Merge branch 'next/dt-samsung' of...

Merge branch 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt

From Kukjin Kim <kgene.kim@samsung.com>:

It is for supporting spi dt for exynos4210 and exynos5250, and got the
ack from Grant Likely for spi driver.

Note: Since this is including spi driver changes, so it was made based
on next/devel-dma-ops which touches same file, Samsung spi driver for
avoiding bad conflicts.

* 'next/dt-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
  ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS5 platforms
  ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOS5
  ARM: EXYNOS: Add spi clock support for EXYNOS5
  ARM: dts: Add nodes for spi controllers for SAMSUNG EXYNOS4 platforms
  ARM: EXYNOS: Enable platform support for SPI controllers for EXYNOX4
  ARM: EXYNOS: Fix the incorrect hierarchy of spi controller bus clock
  ARM: EXYNOS: Add device tree node for EXYNOS4 interrupt combiner controller
  spi: s3c64xx: add device tree support
  spi: s3c64xx: Remove the 'set_level' callback from controller data
  ARM: SAMSUNG: Modify s3c64xx_spi{0|1|2}_set_platdata function
  ARM: SAMSUNG: Remove pdev pointer parameter from spi gpio setup functions
  spi: s3c64xx: move controller information into driver data
  spi: s3c64xx: remove unused S3C64XX_SPI_ST_TRLCNTZ macro
  ARM: S3C64XX: Add a new dma request id for device tree based dma channel lookup
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/spi/spi-samsung.txt

+* Samsung SPI Controller
+
+The Samsung SPI controller is used to interface with various devices such as flash
+and display controllers using the SPI communication interface.
+
+Required SoC Specific Properties:
+
+- compatible: should be one of the following.
+    - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms
+    - samsung,s3c6410-spi: for s3c6410 platforms
+    - samsung,s5p6440-spi: for s5p6440 and s5p6450 platforms
+    - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms
+    - samsung,exynos4210-spi: for exynos4 and exynos5 platforms
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+
+- interrupts: The interrupt number to the cpu. The interrupt specifier format
+  depends on the interrupt controller.
+
+- tx-dma-channel: The dma channel specifier for tx operations. The format of
+  the dma specifier depends on the dma controller.
+
+- rx-dma-channel: The dma channel specifier for rx operations. The format of
+  the dma specifier depends on the dma controller.
+
+Required Board Specific Properties:
+
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+- gpios: The gpio specifier for clock, mosi and miso interface lines (in the
+  order specified). The format of the gpio specifier depends on the gpio
+  controller.
+
+Optional Board Specific Properties:
+
+- samsung,spi-src-clk: If the spi controller includes a internal clock mux to
+  select the clock source for the spi bus clock, this property can be used to
+  indicate the clock to be used for driving the spi bus clock. If not specified,
+  the clock number 0 is used as default.
+
+- num-cs: Specifies the number of chip select lines supported. If
+  not specified, the default number of chip select lines is set to 1.
+
+SPI Controller specific data in SPI slave nodes:
+
+- The spi slave nodes should provide the following information which is required
+  by the spi controller.
+
+  - cs-gpio: A gpio specifier that specifies the gpio line used as
+    the slave select line by the spi controller. The format of the gpio
+    specifier depends on the gpio controller.
+
+  - samsung,spi-feedback-delay: The sampling phase shift to be applied on the
+    miso line (to account for any lag in the miso line). The following are the
+    valid values.
+
+      - 0: No phase shift.
+      - 1: 90 degree phase shift sampling.
+      - 2: 180 degree phase shift sampling.
+      - 3: 270 degree phase shift sampling.
+
+Aliases:
+
+- All the SPI controller nodes should be represented in the aliases node using
+  the following format 'spi{n}' where n is a unique number for the alias.
+
+
+Example:
+
+- SoC Specific Portion:
+
+	spi_0: spi@12d20000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d20000 0x100>;
+		interrupts = <0 66 0>;
+		tx-dma-channel = <&pdma0 5>;
+		rx-dma-channel = <&pdma0 4>;
+	};
+
+- Board Specific Portion:
+
+	spi_0: spi@12d20000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpa2 4 2 3 0>,
+			<&gpa2 6 2 3 0>,
+			<&gpa2 7 2 3 0>;
+
+		w25q80bw@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <10000>;
+
+			controller-data {
+				cs-gpio = <&gpa2 5 1 0 3>;
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};

arch/arm/boot/dts/exynos4210-origen.dts

@@ -134,4 +134,16 @@ i2c@138C0000 {
 	i2c@138D0000 {
 		status = "disabled";
 	};
+
+	spi_0: spi@13920000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@13930000 {
+		status = "disabled";
+	};
+
+	spi_2: spi@13940000 {
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -179,4 +179,42 @@ i2c@138C0000 {
 	i2c@138D0000 {
 		status = "disabled";
 	};
+
+	spi_0: spi@13920000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@13930000 {
+		status = "disabled";
+	};
+
+	spi_2: spi@13940000 {
+		gpios = <&gpc1 1 5 3 0>,
+			<&gpc1 3 5 3 0>,
+			<&gpc1 4 5 3 0>;
+
+		w25x80@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <1000000>;
+
+			controller-data {
+				cs-gpio = <&gpc1 2 1 0 3>;
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};
 };

arch/arm/boot/dts/exynos4210.dtsi

@@ -25,6 +25,12 @@ / {
 	compatible = "samsung,exynos4210";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		spi2 = &spi_2;
+	};
+
 	gic:interrupt-controller@10490000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
@@ -33,6 +39,17 @@ gic:interrupt-controller@10490000 {
 		reg = <0x10490000 0x1000>, <0x10480000 0x100>;
 	};
 
