7411_cable_detect(struct pci_dev *dev)
{
int i;
u32 u = 0;
......@@ -140,7 +140,7 @@ static void __devinit amd7411_cable_detect(struct pci_dev *dev)
* The initialization callback. Initialize drive independent registers.
*/
static unsigned int __devinit init_chipset_amd74xx(struct pci_dev *dev)
static unsigned int init_chipset_amd74xx(struct pci_dev *dev)
{
u8 t = 0, offset = amd_offset(dev);
......@@ -324,6 +324,8 @@ static struct pci_driver driver = {
.id_table = amd74xx_pci_tbl,
.probe = amd74xx_probe,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init amd74xx_ide_init(void)
......
......@@ -187,6 +187,8 @@ static struct pci_driver driver = {
.id_table = atiixp_pci_tbl,
.probe = atiixp_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init atiixp_ide_init(void)
......
......@@ -331,7 +331,7 @@ static int cmd646_1_dma_end(ide_drive_t *drive)
return (dma_stat & 7) != 4;
}
static unsigned int __devinit init_chipset_cmd64x(struct pci_dev *dev)
static unsigned int init_chipset_cmd64x(struct pci_dev *dev)
{
u8 mrdmode = 0;
......@@ -510,6 +510,8 @@ static struct pci_driver driver = {
.id_table = cmd64x_pci_tbl,
.probe = cmd64x_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cmd64x_ide_init(void)
......
......@@ -149,6 +149,8 @@ static struct pci_driver driver = {
.name = "Cyrix_IDE",
.id_table = cs5520_pci_tbl,
.probe = cs5520_init_one,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cs5520_ide_init(void)
......
......@@ -134,7 +134,7 @@ static void cs5530_set_dma_mode(ide_drive_t *drive, const u8 mode)
* Initialize the cs5530 bridge for reliable IDE DMA operation.
*/
static unsigned int __devinit init_chipset_cs5530(struct pci_dev *dev)
static unsigned int init_chipset_cs5530(struct pci_dev *dev)
{
struct pci_dev *master_0 = NULL, *cs5530_0 = NULL;
......@@ -272,6 +272,8 @@ static struct pci_driver driver = {
.id_table = cs5530_pci_tbl,
.probe = cs5530_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cs5530_ide_init(void)
......
......@@ -193,10 +193,12 @@ static const struct pci_device_id cs5535_pci_tbl[] = {
MODULE_DEVICE_TABLE(pci, cs5535_pci_tbl);
static struct pci_driver driver = {
.name = "CS5535_IDE",
.id_table = cs5535_pci_tbl,
.probe = cs5535_init_one,
.remove = ide_pci_remove,
.name = "CS5535_IDE",
.id_table = cs5535_pci_tbl,
.probe = cs5535_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cs5535_ide_init(void)
......
......@@ -332,7 +332,7 @@ static void cy82c693_set_pio_mode(ide_drive_t *drive, const u8 pio)
/*
* this function is called during init and is used to setup the cy82c693 chip
*/
static unsigned int __devinit init_chipset_cy82c693(struct pci_dev *dev)
static unsigned int init_chipset_cy82c693(struct pci_dev *dev)
{
if (PCI_FUNC(dev->devfn) != 1)
return 0;
......@@ -448,6 +448,8 @@ static struct pci_driver driver = {
.id_table = cy82c693_pci_tbl,
.probe = cy82c693_init_one,
.remove = __devexit_p(cy82c693_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init cy82c693_ide_init(void)
......
......@@ -171,6 +171,8 @@ static struct pci_driver driver = {
.id_table = generic_pci_tbl,
.probe = generic_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init generic_ide_init(void)
......
......@@ -78,7 +78,7 @@ static void hpt34x_set_pio_mode(ide_drive_t *drive, const u8 pio)
*/
#define HPT34X_PCI_INIT_REG 0x80
static unsigned int __devinit init_chipset_hpt34x(struct pci_dev *dev)
static unsigned int init_chipset_hpt34x(struct pci_dev *dev)
{
int i = 0;
unsigned long hpt34xIoBase = pci_resource_start(dev, 4);
......@@ -171,6 +171,8 @@ static struct pci_driver driver = {
.id_table = hpt34x_pci_tbl,
.probe = hpt34x_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init hpt34x_ide_init(void)
......