+	combiner:interrupt-controller@10440000 {
+		compatible = "samsung,exynos4210-combiner";
+		#interrupt-cells = <2>;
+		interrupt-controller;
+		reg = <0x10440000 0x1000>;
+		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
+			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
+			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
+			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
+	};
+
 	watchdog@10060000 {
 		compatible = "samsung,s3c2410-wdt";
 		reg = <0x10060000 0x100>;
@@ -147,6 +164,36 @@ i2c@138D0000 {
 		interrupts = <0 65 0>;
 	};
 
+	spi_0: spi@13920000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x13920000 0x100>;
+		interrupts = <0 66 0>;
+		tx-dma-channel = <&pdma0 7>;
+		rx-dma-channel = <&pdma0 6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_1: spi@13930000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x13930000 0x100>;
+		interrupts = <0 67 0>;
+		tx-dma-channel = <&pdma1 7>;
+		rx-dma-channel = <&pdma1 6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_2: spi@13940000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x13940000 0x100>;
+		interrupts = <0 68 0>;
+		tx-dma-channel = <&pdma0 9>;
+		rx-dma-channel = <&pdma0 8>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -71,4 +71,42 @@ i2c@12CC0000 {
 	i2c@12CD0000 {
 		status = "disabled";
 	};
+
+	spi_0: spi@12d20000 {
+		status = "disabled";
+	};
+
+	spi_1: spi@12d30000 {
+		gpios = <&gpa2 4 2 3 0>,
+			<&gpa2 6 2 3 0>,
+			<&gpa2 7 2 3 0>;
+
+		w25q80bw@0 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "w25x80";
+			reg = <0>;
+			spi-max-frequency = <1000000>;
+
+			controller-data {
+				cs-gpio = <&gpa2 5 1 0 3>;
+				samsung,spi-feedback-delay = <0>;
+			};
+
+			partition@0 {
+				label = "U-Boot";
+				reg = <0x0 0x40000>;
+				read-only;
+			};
+
+			partition@40000 {
+				label = "Kernel";
+				reg = <0x40000 0xc0000>;
+			};
+		};
+	};
+
+	spi_2: spi@12d40000 {
+		status = "disabled";
+	};
 };

arch/arm/boot/dts/exynos5250.dtsi

@@ -23,6 +23,12 @@ / {
 	compatible = "samsung,exynos5250";
 	interrupt-parent = <&gic>;
 
+	aliases {
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		spi2 = &spi_2;
+	};
+
 	gic:interrupt-controller@10481000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
@@ -146,6 +152,36 @@ i2c@12CD0000 {
 		#size-cells = <0>;
 	};
 
+	spi_0: spi@12d20000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d20000 0x100>;
+		interrupts = <0 66 0>;
+		tx-dma-channel = <&pdma0 5>;
+		rx-dma-channel = <&pdma0 4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_1: spi@12d30000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d30000 0x100>;
+		interrupts = <0 67 0>;
+		tx-dma-channel = <&pdma1 5>;
+		rx-dma-channel = <&pdma1 4>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	spi_2: spi@12d40000 {
+		compatible = "samsung,exynos4210-spi";
+		reg = <0x12d40000 0x100>;
+		interrupts = <0 68 0>;
+		tx-dma-channel = <&pdma0 7>;
+		rx-dma-channel = <&pdma0 6>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
 	amba {
 		#address-cells = <1>;
 		#size-cells = <1>;

arch/arm/mach-exynos/clock-exynos4.c

@@ -586,17 +586,17 @@ static struct clk exynos4_init_clocks_off[] = {
 		.ctrlbit	= (1 << 13),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "exynos4210-spi.0",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 16),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "exynos4210-spi.1",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "exynos4210-spi.2",
 		.enable		= exynos4_clk_ip_peril_ctrl,
 		.ctrlbit	= (1 << 18),
 	}, {
@@ -1242,40 +1242,67 @@ static struct clksrc_clk exynos4_clk_sclk_mmc3 = {
 	.reg_div = { .reg = EXYNOS4_CLKDIV_FSYS2, .shift = 24, .size = 8 },
 };
 
+static struct clksrc_clk exynos4_clk_mdout_spi0 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.0",
+	},
+	.sources = &exynos4_clkset_group,
+	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 16, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk exynos4_clk_mdout_spi1 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.1",
+	},
+	.sources = &exynos4_clkset_group,
+	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 20, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk exynos4_clk_mdout_spi2 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.2",
+	},
+	.sources = &exynos4_clkset_group,
+	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 24, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL2, .shift = 0, .size = 4 },
+};
+
 static struct clksrc_clk exynos4_clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "exynos4210-spi.0",
+		.parent		= &exynos4_clk_mdout_spi0.clk,
 		.enable		= exynos4_clksrc_mask_peril1_ctrl,
 		.ctrlbit	= (1 << 16),
 	},
-	.sources = &exynos4_clkset_group,
-	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 16, .size = 4 },
-	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 0, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 8, .size = 8 },
 };
 
 static struct clksrc_clk exynos4_clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "exynos4210-spi.1",
+		.parent		= &exynos4_clk_mdout_spi1.clk,
 		.enable		= exynos4_clksrc_mask_peril1_ctrl,
 		.ctrlbit	= (1 << 20),
 	},
-	.sources = &exynos4_clkset_group,
-	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 20, .size = 4 },
-	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 16, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL1, .shift = 24, .size = 8 },
 };
 
 static struct clksrc_clk exynos4_clk_sclk_spi2 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "exynos4210-spi.2",
+		.parent		= &exynos4_clk_mdout_spi2.clk,
 		.enable		= exynos4_clksrc_mask_peril1_ctrl,
 		.ctrlbit	= (1 << 24),
 	},
-	.sources = &exynos4_clkset_group,
-	.reg_src = { .reg = EXYNOS4_CLKSRC_PERIL1, .shift = 24, .size = 4 },
-	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL2, .shift = 0, .size = 4 },
+	.reg_div = { .reg = EXYNOS4_CLKDIV_PERIL2, .shift = 8, .size = 8 },
 };
 
 /* Clock initialization code */
@@ -1331,7 +1358,9 @@ static struct clksrc_clk *exynos4_clksrc_cdev[] = {
 	&exynos4_clk_sclk_spi0,
 	&exynos4_clk_sclk_spi1,
 	&exynos4_clk_sclk_spi2,
-
+	&exynos4_clk_mdout_spi0,
+	&exynos4_clk_mdout_spi1,
+	&exynos4_clk_mdout_spi2,
 };
 
 static struct clk_lookup exynos4_clk_lookup[] = {
@@ -1347,9 +1376,9 @@ static struct clk_lookup exynos4_clk_lookup[] = {
 	CLKDEV_INIT("dma-pl330.0", "apb_pclk", &exynos4_clk_pdma0),
 	CLKDEV_INIT("dma-pl330.1", "apb_pclk", &exynos4_clk_pdma1),
 	CLKDEV_INIT("dma-pl330.2", "apb_pclk", &exynos4_clk_mdma1),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk0", &exynos4_clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk0", &exynos4_clk_sclk_spi1.clk),
-	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk0", &exynos4_clk_sclk_spi2.clk),
+	CLKDEV_INIT("exynos4210-spi.0", "spi_busclk0", &exynos4_clk_sclk_spi0.clk),
+	CLKDEV_INIT("exynos4210-spi.1", "spi_busclk0", &exynos4_clk_sclk_spi1.clk),
+	CLKDEV_INIT("exynos4210-spi.2", "spi_busclk0", &exynos4_clk_sclk_spi2.clk),
 };
 
 static int xtal_rate;

arch/arm/mach-exynos/clock-exynos5.c

@@ -131,6 +131,11 @@ static int exynos5_clksrc_mask_peric0_ctrl(struct clk *clk, int enable)
 	return s5p_gatectrl(EXYNOS5_CLKSRC_MASK_PERIC0, clk, enable);
 }
 
+static int exynos5_clksrc_mask_peric1_ctrl(struct clk *clk, int enable)
+{
+	return s5p_gatectrl(EXYNOS5_CLKSRC_MASK_PERIC1, clk, enable);
+}
+
 static int exynos5_clk_ip_acp_ctrl(struct clk *clk, int enable)
 {
 	return s5p_gatectrl(EXYNOS5_CLKGATE_IP_ACP, clk, enable);
@@ -740,6 +745,24 @@ static struct clk exynos5_init_clocks_off[] = {
 		.parent		= &exynos5_clk_aclk_66.clk,
 		.enable		= exynos5_clk_ip_peric_ctrl,
 		.ctrlbit	= (1 << 14),
+	}, {
+		.name		= "spi",
+		.devname	= "exynos4210-spi.0",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peric_ctrl,
+		.ctrlbit	= (1 << 16),
+	}, {
+		.name		= "spi",
+		.devname	= "exynos4210-spi.1",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peric_ctrl,
+		.ctrlbit	= (1 << 17),
+	}, {
+		.name		= "spi",
+		.devname	= "exynos4210-spi.2",
+		.parent		= &exynos5_clk_aclk_66.clk,
+		.enable		= exynos5_clk_ip_peric_ctrl,
+		.ctrlbit	= (1 << 18),
 	}, {
 		.name		= SYSMMU_CLOCK_NAME,
 		.devname	= SYSMMU_CLOCK_DEVNAME(mfc_l, 0),
@@ -1034,6 +1057,69 @@ static struct clksrc_clk exynos5_clk_sclk_mmc3 = {
 	.reg_div = { .reg = EXYNOS5_CLKDIV_FSYS2, .shift = 24, .size = 8 },
 };
 
+static struct clksrc_clk exynos5_clk_mdout_spi0 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.0",
+	},
+	.sources = &exynos5_clkset_group,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_PERIC1, .shift = 16, .size = 4 },
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk exynos5_clk_mdout_spi1 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.1",
+	},
+	.sources = &exynos5_clkset_group,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_PERIC1, .shift = 20, .size = 4 },
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 16, .size = 4 },
+};
+
+static struct clksrc_clk exynos5_clk_mdout_spi2 = {
+	.clk	= {
+		.name		= "mdout_spi",
+		.devname	= "exynos4210-spi.2",
+	},
+	.sources = &exynos5_clkset_group,
+	.reg_src = { .reg = EXYNOS5_CLKSRC_PERIC1, .shift = 24, .size = 4 },
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC2, .shift = 0, .size = 4 },
+};
+
+static struct clksrc_clk exynos5_clk_sclk_spi0 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "exynos4210-spi.0",
+		.parent		= &exynos5_clk_mdout_spi0.clk,
+		.enable		= exynos5_clksrc_mask_peric1_ctrl,
+		.ctrlbit	= (1 << 16),
+	},
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 8, .size = 8 },
+};
+
+static struct clksrc_clk exynos5_clk_sclk_spi1 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "exynos4210-spi.1",
+		.parent		= &exynos5_clk_mdout_spi1.clk,
+		.enable		= exynos5_clksrc_mask_peric1_ctrl,
+		.ctrlbit	= (1 << 20),
+	},
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC1, .shift = 24, .size = 8 },
+};
+
+static struct clksrc_clk exynos5_clk_sclk_spi2 = {
+	.clk	= {
+		.name		= "sclk_spi",
+		.devname	= "exynos4210-spi.2",
+		.parent		= &exynos5_clk_mdout_spi2.clk,
+		.enable		= exynos5_clksrc_mask_peric1_ctrl,
+		.ctrlbit	= (1 << 24),
+	},
+	.reg_div = { .reg = EXYNOS5_CLKDIV_PERIC2, .shift = 8, .size = 8 },
+};
+
 static struct clksrc_clk exynos5_clksrcs[] = {
 	{
 		.clk	= {
@@ -1148,6 +1234,12 @@ static struct clksrc_clk *exynos5_sysclks[] = {
 	&exynos5_clk_dout_mmc4,
 	&exynos5_clk_aclk_acp,
 	&exynos5_clk_pclk_acp,
+	&exynos5_clk_sclk_spi0,
+	&exynos5_clk_sclk_spi1,
+	&exynos5_clk_sclk_spi2,
+	&exynos5_clk_mdout_spi0,
+	&exynos5_clk_mdout_spi1,
+	&exynos5_clk_mdout_spi2,
 };
 