......@@ -943,7 +943,7 @@ static void hpt3xxn_rw_disk(ide_drive_t *drive, struct request *rq)
* Perform a calibration cycle on the DPLL.
* Returns 1 if this succeeds
*/
static int __devinit hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f_high)
static int hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f_high)
{
u32 dpll = (f_high << 16) | f_low | 0x100;
u8 scr2;
......@@ -971,7 +971,7 @@ static int __devinit hpt37x_calibrate_dpll(struct pci_dev *dev, u16 f_low, u16 f
return 1;
}
static void __devinit hpt3xx_disable_fast_irq(struct pci_dev *dev, u8 mcr_addr)
static void hpt3xx_disable_fast_irq(struct pci_dev *dev, u8 mcr_addr)
{
struct ide_host *host = pci_get_drvdata(dev);
struct hpt_info *info = host->host_priv + (&dev->dev == host->dev[1]);
......@@ -1001,7 +1001,7 @@ static void __devinit hpt3xx_disable_fast_irq(struct pci_dev *dev, u8 mcr_addr)
pci_write_config_byte(dev, mcr_addr + 1, new_mcr);
}
static unsigned int __devinit init_chipset_hpt366(struct pci_dev *dev)
static unsigned int init_chipset_hpt366(struct pci_dev *dev)
{
unsigned long io_base = pci_resource_start(dev, 4);
struct hpt_info *info = hpt3xx_get_info(&dev->dev);
......@@ -1627,6 +1627,8 @@ static struct pci_driver driver = {
.id_table = hpt366_pci_tbl,
.probe = hpt366_init_one,
.remove = __devexit_p(hpt366_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init hpt366_ide_init(void)
......
......@@ -194,6 +194,8 @@ static struct pci_driver driver = {
.id_table = it8213_pci_tbl,
.probe = it8213_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init it8213_ide_init(void)
......
......@@ -586,7 +586,7 @@ static void __devinit init_hwif_it821x(ide_hwif_t *hwif)
hwif->mwdma_mask = ATA_MWDMA2;
}
static void __devinit it8212_disable_raid(struct pci_dev *dev)
static void it8212_disable_raid(struct pci_dev *dev)
{
/* Reset local CPU, and set BIOS not ready */
pci_write_config_byte(dev, 0x5E, 0x01);
......@@ -603,7 +603,7 @@ static void __devinit it8212_disable_raid(struct pci_dev *dev)
pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
}
static unsigned int __devinit init_chipset_it821x(struct pci_dev *dev)
static unsigned int init_chipset_it821x(struct pci_dev *dev)
{
u8 conf;
static char *mode[2] = { "pass through", "smart" };
......@@ -685,6 +685,8 @@ static struct pci_driver driver = {
.id_table = it821x_pci_tbl,
.probe = it821x_init_one,
.remove = __devexit_p(it821x_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init it821x_ide_init(void)
......
......@@ -154,6 +154,8 @@ static struct pci_driver driver = {
.id_table = jmicron_pci_tbl,
.probe = jmicron_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init jmicron_ide_init(void)
......
......@@ -339,6 +339,8 @@ static struct pci_driver driver = {
.id_table = ns87415_pci_tbl,
.probe = ns87415_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init ns87415_ide_init(void)
......
......@@ -225,6 +225,8 @@ static struct pci_driver driver = {
.id_table = opti621_pci_tbl,
.probe = opti621_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init opti621_ide_init(void)
......
......@@ -226,7 +226,7 @@ static void pdcnew_reset(ide_drive_t *drive)
* read_counter - Read the byte count registers
* @dma_base: for the port address
*/
static long __devinit read_counter(u32 dma_base)
static long read_counter(u32 dma_base)
{
u32 pri_dma_base = dma_base, sec_dma_base = dma_base + 0x08;
u8 cnt0, cnt1, cnt2, cnt3;
......@@ -266,7 +266,7 @@ static long __devinit read_counter(u32 dma_base)
* @dma_base: for the port address
* E.g. 16949000 on 33 MHz PCI bus, i.e. half of the PCI clock.
*/
static long __devinit detect_pll_input_clock(unsigned long dma_base)
static long detect_pll_input_clock(unsigned long dma_base)
{
struct timeval start_time, end_time;
long start_count, end_count;
......@@ -309,7 +309,7 @@ static long __devinit detect_pll_input_clock(unsigned long dma_base)
}
#ifdef CONFIG_PPC_PMAC
static void __devinit apple_kiwi_init(struct pci_dev *pdev)
static void apple_kiwi_init(struct pci_dev *pdev)
{
struct device_node *np = pci_device_to_OF_node(pdev);
u8 conf;
......@@ -325,7 +325,7 @@ static void __devinit apple_kiwi_init(struct pci_dev *pdev)
}
#endif /* CONFIG_PPC_PMAC */
static unsigned int __devinit init_chipset_pdcnew(struct pci_dev *dev)
static unsigned int init_chipset_pdcnew(struct pci_dev *dev)
{
const char *name = DRV_NAME;
unsigned long dma_base = pci_resource_start(dev, 4);
......@@ -566,6 +566,8 @@ static struct pci_driver driver = {
.id_table = pdc202new_pci_tbl,
.probe = pdc202new_init_one,
.remove = __devexit_p(pdc202new_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init pdc202new_ide_init(void)
......
......@@ -264,7 +264,7 @@ static void pdc202xx_dma_timeout(ide_drive_t *drive)
ide_dma_timeout(drive);
}
static unsigned int __devinit init_chipset_pdc202xx(struct pci_dev *dev)
static unsigned int init_chipset_pdc202xx(struct pci_dev *dev)
{
unsigned long dmabase = pci_resource_start(dev, 4);
u8 udma_speed_flag = 0, primary_mode = 0, secondary_mode = 0;
......@@ -431,6 +431,8 @@ static struct pci_driver driver = {
.id_table = pdc202xx_pci_tbl,
.probe = pdc202xx_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init pdc202xx_ide_init(void)
......
......@@ -204,7 +204,7 @@ static void piix_set_dma_mode(ide_drive_t *drive, const u8 speed)
* out to be nice and simple.
*/
static unsigned int __devinit init_chipset_ich(struct pci_dev *dev)
static unsigned int init_chipset_ich(struct pci_dev *dev)
{
u32 extra = 0;
......@@ -449,6 +449,8 @@ static struct pci_driver driver = {
.id_table = piix_pci_tbl,
.probe = piix_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init piix_ide_init(void)
......
......@@ -175,7 +175,7 @@ static void svwks_set_dma_mode(ide_drive_t *drive, const u8 speed)
pci_write_config_byte(dev, 0x54, ultra_enable);
}
static unsigned int __devinit init_chipset_svwks(struct pci_dev *dev)
static unsigned int init_chipset_svwks(struct pci_dev *dev)
{
unsigned int reg;
u8 btr;
......@@ -448,6 +448,8 @@ static struct pci_driver driver = {
.id_table = svwks_pci_tbl,
.probe = svwks_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init svwks_ide_init(void)
......
......@@ -463,7 +463,7 @@ static void sil_sata_pre_reset(ide_drive_t *drive)
* to 133 MHz clocking if the system isn't already set up to do it.
*/
static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev)
static unsigned int init_chipset_siimage(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
void __iomem *ioaddr = host->host_priv;
......@@ -834,6 +834,8 @@ static struct pci_driver driver = {
.id_table = siimage_pci_tbl,
.probe = siimage_init_one,
.remove = __devexit_p(siimage_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init siimage_ide_init(void)
......
......@@ -447,7 +447,7 @@ static int __devinit sis_find_family(struct pci_dev *dev)
return chipset_family;
}
static unsigned int __devinit init_chipset_sis5513(struct pci_dev *dev)
static unsigned int init_chipset_sis5513(struct pci_dev *dev)
{
/* Make general config ops here
1/ tell IDE channels to operate in Compatibility mode only
......@@ -610,6 +610,8 @@ static struct pci_driver driver = {
.id_table = sis5513_pci_tbl,
.probe = sis5513_init_one,
.remove = __devexit_p(sis5513_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init sis5513_ide_init(void)
......