 static struct clk *exynos5_clk_cdev[] = {
@@ -1176,6 +1268,9 @@ static struct clk_lookup exynos5_clk_lookup[] = {
 	CLKDEV_INIT("exynos4-sdhci.1", "mmc_busclk.2", &exynos5_clk_sclk_mmc1.clk),
 	CLKDEV_INIT("exynos4-sdhci.2", "mmc_busclk.2", &exynos5_clk_sclk_mmc2.clk),
 	CLKDEV_INIT("exynos4-sdhci.3", "mmc_busclk.2", &exynos5_clk_sclk_mmc3.clk),
+	CLKDEV_INIT("exynos4210-spi.0", "spi_busclk0", &exynos5_clk_sclk_spi0.clk),
+	CLKDEV_INIT("exynos4210-spi.1", "spi_busclk0", &exynos5_clk_sclk_spi1.clk),
+	CLKDEV_INIT("exynos4210-spi.2", "spi_busclk0", &exynos5_clk_sclk_spi2.clk),
 	CLKDEV_INIT("dma-pl330.0", "apb_pclk", &exynos5_clk_pdma0),
 	CLKDEV_INIT("dma-pl330.1", "apb_pclk", &exynos5_clk_pdma1),
 	CLKDEV_INIT("dma-pl330.2", "apb_pclk", &exynos5_clk_mdma1),

arch/arm/mach-exynos/include/mach/irqs.h

@@ -195,6 +195,10 @@
 #define IRQ_IIC6			EXYNOS4_IRQ_IIC6
 #define IRQ_IIC7			EXYNOS4_IRQ_IIC7
 
+#define IRQ_SPI0			EXYNOS4_IRQ_SPI0
+#define IRQ_SPI1			EXYNOS4_IRQ_SPI1
+#define IRQ_SPI2			EXYNOS4_IRQ_SPI2
+
 #define IRQ_USB_HOST			EXYNOS4_IRQ_USB_HOST
 #define IRQ_OTG				EXYNOS4_IRQ_USB_HSOTG
 

arch/arm/mach-exynos/include/mach/map.h

@@ -154,6 +154,9 @@
 #define EXYNOS4_PA_SPI0			0x13920000
 #define EXYNOS4_PA_SPI1			0x13930000
 #define EXYNOS4_PA_SPI2			0x13940000
+#define EXYNOS5_PA_SPI0			0x12D20000
+#define EXYNOS5_PA_SPI1			0x12D30000
+#define EXYNOS5_PA_SPI2			0x12D40000
 
 #define EXYNOS4_PA_GPIO1		0x11400000
 #define EXYNOS4_PA_GPIO2		0x11000000

arch/arm/mach-exynos/mach-exynos4-dt.c

@@ -55,6 +55,12 @@ static const struct of_dev_auxdata exynos4210_auxdata_lookup[] __initconst = {
 				"exynos4-sdhci.3", NULL),
 	OF_DEV_AUXDATA("samsung,s3c2440-i2c", EXYNOS4_PA_IIC(0),
 				"s3c2440-i2c.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS4_PA_SPI0,
+				"exynos4210-spi.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS4_PA_SPI1,
+				"exynos4210-spi.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS4_PA_SPI2,
+				"exynos4210-spi.2", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS4_PA_PDMA1, "dma-pl330.1", NULL),
 	{},

arch/arm/mach-exynos/mach-exynos5-dt.c

@@ -47,6 +47,12 @@ static const struct of_dev_auxdata exynos5250_auxdata_lookup[] __initconst = {
 				"s3c2440-i2c.0", NULL),
 	OF_DEV_AUXDATA("samsung,s3c2440-i2c", EXYNOS5_PA_IIC(1),
 				"s3c2440-i2c.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI0,
+				"exynos4210-spi.0", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI1,
+				"exynos4210-spi.1", NULL),
+	OF_DEV_AUXDATA("samsung,exynos4210-spi", EXYNOS5_PA_SPI2,
+				"exynos4210-spi.2", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA0, "dma-pl330.0", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_PDMA1, "dma-pl330.1", NULL),
 	OF_DEV_AUXDATA("arm,pl330", EXYNOS5_PA_MDMA1, "dma-pl330.2", NULL),

arch/arm/mach-exynos/setup-spi.c

@@ -9,21 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.clk_from_cmu	= true,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(EXYNOS4_GPB(0), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(EXYNOS4_GPB(0), S3C_GPIO_PULL_UP);
@@ -34,15 +23,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.clk_from_cmu	= true,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(EXYNOS4_GPB(4), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(EXYNOS4_GPB(4), S3C_GPIO_PULL_UP);
@@ -53,15 +34,7 @@ int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI2
-struct s3c64xx_spi_info s3c64xx_spi2_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.clk_from_cmu	= true,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi2_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi2_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(EXYNOS4_GPC1(1), S3C_GPIO_SFN(5));
 	s3c_gpio_setpull(EXYNOS4_GPC1(1), S3C_GPIO_PULL_UP);

arch/arm/mach-s3c24xx/clock-s3c2416.c

@@ -144,7 +144,8 @@ static struct clk_lookup s3c2416_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.0", &hsmmc0_clk),
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &hsmmc_mux0.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &hsmmc_mux1.clk),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &hsspi_mux.clk),
+	/* s3c2443-spi.0 is used on s3c2416 and s3c2450 as well */
+	CLKDEV_INIT("s3c2443-spi.0", "spi_busclk2", &hsspi_mux.clk),
 };
 
 void __init s3c2416_init_clocks(int xtal)

arch/arm/mach-s3c24xx/clock-s3c2443.c

@@ -181,7 +181,7 @@ static struct clk *clks[] __initdata = {
 
 static struct clk_lookup s3c2443_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_hsmmc),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_hsspi.clk),
+	CLKDEV_INIT("s3c2443-spi.0", "spi_busclk2", &clk_hsspi.clk),
 };
 
 void __init s3c2443_init_clocks(int xtal)

arch/arm/mach-s3c24xx/common-s3c2443.c

@@ -559,7 +559,7 @@ static struct clk hsmmc1_clk = {
 
 static struct clk hsspi_clk = {
 	.name		= "spi",
-	.devname	= "s3c64xx-spi.0",
+	.devname	= "s3c2443-spi.0",
 	.parent		= &clk_p,
 	.enable		= s3c2443_clkcon_enable_p,
 	.ctrlbit	= S3C2443_PCLKCON_HSSPI,
@@ -633,7 +633,7 @@ static struct clk_lookup s3c2443_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_p),
 	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_esys_uart.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.0", &hsmmc1_clk),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk0", &hsspi_clk),
+	CLKDEV_INIT("s3c2443-spi.0", "spi_busclk0", &hsspi_clk),
 };
 
 void __init s3c2443_common_init_clocks(int xtal, pll_fn get_mpll,

arch/arm/mach-s3c24xx/setup-spi.c

@@ -13,20 +13,12 @@
 #include <linux/platform_device.h>
 
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #include <mach/hardware.h>
 #include <mach/regs-gpio.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.tx_st_done	= 21,
-	.high_speed	= 1,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *pdev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	/* enable hsspi bit in misccr */
 	s3c2410_modify_misccr(S3C2416_MISCCR_HSSPI_EN2, 1);

arch/arm/mach-s3c64xx/clock.c

@@ -178,13 +178,13 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= S3C_CLKCON_PCLK_KEYPAD,
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s3c6410-spi.0",
 		.parent		= &clk_p,
 		.enable		= s3c64xx_pclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_PCLK_SPI0,
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s3c6410-spi.1",
 		.parent		= &clk_p,
 		.enable		= s3c64xx_pclk_ctrl,
 		.ctrlbit	= S3C_CLKCON_PCLK_SPI1,
@@ -331,7 +331,7 @@ static struct clk init_clocks_off[] = {
 
 static struct clk clk_48m_spi0 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.0",
+	.devname	= "s3c6410-spi.0",
 	.parent		= &clk_48m,
 	.enable		= s3c64xx_sclk_ctrl,
 	.ctrlbit	= S3C_CLKCON_SCLK_SPI0_48,
@@ -339,7 +339,7 @@ static struct clk clk_48m_spi0 = {
 
 static struct clk clk_48m_spi1 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.1",
+	.devname	= "s3c6410-spi.1",
 	.parent		= &clk_48m,
 	.enable		= s3c64xx_sclk_ctrl,
 	.ctrlbit	= S3C_CLKCON_SCLK_SPI1_48,
@@ -802,7 +802,7 @@ static struct clksrc_clk clk_sclk_mmc2 = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "spi-bus",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s3c6410-spi.0",
 		.ctrlbit	= S3C_CLKCON_SCLK_SPI0,
 		.enable		= s3c64xx_sclk_ctrl,
 	},
@@ -814,7 +814,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "spi-bus",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s3c6410-spi.1",
 		.ctrlbit	= S3C_CLKCON_SCLK_SPI1,
 		.enable		= s3c64xx_sclk_ctrl,
 	},
@@ -858,10 +858,10 @@ static struct clk_lookup s3c64xx_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_48m_spi0),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_48m_spi1),
+	CLKDEV_INIT("s3c6410-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s3c6410-spi.0", "spi_busclk2", &clk_48m_spi0),
+	CLKDEV_INIT("s3c6410-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s3c6410-spi.1", "spi_busclk2", &clk_48m_spi1),
 };
 
 #define GET_DIV(clk, field) ((((clk) & field##_MASK) >> field##_SHIFT) + 1)

arch/arm/mach-s3c64xx/include/mach/dma.h

@@ -21,6 +21,7 @@
  */
 enum dma_ch {
 	/* DMA0/SDMA0 */
+	DMACH_DT_PROP = -1, /* not yet supported, do not use */
 	DMACH_UART0 = 0,
 	DMACH_UART0_SRC2,
 	DMACH_UART1,

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -799,7 +799,7 @@ static void __init crag6410_machine_init(void)
 	i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
 
 	samsung_keypad_set_platdata(&crag6410_keypad_data);
-	s3c64xx_spi0_set_platdata(&s3c64xx_spi0_pdata, 0, 1);
+	s3c64xx_spi0_set_platdata(NULL, 0, 1);
 
 	platform_add_devices(crag6410_devices, ARRAY_SIZE(crag6410_devices));
 

arch/arm/mach-s3c64xx/setup-spi.c

@@ -9,19 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S3C64XX_GPC(0), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
@@ -30,13 +21,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S3C64XX_GPC(4), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);

arch/arm/mach-s5p64x0/clock-s5p6440.c

@@ -227,13 +227,13 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 21),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 22),
@@ -467,7 +467,7 @@ static struct clksrc_clk clk_sclk_uclk = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.ctrlbit	= (1 << 20),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -479,7 +479,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.ctrlbit	= (1 << 21),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -519,8 +519,8 @@ static struct clk_lookup s5p6440_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
 	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5p64x0-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5p64x0-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),

arch/arm/mach-s5p64x0/clock-s5p6450.c

@@ -236,13 +236,13 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 17),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 21),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.parent		= &clk_pclk_low.clk,
 		.enable		= s5p64x0_pclk_ctrl,
 		.ctrlbit	= (1 << 22),
@@ -528,7 +528,7 @@ static struct clksrc_clk clk_sclk_uclk = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5p64x0-spi.0",
 		.ctrlbit	= (1 << 20),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -540,7 +540,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5p64x0-spi.1",
 		.ctrlbit	= (1 << 21),
 		.enable		= s5p64x0_sclk_ctrl,
 	},
@@ -562,8 +562,8 @@ static struct clk_lookup s5p6450_clk_lookup[] = {
 	CLKDEV_INIT(NULL, "clk_uart_baud2", &clk_pclk_low.clk),
 	CLKDEV_INIT(NULL, "clk_uart_baud3", &clk_sclk_uclk.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5p64x0-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5p64x0-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
 	CLKDEV_INIT("s3c-sdhci.0", "mmc_busclk.2", &clk_sclk_mmc0.clk),
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),

arch/arm/mach-s5p64x0/setup-spi.c

@@ -9,21 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/io.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/cpu.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	if (soc_is_s5p6450())
 		s3c_gpio_cfgall_range(S5P6450_GPC(0), 3,
@@ -36,13 +25,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	if (soc_is_s5p6450())
 		s3c_gpio_cfgall_range(S5P6450_GPC(4), 3,

arch/arm/mach-s5pc100/clock.c

@@ -564,19 +564,19 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 5),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pc100-spi.0",
 		.parent		= &clk_div_d1_bus.clk,
 		.enable		= s5pc100_d1_4_ctrl,
 		.ctrlbit	= (1 << 6),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pc100-spi.1",
 		.parent		= &clk_div_d1_bus.clk,
 		.enable		= s5pc100_d1_4_ctrl,
 		.ctrlbit	= (1 << 7),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "s5pc100-spi.2",
 		.parent		= &clk_div_d1_bus.clk,
 		.enable		= s5pc100_d1_4_ctrl,
 		.ctrlbit	= (1 << 8),
@@ -702,7 +702,7 @@ static struct clk clk_hsmmc0 = {
 
 static struct clk clk_48m_spi0 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.0",
+	.devname	= "s5pc100-spi.0",
 	.parent		= &clk_mout_48m.clk,
 	.enable		= s5pc100_sclk0_ctrl,
 	.ctrlbit	= (1 << 7),
@@ -710,7 +710,7 @@ static struct clk clk_48m_spi0 = {
 
 static struct clk clk_48m_spi1 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.1",
+	.devname	= "s5pc100-spi.1",
 	.parent		= &clk_mout_48m.clk,
 	.enable		= s5pc100_sclk0_ctrl,
 	.ctrlbit	= (1 << 8),
@@ -718,7 +718,7 @@ static struct clk clk_48m_spi1 = {
 
 static struct clk clk_48m_spi2 = {
 	.name		= "spi_48m",
-	.devname	= "s3c64xx-spi.2",
+	.devname	= "s5pc100-spi.2",
 	.parent		= &clk_mout_48m.clk,
 	.enable		= s5pc100_sclk0_ctrl,
 	.ctrlbit	= (1 << 9),
@@ -1085,7 +1085,7 @@ static struct clksrc_clk clk_sclk_mmc2 = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pc100-spi.0",
 		.ctrlbit	= (1 << 4),
 		.enable		= s5pc100_sclk0_ctrl,
 	},
@@ -1097,7 +1097,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pc100-spi.1",
 		.ctrlbit	= (1 << 5),
 		.enable		= s5pc100_sclk0_ctrl,
 	},
@@ -1109,7 +1109,7 @@ static struct clksrc_clk clk_sclk_spi1 = {
 static struct clksrc_clk clk_sclk_spi2 = {
 	.clk	= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "s5pc100-spi.2",
 		.ctrlbit	= (1 << 6),
 		.enable		= s5pc100_sclk0_ctrl,
 	},
@@ -1315,12 +1315,12 @@ static struct clk_lookup s5pc100_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.1", "mmc_busclk.2", &clk_sclk_mmc1.clk),
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_48m_spi0),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk2", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_48m_spi1),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk2", &clk_sclk_spi1.clk),
-	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk1", &clk_48m_spi2),
-	CLKDEV_INIT("s3c64xx-spi.2", "spi_busclk2", &clk_sclk_spi2.clk),
+	CLKDEV_INIT("s5pc100-spi.0", "spi_busclk1", &clk_48m_spi0),
+	CLKDEV_INIT("s5pc100-spi.0", "spi_busclk2", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5pc100-spi.1", "spi_busclk1", &clk_48m_spi1),
+	CLKDEV_INIT("s5pc100-spi.1", "spi_busclk2", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5pc100-spi.2", "spi_busclk1", &clk_48m_spi2),
+	CLKDEV_INIT("s5pc100-spi.2", "spi_busclk2", &clk_sclk_spi2.clk),
 };
 
 void __init s5pc100_register_clocks(void)

arch/arm/mach-s5pc100/setup-spi.c

@@ -9,20 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.high_speed	= 1,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S5PC100_GPB(0), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
@@ -31,14 +21,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.high_speed	= 1,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgall_range(S5PC100_GPB(4), 3,
 				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
@@ -47,14 +30,7 @@ int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI2
-struct s3c64xx_spi_info s3c64xx_spi2_pdata __initdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 13,
-	.high_speed	= 1,
-	.tx_st_done	= 21,
-};
-
-int s3c64xx_spi2_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi2_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(S5PC100_GPG3(0), S3C_GPIO_SFN(3));
 	s3c_gpio_setpull(S5PC100_GPG3(0), S3C_GPIO_PULL_UP);

arch/arm/mach-s5pv210/clock.c

@@ -445,19 +445,19 @@ static struct clk init_clocks_off[] = {
 		.ctrlbit	= (1 << 11),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pv210-spi.0",
 		.parent		= &clk_pclk_psys.clk,
 		.enable		= s5pv210_clk_ip3_ctrl,
 		.ctrlbit	= (1<<12),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pv210-spi.1",
 		.parent		= &clk_pclk_psys.clk,
 		.enable		= s5pv210_clk_ip3_ctrl,
 		.ctrlbit	= (1<<13),
 	}, {
 		.name		= "spi",
-		.devname	= "s3c64xx-spi.2",
+		.devname	= "s5pv210-spi.2",
 		.parent		= &clk_pclk_psys.clk,
 		.enable		= s5pv210_clk_ip3_ctrl,
 		.ctrlbit	= (1<<14),
@@ -1035,7 +1035,7 @@ static struct clksrc_clk clk_sclk_mmc3 = {
 static struct clksrc_clk clk_sclk_spi0 = {
 	.clk		= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.0",
+		.devname	= "s5pv210-spi.0",
 		.enable		= s5pv210_clk_mask0_ctrl,
 		.ctrlbit	= (1 << 16),
 	},
@@ -1047,7 +1047,7 @@ static struct clksrc_clk clk_sclk_spi0 = {
 static struct clksrc_clk clk_sclk_spi1 = {
 	.clk		= {
 		.name		= "sclk_spi",
-		.devname	= "s3c64xx-spi.1",
+		.devname	= "s5pv210-spi.1",
 		.enable		= s5pv210_clk_mask0_ctrl,
 		.ctrlbit	= (1 << 17),
 	},
@@ -1331,8 +1331,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = {
 	CLKDEV_INIT("s3c-sdhci.2", "mmc_busclk.2", &clk_sclk_mmc2.clk),
 	CLKDEV_INIT("s3c-sdhci.3", "mmc_busclk.2", &clk_sclk_mmc3.clk),
 	CLKDEV_INIT(NULL, "spi_busclk0", &clk_p),
-	CLKDEV_INIT("s3c64xx-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
-	CLKDEV_INIT("s3c64xx-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
+	CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk),
+	CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk),
 };
 
 void __init s5pv210_register_clocks(void)

arch/arm/mach-s5pv210/setup-spi.c

@@ -9,20 +9,10 @@
  */
 
 #include <linux/gpio.h>
-#include <linux/platform_device.h>
-
 #include <plat/gpio-cfg.h>
-#include <plat/s3c64xx-spi.h>
 
 #ifdef CONFIG_S3C64XX_DEV_SPI0
-struct s3c64xx_spi_info s3c64xx_spi0_pdata = {
-	.fifo_lvl_mask	= 0x1ff,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi0_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(S5PV210_GPB(0), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(S5PV210_GPB(0), S3C_GPIO_PULL_UP);
@@ -33,14 +23,7 @@ int s3c64xx_spi0_cfg_gpio(struct platform_device *dev)
 #endif
 
 #ifdef CONFIG_S3C64XX_DEV_SPI1
-struct s3c64xx_spi_info s3c64xx_spi1_pdata = {
-	.fifo_lvl_mask	= 0x7f,
-	.rx_lvl_offset	= 15,
-	.high_speed	= 1,
-	.tx_st_done	= 25,
-};
-
-int s3c64xx_spi1_cfg_gpio(struct platform_device *dev)
+int s3c64xx_spi1_cfg_gpio(void)
 {
 	s3c_gpio_cfgpin(S5PV210_GPB(4), S3C_GPIO_SFN(2));
 	s3c_gpio_setpull(S5PV210_GPB(4), S3C_GPIO_PULL_UP);

arch/arm/plat-samsung/devs.c

@@ -1512,7 +1512,7 @@ static struct resource s3c64xx_spi0_resource[] = {
 };
 
 struct platform_device s3c64xx_device_spi0 = {
-	.name		= "s3c64xx-spi",
+	.name		= "s3c6410-spi",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(s3c64xx_spi0_resource),
 	.resource	= s3c64xx_spi0_resource,
@@ -1522,13 +1522,10 @@ struct platform_device s3c64xx_device_spi0 = {
 	},
 };
 
-void __init s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs)
+void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
 {
-	if (!pd) {
-		pr_err("%s:Need to pass platform data\n", __func__);
-		return;
-	}
+	struct s3c64xx_spi_info pd;
 
 	/* Reject invalid configuration */
 	if (!num_cs || src_clk_nr < 0) {
@@ -1536,12 +1533,11 @@ void __init s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
 		return;
 	}
 
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	if (!pd->cfg_gpio)
-		pd->cfg_gpio = s3c64xx_spi0_cfg_gpio;
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi0_cfg_gpio;
 
-	s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi0);
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi0);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI0 */
 
@@ -1554,7 +1550,7 @@ static struct resource s3c64xx_spi1_resource[] = {
 };
 
 struct platform_device s3c64xx_device_spi1 = {
-	.name		= "s3c64xx-spi",
+	.name		= "s3c6410-spi",
 	.id		= 1,
 	.num_resources	= ARRAY_SIZE(s3c64xx_spi1_resource),
 	.resource	= s3c64xx_spi1_resource,
@@ -1564,26 +1560,20 @@ struct platform_device s3c64xx_device_spi1 = {
 	},
 };
 
-void __init s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs)
+void __init s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
 {
-	if (!pd) {
-		pr_err("%s:Need to pass platform data\n", __func__);
-		return;
-	}
-
 	/* Reject invalid configuration */
 	if (!num_cs || src_clk_nr < 0) {
 		pr_err("%s: Invalid SPI configuration\n", __func__);
 		return;
 	}
 
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	if (!pd->cfg_gpio)
-		pd->cfg_gpio = s3c64xx_spi1_cfg_gpio;
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi1_cfg_gpio;
 
-	s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi1);
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi1);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI1 */
 
@@ -1596,7 +1586,7 @@ static struct resource s3c64xx_spi2_resource[] = {
 };
 
 struct platform_device s3c64xx_device_spi2 = {
-	.name		= "s3c64xx-spi",
+	.name		= "s3c6410-spi",
 	.id		= 2,
 	.num_resources	= ARRAY_SIZE(s3c64xx_spi2_resource),
 	.resource	= s3c64xx_spi2_resource,
@@ -1606,13 +1596,10 @@ struct platform_device s3c64xx_device_spi2 = {
 	},
 };
 
-void __init s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs)
+void __init s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs)
 {
-	if (!pd) {
-		pr_err("%s:Need to pass platform data\n", __func__);
-		return;
-	}
+	struct s3c64xx_spi_info pd;
 
 	/* Reject invalid configuration */
 	if (!num_cs || src_clk_nr < 0) {
@@ -1620,11 +1607,10 @@ void __init s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
 		return;
 	}
 
-	pd->num_cs = num_cs;
-	pd->src_clk_nr = src_clk_nr;
-	if (!pd->cfg_gpio)
-		pd->cfg_gpio = s3c64xx_spi2_cfg_gpio;
+	pd.num_cs = num_cs;
+	pd.src_clk_nr = src_clk_nr;
+	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi2_cfg_gpio;
 
-	s3c_set_platdata(pd, sizeof(*pd), &s3c64xx_device_spi2);
+	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi2);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI2 */

arch/arm/plat-samsung/include/plat/s3c64xx-spi.h

@@ -18,7 +18,6 @@ struct platform_device;
  * @fb_delay: Slave specific feedback delay.
  *            Refer to FB_CLK_SEL register definition in SPI chapter.
  * @line: Custom 'identity' of the CS line.
- * @set_level: CS line control.
  *
  * This is per SPI-Slave Chipselect information.
  * Allocate and initialize one in machine init code and make the
@@ -27,57 +26,41 @@ struct platform_device;
 struct s3c64xx_spi_csinfo {
 	u8 fb_delay;
 	unsigned line;
-	void (*set_level)(unsigned line_id, int lvl);
 };
 
 /**
  * struct s3c64xx_spi_info - SPI Controller defining structure
  * @src_clk_nr: Clock source index for the CLK_CFG[SPI_CLKSEL] field.
- * @clk_from_cmu: If the SPI clock/prescalar control block is present
- *     by the platform's clock-management-unit and not in SPI controller.
  * @num_cs: Number of CS this controller emulates.
  * @cfg_gpio: Configure pins for this SPI controller.
- * @fifo_lvl_mask: All tx fifo_lvl fields start at offset-6
- * @rx_lvl_offset: Depends on tx fifo_lvl field and bus number
- * @high_speed: If the controller supports HIGH_SPEED_EN bit
- * @tx_st_done: Depends on tx fifo_lvl field
  */
 struct s3c64xx_spi_info {
 	int src_clk_nr;
-	bool clk_from_cmu;
-
 	int num_cs;
-
-	int (*cfg_gpio)(struct platform_device *pdev);
-
-	/* Following two fields are for future compatibility */
-	int fifo_lvl_mask;
-	int rx_lvl_offset;
-	int high_speed;
-	int tx_st_done;
+	int (*cfg_gpio)(void);
 };
 
 /**
  * s3c64xx_spi_set_platdata - SPI Controller configure callback by the board
  *				initialization code.
- * @pd: SPI platform data to set.
+ * @cfg_gpio: Pointer to gpio setup function.
  * @src_clk_nr: Clock the SPI controller is to use to generate SPI clocks.
  * @num_cs: Number of elements in the 'cs' array.
  *
  * Call this from machine init code for each SPI Controller that
  * has some chips attached to it.
  */
-extern void s3c64xx_spi0_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs);
-extern void s3c64xx_spi1_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs);
-extern void s3c64xx_spi2_set_platdata(struct s3c64xx_spi_info *pd,
-				      int src_clk_nr, int num_cs);
+extern void s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs);
+extern void s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs);
+extern void s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
+						int num_cs);
 
 /* defined by architecture to configure gpio */
-extern int s3c64xx_spi0_cfg_gpio(struct platform_device *dev);
-extern int s3c64xx_spi1_cfg_gpio(struct platform_device *dev);
-extern int s3c64xx_spi2_cfg_gpio(struct platform_device *dev);
+extern int s3c64xx_spi0_cfg_gpio(void);
+extern int s3c64xx_spi1_cfg_gpio(void);
+extern int s3c64xx_spi2_cfg_gpio(void);
 
 extern struct s3c64xx_spi_info s3c64xx_spi0_pdata;
 extern struct s3c64xx_spi_info s3c64xx_spi1_pdata;