......@@ -271,7 +271,7 @@ static u8 sl82c105_bridge_revision(struct pci_dev *dev)
* channel 0 here at least, but channel 1 has to be enabled by
* firmware or arch code. We still set both to 16 bits mode.
*/
static unsigned int __devinit init_chipset_sl82c105(struct pci_dev *dev)
static unsigned int init_chipset_sl82c105(struct pci_dev *dev)
{
u32 val;
......@@ -350,6 +350,8 @@ static struct pci_driver driver = {
.id_table = sl82c105_pci_tbl,
.probe = sl82c105_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init sl82c105_ide_init(void)
......
......@@ -159,6 +159,8 @@ static struct pci_driver driver = {
.id_table = slc90e66_pci_tbl,
.probe = slc90e66_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init slc90e66_ide_init(void)
......
......@@ -119,6 +119,8 @@ static struct pci_driver driver = {
.id_table = triflex_pci_tbl,
.probe = triflex_init_one,
.remove = ide_pci_remove,
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init triflex_ide_init(void)
......
......@@ -215,7 +215,7 @@ static struct via_isa_bridge *via_config_find(struct pci_dev **isa)
/*
* Check and handle 80-wire cable presence
*/
static void __devinit via_cable_detect(struct via82cxxx_dev *vdev, u32 u)
static void via_cable_detect(struct via82cxxx_dev *vdev, u32 u)
{
int i;
......@@ -267,7 +267,7 @@ static void __devinit via_cable_detect(struct via82cxxx_dev *vdev, u32 u)
* and initialize its drive independent registers.
*/
static unsigned int __devinit init_chipset_via82cxxx(struct pci_dev *dev)
static unsigned int init_chipset_via82cxxx(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
struct via82cxxx_dev *vdev = host->host_priv;
......@@ -492,6 +492,8 @@ static struct pci_driver driver = {
.id_table = via_pci_tbl,
.probe = via_init_one,
.remove = __devexit_p(via_remove),
.suspend = ide_pci_suspend,
.resume = ide_pci_resume,
};
static int __init via_ide_init(void)
......
......@@ -659,3 +659,36 @@ void ide_pci_remove(struct pci_dev *dev)
pci_disable_device(dev);
}
EXPORT_SYMBOL_GPL(ide_pci_remove);
#ifdef CONFIG_PM
int ide_pci_suspend(struct pci_dev *dev, pm_message_t state)
{
pci_save_state(dev);
pci_disable_device(dev);
pci_set_power_state(dev, pci_choose_state(dev, state));
return 0;
}
EXPORT_SYMBOL_GPL(ide_pci_suspend);
int ide_pci_resume(struct pci_dev *dev)
{
struct ide_host *host = pci_get_drvdata(dev);
int rc;
pci_set_power_state(dev, PCI_D0);
rc = pci_enable_device(dev);
if (rc)
return rc;
pci_restore_state(dev);
pci_set_master(dev);
if (host->init_chipset)
host->init_chipset(dev);
return 0;
}
EXPORT_SYMBOL_GPL(ide_pci_resume);
#endif
......@@ -17,6 +17,7 @@
#include <linux/device.h>
#include <linux/pci.h>
#include <linux/completion.h>
#include <linux/pm.h>
#ifdef CONFIG_BLK_DEV_IDEACPI
#include <acpi/acpi.h>
#endif
......@@ -639,6 +640,7 @@ struct ide_host {
ide_hwif_t *ports[MAX_HWIFS];
unsigned int n_ports;
struct device *dev[2];
unsigned int (*init_chipset)(struct pci_dev *);
unsigned long host_flags;
void *host_priv;
};
......@@ -1264,6 +1266,14 @@ int ide_pci_init_two(struct pci_dev *, struct pci_dev *,
const struct ide_port_info *, void *);
void ide_pci_remove(struct pci_dev *);
#ifdef CONFIG_PM
int ide_pci_suspend(struct pci_dev *, pm_message_t);
int ide_pci_resume(struct pci_dev *);
#else
#define ide_pci_suspend NULL
#define ide_pci_resume NULL
#endif
void ide_map_sg(ide_drive_t *, struct request *);
void ide_init_sg_cmd(ide_drive_t *, struct request *);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment